Abstract: The incidence of mechanical fracture of an
automobile piston rings prompted development of fracture analysis
method on this case. The three rings (two compression rings and one
oil ring) were smashed into several parts during the power-test (after
manufacturing the engine) causing piston and liner to be damaged.
The radial and oblique cracking happened on the failed piston rings.
The aim of the fracture mechanics simulations presented in this paper
was the calculation of particular effective fracture mechanics
parameters, such as J-integrals and stress intensity factors. Crack
propagation angles were calculated as well. Two-dimensional
fracture analysis of the first compression ring has been developed in
this paper using ABAQUS CAE6.5-1 software. Moreover, SEM
fractography was developed on fracture surfaces and is discussed in
this paper. Results of numerical calculations constitute the basis for
further research on real object.
Abstract: In this paper, a Biochemical Methane Potential (BMP)
test provides a measure of the energy production potential from codigestion
between the frozen seafood wastewater and the decanter
cake. The experiments were conducted in laboratory-scale. The
suitable ratio of the frozen seafood wastewater and the decanter cake
was observed in the BMP test. The ratio of the co-digestion between
the frozen seafood wastewater and the decanter cake has impacts on
the biogas production and energy production potential. The best
performance for energy production potential using BMP test
observed from the 180 ml of the frozen seafood wastewater and 10 g
of the decanter cake ratio. This ratio provided the maximum methane
production at 0.351 l CH4/g TCODremoval. The removal efficiencies
are 76.18%, 83.55%, 43.16% and 56.76% at TCOD, SCOD, TS and
VS, respectively. The result can be concluded that the decanter cake
can improve the energy production potential of the frozen seafood
wastewater. The energy provides from co-digestion between frozen
seafood wastewater and decanter cake approximately 19x109
MJ/year in Thailand.
Abstract: The malfunction of thermal protection system (TPS) caused by aerodynamic heating is a latent trouble to aircraft structure safety. Accurately predicting the structure temperature field is quite important for the TPS design of hypersonic vehicle. Since Thornton’s work in 1988, the coupled method of aerodynamic heating and heat transfer has developed rapidly. However, little attention has been paid to the influence of structural deformation on aerodynamic heating and structural temperature field. In the flight, especially the long-endurance flight, the structural deformation, caused by the aerodynamic heating and temperature rise, has a direct impact on the aerodynamic heating and structural temperature field. Thus, the coupled interaction cannot be neglected. In this paper, based on the method of static aero-thermo-elasticity, considering the influence of aero-thermo-elasticity deformation, the aerodynamic heating and heat transfer coupled results of hypersonic vehicle wing model were calculated. The results show that, for the low-curvature region, such as fuselage or center-section wing, structure deformation has little effect on temperature field. However, for the stagnation region with high curvature, the coupled effect is not negligible. Thus, it is quite important for the structure temperature prediction to take into account the effect of elastic deformation. This work has laid a solid foundation for improving the prediction accuracy of the temperature distribution of aircraft structures and the evaluation capacity of structural performance.
Abstract: In recent years, there has been an increasing interest
toward the use of bovine genotyped embryos for commercial embryo
transfer programs. Biopsy of a few cells in morulla stage is essential
for preimplantation genetic diagnosis (PGD). Low amount of DNA
have limited performing the several molecular analyses within PGD
analyses. Whole genome amplification (WGA) promises to eliminate
this problem. We evaluated the possibility and performance of an
improved primer extension preamplification (I-PEP) method with a
range of starting bovine genomic DNA from 1-8 cells into the WGA
reaction. We optimized a short and simple I-PEP (ssI-PEP) procedure
(~3h). This optimized WGA method was assessed by 6 loci specific
polymerase chain reactions (PCRs), included restriction fragments
length polymorphism (RFLP). Optimized WGA procedure possesses
enough sensitivity for molecular genetic analyses through the few
input cells. This is a new era for generating characterized bovine
embryos in preimplantation stage.
Abstract: Electrical distribution systems are incurring large losses as the loads are wide spread, inadequate reactive power compensation facilities and their improper control. A comprehensive static VAR compensator consisting of capacitor bank in five binary sequential steps in conjunction with a thyristor controlled reactor of smallest step size is employed in the investigative work. The work deals with the performance evaluation through analytical studies and practical implementation on an existing system. A fast acting error adaptive controller is developed suitable both for contactor and thyristor switched capacitors. The switching operations achieved are transient free, practically no need to provide inrush current limiting reactors, TCR size minimum providing small percentages of nontriplen harmonics, facilitates stepless variation of reactive power depending on load requirement so as maintain power factor near unity always. It is elegant, closed loop microcontroller system having the features of self regulation in adaptive mode for automatic adjustment. It is successfully tested on a distribution transformer of three phase 50 Hz, Dy11, 11KV/440V, 125 KVA capacity and the functional feasibility and technical soundness are established. The controller developed is new, adaptable to both LT & HT systems and practically established to be giving reliable performance.
Abstract: Eutrophication of surface water is one of the most
widespread environmental problems at present. Large number of
pilgrims and tourists visit sacred artificial tank known as “Brahma
Sarover” located at Kurukshetra, India to take holy dip and perform
religious ceremonies. The sources of pollutants include impurities in
feed water, mass bathing, religious offerings and windblown
particulate matter. Studies so far have focused mainly on assessing
water quality for bathing purpose by using physico-chemical and
bacteriological parameters. No effort has been made to assess nutrient
concentration and trophic status of the tank to take more appropriate
measures for improving water quality on long term basis. In the
present study, total nitrogen, total phosphorous and chlorophyll a
measurements have been done to assess the nutrient level and trophic
status of the tank. The results show presence of high concentration of
nutrients and Chlorophyll a indicating mesotrophic and eutrophic
state of the tank. Phosphorous has been observed as limiting nutrient
in the tank water.
Abstract: The mixed oxide nuclear fuel (MOX) of U and Pu contains several percent of fission products and minor actinides, such as neptunium, americium and curium. It is important to determine accurately the decay heat from Curium isotopes as they contribute significantly in the MOX fuel. This heat generation can cause samples to melt very quickly if excessive quantities of curium are present. In the present paper, we introduce a new approach that can predict the decay heat from curium isotopes. This work is a part of the project funded by King Abdulaziz City of Science and Technology (KASCT), Long-Term Comprehensive National Plan for Science, Technology and Innovations, and take place in King Abdulaziz University (KAU), Saudi Arabia. The approach is based on the numerical solution of coupled linear differential equations that describe decays and buildups of many nuclides to calculate the decay heat produced after shutdown. Results show the consistency and reliability of the approach applied.
Abstract: This paper proposes a new technique for improving
the efficiency of software testing, which is based on a conventional
attempt to reduce test cases that have to be tested for any given
software. The approach utilizes the advantage of Regression Testing
where fewer test cases would lessen time consumption of the testing
as a whole. The technique also offers a means to perform test case
generation automatically. Compared to one of the techniques in the
literature where the tester has no option but to perform the test case
generation manually, the proposed technique provides a better
option. As for the test cases reduction, the technique uses simple
algebraic conditions to assign fixed values to variables (Maximum,
minimum and constant variables). By doing this, the variables values
would be limited within a definite range, resulting in fewer numbers
of possible test cases to process. The technique can also be used in
program loops and arrays.
Abstract: This article concerns the presentation of an integrated
method for detection of steganographic content embedded by new
unknown programs. The method is based on data mining and
aggregated hypothesis testing. The article contains the theoretical
basics used to deploy the proposed detection system and the
description of improvement proposed for the basic system idea.
Further main results of experiments and implementation details are
collected and described. Finally example results of the tests are
presented.
Abstract: The autonomous mobile robot was designed and implemented which was capable of navigating in the industrial environments and did a job of picking objects from variable height and delivering it to another location following a predefined trajectory. In developing country like Bangladesh industrial robotics is not very prevalent yet, due to the high installation cost. The objective of this project was to develop an autonomous mobile robot for industrial application using the available resources in the local market at lower manufacturing cost. The mechanical system of the robot was comprised of locomotion, gripping and elevation system. Grippers were designed to grip objects of a predefined shape. Cartesian elevation system was designed for vertical movement of the gripper. PIC18F452 microcontroller was the brain of the control system. The prototype autonomous robot was fabricated for relatively lower load than the industry and the performance was tested in a virtual industrial environment created within the laboratory to realize the effectiveness.
Abstract: The aim of this study was to investigate the effects of
supplementing the diluent of roosters' semen with different levels of
olive oil on motility, viability, morphology and acrosome integrity of
chicken spermatozoa after in vitro storage for up to 72 h. Semen was
collected from 60 White Layer males (62 wk of age) kept in
separated floor pens and randomly divided into six treatment groups
(10 males in each group). Experimental groups were as follows: T1
:fresh semen, T2 : semen extended 1:1 with Al – Daraji 2 diluent
(AD2D) alone, T3 – T6 :semen samples extended 1:1 with AD2D
supplemented with 2 ml, 4 ml, 6 ml or 8 ml of olive oil / 100 ml of
diluent, respectively. Semen samples were then stored at 5 °C for 24
h, 48 h or 72 h. There was a clear influence of diluent
supplementation with olive oil on the spermatozoa motility profile;
olive oil groups (T3, T4, T5 and T6) recorded the highest scores of
mass activity and individual motility during all storage periods
compared to T1 and T2 groups. In addition, the inclusion of olive oil
into semen diluent (T3, T4, T5 and T6) gave significantly higher
percentages of viable spermatozoa, normal morphologically
spermatozoa and intact acrosomes irrespective of storage period.
These results clearly show that supplementation the diluent of
roosters' semen with olive oil can improve semen quality when
semen samples in vitro stored at 5 °C for up to 72 h.
Abstract: The amplitude response of infrared (IR) sensors
depends on the reflectance properties of the target. Therefore, in
order to use IR sensor for measuring distances accurately, prior
knowledge of the surface must be known. This paper describes the
Phong Illumination Model for determining the properties of a surface
and subsequently calculating the distance to the surface. The angular
position of the IR sensor is computed as normal to the surface for
simplifying the calculation. Ultrasonic (US) sensor can provide the
initial information on distance to obtain the parameters for this
method. In addition, the experimental results obtained by using
LabView are discussed. More care should be taken when placing the
objects from the sensors during acquiring data since the small change
in angle could show very different distance than the actual one.
Since stereo camera vision systems do not perform well under some
environmental conditions such as plain wall, glass surfaces, or poor
lighting conditions, the IR and US sensors can be used additionally to
improve the overall vision systems of mobile robots.
Abstract: In this paper, an image adaptive, invisible digital
watermarking algorithm with Orthogonal Polynomials based
Transformation (OPT) is proposed, for copyright protection of digital
images. The proposed algorithm utilizes a visual model to determine
the watermarking strength necessary to invisibly embed the
watermark in the mid frequency AC coefficients of the cover image,
chosen with a secret key. The visual model is designed to generate a
Just Noticeable Distortion mask (JND) by analyzing the low level
image characteristics such as textures, edges and luminance of the
cover image in the orthogonal polynomials based transformation
domain. Since the secret key is required for both embedding and
extraction of watermark, it is not possible for an unauthorized user to
extract the embedded watermark. The proposed scheme is robust to
common image processing distortions like filtering, JPEG
compression and additive noise. Experimental results show that the
quality of OPT domain watermarked images is better than its DCT
counterpart.
Abstract: Image mosaicing is a technique that permits to enlarge the field of view of a camera. For instance, it is employed to achieve panoramas with common cameras or even in scientific applications, to achieve the image of a whole culture in microscopical imaging. Usually, a mosaic of cell cultures is achieved through using automated microscopes. However, this is often performed in batch, through CPU intensive minimization algorithms. In addition, live stem cells are studied in phase contrast, showing a low contrast that cannot be improved further. We present a method to study the flat field from live stem cells images even in case of 100% confluence, this permitting to build accurate mosaics on-line using high performance algorithms.
Abstract: Nowadays, the performance required for concrete
structures is more complicated and diversified. Self-compacting
concrete is a fluid mixture suitable for placing in structures with
congested reinforcement without vibration. Self-compacting concrete
development must ensure a good balance between deformability and
stability. Also, compatibility is affected by the characteristics of
materials and the mix proportions; it becomes necessary to evolve a
procedure for mix design of SCC.
This paper presents an experimental procedure for the design of
self-compacting concrete mixes with different water-cement ratios
(w/c) and other constant ratios by local materials. The test results for
acceptance characteristics of self-compacting concrete such as slump
flow, V-funnel and L-Box are presented. Further, compressive
strength, tensile strength and modulus of elasticity of specimens were
also determined and results are included here
Abstract: In this paper a hybrid technique of Genetic Algorithm
and Simulated Annealing (HGASA) is applied for Fractal Image
Compression (FIC). With the help of this hybrid evolutionary
algorithm effort is made to reduce the search complexity of matching
between range block and domain block. The concept of Simulated
Annealing (SA) is incorporated into Genetic Algorithm (GA) in order
to avoid pre-mature convergence of the strings. One of the image
compression techniques in the spatial domain is Fractal Image
Compression but the main drawback of FIC is that it involves more
computational time due to global search. In order to improve the
computational time along with acceptable quality of the decoded
image, HGASA technique has been proposed. Experimental results
show that the proposed HGASA is a better method than GA in terms
of PSNR for Fractal image Compression.
Abstract: In this paper, a numerical study has been made to
analyze the transient 2-D flows of a viscous incompressible fluid
through channels with forward or backward constriction. Problems
addressed include flow through sudden contraction and sudden
expansion channel geometries with rounded and increasingly sharp
reentrant corner. In both the cases, numerical results are presented for
the separation and reattachment points, streamlines, vorticity and
flow patterns. A fourth order accurate compact scheme has been
employed to efficiently capture steady state solutions of the
governing equations. It appears from our study that sharpness of the
throat in the channel is one of the important parameters to control the
strength and size of the separation zone without modifying the
general flow patterns. The comparison between the two cases shows
that the upstream geometry plays a significant role on vortex growth
dynamics.
Abstract: Currently, there is no database or local norms for the
physical performance of Malaysian rugby players. This database or
norms are vital for Malaysian-s sports development as programs can
be setup to improve the current status. This pilot study was
conducted to evaluate the status of our semi professional rugby
players. The rugby players were randomly selected from the
Malaysian National team and several clubs in the Klang valley, Kuala
Lumpur Malaysia. 54 male rugby players (Age: 24.41 ± 4.06 years)
were selected for this pilot study. Height, bodyweight, percentage
body fat and body mass index (BMI) and several other physical tests
were performed. Results from the BLEEP test revealed an average of
level 9, shuttle 2 for the players. Interestingly, forwards were taller,
heavier, and had lower maximal aerobic power than backs in the
same team. In conclusion, the physical characteristics of the rugby
players were much lower when compared to international players
from other countries. From this pilot study, the physical performance
of the Malaysian team must be improved in order to further develop
the sports.
Abstract: Considering today-s increasing speed of change,
radical and innovative improvement - Kaikaku, is a necessity parallel
to continuous incremental improvement - Kaizen, especially for
SME-s in order to attain the competitive edge needed to be profitable.
During 2011, a qualitative single case study with the objective of
realizing a kaikaku in production has been conducted. The case study
was run as a one year project using a collaborative approach
including both researchers and company representatives. The case
study was conducted with the purpose of gaining further knowledge
about kaikaku realization as well as its implications. The empirical
results provide insights about the great productivity results achieved
by applying a specific kaikaku realization approach. However, it also
sheds light on the difficulty and contradiction of combining
innovation management and production system development.
Abstract: Along with the basic features of students\' culture
information, with its widely usage oriented on implementation of the
new information technologies in educational process that determines
the search for ways of pointing to the similarity of interdisciplinary
connections content, aims and objectives of the study. In this regard,
the article questions about students\' information culture, and also
presented information about the aims and objectives of the
information culture process among students. In the formation of a
professional interest in relevant information, which is an opportunity
to assist in informing the professional activities of the essence of
effective use of interactive methods and innovative technologies in
the learning process. The result of the experiment proves the
effectiveness of the information culture process of students in
training the system of higher education based on the credit
technology. The main purpose of this paper is a comprehensive
review of students\' information culture.