Abstract: Cantilever L-shaped walls are known to be relatively economical as retaining solution. The design starts by proportioning the wall dimensions for which the stability is checked for. A ratio between the lengths of the base and the stem, falling between 0.5 to 0.7 ensure in most case the stability requirements, however, the displacement pattern of the wall in terms of rotations and translations, and the lateral pressure profile, do not have the same figure for all wall’s proportioning, as it is usually assumed. In the present work the results of a numerical analysis are presented, different wall geometries were considered. The results show that the proportioning governs the equilibrium between the instantaneous rotation and the translation of the wall-toe, also, the lateral pressure estimation based on the average value between the at-rest and the active pressure, recommended by most design standards, is found to be not applicable for all walls.
Abstract: Fuzzy Load forecasting plays a paramount role in the operation and management of power systems. Accurate estimation of future power demands for various lead times facilitates the task of generating power reliably and economically. The forecasting of future loads for a relatively large lead time (months to few years) is studied here (long term load forecasting). Among the various techniques used in forecasting load, artificial intelligence techniques provide greater accuracy to the forecasts as compared to conventional techniques. Fuzzy Logic, a very robust artificial intelligent technique, is described in this paper to forecast load on long term basis. The paper gives a general algorithm to forecast long term load. The algorithm is an Extension of Short term load forecasting method to Long term load forecasting and concentrates not only on the forecast values of load but also on the errors incorporated into the forecast. Hence, by correcting the errors in the forecast, forecasts with very high accuracy have been achieved. The algorithm, in the paper, is demonstrated with the help of data collected for residential sector (LT2 (a) type load: Domestic consumers). Load, is determined for three consecutive years (from April-06 to March-09) in order to demonstrate the efficiency of the algorithm and to forecast for the next two years (from April-09 to March-11).
Abstract: Finding the shortest path between two positions is a
fundamental problem in transportation, routing, and communications
applications. In robot motion planning, the robot should pass around
the obstacles touching none of them, i.e. the goal is to find a
collision-free path from a starting to a target position. This task has
many specific formulations depending on the shape of obstacles,
allowable directions of movements, knowledge of the scene, etc.
Research of path planning has yielded many fundamentally different
approaches to its solution, mainly based on various decomposition
and roadmap methods. In this paper, we show a possible use of
visibility graphs in point-to-point motion planning in the Euclidean
plane and an alternative approach using Voronoi diagrams that
decreases the probability of collisions with obstacles. The second
application area, investigated here, is focused on problems of finding
minimal networks connecting a set of given points in the plane using
either only straight connections between pairs of points (minimum
spanning tree) or allowing the addition of auxiliary points to the set
to obtain shorter spanning networks (minimum Steiner tree).
Abstract: The purpose of this study is to research on thoughts transmitted from virtual fitting-room and to deduce discussion in an auxiliary narrative way. The research structure is based on 3D virtual fitting-room as the research subject. Initially, we will discuss the principles of narrate study, User Demand and so on by using a narrative design pattern to transmit their objective indications of “people-situation-reason-object", etc, and then to analyze the virtual fitting-room examples that are able to provide a new thinking for designers who engaged in clothing related industry – which comes in “story telling" and “user-centered design" forms. Clothing designs are not just to cover up the body to keep warm but to draw closer to people-s demand physiologically and psychologically through interactive designs so as to achieve cognition between people and environment. In the “outside" goal of clothing-s functional designs, we use tribal group-s behavior characteristics to “transform" the existing personal cultural stories, and “reform" them to design appropriate interactive products. Synthesizing the above matters, apart from being able to regard “narrate" as a kind of functional thinking process, we are also able to regard it as a kind of choice, arrangement and an activity of story expression, allowing interactive design-s spirit, product characteristics and experience ideas be transmitted to target tribal group in a visual image performance method. It is a far more confident and innovative attempt, and meanwhile, able to achieve entertainment, joyful and so forth fundamental interactive transmissions. Therefore, this study takes “user-centered design" thinking as a basis to establish a set of clothing designs with interactive experience patterns and to assist designers to examine the five sensual feeling of interactive demands in order to initiate a new value in textile industry.
Abstract: In the last decade digital watermarking procedures have
become increasingly applied to implement the copyright protection
of multimedia digital contents distributed on the Internet. To this
end, it is worth noting that a lot of watermarking procedures
for images and videos proposed in literature are based on spread
spectrum techniques. However, some scepticism about the robustness
and security of such watermarking procedures has arisen because
of some documented attacks which claim to render the inserted
watermarks undetectable. On the other hand, web content providers
wish to exploit watermarking procedures characterized by flexible and
efficient implementations and which can be easily integrated in their
existing web services frameworks or platforms. This paper presents
how a simple spread spectrum watermarking procedure for MPEG-2
videos can be modified to be exploited in web contexts. To this end,
the proposed procedure has been made secure and robust against some
well-known and dangerous attacks. Furthermore, its basic scheme
has been optimized by making the insertion procedure adaptive with
respect to the terminals used to open the videos and the network transactions
carried out to deliver them to buyers. Finally, two different
implementations of the procedure have been developed: the former
is a high performance parallel implementation, whereas the latter is
a portable Java and XML based implementation. Thus, the paper
demonstrates that a simple spread spectrum watermarking procedure,
with limited and appropriate modifications to the embedding scheme,
can still represent a valid alternative to many other well-known and
more recent watermarking procedures proposed in literature.
Abstract: The quantum mechanics simulation was applied for
calculating the interaction force between 2 molecules based on atomic level. For the simple extractive distillation system, it is ternary
components consisting of 2 closed boiling point components (A,lower boiling point and B, higher boiling point) and solvent (S). The
quantum mechanics simulation was used to calculate the intermolecular force (interaction force) between the closed boiling
point components and solvents consisting of intermolecular between
A-S and B-S.
The requirement of the promising solvent for extractive distillation
is that solvent (S) has to form stronger intermolecular force with only
one component than the other component (A or B). In this study, the
systems of aromatic-aromatic, aromatic-cycloparaffin, and paraffindiolefin
systems were selected as the demonstration for solvent
selection. This study defined new term using for screening the solvents called relative interaction force which is calculated from the
quantum mechanics simulation. The results showed that relative
interaction force gave the good agreement with the literature data
(relative volatilities from the experiment). The reasons are discussed. Finally, this study suggests that quantum mechanics results can improve the relative volatility estimation for screening the solvents leading to reduce time and money consuming
Abstract: This paper presents an effective traffic lights detection
method at the night-time. First, candidate blobs of traffic lights are
extracted from RGB color image. Input image is represented on the
dominant color domain by using color transform proposed by Ruta,
then red and green color dominant regions are selected as candidates.
After candidate blob selection, we carry out shape filter for noise
reduction using information of blobs such as length, area, area of
boundary box, etc. A multi-class classifier based on SVM (Support
Vector Machine) applies into the candidates. Three kinds of features
are used. We use basic features such as blob width, height, center
coordinate, area, area of blob. Bright based stochastic features are also
used. In particular, geometric based moment-s values between
candidate region and adjacent region are proposed and used to improve
the detection performance. The proposed system is implemented on
Intel Core CPU with 2.80 GHz and 4 GB RAM and tested with the
urban and rural road videos. Through the test, we show that the
proposed method using PF, BMF, and GMF reaches up to 93 % of
detection rate with computation time of in average 15 ms/frame.
Abstract: Hybridization refers to the crossing breeding of two
plants. Coefficient of Parentage (COP) is used by the plant breeders
to determine the genetic diversity across various varieties so as to
incorporate the useful characters of the two varieties to develop a
new crop variety with particular useful characters. Genetic Diversity
is the prerequisite for any cultivar development program. Genetic
Diversity depends upon the pedigree information of the varieties
based on particular levels. Pedigree refers to the parents of a
particular variety at various levels. This paper discusses the searching
and analyses of different possible pairs of varieties selected on the
basis of morphological characters, Climatic conditions and Nutrients
so as to obtain the most optimal pair that can produce the required
crossbreed variety. An algorithm was developed to determine the
coefficient of parentage (COP) between the selected wheat varieties.
Dummy values were used wherever actual data was not available.
Abstract: A game animals – elk (Alces alces), deer (Cervus
elaphus), roe deer (Capreolus capreolus) or wild boar (Sus scrofa
scrofa) - every autumn and winter period provide an excellent
investment, diversification of many consumer meals. In last years
consumption and assortiment of game meat products significantly
increase. Investigations about biochemical composition of game meat
are not very much. The meat of wild animals is more favourable for
human health because it has lower saturated fatty acids content, but
higher content of protein. Therefore the aim of investigations was to
compare biochemical composition of ungulates obtained in
Latvia.Investigations were carried out in wild animals different
regions of Latvia. In the studied samples protein, intramuscular fat,
fatty acids and cholesterol were determined. The biochemical
analysis of 54 samples were done. Results of analysis showed that
protein content 22.36 – 22.92% of all types of meat samples is not
different statistically, significantly lower fat content 1.33 ± 0.88%
had elk meat samples and 1.59 ± 0.59% roe deer samples. Content of
cholesterol was various 64.41 – 95.07% in the ruminant meat
samples of different species. From the dietetic point of view the best
composition of fatty acids has meat samples of roe deer.
Abstract: A new hybrid coding method for compressing
animated polygonal meshes is presented. This paper assumes
the simplistic representation of the geometric data: a temporal
sequence of polygonal meshes for each discrete frame of the
animated sequence. The method utilizes a delta coding and an
octree-based method. In this hybrid method, both the octree
approach and the delta coding approach are applied to each
single frame in the animation sequence in parallel. The
approach that generates the smaller encoded file size is chosen
to encode the current frame. Given the same quality
requirement, the hybrid coding method can achieve much
higher compression ratio than the octree-only method or the
delta-only method. The hybrid approach can represent 3D
animated sequences with higher compression factors while
maintaining reasonable quality. It is easy to implement and have
a low cost encoding process and a fast decoding process, which
make it a better choice for real time application.
Abstract: Power system stabilizers (PSS) are now routinely used in the industry to damp out power system oscillations. In this paper, particle swarm optimization (PSO) technique is applied to design a robust power system stabilizer (PSS). The design problem of the proposed controller is formulated as an optimization problem and PSO is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor speed of the generator is involved; stability performance of the system is improved. The non-linear simulation results are presented under wide range of operating conditions; disturbances at different locations as well as for various fault clearing sequences to show the effectiveness and robustness of the proposed controller and their ability to provide efficient damping of low frequency oscillations. Further, all the simulations results are compared with a conventionally designed power system stabilizer to show the superiority of the proposed design approach.
Abstract: The scattering effect of light in fog improves the
difficulty in visibility thus introducing disturbances in transport
facilities in urban or industrial areas causing fatal accidents or public
harassments, therefore, developing an enhanced fog vision system
with radio wave to improvise the way outs of these severe problems
is really a big challenge for researchers. Series of experimental
studies already been done and more are in progress to know the
weather effect on radio frequencies for different ranges. According to
Rayleigh scattering Law, the propagating wavelength should be
greater than the diameter of the particle present in the penetrating
medium. Direct wave RF signal thus have high chance of failure to
work in such weather for detection of any object. Therefore an
extensive study was required to find suitable region in the RF band
that can help us in detecting objects with proper shape. This paper
produces some results on object detection using 912 MHz band with
successful detection of the persistence of any object coming under the
trajectory of a vehicle navigating in indoor and outdoor environment.
The developed images are finally transformed to video signal to
enable continuous monitoring.
Abstract: Fuzzy random variables have been introduced as an imprecise concept of numeric values for characterizing the imprecise knowledge. The descriptive parameters can be used to describe the primary features of a set of fuzzy random observations. In fuzzy environments, the expected values are usually represented as fuzzy-valued, interval-valued or numeric-valued descriptive parameters using various metrics. Instead of the concept of area metric that is usually adopted in the relevant studies, the numeric expected value is proposed by the concept of distance metric in this study based on two characters (fuzziness and randomness) of FRVs. Comparing with the existing measures, although the results show that the proposed numeric expected value is same with those using the different metric, if only triangular membership functions are used. However, the proposed approach has the advantages of intuitiveness and computational efficiency, when the membership functions are not triangular types. An example with three datasets is provided for verifying the proposed approach.
Abstract: The purpose of this study was to examine to what
extend classroom management efficacy, marital status, gender, and
teaching experience predict burnout among primary school teachers.
Participants of this study were 523 (345 female, 178 male) teachers
who completed inventories. The results of multiple regression
analysis indicated that three dimensions of teacher burnout
(Emotional Exhaustion, Depersonalization, Personal
Accomplishment) were affected differently from four predictor
variables. Findings indicated that for the emotional exhaustion,
classroom management efficacy, marital status and teaching
experience; for depersonalization dimension, classroom management
efficacy and marital status and finally for the personal
accomplishment dimension, classroom management efficacy, gender,
and teaching experience were significant predictors.
Abstract: Response surface methodology with Box–Benhken (BB) design of experiment approach has been utilized to study the mechanism of interface slip damping in layered and jointed tack welded beams with varying surface roughness. The design utilizes the initial amplitude of excitation, tack length and surface roughness at the interfaces to develop the model for the logarithmic damping decrement of the layered and jointed welded structures. Statistically designed experiments have been performed to estimate the coefficients in the mathematical model, predict the response, and check the adequacy of the model. Comparison of predicted and experimental response values outside the design conditions have shown good correspondence, implying that empirical model derived from response surface approach can be effectively used to describe the mechanism of interface slip damping in layered and jointed tack welded structures.
Abstract: The MFCAV Riemann solver is practically used in many Lagrangian or ALE methods due to its merit of sharp shock profiles and rarefaction corners, though very often with numerical oscillations. By viewing it as a modification of the WWAM Riemann solver, we apply the MFCAV Riemann solver to the Lagrangian method recently developed by Maire. P. H et. al.. The numerical experiments show that the application is successful in that the shock profiles and rarefaction corners are sharpened compared with results obtained using other Riemann solvers. Though there are still numerical oscillations, they are within the range of the MFCAV applied in onther Lagrangian methods.
Abstract: Predictions of flow and heat transfer characteristics and shape optimization in internally finned circular tubes have been performed on three-dimensional periodically fully developed turbulent flow and thermal fields. For a trapezoidal fin profile, the effects of fin height h, upper fin widths d1, lower fin widths d2, and helix angle of fin ? on transport phenomena are investigated for the condition of fin number of N = 30. The CFD and mathematical optimization technique are coupled in order to optimize the shape of internally finned tube. The optimal solutions of the design variables (i.e., upper and lower fin widths, fin height and helix angle) are numerically obtained by minimizing the pressure loss and maximizing the heat transfer rate, simultaneously, for the limiting conditions of d1 = 0.5~1.5 mm, d2 = 0.5~1.5 mm, h= 0.5~1.5mm, ? = 10~30 degrees. The fully developed flow and thermal fields are predicted using the finite volume method and the optimization is carried out by means of the multi-objective genetic algorithm that is widely used in the constrained nonlinear optimization problem.
Abstract: In conventional seedling production, the seedlings are
being grown in the open field under natural conditions. Here they are
susceptible to sudden changes in climate were their quality and yield
is affected. Quality seedlings are essential for good growth and
performance of crops in main field; they serve as a foundation for the
economic returns to the farmer. Producing quality seedling demands
usage of hybrid seeds as they have the ability to result in better yield,
greater uniformity, improved color, disease resistance, and so forth.
Hybrid seed production poses major operational challenge and its
seed use efficiency plays an important role. Thus in order to
overcome the difficulties currently present in conventional seedling
production and to efficiently use hybrid seeds, ITC Limited Agri
Business Divisions - Sustainability Cell as conceptualized a novel
method of seedling production unit for farmers in West Godavari
District of Andhra Pradesh. The “Green House based Float Seedling"
methodology aims at a protected cultivation technique wherein the
micro climate surrounding the plant/seedling body is controlled
partially or fully as per the requirement of the species. This paper
reports on the techno economic evaluation of green house for
cultivation of float based seedling production with experimental
results that was attained from the pilot implementation in West
Godavari District, Rajahmundry region of India.
Abstract: In this study Homotopy Perturbation Method (HPM) is employed to investigate free vibration of an Euler beam with variable stiffness resting on an elastic foundation. HPM is an easy-to-use and very efficient technique for the solution of linear or nonlinear problems. HPM produces analytical approximate expression which is continuous in the solution domain. This work shows that HPM is a promising method for free vibration analysis of nonuniform Euler beams on elastic foundation. Several case problems have been solved by using the technique and solutions have been compared with those available in the literature.
Abstract: An IEC technique is described for a multi-objective
search of conceptual solutions. The survivability of solutions is
influenced by both model-based fitness and subjective human
preferences. The concepts- preferences are articulated via a hierarchy
of sub-concepts. The suggested method produces an objectivesubjective
front. Academic example is employed to demonstrate the
proposed approach.