Abstract: This paper puts forward one kind of air-fuel ratio
control method with PI controller. With the help of
MATLAB/SIMULINK software, the mathematical model of air-fuel
ratio control system for distributorless CNG engine is constructed.
The objective is to maintain cylinder-to-cylinder air-fuel ratio at a
prescribed set point, determined primarily by the state of the Three-
Way-Catalyst (TWC), so that the pollutants in the exhaust are
removed with the highest efficiency. The concurrent control of airfuel
under transient conditions could be implemented by Proportional
and Integral (PI) controller. The simulation result indicates that the
control methods can easily eliminate the air/fuel maldistribution and
maintain the air/fuel ratio at the stochiometry within minimum
engine events.
Abstract: The mobile users with Laptops need to have an
efficient access to i.e. their home personal data or to the Internet from
any place in the world, regardless of their location or point of
attachment, especially while roaming outside the home subnet. An
efficient interpretation of packet losses problem that is encountered
from this roaming is to the centric of all aspects in this work, to be
over-highlighted. The main previous works, such as BER-systems,
Amigos, and ns-2 implementation that are considered to be in
conjunction with that problem under study are reviewed and
discussed. Their drawbacks and limitations, of stopping only at
monitoring, and not to provide an actual solution for eliminating or
even restricting these losses, are mentioned. Besides that, the
framework around which we built a Triple-R sequence as a costeffective
solution to eliminate the packet losses and bridge the gap
between subnets, an area that until now has been largely neglected, is
presented. The results show that, in addition to the high bit error rate
of wireless mobile networks, mainly the low efficiency of mobile-IP
registration procedure is a direct cause of these packet losses.
Furthermore, the output of packet losses interpretation resulted an
illustrated triangle of the registration process. This triangle should be
further researched and analyzed in our future work.
Abstract: The effect of the blade tip geometry of a high pressure
gas turbine is studied experimentally and computationally for high
speed leakage flows. For this purpose two simplified models are
constructed, one models a flat tip of the blade and the second models
a cavity tip of the blade. Experimental results are obtained from a
transonic wind tunnel to show the static pressure distribution along
the tip wall and provide flow visualization. RANS computations
were carried to provide further insight into the mean flow behavior
and to calculate the discharge coefficient which is a measure of the
flow leaking over the tip. It is shown that in both geometries of tip
the flow separates over the tip to form a separation bubble. The
bubble is higher for the cavity tip while a complete shock wave
system of oblique waves ending with a normal wave can be seen for
the flat tip. The discharge coefficient for the flat tip shows less
dependence on the pressure ratio over the blade tip than the cavity
tip. However, the discharge coefficient for the cavity tip is lower than
that of the flat tip, showing a better ability to reduce the leakage flow
and thus increase the turbine efficiency.
Abstract: The objective of this paper is to a design of pattern
classification model based on the back-propagation (BP) algorithm for
decision support system. Standard BP model has done full connection
of each node in the layers from input to output layers. Therefore, it
takes a lot of computing time and iteration computing for good
performance and less accepted error rate when we are doing some
pattern generation or training the network.
However, this model is using exclusive connection in between
hidden layer nodes and output nodes. The advantage of this model is
less number of iteration and better performance compare with standard
back-propagation model. We simulated some cases of classification
data and different setting of network factors (e.g. hidden layer number
and nodes, number of classification and iteration). During our
simulation, we found that most of simulations cases were satisfied by
BP based using exclusive connection network model compared to
standard BP. We expect that this algorithm can be available to
identification of user face, analysis of data, mapping data in between
environment data and information.
Abstract: Tourism industries are rapidly increased for the last
few years especially in Malaysia. In order to attract more tourists,
Malaysian Governance encourages any effort to increase Malaysian
tourism industry. One of the efforts in attracting more tourists in
Malacca, Malaysia is a duck tour. Duck tour is an amphibious
sightseeing tour that works in two types of engines, hence, it required
a huge cost to operate and maintain the vehicle. To other country, it is
not so new but in Malaysia, it is just introduced, thus it does not have
any systematic routing yet. Therefore, this paper proposed an
optimization technique to formulate and schedule this tour to
minimize the operating costs by considering it into Travelling
Salesman Problem (TSP). The problem is then can be solved by one
of the optimization technique especially meta-heuristics approach
such as Tabu Search (TS) and Reactive Tabu Search (RTS).
Abstract: This paper presents anapproach of hybridizing two or more artificial intelligence (AI) techniques which arebeing used to
fuzzify the workstress level ranking and categorize the rating accordingly. The use of two or more techniques (hybrid approach)
has been considered in this case, as combining different techniques may lead to neutralizing each other-s weaknesses generating a
superior hybrid solution. Recent researches have shown that there is a
need for a more valid and reliable tools, for assessing work stress. Thus artificial intelligence techniques have been applied in this
instance to provide a solution to a psychological application. An overview about the novel and autonomous interactive model for analysing work-stress that has been developedusing multi-agent
systems is also presented in this paper. The establishment of the intelligent multi-agent decision analyser (IMADA) using hybridized technique of neural networks and fuzzy logic within the multi-agent based framework is also described.
Abstract: In the current Grid environment, efficient workload
management presents a significant challenge, for which there are
exorbitant de facto standards encompassing resource discovery,
brokerage, and data transfer, among others. In addition, the real-time
resource status, essential for an optimal resource allocation strategy,
is often not readily accessible. To address these issues and provide a
cleaner abstraction of the Grid with the potential of generalizing into
arbitrary resource-sharing environment, this paper proposes a new
Condor-based pilot mechanism applied in the PanDA architecture,
PanDA-PF WMS, with the goal of providing a more generic yet
efficient resource allocating strategy. In this architecture, the PanDA
server primarily acts as a repository of user jobs, responding to pilot
requests from distributed, remote resources. Scheduling decisions are
subsequently made according to the real-time resource information
reported by pilots. Pilot Factory is a Condor-inspired solution for a
scalable pilot dissemination and effectively functions as a resource
provisioning mechanism through which the user-job server, PanDA,
reaches out to the candidate resources only on demand.
Abstract: Importance of environmental efficiency of electric power industry stems from high demand for energy combined with global warming concerns. It is especially essential for the world largest economies like that of the United States. The paper introduces a Data Envelopment Analysis (DEA) model of environmental efficiency using indicators of fossil fuels utilization, emissions rate, and electric power losses. Using DEA is advantageous in this situation over other approaches due to its nonparametric nature. The paper analyzes data for the period of 1990 - 2006 by comparing actual yearly levels in each dimension with the best values of partial indicators for the period. As positive factors of efficiency, tendency to the decline in emissions rates starting 2000, and in electric power losses starting 2004 may be mentioned together with increasing trend of fuel utilization starting 1999. As a result, dynamics of environmental efficiency is positive starting 2002. The main concern is the decline in fossil fuels utilization in 2006. This negative change should be reversed to comply with ecological and economic requirements.
Abstract: A simultaneous study on indoor and outdoor particulate matter concentrations was done in five elementary schools in central parts of Tehran, Iran. Three sizes of particles including PM10, PM2.5 and PM1.0 were measured in 13 classrooms within this schools during winter (January, February and March) 2009. A laserbased portable aerosol spectrometer Model Grimm-1.108, was used for the continuous measurement of particles. The average indoor concentration of PM10, PM2.5 and PM1.0 in studied schools were 274 μg/m3, 42 μg/m3 and 19 μg/m3 respectively; and average outdoor concentrations of PM10, PM2.5 and PM1.0 were evaluated to be 22 μg/m3, 38 μg/m3 and 140 μg/m3 respectively.
Abstract: When trying to enumerate all BIBD-s for given parameters,
their natural solution space appears to be huge and grows extremely with the number of points of the design. Therefore,
constructive enumerations are often carried out by assuming additional
constraints on design-s structure, automorphisms being mostly used ones. It remains a hard task to construct designs with trivial
automorphism group – those with no additional symmetry – although it is believed that most of the BIBD-s belong to that case. In
this paper, very many new designs with parameters 2-(13, 5, 5), 2-(16, 6, 5) and 2-(21, 6, 4) are constructed, assuming an action of an
automorphism of order 3. Even more, it was possible to construct millions of such designs with no non-trivial automorphisms.
Abstract: Recently, there are significant improvements in the
capabilities of mobile devices; rendering large terrain is tedious
because of the constraint in resources of mobile devices. This
paper focuses on the implementation of terrain rendering on
mobile device to observe some issues and current constraints
occurred. Experiments are performed using two datasets with
results based on rendering speed and appearance to ascertain both
the issues and constraints. The result shows a downfall of frame
rate performance because of the increase of triangles. Since the
resolution between computer and mobile device is different, the
terrain surface on mobile device looks more unrealistic compared
to on a computer. Thus, more attention in the development of
terrain rendering on mobile devices is required. The problems
highlighted in this paper will be the focus of future research and
will be a great importance for 3D visualization on mobile device.
Abstract: Software metric is a measure of some property of a
piece of software or its specification. The aim of this paper is to
present an application of evolutionary decision trees in software
engineering in order to classify the software modules that have or
have not one or more reported defects. For this some metrics are used
for detecting the class of modules with defects or without defects.
Abstract: Avoidable unscheduled maintenance events and unnecessary
spare parts deliveries are mostly caused by an incorrect choice
of the underlying maintenance strategy. For a faster and more efficient
supply of spare parts for aircrafts of an airline we examine options for
improving the underlying logistics network integrated in an existing
aviation industry network. This paper presents a dynamic prediction
model as decision support for maintenance method selection considering
requirements of an entire flight network. The objective is
to guarantee a high supply of spare parts by an optimal interaction
of various network levels and thus to reduce unscheduled maintenance
events and minimize total costs. By using a prognostics-based
preventive maintenance strategy unscheduled component failures are
avoided for an increase in availability and reliability of the entire
system. The model is intended for use in an aviation company that
utilizes a structured planning process based on collected failures data
of components.
Abstract: Eight heavy metals (Cu, Cr, Zn, Hg, Pb, Cd, Ni and As) were analyzed in sediment samples in the dry and wet seasons from November 2009 to October 2010 in West Port of Peninsular Malaysia. The heavy metal concentrations (mg/kg dry weight) were ranged from 23.4 to 98.3 for Zn, 22.3 to 80 for Pb, 7.4 to 27.6 Cu, 0.244 to 3.53 for Cd, 7.2 to 22.2 for Ni, 20.2 to 162 for As, 0.11 to 0.409 for Hg and 11.5 to 61.5 for Cr. Metals concentrations in dry season were higher than the rainy season except in cupper and chromium. Analysis of variance with Statistical Analysis System (SAS) shows that the mean concentration of metals in the two seasons (α level=0.05) are not significantly different which shows that the metals were held firmly in the matrix of sediment. Also there are significant differences between control point station with other stations. According to the Interim Sediment Quality guidelines (ISQG), the metal concentrations are moderately polluted, except in arsenic which shows the highest level of pollution.
Abstract: Cantilever L-shaped walls are known to be relatively economical as retaining solution. The design starts by proportioning the wall dimensions for which the stability is checked for. A ratio between the lengths of the base and the stem, falling between 0.5 to 0.7 ensure in most case the stability requirements, however, the displacement pattern of the wall in terms of rotations and translations, and the lateral pressure profile, do not have the same figure for all wall’s proportioning, as it is usually assumed. In the present work the results of a numerical analysis are presented, different wall geometries were considered. The results show that the proportioning governs the equilibrium between the instantaneous rotation and the translation of the wall-toe, also, the lateral pressure estimation based on the average value between the at-rest and the active pressure, recommended by most design standards, is found to be not applicable for all walls.
Abstract: Fuzzy Load forecasting plays a paramount role in the operation and management of power systems. Accurate estimation of future power demands for various lead times facilitates the task of generating power reliably and economically. The forecasting of future loads for a relatively large lead time (months to few years) is studied here (long term load forecasting). Among the various techniques used in forecasting load, artificial intelligence techniques provide greater accuracy to the forecasts as compared to conventional techniques. Fuzzy Logic, a very robust artificial intelligent technique, is described in this paper to forecast load on long term basis. The paper gives a general algorithm to forecast long term load. The algorithm is an Extension of Short term load forecasting method to Long term load forecasting and concentrates not only on the forecast values of load but also on the errors incorporated into the forecast. Hence, by correcting the errors in the forecast, forecasts with very high accuracy have been achieved. The algorithm, in the paper, is demonstrated with the help of data collected for residential sector (LT2 (a) type load: Domestic consumers). Load, is determined for three consecutive years (from April-06 to March-09) in order to demonstrate the efficiency of the algorithm and to forecast for the next two years (from April-09 to March-11).
Abstract: Finding the shortest path between two positions is a
fundamental problem in transportation, routing, and communications
applications. In robot motion planning, the robot should pass around
the obstacles touching none of them, i.e. the goal is to find a
collision-free path from a starting to a target position. This task has
many specific formulations depending on the shape of obstacles,
allowable directions of movements, knowledge of the scene, etc.
Research of path planning has yielded many fundamentally different
approaches to its solution, mainly based on various decomposition
and roadmap methods. In this paper, we show a possible use of
visibility graphs in point-to-point motion planning in the Euclidean
plane and an alternative approach using Voronoi diagrams that
decreases the probability of collisions with obstacles. The second
application area, investigated here, is focused on problems of finding
minimal networks connecting a set of given points in the plane using
either only straight connections between pairs of points (minimum
spanning tree) or allowing the addition of auxiliary points to the set
to obtain shorter spanning networks (minimum Steiner tree).
Abstract: The article touches upon questions of information security in Russian Economy. It covers theoretical bases of information security and causes of its development. The theory is proved by the analysis of business activities and the main tendencies of information security development. Perm region has been chosen as the bases for the analysis, being the fastestdeveloping region that uses methods of information security in managing it economy. As a result of the study the authors of the given article have formulated their own vision of the problem of information security in various branches of economy and stated prospects of information security development and its growing role in Russian economy
Abstract: The paper investigates the feasibility of constructing a software multi-agent based monitoring and classification system and utilizing it to provide an automated and accurate classification of end users developing applications in the spreadsheet domain. The agents function autonomously to provide continuous and periodic monitoring of excels spreadsheet workbooks. Resulting in, the development of the MultiAgent classification System (MACS) that is in compliance with the specifications of the Foundation for Intelligent Physical Agents (FIPA). However, different technologies have been brought together to build MACS. The strength of the system is the integration of the agent technology with the FIPA specifications together with other technologies that are Windows Communication Foundation (WCF) services, Service Oriented Architecture (SOA), and Oracle Data Mining (ODM). The Microsoft's .NET widows service based agents were utilized to develop the monitoring agents of MACS, the .NET WCF services together with SOA approach allowed the distribution and communication between agents over the WWW that is in order to satisfy the monitoring and classification of the multiple developer aspect. ODM was used to automate the classification phase of MACS.
Abstract: This paper aims to present knowledge management for solving economic problem and poverty in Thai community. A community in Thailand is studied as a case study for master plan or social and economic plan which derived form the research people conducted by themselves in their community. The result shows that community uses knowledge management in recording income and expense, analyzing their consumption, and then systematic planning of the production, distribution and consumption in the community. Besides, community enterprises, that people create as the by-products of master plan, can facilitate diverse economic activities which are able to reduce economic problem and poverty. The knowledge that people gain from solving their problem through building community enterprises are both tacit and explicit knowledge. Four styles of knowledge conversion: socialization,externalization, combination and internalization, are used. Besides, knowledge sharing inside the organization, between organizations and its environment are found. Keywordsknowledge management, community enterprise, Thailand.