Abstract: This paper presents an effective traffic lights detection
method at the night-time. First, candidate blobs of traffic lights are
extracted from RGB color image. Input image is represented on the
dominant color domain by using color transform proposed by Ruta,
then red and green color dominant regions are selected as candidates.
After candidate blob selection, we carry out shape filter for noise
reduction using information of blobs such as length, area, area of
boundary box, etc. A multi-class classifier based on SVM (Support
Vector Machine) applies into the candidates. Three kinds of features
are used. We use basic features such as blob width, height, center
coordinate, area, area of blob. Bright based stochastic features are also
used. In particular, geometric based moment-s values between
candidate region and adjacent region are proposed and used to improve
the detection performance. The proposed system is implemented on
Intel Core CPU with 2.80 GHz and 4 GB RAM and tested with the
urban and rural road videos. Through the test, we show that the
proposed method using PF, BMF, and GMF reaches up to 93 % of
detection rate with computation time of in average 15 ms/frame.
Abstract: The electrokinetic flow resistance (electroviscous
effect) is predicted for steady state, pressure-driven liquid flow at
low Reynolds number in a microfluidic contraction of rectangular
cross-section. Calculations of the three dimensional flow are
performed in parallel using a finite volume numerical method. The
channel walls are assumed to carry a uniform charge density and the
liquid is taken to be a symmetric 1:1 electrolyte. Predictions are
presented for a single set of flow and electrokinetic parameters. It is
shown that the magnitude of the streaming potential gradient and the
charge density of counter-ions in the liquid is greater than that in
corresponding two-dimensional slit-like contraction geometry. The
apparent viscosity is found to be very close to the value for a
rectangular channel of uniform cross-section at the chosen Reynolds
number (Re = 0.1). It is speculated that the apparent viscosity for the
contraction geometry will increase as the Reynolds number is
reduced.
Abstract: A new hybrid coding method for compressing
animated polygonal meshes is presented. This paper assumes
the simplistic representation of the geometric data: a temporal
sequence of polygonal meshes for each discrete frame of the
animated sequence. The method utilizes a delta coding and an
octree-based method. In this hybrid method, both the octree
approach and the delta coding approach are applied to each
single frame in the animation sequence in parallel. The
approach that generates the smaller encoded file size is chosen
to encode the current frame. Given the same quality
requirement, the hybrid coding method can achieve much
higher compression ratio than the octree-only method or the
delta-only method. The hybrid approach can represent 3D
animated sequences with higher compression factors while
maintaining reasonable quality. It is easy to implement and have
a low cost encoding process and a fast decoding process, which
make it a better choice for real time application.
Abstract: Aim of this work was to compare the efficacy of two
loading methods of proteins onto polymeric nanocarriers: adsorption
and encapsulation methods. Preliminary studies of protein loading
were done using Bovine Serum Albumin (BSA) as model protein.
Nanocarriers were prepared starting from polylactic co-glycolic acid
(PLGA) polymer; production methods used are two different variants
of emulsion evaporation method. Nanoparticles obtained were
analyzed in terms of dimensions by Dynamic Light Scattering and
Loading Efficiency of BSA by Bradford Assay. Loaded
nanoparticles were then submitted to in-vitro protein dissolution test
in order to study the effect of the delivery system on the release rate
of the protein.
Abstract: Response surface methodology with Box–Benhken (BB) design of experiment approach has been utilized to study the mechanism of interface slip damping in layered and jointed tack welded beams with varying surface roughness. The design utilizes the initial amplitude of excitation, tack length and surface roughness at the interfaces to develop the model for the logarithmic damping decrement of the layered and jointed welded structures. Statistically designed experiments have been performed to estimate the coefficients in the mathematical model, predict the response, and check the adequacy of the model. Comparison of predicted and experimental response values outside the design conditions have shown good correspondence, implying that empirical model derived from response surface approach can be effectively used to describe the mechanism of interface slip damping in layered and jointed tack welded structures.
Abstract: The MFCAV Riemann solver is practically used in many Lagrangian or ALE methods due to its merit of sharp shock profiles and rarefaction corners, though very often with numerical oscillations. By viewing it as a modification of the WWAM Riemann solver, we apply the MFCAV Riemann solver to the Lagrangian method recently developed by Maire. P. H et. al.. The numerical experiments show that the application is successful in that the shock profiles and rarefaction corners are sharpened compared with results obtained using other Riemann solvers. Though there are still numerical oscillations, they are within the range of the MFCAV applied in onther Lagrangian methods.
Abstract: The purpose of my research proposal is to
demonstrate that there is a relationship between EEG and
endometrial cancer.
The above relationship is based on an Aristotelian Syllogism;
since it is known that the 14-3-3 protein is related to the electrical
activity of the brain via control of the flow of Na+ and K+ ions and
since it is also known that many types of cancer are associated with
14-3-3 protein, it is possible that there is a relationship between EEG
and cancer. This research will be carried out by well-defined
diagnostic indicators, obtained via the EEG, using signal processing
procedures and pattern recognition tools such as neural networks in
order to recognize the endometrial cancer type. The current research
shall compare the findings from EEG and hysteroscopy performed on
women of a wide age range. Moreover, this practice could be
expanded to other types of cancer. The implementation of this
methodology will be completed with the creation of an ontology.
This ontology shall define the concepts existing in this research-s
domain and the relationships between them. It will represent the
types of relationships between hysteroscopy and EEG findings.
Abstract: Predictions of flow and heat transfer characteristics and shape optimization in internally finned circular tubes have been performed on three-dimensional periodically fully developed turbulent flow and thermal fields. For a trapezoidal fin profile, the effects of fin height h, upper fin widths d1, lower fin widths d2, and helix angle of fin ? on transport phenomena are investigated for the condition of fin number of N = 30. The CFD and mathematical optimization technique are coupled in order to optimize the shape of internally finned tube. The optimal solutions of the design variables (i.e., upper and lower fin widths, fin height and helix angle) are numerically obtained by minimizing the pressure loss and maximizing the heat transfer rate, simultaneously, for the limiting conditions of d1 = 0.5~1.5 mm, d2 = 0.5~1.5 mm, h= 0.5~1.5mm, ? = 10~30 degrees. The fully developed flow and thermal fields are predicted using the finite volume method and the optimization is carried out by means of the multi-objective genetic algorithm that is widely used in the constrained nonlinear optimization problem.
Abstract: In conventional seedling production, the seedlings are
being grown in the open field under natural conditions. Here they are
susceptible to sudden changes in climate were their quality and yield
is affected. Quality seedlings are essential for good growth and
performance of crops in main field; they serve as a foundation for the
economic returns to the farmer. Producing quality seedling demands
usage of hybrid seeds as they have the ability to result in better yield,
greater uniformity, improved color, disease resistance, and so forth.
Hybrid seed production poses major operational challenge and its
seed use efficiency plays an important role. Thus in order to
overcome the difficulties currently present in conventional seedling
production and to efficiently use hybrid seeds, ITC Limited Agri
Business Divisions - Sustainability Cell as conceptualized a novel
method of seedling production unit for farmers in West Godavari
District of Andhra Pradesh. The “Green House based Float Seedling"
methodology aims at a protected cultivation technique wherein the
micro climate surrounding the plant/seedling body is controlled
partially or fully as per the requirement of the species. This paper
reports on the techno economic evaluation of green house for
cultivation of float based seedling production with experimental
results that was attained from the pilot implementation in West
Godavari District, Rajahmundry region of India.
Abstract: FW4 is a newly developed hot die material widely
used in Forging Dies manufacturing. The right selection of the
machining conditions is one of the most important aspects to take
into consideration in the Electrical Discharge Machining (EDM) of
FW4. In this paper an attempt has been made to develop
mathematical models for relating the Material Removal Rate (MRR),
Tool Wear Ratio (TWR) and surface roughness (Ra) to machining
parameters (current, pulse-on time and voltage). Furthermore, a study
was carried out to analyze the effects of machining parameters in
respect of listed technological characteristics. The results of analysis
of variance (ANOVA) indicate that the proposed mathematical
models, can adequately describe the performance within the limits of
the factors being studied.
Abstract: The Institute of Product Development is dealing
with the development, design and dimensioning of micro components
and systems as a member of the Collaborative Research
Centre 499 “Design, Production and Quality Assurance of
Molded micro components made of Metallic and Ceramic Materials".
Because of technological restrictions in the miniaturization
of conventional manufacturing techniques, shape and
material deviations cannot be scaled down in the same proportion
as the micro parts, rendering components with relatively
wide tolerance fields. Systems that include such components
should be designed with this particularity in mind, often requiring
large clearance. On the end, the output of such systems
results variable and prone to dynamical instability. To save
production time and resources, every study of these effects
should happen early in the product development process and
base on computer simulation to avoid costly prototypes. A
suitable method is proposed here and exemplary applied to a
micro technology demonstrator developed by the CRC499. It
consists of a one stage planetary gear train in a sun-planet-ring
configuration, with input through the sun gear and output
through the carrier. The simulation procedure relies on ordinary
Multi Body Simulation methods and subsequently adds
other techniques to further investigate details of the system-s
behavior and to predict its response. The selection of the relevant
parameters and output functions followed the engineering
standards for regular sized gear trains. The first step is to
quantify the variability and to reveal the most critical points of
the system, performed through a whole-mechanism Sensitivity
Analysis. Due to the lack of previous knowledge about the system-s
behavior, different DOE methods involving small and
large amount of experiments were selected to perform the SA.
In this particular case the parameter space can be divided into
two well defined groups, one of them containing the gear-s profile
information and the other the components- spatial location.
This has been exploited to explore the different DOE techniques
more promptly. A reduced set of parameters is derived for
further investigation and to feed the final optimization process,
whether as optimization parameters or as external perturbation
collective. The 10 most relevant perturbation factors and 4 to 6
prospective variable parameters are considered in a new, simplified
model. All of the parameters are affected by the mentioned
production variability. The objective functions of interest
are based on scalar output-s variability measures, so the
problem becomes an optimization under robustness and reliability constrains. The study shows an initial step on the development
path of a method to design and optimize complex micro
mechanisms composed of wide tolerated elements accounting
for the robustness and reliability of the systems- output.
Abstract: In this study Homotopy Perturbation Method (HPM) is employed to investigate free vibration of an Euler beam with variable stiffness resting on an elastic foundation. HPM is an easy-to-use and very efficient technique for the solution of linear or nonlinear problems. HPM produces analytical approximate expression which is continuous in the solution domain. This work shows that HPM is a promising method for free vibration analysis of nonuniform Euler beams on elastic foundation. Several case problems have been solved by using the technique and solutions have been compared with those available in the literature.
Abstract: Utilization of various sensors has made it possible to
extend capabilities of industrial robots. Among these are vision
sensors that are used for providing visual information to assist robot
controllers. This paper presents a method of integrating a vision
system and a simulation program with an industrial robot. The vision
system is employed to detect a target object and compute its location
in the robot environment. Then, the target object-s information is sent
to the robot controller via parallel communication port. The robot
controller uses the extracted object information and the simulation
program to control the robot arm for approaching, grasping and
relocating the object. This paper presents technical details of system
components and describes the methodology used for this integration.
It also provides a case study to prove the validity of the methodology
developed.
Abstract: The phylogenetic analysis using the most conservative
portions of 18S rRNA gene revealed the phylogenetic relationship
among the two populations where DNA divergence showed that the
nucleotides diversity value were -0.00838 for the Tanjung Dawai,
Kedah and -0.00708 for the Cherating, Pahang populations
respectively. The net nucleotide divergence among populations (Da)
was -0.0073 indicating a low polymorphism among the populations
studied. Total number of mutations in the Tanjung Dawai, Kedah
samples was higher than Cherating, Pahang samples, which are 73 and
59 respectively while shared mutations across the populations were 8,
and reveal the evolutionary in the genome of Malaysian T. gigas. The
tree topology of both populations inferred using Neigbour-joining
method by comparing 1791 bp of partial 18S rRNA sequence revealed
that T. gigas haplotypes were clustered into seven clades, suggesting
that they are genetically diverse among populations which derived
from a common ancestor.
Abstract: After the development of the Internet a suitable
discipline for trading goods electronically has been emerged.
However, this type of markets is not still mature enough in order to
become independent and get closer to seller/buyer-s needs.
Furthermore, the buyable and sellable goods in these markets still
don-t have essential standards for being well-defined. In this paper,
we will present a model for development of a market which can
contain goods with variable definitions and we will also investigate
its characteristics. Besides, by noticing the fact that people have
different discriminations, it-s figured out that the significance of each
attribute of a specific product may vary from different people-s view
points. Consequently we-ll present a model for weighting and
accordingly different people-s view points could be satisfied. These
two aspects will be discussed completely throughout this paper.
Abstract: An IEC technique is described for a multi-objective
search of conceptual solutions. The survivability of solutions is
influenced by both model-based fitness and subjective human
preferences. The concepts- preferences are articulated via a hierarchy
of sub-concepts. The suggested method produces an objectivesubjective
front. Academic example is employed to demonstrate the
proposed approach.
Abstract: In this study, the density dependent nonlinear reactiondiffusion
equation, which arises in the insect dispersal models, is
solved using the combined application of differential quadrature
method(DQM) and implicit Euler method. The polynomial based
DQM is used to discretize the spatial derivatives of the problem. The
resulting time-dependent nonlinear system of ordinary differential
equations(ODE-s) is solved by using implicit Euler method. The
computations are carried out for a Cauchy problem defined by a onedimensional
density dependent nonlinear reaction-diffusion equation
which has an exact solution. The DQM solution is found to be in a
very good agreement with the exact solution in terms of maximum
absolute error. The DQM solution exhibits superior accuracy at large
time levels tending to steady-state. Furthermore, using an implicit
method in the solution procedure leads to stable solutions and larger
time steps could be used.
Abstract: Heating systems are a necessity for regions which
brace extreme cold weather throughout the year. To maintain a comfortable temperature inside a given place, heating systems
making use of- Hydronic boilers- are used. The principle of a single
pipe system serves as a base for their working. It is mandatory for these heating systems to control the room temperature, thus
maintaining a warm environment. In this paper, the concept of regulation of the room temperature over a wide range is established
by using an Adaptive Fuzzy Controller (AFC). This fuzzy controller automatically detects the changes in the outside temperatures and
correspondingly maintains the inside temperature to a palatial value. Two separate AFC's are put to use to carry out this function: one to
determine the quantity of heat needed to reach the prospective temperature required and to set the desired temperature; the other to control the position of the valve, which is directly proportional to the
error between the present room temperature and the user desired temperature. The fuzzy logic controls the position of the valve as per
the requirement of the heat. The amount by which the valve opens or closes is controlled by 5 knob positions, which vary from minimum to maximum, thereby regulating the amount of heat flowing through the valve. For the given test system data, different de-fuzzifier
methods have been implemented and the results are compared. In order to validate the effectiveness of the proposed approach, a fuzzy controller has been designed by obtaining a test data from a real time
system. The simulations are performed in MATLAB and are verified with standard system data. The proposed approach can be implemented for real time applications.
Abstract: This paper aims to present a survey of object
recognition/classification methods based on image moments. We
review various types of moments (geometric moments, complex
moments) and moment-based invariants with respect to various
image degradations and distortions (rotation, scaling, affine
transform, image blurring, etc.) which can be used as shape
descriptors for classification. We explain a general theory how to
construct these invariants and show also a few of them in explicit
forms. We review efficient numerical algorithms that can be used
for moment computation and demonstrate practical examples of
using moment invariants in real applications.
Abstract: The effect of phosphorus supplementation of ammoniated rice straw was studied. The in vitro experiment was carried out following the first stage of Tilley and Terry method. The treatments consisting of four diets were A = 50% ammoniated rice straw + 50% concentrate (control), B = A + 0.2% Phosphor (P) supplement, C = A + 0.4% Phosphor (P) supplement, and D = A + 0.6% Phosphor (P) supplement of dry matter. Completely randomized design was used as the experimental design with differences among treatment means were examined using Duncan multiple range test. Variables measured were total bacterial and cellulolytic bacterial population, cellulolytic enzyme activity, ammonia (NH3) and volatile fatty acid (VFA) concentrations, as fermentability indicators and synthesized microbial protein, as well as degradability indicators including dry matter (DM), organic matter (OM), neutral detergent fibre (NDF), acid detergent fibre (ADF) and cellulose. The results indicated that fermentability and degradability of diets consisting ammoniated rice straw with P supplementation were significantly higher than the control diet (P< 0.05). It is concluded that P supplementation is important to improve fermentability and degradability of rations containing ammoniated RS and concentrate. In terms of the most effective level of P supplementation occurred at a supplementation rate of 0.4% of dry matter.