Abstract: Within dental-guided surgery, there has been a lack
of analytical methods for optimizing the treatment of the
rehabilitation concepts regarding geometrical variation. The purpose
of this study is to find the source of the greatest geometrical variation
contributor and sensitivity contributor with the help of virtual
variation simulation of a dental drill- and implant-guided surgery
process using a methodical approach. It is believed that lower
geometrical variation will lead to better patient security and higher
quality of dental drill- and implant-guided surgeries. It was found
that the origin of the greatest contributor to the most variation, and
hence where the foci should be set, in order to minimize geometrical
variation was in the assembly category (surgery). This was also the
category that was the most sensitive for geometrical variation.
Abstract: Quality evaluation of urban environment is an integral
part of efficient urban environment planning and management. The
development of fuzzy set theory (FST) and the introduction of FST
to the urban study field attempts to incorporate the gradual variation
and avoid loss of information. Urban environmental quality
assessment pertain to interpretation and forecast of the urban
environmental quality according to the national regulation about the
permitted content of contamination for the sake of protecting human
health and subsistence environment . A strategic motor vehicle
control strategy has to be proposed to mitigate the air pollution in the
city. There is no well defined guideline for the assessment of urban
air pollution and no systematic study has been reported so far for
Indian cities. The methodology adopted may be useful in similar
cities of India. Remote sensing & GIS can play significant role in
mapping air pollution.
Abstract: Near-infrared (NIR) spectroscopy is a widely used
method for material identification for laboratory and industrial applications.
While standard spectrometers only allow measurements at
one sampling point at a time, NIR Spectral Imaging techniques can
measure, in real-time, both the size and shape of an object as well as
identify the material the object is made of. The online classification
and sorting of recovered paper with NIR Spectral Imaging (SI)
is used with success in the paper recycling industry throughout
Europe. Recently, the globalisation of the recycling material streams
caused that water-based flexographic-printed newspapers mainly from
UK and Italy appear also in central Europe. These flexo-printed
newspapers are not sufficiently de-inkable with the standard de-inking
process originally developed for offset-printed paper. This de-inking
process removes the ink from recovered paper and is the fundamental
processing step to produce high-quality paper from recovered paper.
Thus, the flexo-printed newspapers are a growing problem for the
recycling industry as they reduce the quality of the produced paper
if their amount exceeds a certain limit within the recovered paper
material.
This paper presents the results of a research project for the
development of an automated entry inspection system for recovered
paper that was jointly conducted by CTR AG (Austria) and PTS
Papiertechnische Stiftung (Germany). Within the project an NIR
SI prototype for the identification of flexo-printed newspaper has
been developed. The prototype can identify and sort out flexoprinted
newspapers in real-time and achieves a detection accuracy
for flexo-printed newspaper of over 95%. NIR SI, the technology the
prototype is based on, allows the development of inspection systems
for incoming goods in a paper production facility as well as industrial
sorting systems for recovered paper in the recycling industry in the
near future.
Abstract: In this paper we propose a class of second derivative multistep methods for solving some well-known classes of Lane- Emden type equations which are nonlinear ordinary differential equations on the semi-infinite domain. These methods, which have good stability and accuracy properties, are useful in deal with stiff ODEs. We show superiority of these methods by applying them on the some famous Lane-Emden type equations.
Abstract: Short message integrated distributed monitoring systems (SM-DMS) are growing rapidly in wireless communication applications in various areas, such as electromagnetic field (EMF) management, wastewater monitoring, and air pollution supervision, etc. However, delay in short messages often makes the data embedded in SM-DMS transmit unreliably. Moreover, there are few regulations dealing with this problem in SMS transmission protocols. In this study, based on the analysis of the command and data requirements in the SM-DMS, we developed a processing model for the control center to solve the delay problem in data transmission. Three components of the model: the data transmission protocol, the receiving buffer pool method, and the timer mechanism were described in detail. Discussions on adjusting the threshold parameter in the timer mechanism were presented for the adaptive performance during the runtime of the SM-DMS. This model optimized the data transmission reliability in SM-DMS, and provided a supplement to the data transmission reliability protocols at the application level.
Abstract: Many electronic voting systems, classified mainly as homomorphic cryptography based, mix-net based and blind signature based, appear after the eighties when zero knowledge proofs were introduced. The common ground for all these three systems is that none of them works without real time cryptologic calculations that should be held on a server. As far as known, the agent-based approach has not been used in a secure electronic voting system. In this study, an agent-based electronic voting schema, which does not contain real time calculations on the server side, is proposed. Conventional cryptologic methods are used in the proposed schema and some of the requirements of an electronic voting system are constructed within the schema. The schema seems quite secure if the used cryptologic methods and agents are secure. In this paper, proposed schema will be explained and compared with already known electronic voting systems.
Abstract: Self-organizing map (SOM) is a well known data reduction technique used in data mining. Data visualization can reveal structure in data sets that is otherwise hard to detect from raw data alone. However, interpretation through visual inspection is prone to errors and can be very tedious. There are several techniques for the automatic detection of clusters of code vectors found by SOMs, but they generally do not take into account the distribution of code vectors; this may lead to unsatisfactory clustering and poor definition of cluster boundaries, particularly where the density of data points is low. In this paper, we propose the use of a generic particle swarm optimization (PSO) algorithm for finding cluster boundaries directly from the code vectors obtained from SOMs. The application of our method to unlabeled call data for a mobile phone operator demonstrates its feasibility. PSO algorithm utilizes U-matrix of SOMs to determine cluster boundaries; the results of this novel automatic method correspond well to boundary detection through visual inspection of code vectors and k-means algorithm.
Abstract: This paper presents an efficient algorithm for
optimization of radial distribution systems by a network
reconfiguration to balance feeder loads and eliminate overload
conditions. The system load-balancing index is used to determine the
loading conditions of the system and maximum system loading
capacity. The index value has to be minimum in the optimal network
reconfiguration of load balancing. A method based on Tabu search
algorithm, The Tabu search algorithm is employed to search for the
optimal network reconfiguration. The basic idea behind the search is
a move from a current solution to its neighborhood by effectively
utilizing a memory to provide an efficient search for optimality. It
presents low computational effort and is able to find good quality
configurations. Simulation results for a radial 69-bus system with
distributed generations and capacitors placement. The study results
show that the optimal on/off patterns of the switches can be identified
to give the best network reconfiguration involving balancing of
feeder loads while respecting all the constraints.
Abstract: A new estimator for evolutionary spectrum (ES) based
on short time Fourier transform (STFT) and modified group delay
function (MGDF) by signal decomposition (SD) is proposed. The
STFT due to its built-in averaging, suppresses the cross terms and the
MGDF preserves the frequency resolution of the rectangular window
with the reduction in the Gibbs ripple. The present work overcomes
the magnitude distortion observed in multi-component non-stationary
signals with STFT and MGDF estimation of ES using SD. The SD is
achieved either through discrete cosine transform based harmonic
wavelet transform (DCTHWT) or perfect reconstruction filter banks
(PRFB). The MGDF also improves the signal to noise ratio by
removing associated noise. The performance of the present method is
illustrated for cross chirp and frequency shift keying (FSK) signals,
which indicates that its performance is better than STFT-MGDF
(STFT-GD) alone. Further its noise immunity is better than STFT.
The SD based methods, however cannot bring out the frequency
transition path from band to band clearly, as there will be gap in the
contour plot at the transition. The PRFB based STFT-SD shows good
performance than DCTHWT decomposition method for STFT-GD.
Abstract: This paper presents the results of corrosion fatigue
crack growth behaviour of a Ni-Cr-Mn steel commonly used in
marine applications. The effect of mechanical variables such as
frequency and load ratio on fatigue crack growth rate at various
stages has been studied using compact tension (C(T)) specimens
along the rolling direction of steel plate under 3.5% saturated NaCl
aqueous environment. The significance of crack closure on corrosion
fatigue, and the validity of Elber-s empirical linear crack closure
model with the ASTM compliance offset method have been
examined.
Fatigue crack growth rate is higher and threshold stress intensities
are lower in aqueous environment compared to the lab air conditions.
It is also observed that the crack growth rate increases at lower
frequencies. The higher stress ratio promotes the crack growth. The
effect of oxidization and corrosion pit formation is very less as the
stress ratio is increased. It is observed that as stress ratios are
increased, the Elber-s crack closure model agrees well with the crack
closure estimated by the ASTM compliance offset method for tests
conducted at 5Hz frequency compared to tests conducted at 1Hz in
corrosive environment.
Abstract: The optimization and control problem for 4D trajectories
is a subject rarely addressed in literature. In the 4D navigation
problem we define waypoints, for each mission, where the arrival
time is specified in each of them. One way to design trajectories for
achieving this kind of mission is to use the trajectory optimization
concepts. To solve a trajectory optimization problem we can use
the indirect or direct methods. The indirect methods are based on
maximum principle of Pontryagin, on the other hand, in the direct
methods it is necessary to transform into a nonlinear programming
problem. We propose an approach based on direct methods with a
pseudospectral integration scheme built on Chebyshev polynomials.
Abstract: Laboratory experiments have been performed to investigate photocatalytic detoxification by using TiO2 photocatalyst for treating dairy effluent. Various operational parameters such as catalyst concentration, initial concentration, angle of tilt of solar flat plate reactor and flow rate were investigated. Results indicated that the photocatalytic detoxification process can efficiently treat dairy effluent. Experimental runs with dairy wastewater can be used to identify the optimum operational parameters to perform wastewater degradation on large scale for recycling purpose. Also effect of two different types of reactors on degradation process was analyzed.
Abstract: Flow around a flat tube is studied numerically. Reynolds number is defined base on equivalent circular tube and it is varied in range of 100 to 300. Equations are solved by using finite volume method and results are presented in form of drag and lift coefficient. Results show that drag coefficient of flat tube is up to 66% lower than circular tube with equivalent diameter. In addition, by increasing l/D from 1 to 2, the drag coefficient of flat tube is decreased about 14-27%.
Abstract: To improve the efficiency of parametric studies or
tests planning the method is proposed, that takes into account all input parameters, but only a few simulation runs are performed to
assess the relative importance of each input parameter. For K input
parameters with N input values the total number of possible combinations of input values equals NK. To limit the number of runs,
only some (totally N) of possible combinations are taken into account. The sampling procedure Updated Latin Hypercube
Sampling is used to choose the optimal combinations. To measure the
relative importance of each input parameter, the Spearman rank
correlation coefficient is proposed. The sensitivity and the influence
of all parameters are analyzed within one procedure and the key
parameters with the largest influence are immediately identified.
Abstract: An approach of design of stable of control systems with ultimately wide ranges of uncertainly disturbed parameters is offered. The method relies on using of nonlinear structurally stable functions from catastrophe theory as controllers. Theoretical part presents an analysis of designed nonlinear second-order control systems. As more important the integrators in series, canonical controllable form and Jordan forms are considered. The analysis resumes that due to added controllers systems become stable and insensitive to any disturbance of parameters. Experimental part presents MATLAB simulation of design of control systems of epidemic spread, aircrafts angular motion and submarine depth. The results of simulation confirm the efficiency of offered method of design. KeywordsCatastrophes, robust control, simulation, uncertain parameters.
Abstract: A numerical simulation of vortex-induced vibration of
a 2-dimensional elastic circular cylinder with two degree of freedom
under the uniform flow is calculated when Reynolds is 200.
2-dimensional incompressible Navier-Stokes equations are solved
with the space-time finite element method, the equation of the cylinder
motion is solved with the new explicit integral method and the mesh
renew is achieved by the spring moving mesh technology. Considering
vortex-induced vibration with the low reduced damping parameter, the
variety trends of the lift coefficient, the drag coefficient, the
displacement of cylinder are analyzed under different oscillating
frequencies of cylinder. The phenomena of locked-in, beat and
phases-witch were captured successfully. The evolution of vortex
shedding from the cylinder with time is discussed. There are very
similar trends in characteristics between the results of the one degree
of freedom cylinder model and that of the two degree of freedom
cylinder model. The streamwise vibrations have a certain effect on the
lateral vibrations and their characteristics.
Abstract: Numerical integration of initial boundary problem for advection equation in 3 ℜ is considered. The method used is
conditionally stable semi-Lagrangian advection scheme with high order interpolation on unstructured mesh. In order to increase time step integration the BFECC method with limiter TVD correction is used. The method is adopted on parallel graphic processor unit environment using NVIDIA CUDA and applied in Navier-Stokes solver. It is shown that the calculation on NVIDIA GeForce 8800
GPU is 184 times faster than on one processor AMDX2 4800+ CPU. The method is extended to the incompressible fluid dynamics solver. Flow over a Cylinder for 3D case is compared to the experimental data.
Abstract: Segmentation of a color image composed of different
kinds of regions can be a hard problem, namely to compute for an
exact texture fields. The decision of the optimum number of
segmentation areas in an image when it contains similar and/or un
stationary texture fields. A novel neighborhood-based segmentation
approach is proposed. A genetic algorithm is used in the proposed
segment-pass optimization process. In this pass, an energy function,
which is defined based on Markov Random Fields, is minimized. In
this paper we use an adaptive threshold estimation method for image
thresholding in the wavelet domain based on the generalized
Gaussian distribution (GGD) modeling of sub band coefficients. This
method called Normal Shrink is computationally more efficient and
adaptive because the parameters required for estimating the threshold
depend on sub band data energy that used in the pre-stage of
segmentation. A quad tree is employed to implement the multi
resolution framework, which enables the use of different strategies at
different resolution levels, and hence, the computation can be
accelerated. The experimental results using the proposed
segmentation approach are very encouraging.
Abstract: increased competition and increased costs of
designing made it important for the firms to identify the right
products and the right methods for manufacturing the products. Firms
should focus on customers and identify customer demands directly to
design the right products. Several management methods and
techniques that are currently available improve one or more functions
or processes in an industry and do not take the complete product life
cycle into consideration. On the other hand target costing is a method
/ philosophy that takes financial, manufacturing and customer aspects
into consideration during designing phase and helps firms in making
product design decisions to increase the profit / value of the
company. It uses various techniques to identify customer demands, to
decrease costs of manufacturing and finally to achieve strategic goals.
Target Costing forms an integral part of total product design /
redesign based on strategic plans.
Abstract: In this note, we consider a family of iterative formula for computing the weighted Minskowski inverses AM,N in Minskowski space, and give two kinds of iterations and the necessary and sufficient conditions of the convergence of iterations.