Abstract: Calcium Phosphate Cement (CPC) due to its high bioactivity and optimum bioresorbability shows excellent bone regeneration capability. Despite it has limited applications as bone implant due to its macro-porous microstructure causing its poor mechanical strength. The reinforcement of apatitic CPCs with biocompatible fibre glass phase is an attractive area of research to improve upon its mechanical strength. Here, we study the setting behaviour of Si-doped and un-doped α tri calcium phosphate (α - TCP) based CPC and its reinforcement with addition of E-glass fibre. Alpha Tri calcium phosphate powders were prepared by solid state sintering of CaCO3 , CaHPO4 and Tetra Ethyl Ortho Silicate (TEOS) was used as silicon source to synthesize Si doped α-TCP powders. Both initial and final setting time of the developed cement was delayed because of Si addition. Crystalline phases of HA (JCPDS 9- 432), α-TCP (JCPDS 29-359) and β-TCP (JCPDS 9-169) were detected in the X-ray diffraction (XRD) pattern after immersion of CPC in simulated body fluid (SBF) for 0 hours to 10 days. As Si incorporation in the crystal lattice stabilized the TCP phase, Si doped CPC showed little slower rate of conversion into HA phase as compared to un-doped CPC. The SEM image of the microstructure of hardened CPC showed lower grain size of HA in un-doped CPC because of premature setting and faster hydrolysis of un-doped CPC in SBF as compared that in Si-doped CPC. Premature setting caused generation of micro and macro porosity in un-doped CPC structure which resulted in its lower mechanical strength as compared to that in Si-doped CPC. It was found that addition of 10 wt% of E-glass fibre into Si-doped α-TCP increased the average DTS of CPC from 8 MPa to 15 MPa as the fibres could resists the propagation of crack by deflecting the crack tip. Our study shows that biocompatible E-glass fibre in optimum proportion in CPC matrix can enhance the mechanical strength of CPC without affecting its biocompatibility.
Abstract: Temperature effect on the performance of a photovoltaic module is one of the main concerns that face this renewable energy, especially in hot arid region, e.g. United Arab Emirates. Overheating of the PV modules reduces the open circuit voltage and the efficiency of the modules dramatically. In this work, water-cooling is developed to enhance the performance of PV modules. Different scenarios are tested under UAE weather conditions: front, back and double cooling. A spraying system is used for the front cooling whether a direct contact water system is used for the back cooling. The experimental results are compared to non-cooling module and the performance of the PV module is determined for different situations. The experimental results show that the front cooling is more effective than the back cooling and may decrease the temperature of the PV module significantly.
Abstract: Plate is one of the popular structural elements used in a wide range of industries and structures. They may be subjected to blast loads during explosion events, missile attacks or aircraft attacks. This study is to investigate dynamic responses of the rectangular plate subjected to explosive loads. The effects of material properties and plate thickness on responses of the plate are to be investigated. The compressive pressure is applied to the surface of the plate. Different amounts of thickness in the range from 1mm to 30mm are considered for the plate to evaluate the changes in responses of the plate with respect to plate thickness. Two different properties are considered for the steel. First, the analysis is performed by considering only the elastic-plastic properties for the steel plate. Later on damping is considered to investigate its effects on the responses of the plate. To do analysis, numerical method using a finite element based package ABAQUS is applied. Finally, dynamic responses and graphs showing the relation between maximum displacement of the plate and aim parameters are provided.
Abstract: The objective of this paper is to analyze the role played by the institute of the public hearings in the Brazilian Supreme Court. The public hearings are regulated since 1999 by the Brazilian Laws nº 9.868, nº 9.882 and by the Intern Regiment of the Brazilian Supreme Court. According to this legislation, the public hearings are supposed to be called when a matter of circumstance of fact must be clarified, what can be done through the hearing of the testimonies of persons with expertise and authority in the theme related to the cause. This work aims to investigate what is the role played by the public hearings and by the experts in the Brazilian Supreme Court. The hypothesis of this research is that: (I) The public hearings in the Brazilian Supreme Court are used to uphold a rhetoric of a democratic legitimacy of the Court`s decisions; (II) The Legislative intentions have been distorted. To test this hypothesis, the adopted methodology involves an empirical study of the Brazilian jurisprudence. As a conclusion, it follows that the public hearings convened by the Brazilian Supreme Court do not correspond, in practice, to the role assigned to them by the Congress since they do not serve properly to epistemic interests. The public hearings not only do not legitimate democratically the decisions, but also, do not properly clarify technical issues.
Abstract: The importance of this study is to understand how Indonesian military court asserts its jurisdiction over military members who commit general crimes within the Indonesian military judiciary system in comparison to other countries. This research employs a normative-juridical approach in combination with historical and comparative-juridical approaches. The research specification is analytical-descriptive in nature, i.e. describing or outlining the principles, basic concepts, and norms related to military judiciary system, which are further analyzed within the context of implementation and as the inputs for military justice regulation under the Indonesian legal system. Main data used in this research are secondary data, including primary, secondary and tertiary legal sources. The research focuses on secondary data, while primary data are supplementary in nature. The validity of data is checked using multi-methods commonly known as triangulation, i.e. to reflect the efforts to gain an in-depth understanding of phenomena being studied. Here, the military element is kept intact in the judiciary process with due observance of the Military Criminal Justice System and the Military Command Development Principle. The Indonesian military judiciary jurisdiction over military members committing general crimes is based on national legal system and global development while taking into account the structure, composition and position of military forces within the state structure. Jurisdiction is formulated by setting forth the substantive norm of crimes that are military in nature. At the level of adjudication jurisdiction, the military court has a jurisdiction to adjudicate military personnel who commit general offences. At the level of execution jurisdiction, the military court has a jurisdiction to execute the sentence against military members who have been convicted with a final and binding judgement. Military court's jurisdiction needs to be expanded when the country is in the state of war.
Abstract: Effect of alloying on the microstructure and mechanical properties of heat-resisting duplex stainless steel (DSS) for Mg production was investigated in this study. 25Cr-8Ni based DSS’s were cast into rectangular ingots of which the dimension was 350×350×100 mm3 . Nitrogen and Yttrium were added in the range within 0.3 in weight percent. Phase equilibrium was calculated using the FactSage®, thermodynamic software. Hot exposure, high temperature tensile and compression tests were conducted on the ingots at 1230oC, which is operation temperature employed for Mg production by Silico-thermic reduction. The steel with N and Y showed much higher strength than 310S alloy in both tensile and compression tests. By thermal exposition at 1230oC for 200 hrs, hardness of DSS containing N and Y was found to increase. Hot workability of the heat-resisting DSS was evaluated by employing hot rolling at 1230 oC. Hot shortness was observed in the ingot with N and found to disappear after addition of Y.
Abstract: We introduce a new model called the Marshall-Olkin Rayleigh distribution which extends the Rayleigh distribution using Marshall-Olkin transformation and has increasing and decreasing shapes for the hazard rate function. Various structural properties of the new distribution are derived including explicit expressions for the moments, generating and quantile function, some entropy measures, and order statistics are presented. The model parameters are estimated by the method of maximum likelihood and the observed information matrix is determined. The potentiality of the new model is illustrated by means of a simulation study.
Abstract: The world crude oil demand is projected to rise to 108.5 million bbl/d by the year 2035. With reserves estimated at 869 billion tonnes worldwide, coal remains an abundant resource. The aim of this work was to produce a high value hydrocarbon liquid product using a Direct Coal Liquefaction (DCL) process at, relatively mild operating conditions. Via hydrogenation, the temperature-staged approach was investigated in a dual reactor lab-scale pilot plant facility. The objectives included maximising thermal dissolution of the coal in the presence of tetralin as the hydrogen donor solvent in the first stage with 2:1 and 3:1 solvent: coal ratios. Subsequently, in the second stage, hydrogen saturation, in particular, hydrodesulphurization (HDS) performance was assessed. Two commercial hydrotreating catalysts were investigated viz. NickelMolybdenum (Ni-Mo) and Cobalt-Molybdenum (Co-Mo). GC-MS results identified 77 compounds and various functional groups present in the first and second stage liquid product. In the first stage 3:1 ratios and liquid product yields catalysed by magnetite were favoured. The second stage product distribution showed an increase in the BTX (Benzene, Toluene, Xylene) quality of the liquid product, branched chain alkanes and a reduction in the sulphur concentration. As an HDS performer and selectivity to the production of long and branched chain alkanes, Ni-Mo had an improved performance over Co-Mo. Co-Mo is selective to a higher concentration of cyclohexane. For 16 days on stream each, Ni-Mo had a higher activity than Co-Mo. The potential to cover the demand for low–sulphur, crude diesel and solvents from the production of high value hydrocarbon liquid in the said process, is thus demonstrated.
Abstract: In this study, we demonstrate a high-resolution
refractive index sensor based on a Magnetic Photonic Crystal (MPC)
composed of a triangular lattice array of air holes embedded in Si
matrix. A microcavity is created by changing the radius of an air hole
in the middle of the photonic crystal. The cavity filled with gyrotropic
materials can serve as a refractive index sensor. The shift of the
resonant frequency of the sensor is obtained numerically using finite
difference time domain method under different ambient conditions
having refractive index from n = 1.0 to n = 1.1. The numerical results
show that a tiny change in refractive index of Δn = 0.0001 is
distinguishable. In addition, the spectral response of the MPC sensor is
studied while an external magnetic field is present. The results show
that the MPC sensor exhibits a dramatic improvement in resolution.
Abstract: In the past few years, high consumption of soft drinks
has attracted negative attention world-wide due to its possible
adverse effects, leading the health conscious people to find
alternative nutraceutical or herbal health drinks. In the present study,
a nutraceutical soft drink was developed utilizing some easily
available and well known traditional herbs having nutritional
potential. The key ingredients were selected as bael, amla, lemon
juice, ashwagandha and poppy seeds based on their household routine
use in the summer with proven refreshing, cooling and energetic
feeling since ages. After several trials made, the final composition of
nutraceutical summer soft drink was selected as most suitable
combination based on the taste, physicochemical, microbial and
organoleptic point of view. The physicochemical analysis of the
prepared drink found to contain optimum level of titratable acidity,
total soluble solids and pH which were in accordance of the
commercial recommendations. There were no bacterial colonies
found in the product therefore found within limits. During the nine
point’s hedonic scale sensory evaluation, the drink was strongly liked
for colour, taste, flavour and texture. The formulation was found to
contain flavonoids (80mg/100ml), phenolics (103mg/100ml), vitamin
C (250mg/100ml) and has antioxidant potential (75.52%) apart from
providing several other essential vitamins, minerals and healthy
components. The developed nutraceutical drink provides an
economical and feasible option for the consumers with very good
taste combined with potential health benefits. The present drink is
potentially capable to replace the synthetic soft drinks available in the
market.
Abstract: In this paper, we present a quantum statistical
mechanical formulation from our recently analytical expressions for
partial-wave transition matrix of a three-particle system. We report
the quantum reactive cross sections for three-body scattering
processes 1+(2,3)→1+(2,3) as well as recombination
1+(2,3)→1+(3,1) between one atom and a weakly-bound dimer. The
analytical expressions of three-particle transition matrices and their
corresponding cross-sections were obtained from the threedimensional
Faddeev equations subjected to the rank-two non-local
separable potentials of the generalized Yamaguchi form. The
equilibrium quantum statistical mechanical properties such partition
function and equation of state as well as non-equilibrium quantum
statistical properties such as transport cross-sections and their
corresponding transport collision integrals were formulated
analytically. This leads to obtain the transport properties, such as
viscosity and diffusion coefficient of a moderate dense gas.
Abstract: The seriously damaged structures during earthquakes
show the need and importance of design of reinforced concrete
structures with high ductility. Reinforced concrete beam-column
joints have an important function in all structures. Under seismic
excitation, the beam column joint region is subjected to horizontal
and vertical shear forces whose magnitude is many times higher than
the adjacent beam and column. Strength and ductility of structures
depends mainly on proper detailing of the reinforcement in beamcolumn
joints and the old structures were found ductility deficient.
DSP materials are obtained by using high quantities of super
plasticizers and high volumes of micro silica. In the case of High
Performance Densified Small Particle Concrete (HPDSPC), since
concrete is dense even at the micro-structure level, tensile strain
would be much higher than that of the conventional SFRC, SIFCON
& SIMCON. This in turn will improve cracking behaviour, ductility
and energy absorption capacity of composites in addition to
durability. The fine fibers used in our mix are 0.3mm diameter and 10
mm which can be easily placed with high percentage. These fibers
easily transfer stresses and act as a composite concrete unit to take up
extremely high loads with high compressive strength. HPDSPC
placed in the beam column joints helps in safety of human life due to
prolonged failure.
Abstract: The first laboratory synthesis of hard materials such as
diamond proceeded to attack of developing materials with high
hardness to compete diamond. Boron rich solids are good candidates
owing to their short interatomic bond lengths and strong covalent
character. Boron containing hard material was synthesized by modifiedmicrowave
method under nitrogen atmosphere by using a fuel
(glycine or urea), amorphous boron and/or boric acid in appropriate
molar ratio. Characterizations were done by x-ray diffraction (XRD),
Fourier transform infrared (FTIR) spectroscopy, scanning electron
microscopy/energy dispersive analyze (SEM/EDS), thermo
gravimetric/differential thermal analysis (TG/DTA).
Abstract: A teeming set of doctors that graduated from various
universities within and outside Nigeria with the hope of practicing in
the country, has their hope shattered because of poor financing, lack
of medical equipments and a very weak healthcare systems. Such
hydra headed challenges, allows room for quackery which
increasingly contributes to the cause of mortality in Nigeria. With a
view of reversing the challenges of healthcare delivery and financing
in Nigeria, African Health Market for Equity (AHME), a project
funded by the Bill and Melinda Gates foundation [With contribution
from Department For International Development (DFID)] and
currently implemented in three African Countries (Nigeria, Kenya
and Ghana) over a Five (5) year period supports the healthcare sector
via Medical credit fund (MCF). The study examines the impact of
credit policy and medical credit funding on Nigerian health market.
Ordinary least square analysis, correlation and granger causality tests
were employed to measure the extent to which the Nigerian
healthcare market has been influenced. Medical credit fund
significantly and positively influenced average monthly turnover of
private healthcare providers and Commercial bank’s lending rate had
a weak relationship with access to credit/approved loans (13.46%).
The programme has so far made 13.91% progress, which is very
poor, considering the minimum targeted private health care providers
(437.6) and expected number of loan approvals (180.4) for the two
years. Medical credit policy in Nigeria should be revised to include
private healthcare providers in rural area for more positive impact
and increased returns. Good brand advert and sensitization of the
programme to stakeholders and health pressure group, and an
extension of the programme beyond five years is necessary to better
address the issues raised in the study.
Abstract: During welding or flame cutting of metals, the
prediction of heat affected zone (HAZ) is critical. There is need to
develop a simple mathematical model to calculate the temperature
variation in HAZ and derivative analysis can be used for this purpose.
This study presents analytical solution for heat transfer through
conduction in mild steel plate. The homogeneous and nonhomogeneous
boundary conditions are single variables. The full field
analytical solutions of temperature measurement, subjected to local
heating source, are derived first by method of separation of variables
followed with the experimental visualization using infrared imaging.
Based on the present work, it is suggested that appropriate heat input
characteristics controls the temperature distribution in and around
HAZ.
Abstract: The end of the line controls of the finished products in
the automotive industry is important. The control that has been
conducted with the manual methods for the sliding doors tracks is not
sufficient and faulty products cannot be identified. As a result, the
customer has the faulty products. In the scope of this study, the
design criteria of the PLC integrated modular end of line control unit
has been examined, designed and manufactured to make the control
of the 10 different track profile to 2 different vehicles with an
objective to minimize the salvage costs by obtaining more sensitive,
certain and accurate measurement results. In the study that started
with literature and patent review, the design inputs have been
specified, the technical concept has been developed, computer
supported mechanic design, control system and automation design,
design review and design improvement have been made. Laser
analog sensors at high sensitivity, probes and modular blocks have
been used in the unit. The measurement has been conducted in the
system and it is observed that measurement results are more sensitive
than the previous methods that we use.
Abstract: A novel Active Flap System (AFS) has been developed
at DTU Wind Energy, as a result of a 3-year R&D project following
almost 10 years of innovative research in this field. The full scale AFS
comprises an active deformable trailing edge has been tested at the
unique rotating test facility at the Risø Campus of DTU Wind Energy
in Denmark. The design and instrumentation of the wing section and
the AFS are described. The general description and objectives of the
rotating test rig at the Risø campus of DTU are presented, along
with an overview of sensors on the setup and the test cases. The
post-processing of data is discussed and results of steady, flap step
and azimuth control flap cases are presented.
Abstract: The aim of this study was to investigate the
photocatalytic activity of polycrystalline phases of bismuth tungstate
of formula Bi2WO6. Polycrystalline samples were elaborated using a
coprecipitation technique followed by a calcination process at
different temperatures (300, 400, 600 and 900°C). The obtained
polycrystalline phases have been characterized by X-ray diffraction
(XRD), scanning electron microscopy (SEM), and transmission
electron microscopy (TEM). Crystal cell parameters and cell volume
depend on elaboration temperature. High-resolution electron
microscopy images and image simulations, associated with X-ray
diffraction data, allowed confirming the lattices and space groups
Pca21. The photocatalytic activity of the as-prepared samples was
studied by irradiating aqueous solutions of Rhodamine B, associated
with Bi2WO6 additives having variable crystallite sizes. The
photocatalytic activity of such bismuth tungstates increased as the
crystallite sizes decreased. The high specific area of the
photocatalytic particles obtained at 300°C seems to condition the
degradation kinetics of RhB.
Abstract: In this paper, temperature extremes are forecast by
employing the block maxima method of the Generalized extreme
value(GEV) distribution to analyse temperature data from the
Cameroon Development Corporation (C.D.C). By considering two sets
of data (Raw data and simulated data) and two (stationary and
non-stationary) models of the GEV distribution, return levels analysis
is carried out and it was found that in the stationary model, the
return values are constant over time with the raw data while in the
simulated data, the return values show an increasing trend but with
an upper bound. In the non-stationary model, the return levels of
both the raw data and simulated data show an increasing trend but
with an upper bound. This clearly shows that temperatures in the
tropics even-though show a sign of increasing in the future, there
is a maximum temperature at which there is no exceedence. The
results of this paper are very vital in Agricultural and Environmental
research.
Abstract: Currently, planners try to have more green travel
options to decrease economic, social and environmental problems.
Therefore, this study tries to find significant urban travel factors to be
used to increase the usage of alternative urban travel modes. This
paper attempts to identify the relationship between prominent urban
mobility indicators and daily trips by public transport in 30 cities
from various parts of the world. Different travel modes,
infrastructures and cost indicators were evaluated in this research as
mobility indicators. The results of multi-linear regression analysis
indicate that there is a significant relationship between mobility
indicators and the daily usage of public transport.