Abstract: Due to increased number of terrorist attacks in recent years, loads induced by explosions need to be incorporated in building designs. For safer performance of a structure, its foundation should have sufficient strength and stability. Therefore, prior to any reconstruction or rehabilitation of a building subjected to blast, it is important to examine adverse effects on the foundation caused by blast induced ground shocks. This paper evaluates the effects of a buried explosion on a pile foundation. It treats the dynamic response of the pile in saturated sand, using explicit dynamic nonlinear finite element software LS-DYNA. The blast induced wave propagation in the soil and the horizontal deformation of pile are presented and the results are discussed. Further, a parametric study is carried out to evaluate the effect of varying the explosive shape on the pile response. This information can be used to evaluate the vulnerability of piled foundations to credible blast events as well as develop guidance for their design.
Abstract: In this paper, the effect of bolt clamping force on the fatigue behavior of bolted single lap joints of aluminum alloy 2024- T3 have been studied using numerical finite element method. To do so, a three dimensional model according to the bolted single lap joint has been created and numerical analysis has been carried out using finite element based package. Then the stress distribution and also the slip amplitudes have been calculated in the critical regions and the outcome have been compared with the available experimental fatigue tests results. The numerical results show that in low applied clamping force, the fatigue failure of the specimens occur around the stress concentration location (the bolted hole edge) due to the tensile stresses and thus fatigue crack propagation, but with increase of the clamping force, the fatigue life increases and the cracks nucleate and propagate far from the hole edge because of fretting fatigue. In other words, with the further increase of clamping force value of the joint, the fatigue life reduces due to occurrence of the fretting fatigue in the critical location where the slip amplitude is within its critical occurs earlier.
Abstract: Topology Optimization is a defined as the method of
determining optimal distribution of material for the assumed design
space with functionality, loads and boundary conditions [1].
Topology optimization can be used to optimize shape for the
purposes of weight reduction, minimizing material requirements or
selecting cost effective materials [2]. Topology optimization has been
implemented through the use of finite element methods for the
analysis, and optimization techniques based on the method of moving
asymptotes, genetic algorithms, optimality criteria method, level sets
and topological derivatives. Case study of Typical “Fuselage design"
is considered for this paper to explain the benefits of Topology
Optimization in the design cycle. A cylindrical shell is assumed as
the design space and aerospace standard pay loads were applied on
the fuselage with wing attachments as constraints. Then topological
optimization is done using Finite Element (FE) based software. This
optimization results in the structural concept design which satisfies
all the design constraints using minimum material.
Abstract: A brushless DC motor with integrated drive circuit for air management system is presented. Using magnetic equivalent circuit model a basic design of the motor is determined, and specific configurations are inspected thanks to finite element analysis. In order to reduce an unbalanced magnetic force in an axial direction, induced forces between a stator core and a permanent magnet are calculated with respect to the relative positions of them. For the high efficiency, and high power density, BLDC motor and drive are developed. Also vibration mode and eccentricity of a rotor are considered at the rated and maximum rotational speed Through the experimental results, a validity of the simulated one is confirmed.
Abstract: This paper focuses on the Mega-Sub Controlled
Structure Systems (MSCSS) performances and characteristics
regarding the new control principle contained in MSCSS subjected to
strong earthquake excitations. The adopted control scheme consists of
modulated sub-structures where the control action is achieved by
viscous dampers and sub-structure own configuration. The
elastic-plastic time history analysis under severe earthquake excitation
is analyzed base on the Finite Element Analysis Method (FEAM), and
some comparison results are also given in this paper. The result shows
that the MSCSS systems can remarkably reduce vibrations effects
more than the mega-sub structure (MSS). The study illustrates that the
improved MSCSS presents good seismic resistance ability even at 1.2g
and can absorb seismic energy in the structure, thus imply that
structural members cross section can be reduce and achieve to good
economic characteristics. Furthermore, the elasto-plastic analysis
demonstrates that the MSCSS is accurate enough regarding
international building evaluation and design codes. This paper also
shows that the elasto-plastic dynamic analysis method is a reasonable
and reliable analysis method for structures subjected to strong
earthquake excitations and that the computed results are more precise.
Abstract: In present work, prediction the effect of nose radius, rz (mm) on the equivalent strain (PEEQ) and surface finish during the machining of titanium alloy (Ti-6Al-4V) through orthogonal cutting process. The results were performed at several of the nose radiuses, rz (mm) while the cutting speed, vc (m/min), feed rate, f (mm/tooth) and depth of cut, d (mm) were remained constant. The equivalent plastic strain (PEEQ) was estimated by using finite element modeling (FEM) and applied through ABAQUS/EXPLICIT software. The simulation results led to conclude that the equivalent plastic strain (PEEQ) was increased and surface roughness (Ra) decreased when increasing nose radius, rz (mm) during the machining of titanium alloy (Ti–6Al–4V) in dry cutting conditions.
Abstract: The sand production problem has led researchers into making various attempts to understand the phenomenon. The generally accepted concept is that the occurrence of sanding is due to the in-situ stress conditions and the induced changes in stress that results in the failure of the reservoir sandstone during hydrocarbon production from wellbores. By using a hypothetical cased (perforated) well, an approach to the problem is presented here by using Finite Element numerical modelling techniques. In addition to the examination of the erosion problem, the influence of certain key parameters is studied in order to ascertain their effect on the failure and subsequent erosion process. The major variables investigated include: drawdown, perforation depth, and the erosion criterion. Also included is the determination of the optimal mud pressure for given operational and reservoir conditions. The improved understanding between parameters enables the choice of optimal values to minimize sanding during oil production.
Abstract: A biophysically based multilayer continuum model of the facial soft tissue composite has been developed for simulating wrinkle formation. The deformed state of the soft tissue block was determined by solving large deformation mechanics equations using the Galerkin finite element method. The proposed soft tissue model is composed of four layers with distinct mechanical properties. These include stratum corneum, epidermal-dermal layer (living epidermis and dermis), subcutaneous tissue and the underlying muscle. All the layers were treated as non-linear, isotropic Mooney Rivlin materials. Contraction of muscle fibres was approximated using a steady-state relationship between the fibre extension ratio, intracellular calcium concentration and active stress in the fibre direction. Several variations of the model parameters (stiffness and thickness of epidermal-dermal layer, thickness of subcutaneous tissue layer) have been considered.
Abstract: This paper presents work characterizing finite element
performance boundaries within which live, interactive finite element
modeling is feasible on current and emerging systems. These results
are based on wide-ranging tests performed using a prototype finite
element program implemented specifically for this study, thereby enabling
the unified investigation of numerous direct and iterative solver
strategies and implementations in a variety of modeling contexts.
The results are intended to be useful for researchers interested in
interactive analysis by providing baseline performance estimates, to
give guidance in matching solution strategies to problem domains,
and to spur further work addressing the challenge of extending the
present boundaries.
Abstract: During the last decade ultrafine grained (UFG) and nano-structured (NS) materials have experienced a rapid development. In this research work finite element analysis has been carried out to investigate the plastic strain distribution in equal channel angular process (ECAP). The magnitudes of Standard deviation (S. D.) and inhomogeneity index (Ci) were compared for different ECAP passes. Verification of a three-dimensional finite element model was performed with experimental tests. Finally the mechanical property including impact energy of ultrafine grained pure commercially pure Aluminum produced by severe plastic deformation method has been examined. For this aim, equal channel angular pressing die with the channel angle, outer corner angle and channel diameter of 90°, 20° and 20mm had been designed and manufactured. Commercial pure Aluminum billets were ECAPed up to four passes by route BC at the ambient temperature. The results indicated that there is a great improvement at the hardness measurement, yield strength and ultimate tensile strength after ECAP process. It is found that the magnitudes of HV reach 67HV from 21HV after the final stage of process. Also, about 330% and 285% enhancement at the YS and UTS values have been obtained after the fourth pass as compared to the as-received conditions, respectively. On the other hand, the elongation to failure and impact energy have been reduced by 23% and 50% after imposing four passes of ECAP process, respectively.
Abstract: Investigation of sandy clay behavior is important since
urban development demands mean that sandy clay areas are
increasingly encountered, especially for transportation
infrastructures. This paper presents the results of the finite element
analysis of the direct shear test (under three vertical loading 44, 96
and 192 kPa) and discusses the effects of different parameters such as
cohesion, friction angle and Young's modulus on the shear strength of
sandy clay. The numerical model was calibrated against the
experimental results of large-scale direct shear tests. The results have
shown that the shear strength was increased with increase in friction
angle and cohesion. However, the shear strength was not influenced
by raising the friction angle at normal stress of 44 kPa. Also, the
effect of different young's modulus factors on stress-strain curve was
investigated.
Abstract: In this paper, a new time discontinuous expanded mixed finite element method is proposed and analyzed for two-order convection-dominated diffusion problem. The proofs of the stability of the proposed scheme and the uniqueness of the discrete solution are given. Moreover, the error estimates of the scalar unknown, its gradient and its flux in the L1( ¯ J,L2( )-norm are obtained.
Abstract: Fatigue life prediction and evaluation are the key
technologies to assure the safety and reliability of automotive rubber
components. The objective of this study is to develop the fatigue
analysis process for vulcanized rubber components, which is
applicable to predict fatigue life at initial product design step. Fatigue
life prediction methodology of vulcanized natural rubber was
proposed by incorporating the finite element analysis and fatigue
damage parameter of maximum strain appearing at the critical location
determined from fatigue test. In order to develop an appropriate
fatigue damage parameter of the rubber material, a series of
displacement controlled fatigue test was conducted using threedimensional
dumbbell specimen with different levels of mean
displacement. It was shown that the maximum strain was a proper
damage parameter, taking the mean displacement effects into account.
Nonlinear finite element analyses of three-dimensional dumbbell
specimens were performed based on a hyper-elastic material model
determined from the uni-axial tension, equi-biaxial tension and planar
test. Fatigue analysis procedure employed in this study could be used
approximately for the fatigue design.
Abstract: The paper deals with determination of electromagnetic
and temperature field distribution of induction heating system used
for pipe brazing. The problem is considered as coupled – time
harmonic electromagnetic and transient thermal field. It has been
solved using finite element method. The detailed maps of
electromagnetic and thermal field distribution have been obtained.
The good understanding of the processes in the considered system
ensures possibilities for control, management and increasing the
efficiency of the welding process.
Abstract: The psychological and physical trauma associated with the loss of a human limb can severely impact on the quality of life of an amputee rendering even the most basic of tasks very difficult. A prosthetic device can be of great benefit to the amputee in the performance of everyday human tasks. This paper outlines a proposed mechanical design of a 12 degree-of-freedom SMA actuated artificial hand. It is proposed that the SMA wires be embedded intrinsically within the hand structure which will allow for significant flexibility for use either as a prosthetic hand solution, or as part of a complete lower arm prosthetic solution. A modular approach is taken in the design facilitating ease of manufacture and assembly, and more importantly, also allows the end user to easily replace SMA wires in the event of failure. A biomimetric approach has been taken during the design process meaning that the artificial hand should replicate that of a human hand as far as is possible with due regard to functional requirements. The proposed design has been exposed to appropriate loading through the use of finite element analysis (FEA) to ensure that it is structurally sound. Theoretical analysis of the mechanical framework was also carried out to establish the limits of the angular displacement and velocity of the finger tip as well finger tip force generation. A combination of various polymers and Titanium, which are suitably lightweight, are proposed for the manufacture of the design.
Abstract: –In this paper the damage in clamped-free, clampedclamped and free-free beam are analyzed considering samples
without and with structural modifications. The damage location is
investigated by the use of the bispectrum and wavelet analysis. The
mathematical models are obtained using 2D elasticity theory and the
Finite Element Method (FEM). The numerical and experimental data
are approximated using the Particle Swarm Optimizer (PSO) method
and this way is possible to adjust the localization and the severity of
the damage. The experimental data are obtained through
accelerometers placed along the sample. The system is excited using
impact hammer.
Abstract: Antiseismic property of telecommunication equipment
is very important for the grasp of the damage and the restoration after
earthquake. Telecommunication business operators are regulating
seismic standard for their equipments. These standards are organized
to simulate the real seismic situations and usually define the minimum
value of first natural frequency of the equipments or the allowable
maximum displacement of top of the equipments relative to bottom.
Using the finite element analysis, natural frequency can be obtained
with high accuracy but the relative displacement of top of the
equipments is difficult to predict accurately using the analysis.
Furthermore, in the case of simulating the equipments with access
floor, predicting the relative displacement of top of the equipments
become more difficult.
In this study, using enormous experimental datum, an empirical
formula is suggested to forecast the relative displacement of top of the
equipments. Also it can be known that which physical quantities are
related with the relative displacement.
Abstract: Rise/span ratio has been mentioned as one of the
reasons which contribute to the lower buckling load as compared to
the Classical theory buckling load but this ratio has not been quantified
in the equation. The purpose of this study was to determine a more
realistic buckling load by quantifying the effect of the rise/span ratio
because experiments have shown that the Classical theory
overestimates the load. The buckling load equation was derived based
on the theorem of work done and strain energy. Thereafter, finite
element modeling and simulation using ABAQUS was done to
determine the variables that determine the constant in the derived
equation. The rise/span was found to be the determining factor of the
constant in the buckling load equation. The derived buckling load
correlates closely to the load obtained from experiments.
Abstract: This paper presents the modeling of a MEMS based accelerometer in order to detect the presence of a wheel flat in the railway vehicle. A haversine wheel flat is assigned to one wheel of a 5 DOF pitch plane vehicle model, which is coupled to a 3 layer track model. Based on the simulated acceleration response obtained from the vehicle-track model, an accelerometer is designed that meets all the requirements to detect the presence of a wheel flat. The proposed accelerometer can survive in a dynamic shocking environment with acceleration up to ±150g. The parameters of the accelerometer are calculated in order to achieve the required specifications using lumped element approximation and the results are used for initial design layout. A finite element analysis code (COMSOL) is used to perform simulations of the accelerometer under various operating conditions and to determine the optimum configuration. The simulated results are found within about 2% of the calculated values, which indicates the validity of lumped element approach. The stability of the accelerometer is also determined in the desired range of operation including the condition under shock.
Abstract: The use of the mechanical simulation (in particular the finite element analysis) requires the management of assumptions in order to analyse a real complex system. In finite element analysis (FEA), two modeling steps require assumptions to be able to carry out the computations and to obtain some results: the building of the physical model and the building of the simulation model. The simplification assumptions made on the analysed system in these two steps can generate two kinds of errors: the physical modeling errors (mathematical model, domain simplifications, materials properties, boundary conditions and loads) and the mesh discretization errors. This paper proposes a mesh adaptive method based on the use of an h-adaptive scheme in combination with an error estimator in order to choose the mesh of the simulation model. This method allows us to choose the mesh of the simulation model in order to control the cost and the quality of the finite element analysis.