Abstract: Comparing other methods of waste water treatment,
constructed wetlands are one of the most fascinating practices
because being a natural process they are eco-friendly have low
construction and maintenance cost and have considerable capability
of wastewater treatment. The current research was focused mainly on
comparison of Ranunculus muricatus and Typha latifolia as wetland
plants for domestic wastewater treatment by designing and
constructing efficient pilot scale horizontal subsurface flow
mesocosms. Parameters like chemical oxygen demand, biological
oxygen demand, phosphates, sulphates, nitrites, nitrates, and
pathogenic indicator microbes were studied continuously with
successive treatments. Treatment efficiency of the system increases
with passage of time and with increase in temperature. Efficiency of
T. latifolia planted setups in open environment was fairly good for
parameters like COD and BOD5 which was showing reduction up to
82.5% for COD and 82.6% for BOD5 while DO was increased up to
125%. Efficiency of R. muricatus vegetated setup was also good but
lowers than that of T. latifolia planted showing 80.95% removal of
COD and BOD5. Ranunculus muricatus was found effective in
reducing bacterial count in wastewater. Both macrophytes were
found promising in wastewater treatment.
Abstract: Cemented carbide balls are usually implemented in
industry under the environment of high speed, high temperature,
corrosiveness and strong collisions. However, its application is limited
due to high fabrication cost, processing efficiency and quality. A novel
eccentric lapping method with two rotatable lapping plates was
proposed in this paper. A mathematical model was constructed to
analyze the influence of each design parameter on this lapping method.
To validate this new lapping method, an orthogonal experiment was
conducted with cemented carbide balls (YG6). The simulation model
was verified and the optimal lapping parameters were derived. The
results show that the surface roundness of the balls reaches to 0.65um
from 2um in 1 hour using this lapping method. So, using this novel
lapping method, it can effectively improve the machining precision
and efficiency of cemented carbide balls.
Abstract: Knowledge is considered as an important asset which
can help organizations to create competitive advantage. The necessity
of taking care of these assets is more important in these days – in
days of turbulent changes in business environment. Knowledge could
facilitate adaption to constant changes. The aim of this paper is to
describe how the knowledge sharing can be supported in the
manufacturing companies. The methods of case studies and grounded
theory were used to present information gained by carrying out semistructured
interviews. Results show that knowledge sharing is
supported in very similar ways in respondent companies.
Abstract: Attributes and methods are the basic contents of an
object-oriented class. The connectivity among these class members
and the relationship between the class and other classes play an
important role in determining the quality of an object-oriented
system. Class cohesion evaluates the degree of relatedness of class
attributes and methods, whereas class coupling refers to the degree to
which a class is related to other classes. Researchers have proposed
several class cohesion and class coupling measures. However, the
correlation between class coupling and class cohesion measures has
not been thoroughly studied. In this paper, using classes of three
open-source Java systems, we empirically investigate the correlation
between several measures of connectivity-based class cohesion and
coupling. Four connectivity-based cohesion measures and eight
coupling measures are considered in the empirical study. The
empirical study results show that class connectivity-based cohesion
and coupling internal quality attributes are inversely correlated. The
strength of the correlation depends highly on the cohesion and
coupling measurement approaches.
Abstract: This paper shows an experimental testing of a small
unit for combustion of solid fuels, such as charcoal and wood logs,
that can provide electricity. One of the concepts is that the unit does
not require qualified personnel for its operation. The unit itself is
composed of two main parts. The design requires a heat producing
stove and electricity producing thermoelectric generator. After the
construction the unit was tested and the results show that the
emission release is within the legislative requirements for emission
production and environmental protection. That qualifies such unit for
indoor application.
Abstract: Thin-walled elements with a matrix set on a base of
high-valuable Portland cement with dispersed reinforcement from
alkali-resistant glass fibres are used in a range of applications as
claddings of buildings and infrastructure constructions as well as
various architectural elements of residential buildings.
Even though their elementary thickness and therefore total weight
is quite low, architects and building companies demand on even
further decreasing of the bulk density of these fibre-cement elements
for the reason of loading elimination of connected superstructures
and easier assembling in demand conditions.
By the means of various kinds of light-weight aggregates it is
possible to achieve light-weighing of these composite elements.
From the range of possible fillers with different material properties
granulated expanded glass worked the best.
By the means of laboratory testing an effect of two fillers based on
expanded glass on the fibre reinforced cement composite was
verified.
Practical applicability was tested in the production of commonly
manufactured glass fibre reinforced concrete elements, such as
channels for electrical cable deposition, products for urban equipment
and especially various cladding elements.
Even though these are not structural elements, it is necessary to
evaluate also strength characteristics and resistance to environment
for their durability in certain applications.
Abstract: Bir El Djir is an important coastal township in Oran
department, located at 450 Km far away from Algiers on northwest of
Algeria. In this coastal area, the urban sprawl is one of the main
problems that reduce the limited highly fertile land. So, using the
remote sensing and GIS technologies have shown their great
capabilities to solve many earth resources issues.
The aim of this study is to produce land use and cover map for the
studied area at varied periods to monitor possible changes that may
occurred, particularly in the urban areas and subsequently predict
likely changes. For this, two spatial images SPOT and Landsat
satellites from 1987 and 2014 respectively were used to assess the
changes of urban expansion and encroachment during this period
with photo-interpretation and GIS approach.
The results revealed that the town of Bir El Djir has shown a
highest growth rate in the period 1987-2014 which is 1201.5 hectares
in terms of area. These expansions largely concern the new real estate
constructions falling within the social and promotional housing
programs launched by the government.
The most urban expansion is characterized by the new
construction in the form of spontaneous or peripheral precarious
habitat, but also unstructured slums settled especially in the
southeastern part of town.
Abstract: Nowadays, huge amount of multimedia repositories
make the browsing, retrieval and delivery of video contents very slow
and even difficult tasks. Video summarization has been proposed to
improve faster browsing of large video collections and more efficient
content indexing and access. In this paper, we focus on approaches to
video summarization. The video summaries can be generated in many
different forms. However, two fundamentals ways to generate
summaries are static and dynamic. We present different techniques
for each mode in the literature and describe some features used for
generating video summaries. We conclude with perspective for
further research.
Abstract: This article focuses on the issue of airport emergency
plans, which are documents describing reactions to events with
impact on aviation safety or aviation security. The article specifically
focuses on the use and creation of emergency plans, where could be
found a number of disagreements between different stakeholders, for
which the airport emergency plan applies. Those are the friction
surfaces of interfaces, which is necessary to identify and ensure them
smooth process to avoid dangerous situations or delay.
Abstract: Offering a Product-Service System (PSS) is a
well-accepted strategy that companies may adopt to provide a set of
systemic solutions to customers. PSSs were initially provided in a
simple form but now take diversified and complex forms involving
multiple services, products and technologies. With the growing
interest in the PSS, frameworks for the PSS development have been
introduced by many researchers. However, most of the existing
frameworks fail to examine various relations existing in a complex
PSS. Since designing a complex PSS involves full integration of
multiple products and services, it is essential to identify not only
product-service relations but also product-product/ service-service
relations. It is also equally important to specify how they are related
for better understanding of the system. Moreover, as customers tend to
view their purchase from a more holistic perspective, a PSS should be
developed based on the whole system’s requirements, rather than
focusing only on the product requirements or service requirements.
Thus, we propose a framework to develop a complex PSS that is
coordinated fully with the requirements of both worlds. Specifically,
our approach adopts a multi-domain matrix (MDM). A MDM
identifies not only inter-domain relations but also intra-domain
relations so that it helps to design a PSS that includes highly desired
and closely related core functions/ features. Also, various dependency
types and rating schemes proposed in our approach would help the
integration process.
Abstract: Despite the highly touted benefits, emerging
technologies have unleashed pervasive concerns regarding unintended
and unforeseen social impacts. Thus, those wishing to create safe and
socially acceptable products need to identify such side effects and
mitigate them prior to the market proliferation. Various methodologies
in the field of technology assessment (TA), namely Delphi, impact
assessment, and scenario planning, have been widely incorporated in
such a circumstance. However, literatures face a major limitation in
terms of sole reliance on participatory workshop activities. They
unfortunately missed out the availability of a massive untapped data
source of futuristic information flooding through the Internet. This
research thus seeks to gain insights into utilization of futuristic data,
future-oriented documents from the Internet, as a supplementary
method to generate social impact scenarios whilst capturing
perspectives of experts from a wide variety of disciplines. To this end,
network analysis is conducted based on the social keywords extracted
from the futuristic documents by text mining, which is then used as a
guide to produce a comprehensive set of detailed scenarios. Our
proposed approach facilitates harmonized depictions of possible
hazardous consequences of emerging technologies and thereby makes
decision makers more aware of, and responsive to, broad qualitative
uncertainties.
Abstract: One of the best examples, in evolution of the public
procurement, from post-soviet countries are reforms carried out in
Georgia, which brought them close to international standards of
procurement. In Georgia, public procurement legislation started
functioning short after gaining independence. The reform has passed
several stages and came in the form as it is today. It should also be
noted, that countries with economy in transition, including Georgia,
implemented all the reforms in public procurement based on
recommendations and support of World Bank, the United Nations
and other international organizations.
The aim of first adopted law was regulation of the procurement
process of budget-organizations, transparency and creation of
competitive environment for private companies to access state funds
legally. The priorities were identified quite clearly in the wording of
the law, but operation/function of this law could not be reached on its
level, because of some objective and subjective reasons. The high
level of corruption in all levels of governance can be considered as a
main obstacle reason and of course, it is natural, that it had direct
impact on the procurement process, as well as on transparency and
rational use of state funds. These circumstances were the reasons that
reforms in this sphere continued, to improve procurement process, in
particular, the first wave of reforms began after several years. Public
procurement agency carried out reform with World Bank with main
purpose of smartening the procurement legislation and its
harmonization with international treaties and agreements. Also with
the support of World Bank various activities were carried out to raise
awareness of participants involved in procurement system.
Further major changes in the legislation were filed bit later, which
was also directed towards the improvement and smarten of the
procurement process. The third wave of the reform more or less
guaranteed the transparency of the procurement process, which later
became the basis for the rational spending of state funds. The reform
of the procurement system completely changed the procedures.
Carried out reform in Georgia resulted in introducing new
electronic tendering system, which benefit the transparency of the
process, after this became the basis for the further development of a
competitive environment, which become a prerequisite for the state
rational spending. Increased number of supplier organizations
participating in the procurement process resulted in reduction of the
estimated cost and the actual cost.
Assessment of the reforms in Georgia in the field of public
procurement can be concluded, that proper regulation of the sector
and relevant policy may proceed to rational and transparent spending
of the budget from country’s state institutions. Also, the business
sector has the opportunity to work in competitive market conditions
and to make a preliminary analysis, which is a prerequisite for future
strategy and development.
Abstract: Pulmonary Function Tests are important non-invasive
diagnostic tests to assess respiratory impairments and provides
quantifiable measures of lung function. Spirometry is the most
frequently used measure of lung function and plays an essential role
in the diagnosis and management of pulmonary diseases. However,
the test requires considerable patient effort and cooperation,
markedly related to the age of patients resulting in incomplete data
sets. This paper presents, a nonlinear model built using Multivariate
adaptive regression splines and Random forest regression model to
predict the missing spirometric features. Random forest based feature
selection is used to enhance both the generalization capability and the
model interpretability. In the present study, flow-volume data are
recorded for N= 198 subjects. The ranked order of feature importance
index calculated by the random forests model shows that the
spirometric features FVC, FEF25, PEF, FEF25-75, FEF50 and the
demographic parameter height are the important descriptors. A
comparison of performance assessment of both models prove that, the
prediction ability of MARS with the `top two ranked features namely
the FVC and FEF25 is higher, yielding a model fit of R2= 0.96 and
R2= 0.99 for normal and abnormal subjects. The Root Mean Square
Error analysis of the RF model and the MARS model also shows that
the latter is capable of predicting the missing values of FEV1 with a
notably lower error value of 0.0191 (normal subjects) and 0.0106
(abnormal subjects) with the aforementioned input features. It is
concluded that combining feature selection with a prediction model
provides a minimum subset of predominant features to train the
model, as well as yielding better prediction performance. This
analysis can assist clinicians with a intelligence support system in the
medical diagnosis and improvement of clinical care.
Abstract: In the framework of the modernization of the city of
Constantine and in order to restore its status as a regional metropolis
introducing it into the network of cities international metropolises,
has major urban project was launched: project of modernization and
of metropolitanization of the city of Constantine.
Our research project focuses on the management of the project for
the modernization of the city of Constantine (PMMC) focusing on
the management of some aspects of the urban project whose
participation, with the objective assessment of the managerial
approach business.
In this contribution, we focus on two cases revealing taken into
account in our research work on the question of participation of
actors and their organizations. It is "the urban project of
modernization of Constantine" and the operation relating to "the
urban improvement in the city of the Brothers FERRAD in the
district of Zouaghi". This project and this operation with the objective
of improving the living conditions of citizens have faced several
challenges and obstacles that have been in major part the factors of its
failures.
Through this study, we examined the management process and the
mode of organization of the actors of the project as well as the level
of participation of the citizen to finally proposed managerial solutions
toconflict situations observed.
Abstract: Hurling a successful Construction and Demolition
Waste (C&DW) recycling operation around the globe is a challenge
today, predominantly because secondary materials markets are yet to
be integrated. Reducing, Reusing and recycling of (C&DW) have
been employed over the years, and various techniques have been
investigated. However, the economic and environmental viability of
its application seems limited. This paper discusses the costs and
benefits in using secondary materials and focus on investigating reuse
and recycling process for five major types of construction materials:
concrete, metal, wood, cardboard/paper and plasterboard. Data
obtained from demolition specialists and contractors are considered
and evaluated. The research paper found that construction material
recovery process fully incorporate a 3R’s principle contributing to
saving energy and natural resources. This scrutiny leads to the
empathy of grand challenges in construction material recovery
process. Recommendations to deepen material recovery process are
also discussed.
Abstract: This work deals with parameter identification of
permanent magnet motors, a class of ac motor which is particularly
important in industrial automation due to characteristics like
applications high performance, are very attractive for applications
with limited space and reducing the need to eliminate because they
have reduced size and volume and can operate in a wide speed range,
without independent ventilation. By using experimental data and
genetic algorithm we have been able to extract values for both the
motor inductance and the electromechanical coupling constant, which
are then compared to measured and/or expected values.
Abstract: The present study is an attempt to provide a relatively
comprehensive preview of the Iranian English translators’ perception
on Machine Translation. Furthermore, the study tries to shed light on
the status of implementation of Machine Translation among the
Iranian English Translators. To reach the aforementioned objectives,
the Localization Industry Standards Association’s questioner for
measuring perceptions with regard to the adoption of a technology
innovation was adapted and used to investigate the perception and
implementation of Machine Translation applications by the Iranian
English language translators. The participants of the study were 224
last-year undergraduate Iranian students of English translation at 10
universities across the country. The study revealed a very low level of
adoption and a very high level of willingness to get familiar with and
learn about Machine Translation, as well as a positive perception of
and attitude toward Machine Translation by the Iranian English
translators.
Abstract: The detection of moving objects from a video image
sequences is very important for object tracking, activity recognition,
and behavior understanding in video surveillance.
The most used approach for moving objects detection / tracking is
background subtraction algorithms. Many approaches have been
suggested for background subtraction. But, these are illumination
change sensitive and the solutions proposed to bypass this problem
are time consuming.
In this paper, we propose a robust yet computationally efficient
background subtraction approach and, mainly, focus on the ability to
detect moving objects on dynamic scenes, for possible applications in
complex and restricted access areas monitoring, where moving and
motionless persons must be reliably detected. It consists of three
main phases, establishing illumination changes invariance,
background/foreground modeling and morphological analysis for
noise removing.
We handle illumination changes using Contrast Limited Histogram
Equalization (CLAHE), which limits the intensity of each pixel to
user determined maximum. Thus, it mitigates the degradation due to
scene illumination changes and improves the visibility of the video
signal. Initially, the background and foreground images are extracted
from the video sequence. Then, the background and foreground
images are separately enhanced by applying CLAHE.
In order to form multi-modal backgrounds we model each channel
of a pixel as a mixture of K Gaussians (K=5) using Gaussian Mixture
Model (GMM). Finally, we post process the resulting binary
foreground mask using morphological erosion and dilation
transformations to remove possible noise.
For experimental test, we used a standard dataset to challenge the
efficiency and accuracy of the proposed method on a diverse set of
dynamic scenes.
Abstract: Meeting the growth in demand for digital services
such as social media, telecommunications, and business and cloud
services requires large scale data centres, which has led to an increase
in their end use energy demand. Generally, over 30% of data centre
power is consumed by the necessary cooling overhead. Thus energy
can be reduced by improving the cooling efficiency. Air and liquid
can both be used as cooling media for the data centre. Traditional
data centre cooling systems use air, however liquid is recognised as a
promising method that can handle the more densely packed data
centres. Liquid cooling can be classified into three methods; rack heat
exchanger, on-chip heat exchanger and full immersion of the
microelectronics. This study quantifies the improvements of heat
transfer specifically for the case of immersed microelectronics by
varying the CPU and heat sink location. Immersion of the server is
achieved by filling the gap between the microelectronics and a water
jacket with a dielectric liquid which convects the heat from the CPU
to the water jacket on the opposite side. Heat transfer is governed by
two physical mechanisms, which is natural convection for the fixed
enclosure filled with dielectric liquid and forced convection for the
water that is pumped through the water jacket. The model in this
study is validated with published numerical and experimental work
and shows good agreement with previous work. The results show that
the heat transfer performance and Nusselt number (Nu) is improved
by 89% by placing the CPU and heat sink on the bottom of the
microelectronics enclosure.
Abstract: The concentrations of cadmium and lead in sewage
sludge samples were determined by Atomic Absorption
Spectrometric Method. Samples of sewage sludge were obtained
from three sewage treatment plants localised in Middle Region of
Libya (Misrata, Msallata and Tarhünah cities).
The results shows that, the mean levels of Cadmium for all regions
are ranges from 81 to 123.4 ppm and these values are higher than the
limitations for the international standard which are not registered
more than 50 ppm (dry weight) in USA, Egypt and the EU countries.
While, the lead concentrations are ranged from 8.0 to 189.2 ppm and
all values are within the standard limits which graduated between
(275–613) ppm.