Abstract: High building constructions are increasing in south
beaches of the Caspian Sea because of tourist attractions and limitation of residential areas. According to saturated alluvial fields transfer of load from high structures to the soil by piles is inevitable.
In spite of most of these piles are under compression forces, tension piles are used in special conditions. Few studies have been conducted
because of the limited use of these piles. Tension capacity of openended pipe piles in full scale was tested in this study. The length of the bored piles was 420 up to 480 cm and all were in 120 cm
diameter. The results of testing 7 piles were compared with the results of relations given by researches.
Abstract: In this study, a fuzzy similarity approach for Arabic web pages classification is presented. The approach uses a fuzzy term-category relation by manipulating membership degree for the training data and the degree value for a test web page. Six measures are used and compared in this study. These measures include: Einstein, Algebraic, Hamacher, MinMax, Special case fuzzy and Bounded Difference approaches. These measures are applied and compared using 50 different Arabic web-pages. Einstein measure was gave best performance among the other measures. An analysis of these measures and concluding remarks are drawn in this study.
Abstract: The copper flotation tailings from Konkola Copper
mine in Nchanga, Zambia were used in the study. The purpose of this
study was to determine the leaching characteristics of the tailings
material prior and after the physical beneficiation process is
employed. The Knelson gravity concentrator (KC-MD3) was used for
the beneficiation process. The copper leaching efficiencies and
impurity co-extraction percentages in both the upgraded and the raw
feed material were determined at different pH levels and temperature.
It was observed that the copper extraction increased with an increase
in temperature and a decrease in pH levels. In comparison to the raw
feed sample, the upgraded sample reported a maximum copper
extraction of 69% which was 9%, higher than raw feed % extractions.
The impurity carry over was reduced from 18% to 4 % on the
upgraded sample. The reduction in impurity co-extraction was as a
result of the removal of the reactive gangue elements during the
upgrading process, this minimized the number of side reaction
occurring during leaching.
Abstract: This article investigated the validity of C-test and Cloze test which purport to measure general English proficiency. To provide empirical evidence pertaining to the validity of the interpretations based on the results of these integrative language tests, their criterion-related validity was investigated. In doing so, the test of English as a foreign language (TOEFL) which is an established, standardized, and internationally administered test of general English proficiency was used as the criterion measure. Some 90 Iranian English majors participated in this study. They were seniors studying English at a university in Tehran, Iran. The results of analyses showed that there is a statistically significant correlation among participants- scores on Cloze test, C-test, and the TOEFL. Building on the findings of the study and considering criterion-related validity as the evidential basis of the validity argument, it was cautiously deducted that these tests measure the same underlying trait. However, considering the limitations of using criterion measures to validate tests, no absolute claims can be made as to the construct validity of these integrative tests.
Abstract: The experimental thermal performance of two heat
exchangers in closed-wet cooling tower (CWCT) was investigated in
this study. The test sections are heat exchangers which have multi path
that is used as the entrance of cooling water and are consisting of
bare-type copper tubes between 15.88mm and 19.05mm. The process
fluids are the cooling water that flows from top part of heat exchanger
to bottom side in the inner side of tube, and spray water that flows
gravitational direction in the outer side of it. Air contacts its outer side
of that as it counterflows. Heat and mass transfer coefficients and
cooling capacity were calculated with variations of process fluids,
multi path and different diameter tubes to figure out the performance
of characteristics of CWCT.
The main results were summarized as follows: The results show this
experiment is reliable with values of heat and mass transfer
coefficients comparing to values of correlations. Heat and mass
transfer coefficients and cooling capacity of two paths are higher than
these with one path using 15.88 and 19.05mm tubes. Cooling capacity
per unit volume with 15.88mm tube using one and two paths are
higher than 19.05mm tube due to increase of surface area per unit
volume.
Abstract: This paper reports on the enhanced photoluminescence
(PL) of nanocomposites through the layered structuring of phosphor
and quantum dot (QD). Green phosphor of Sr2SiO4:Eu, red QDs of
CdSe/CdS/CdZnS/ZnS core-multishell, and thermo-curable resin
were used for this study. Two kinds of composite (layered and mixed)
were prepared, and the schemes for optical energy transfer between
QD and phosphor were suggested and investigated based on PL decay
characteristics. It was found that the layered structure is more effective
than the mixed one in the respects of PL intensity, PL decay and
thermal loss. When this layered nanocomposite (QDs on phosphor) is
used to make white light emitting diode (LED), the brightness is
increased by 37 %, and the color rendering index (CRI) value is raised
to 88.4 compared to the mixed case of 80.4.
Abstract: Previous studies on political budget cycles (PBCs)
implicitly assume the executive has full discretion power over fiscal
policy, neglecting the role of checks and balances of the legislature.
This paper goes beyond traditional PBCs models and sheds light on
the case study of Japan, South Korea, and Taiwan over the 1988-2007
periods. Based on the results, we find no evidence of electoral impacts
on the public expenditures in South Korean and Taiwan's
congressional elections. We also noted that PBCs are found on
Taiwan-s government expenditures during our sample periods.
Furthermore, the results also show that Japan-s legislature has a
significant checks and balances on government-s expenditures.
However, empirical results show that the legislature veto player in
Taiwan neither has effect on the reduction of public expenditures, nor
has the moderating effect over Taiwan-s political budget cycles, albeit
that they are statistically insignificant.We suggest that the existence of
PBCs in Taiwan is due to a weaker systemof checks and balances. Our
conjecture is that Taiwan either has no legislative veto player or has
observed low compliance to the law during the time period examined
in our study.
Abstract: This paper presents the prediction of kidney
dysfunction using different neural network (NN) approaches. Self
organization Maps (SOM), Probabilistic Neural Network (PNN) and
Multi Layer Perceptron Neural Network (MLPNN) trained with Back
Propagation Algorithm (BPA) are used in this study. Six hundred and
sixty three sets of analytical laboratory tests have been collected from
one of the private clinical laboratories in Baghdad. For each subject,
Serum urea and Serum creatinin levels have been analyzed and tested
by using clinical laboratory measurements. The collected urea and
cretinine levels are then used as inputs to the three NN models in
which the training process is done by different neural approaches.
SOM which is a class of unsupervised network whereas PNN and
BPNN are considered as class of supervised networks. These
networks are used as a classifier to predict whether kidney is normal
or it will have a dysfunction. The accuracy of prediction, sensitivity
and specificity were found for each type of the proposed networks
.We conclude that PNN gives faster and more accurate prediction of
kidney dysfunction and it works as promising tool for predicting of
routine kidney dysfunction from the clinical laboratory data.
Abstract: In this paper we discuss a set of guidelines which
could be adapted when designing an audio user interface for the
visually impaired. It is based on an audio environment that is
focused on audio positioning. Unlike current applications which only
interpret Graphical User Interface (GUI) for the visually impaired,
this particular audio environment bypasses GUI to provide a direct
auditory output. It presents the capability of two dimensional (2D)
navigation on audio interfaces. This paper highlights the significance
of a 2D audio environment with spatial information in the context
of the visually impaired. A thorough usability study has been conducted
to prove the applicability of proposed design guidelines for
these auditory interfaces. While proving these guidelines, previously
unearthed design aspects have been revealed in this study.
Abstract: The dynamic model of a drill in drilling process was
proposed and investigated in this study. To assure a good drilling quality, the vibration variation on the drill tips during high speed
drilling is needed to be investigated. A pre-twisted beam is used to
simulate the drill. The moving Winkler-Type elastic foundation is used to characterize the tip boundary variation in drilling. Due to the
variation of the drill depth, a time dependent dynamic model for the drill is proposed. Results simulated from this proposed model indicate that an abrupt natural frequencies drop are experienced as the drill tip
tough the workpiece, and a severe vibration is induced. The effects of parameters, e.g. drilling speed, depth, drill size and thrust force on the
drill tip responses studied.
Abstract: For Seismic design, it is important to estimate,
maximum lateral displacement (inelastic displacement) of the
structures due to sever earthquakes for several reasons. Seismic
design provisions estimate the maximum roof and storey drifts
occurring in major earthquakes by amplifying the drifts of the
structures obtained by elastic analysis subjected to seismic design
load, with a coefficient named “displacement amplification factor"
which is greater than one. Here, this coefficient depends on various
parameters, such as ductility and overstrength factors. The present
research aims to evaluate the value of the displacement amplification
factor in seismic design codes and then tries to propose a value to
estimate the maximum lateral structural displacement from sever
earthquakes, without using non-linear analysis. In seismic codes,
since the displacement amplification is related to “force reduction
factor" hence; this aspect has been accepted in the current study.
Meanwhile, two methodologies are applied to evaluate the value of
displacement amplification factor and its relation with the force
reduction factor. In the first methodology, which is applied for all
structures, the ratio of displacement amplification and force reduction
factors is determined directly. Whereas, in the second methodology
that is applicable just for R/C moment resisting frame, the ratio is
obtained by calculating both factors, separately. The acquired results
of these methodologies are alike and estimate the ratio of two factors
from 1 to 1.2. The results indicate that the ratio of the displacement
amplification factor and the force reduction factor differs to those
proposed by seismic provisions such as NEHRP, IBC and Iranian
seismic code (standard no. 2800).
Abstract: The introduction of mass-customization has enabled
new ways to treat patients within medicine. However, the
introduction of industrialized treatments has also meant new
obstacles. The purpose of this study was to introduce and
theoretically test a method for improving dental crown fit. The
optimization method allocates support points in order to check the
final variation for dental crowns. Three different types of geometries
were tested and compared. The three geometries were also divided
into three sub-geometries: Current method, Optimized method and
Feasible method. The Optimized method, using the whole surface for
support points, provided the best results. The results support the
objective of the study. It also seems that the support optimization
method can dramatically improve the robustness of dental crown
treatments.
Abstract: Poly-β-hydroxybutyrate (PHB) is one of the most
famous biopolymers that has various applications in production of
biodegradable carriers. The most important strategy for enhancing
efficiency in production process and reducing the price of PHB, is the
accurate expression of kinetic model of products formation and
parameters that are effective on it, such as Dry Cell Weight (DCW)
and substrate consumption. Considering the high capabilities of
artificial neural networks in modeling and simulation of non-linear
systems such as biological and chemical industries that mainly are
multivariable systems, kinetic modeling of microbial production of
PHB that is a complex and non-linear biological process, the three
layers perceptron neural network model was used in this study.
Artificial neural network educates itself and finds the hidden laws
behind the data with mapping based on experimental data, of dry cell
weight, substrate concentration as input and PHB concentration as
output. For training the network, a series of experimental data for
PHB production from Hydrogenophaga Pseudoflava by glucose
carbon source was used. After training the network, two other
experimental data sets that have not intervened in the network
education, including dry cell concentration and substrate
concentration were applied as inputs to the network, and PHB
concentration was predicted by the network. Comparison of predicted
data by network and experimental data, indicated a high precision
predicted for both fructose and whey carbon sources. Also in present
study for better understanding of the ability of neural network in
modeling of biological processes, microbial production kinetic of
PHB by Leudeking-Piret experimental equation was modeled. The
Observed result indicated an accurate prediction of PHB
concentration by artificial neural network higher than Leudeking-
Piret model.
Abstract: This paper describes the design process and the realtime validation of an innovative autonomous mid-air flight and landing system developed by the Italian Aerospace Research Center in the framework of the Italian national funded project TECVOL (Technologies for the Autonomous Flight). In the paper it is provided an insight of the whole development process of the system under study. In particular, the project framework is illustrated at first, then the functional context and the adopted design and testing approach are described, and finally the on-ground validation test rig on purpose designed is addressed in details. Furthermore, the hardwarein- the-loop validation of the autonomous mid-air flight and landing system by means of the real-time test rig is described and discussed.
Abstract: Computer network courses are essential parts of college computer science curriculum and hands-on networking experience is well recognized as an effective approach to help students understand better about the network concepts, the layered architecture of network protocols, and the dynamics of the networks. However, existing networking labs are usually server-based and relatively cumbersome, which require a certain level of specialty and resource to set up and maintain the lab environment. Many universities/colleges lack the resources and build-ups in this field and have difficulty to provide students with hands-on practice labs. A new affordable and easily-adoptable approach to networking labs is desirable to enhance network teaching and learning. In addition, current network labs are short on providing hands-on practice for modern wireless and mobile network learning. With the prevalence of smart mobile devices, wireless and mobile network are permeating into various aspects of our information society. The emerging and modern mobile technology provides computer science students with more authentic learning experience opportunities especially in network learning. A mobile device based hands-on labware can provide an excellent ‘real world’ authentic learning environment for computer network especially for wireless network study. In this paper, we present our mobile device-based hands-on labware (series of lab module) for computer network learning which is guided by authentic learning principles to immerse students in a real world relevant learning environment. We have been using this labware in teaching computer network, mobile security, and wireless network classes. The student feedback shows that students can learn more when they have hands-on authentic learning experience.
Abstract: This study is a descriptive-normative research. It
attempted to investigate the restaurants’ firm performance in terms of
the customers and restaurant personnel’s degree of satisfaction. A
total of 12 restaurants in Bangkok, Thailand that offer Thai cuisine
were included in this study. It involved 24 stockholders/managers,
120 subordinates and 360 customers. General Managers and
restaurants’ stockholders, 10 staffs, and 30 costumers for each
restaurant were chosen for random sampling. This study found that
respondents are slightly satisfied with their work environment but are
generally satisfied with the accessibility to transportation, to malls,
convenience, safety, recreation, noise-free, and attraction; customers
find the Quality of Food in most Thai Cuisines like services, prices of
food, sales promotion, and capital and length of service satisfactory.
Therefore, both stockholder-related and personnel-related factors
which are influenced by restaurant, personnel, and customer-related
factors are partially accepted whereas; customer-related factors which
are influenced by restaurant, personnel and customer-related factors
are rejected.
Abstract: Relevant agricultural information disseminator
(extension agent) ratio of 1:3500 farm families which become a
menace to agricultural production capacity in developing countries
necessitate this study. Out of 4 zones in the state, 24 extension agents
in each zone, 4 extension agents using cell phones and 120 farmers
using cell phone and 120 other farmers not using cell phone were
purposively selected to give 240 farmers that participated in the
research. Data were collected using interview guide and analysized
using frequency, percentage and t-test.. Frequency of contact with
agricultural information centers revealed that cell phone user farmers
had greater means score of X 41.43 contact as against the low mean
X19.32 contact recorded by farmers receiving agricultural
information from extension agents not using cell phone and their
production was statistically significant at P < 0.05. Usage of cell
phone increase extension agent contact and increase farmers-
production capacity.
Abstract: Transpedicular screw fixation in spinal fractures,
degenerative changes, or deformities is a well-established procedure.
However, important rate of fixation failure due to screw bending,
loosening, or pullout are still reported particularly in weak bone stock
in osteoporosis. To overcome the problem, mechanism of failure has
to be fully investigated in vitro. Post-mortem human subjects are less
accessible and animal cadavers comprise limitations due to different
geometry and mechanical properties. Therefore, the development of a
synthetic model mimicking the realistic human vertebra is highly
demanded. A bone surrogate, composed of Polyurethane (PU) foam
analogous to cancellous bone porous structure, was tested for 3
different densities in this study. The mechanical properties were
investigated under uniaxial compression test by minimizing the end
artifacts on specimens. The results indicated that PU foam of 0.32
g.cm-3 density has comparable mechanical properties to human
cancellous bone in terms of young-s modulus and yield strength.
Therefore, the obtained information can be considered as primary
step for developing a realistic cancellous bone of human vertebral
body. Further evaluations are also recommended for other density
groups.
Abstract: Cu-mesoporous TiO2 is developed for removal acid
odor cooperated with ozone assistance and online- regeneration
system with/without UV irradiation (all weather) in study. The results
showed that Cu-mesoporous TiO2 present the desirable adsorption
efficiency of acid odor without UV irradiation, due to the larger
surface area, pore sizeand the additional absorption ability provided by
Cu. In the photocatalysis process, the material structure also benefits
Cu-mesoporous TiO2 to perform the more outstanding efficiency on
degrading acid odor. Cu also postponed the recombination of
electron-hole pairs excited from TiO2 to enhance photodegradation
ability. Cu-mesoporous TiO2 could gain the conspicuous increase on
photocatalysis ability from ozone assistance, but without any benefit
on adsorption. In addition, the online regeneration procedure could
process the used Cu-mesoporous TiO2 to reinstate the adsorption
ability and maintain the photodegradtion performance, depended on
scrubbing, desorping acid odor and reducing Cu to metal state.
Abstract: wind catchers have been served as a cooling system, used to provide acceptable ventilation by means of renewable energy of wind. In the present study, the city of Yazd in arid climate is selected as case study. From the architecture point of view, learning about wind catchers in this study is done by means of field surveys. Research method for selection of the case is based on random form, and analytical method. Wind catcher typology and knowledge of relationship governing the wind catcher's architecture were those measures that are taken for the first time. 53 wind catchers were analyzed. The typology of the wind-catchers is done by the physical analyzing, patterns and common concepts as incorporated in them. How the architecture of wind catcher can influence their operations by analyzing thermal behavior are the archetypes of selected wind catchers. Calculating fluids dynamics science, fluent software and numerical analysis are used in this study as the most accurate analytical approach. The results obtained from these analyses show the formal specifications of wind catchers with optimum operation in Yazd. The knowledge obtained from the optimum model could be used for design and construction of wind catchers with more improved operation