Abstract: This paper presents an application of power line
carrier (PLC) for electrical power telemetering. This system has a
special capability of transmitting the measured values to a centralized
computer via power lines. The PLC modem as a passive high-pass
filter is designed for transmitting and receiving information. Its
function is to send the information carrier together with transmitted
data by superimposing it on the 50 Hz power frequency signal. A
microcontroller is employed to function as the main processing of the
modem. It is programmed for PLC control and interfacing with other
devices. Each power meter, connected via a PLC modem, is assigned
with a unique identification number (address) for distinguishing each
device from one another.
Abstract: Two seperate experiments by barley and alfalfa were
conducted to a 2×8 factorial completely randomised design, with four
replicates. Factors were inoculation (M) with Gomus mosseae or uninoculation
(M0) and seven levels of contaminants (Co, Cd, Pb and
combinations) plus an uncontaminated control treatment (C). Heavy
metals in plant tissues and soil were quantified by Inductively
Coupled Plasma Optical Emission Spectrometer (ICP-OES) (Variant-
Liberty 150AX Turbo). Phytoextraction coefficient of contaminants
calculated by concentration of heavy metals in the shoot (mgkg-1) /
concentration of heavy metals in soil (mgkg-1). In the barley, the
highest rate of phytoextraction coefficient of Pb, Cd and Co was in
M0Pb, M0PbCoCd and MCo, respectively (P
Abstract: Reinforced concrete stair slabs with mid landings i.e.
Dog-legged shaped are conventionally designed as per specifications
of standard codes of practices which guide about the effective span
according to the varying support conditions. Presently, the behavior
of such slabs has been investigated using Finite Element method. A
single flight stair slab with landings on both sides and supported at
ends on wall, and a multi flight stair slab with landings and six
different support arrangements have been analyzed. The results
obtained for stresses, strains and deflections are used to describe the
behavior of such stair slabs, including locations of critical moments
and deflections. Values of critical moments obtained by F.E. analysis
have also have been compared with that obtained from conventional
analysis. Analytical results show that the moments are also critical
near the kinks i.e. junction of mid-landing and inclined waist slab.
This change in the behavior of dog-legged stair slab may be due to
continuity of the material in transverse direction in two landings
adjoining the waist slab, hence additional stiffness achieved. This
change in the behavior is generally not taken care of in conventional
method of design.
Abstract: Designing modern machine tools is a complex task. A
simulation tool to aid the design work, a virtual machine, has
therefore been developed in earlier work. The virtual machine
considers the interaction between the mechanics of the machine
(including structural flexibility) and the control system. This paper
exemplifies the usefulness of the virtual machine as a tool for product
development. An optimisation study is conducted aiming at
improving the existing design of a machine tool regarding weight and
manufacturing accuracy at maintained manufacturing speed. The
problem can be categorised as constrained multidisciplinary multiobjective
multivariable optimisation. Parameters of the control and
geometric quantities of the machine are used as design variables. This
results in a mix of continuous and discrete variables and an
optimisation approach using a genetic algorithm is therefore
deployed. The accuracy objective is evaluated according to
international standards. The complete systems model shows nondeterministic
behaviour. A strategy to handle this based on statistical
analysis is suggested. The weight of the main moving parts is reduced
by more than 30 per cent and the manufacturing accuracy is
improvement by more than 60 per cent compared to the original
design, with no reduction in manufacturing speed. It is also shown
that interaction effects exist between the mechanics and the control,
i.e. this improvement would most likely not been possible with a
conventional sequential design approach within the same time, cost
and general resource frame. This indicates the potential of the virtual
machine concept for contributing to improved efficiency of both
complex products and the development process for such products.
Companies incorporating such advanced simulation tools in their
product development could thus improve its own competitiveness as
well as contribute to improved resource efficiency of society at large.
Abstract: Unlike general-purpose processors, digital signal
processors (DSP processors) are strongly application-dependent. To
meet the needs for diverse applications, a wide variety of DSP
processors based on different architectures ranging from the
traditional to VLIW have been introduced to the market over the
years. The functionality, performance, and cost of these processors
vary over a wide range. In order to select a processor that meets the
design criteria for an application, processor performance is usually
the major concern for digital signal processing (DSP) application
developers. Performance data are also essential for the designers of
DSP processors to improve their design. Consequently, several DSP
performance benchmarks have been proposed over the past decade or
so. However, none of these benchmarks seem to have included recent
new DSP applications.
In this paper, we use a new benchmark that we recently developed
to compare the performance of popular DSP processors from Texas
Instruments and StarCore. The new benchmark is based on the
Selectable Mode Vocoder (SMV), a speech-coding program from the
recent third generation (3G) wireless voice applications. All
benchmark kernels are compiled by the compilers of the respective
DSP processors and run on their simulators. Weighted arithmetic
mean of clock cycles and arithmetic mean of code size are used to
compare the performance of five DSP processors.
In addition, we studied how the performance of a processor is
affected by code structure, features of processor architecture and
optimization of compiler. The extensive experimental data gathered,
analyzed, and presented in this paper should be helpful for DSP
processor and compiler designers to meet their specific design goals.
Abstract: Shipping comb is mounted on Head Stack Assembly
(HSA) to prevent collision of the heads, maintain the gap between
suspensions and protect HSA tips from unintentional contact
damaged in the manufacturing process. Failure analysis of shipping
comb in hard disk drive production processes is proposed .Field
observations were performed to determine the fatal areas on shipping
comb and their failure fraction. Root cause failure analysis (RCFA) is
applied to specify the failure causes subjected to various loading
conditions. For reliability improvement, failure mode and effects
analysis (FMEA) procedure to evaluate the risk priority is performed.
Consequently, the more suitable information design criterions were
obtained.
Abstract: Educating effective architect designers is an important
goal of architectural education. But what contributes to students-
performance, and to critical and creative thinking in architectural
design education? Besides teaching architecture students how to
understand logical arguments, eliminate the inadequate solutions and
focus on the correct ones, it is also crucial to teach students how to
focus on exploring ideas and the alternative solutions and seeking for
other right answers rather than one. This paper focuses on the
enhancing architectural design education and may provide
implications for enhancing teaching design.
Abstract: Radio frequency identification (RFID) applications have grown rapidly in many industries, especially in indoor location identification. The advantage of using received signal strength indicator (RSSI) values as an indoor location measurement method is a cost-effective approach without installing extra hardware. Because the accuracy of many positioning schemes using RSSI values is limited by interference factors and the environment, thus it is challenging to use RFID location techniques based on integrating positioning algorithm design. This study proposes the location estimation approach and analyzes a scheme relying on RSSI values to minimize location errors. In addition, this paper examines different factors that affect location accuracy by integrating the backpropagation neural network (BPN) with the LANDMARC algorithm in a training phase and an online phase. First, the training phase computes coordinates obtained from the LANDMARC algorithm, which uses RSSI values and the real coordinates of reference tags as training data for constructing an appropriate BPN architecture and training length. Second, in the online phase, the LANDMARC algorithm calculates the coordinates of tracking tags, which are then used as BPN inputs to obtain location estimates. The results show that the proposed scheme can estimate locations more accurately compared to LANDMARC without extra devices.
Abstract: Wikis are considered to be part of Web 2.0
technologies that potentially support collaborative learning and
writing. Wikis provide opportunities for multiple users to work on
the same document simultaneously. Most wikis have also a page for
written group discussion. Nevertheless, wikis may be used in
different ways depending on the pedagogy being used, and the
constraints imposed by the course design. This work explores
students- uses of wiki in teacher education. The analysis is based on a
taxonomy for classifying students- activities and actions carried out
on the wiki. The article also discusses the implications for using
wikis as collaborative writing tools in teacher education.
Abstract: The purpose of this research is to develop a security model for voice eavesdropping protection over digital networks. The proposed model provides an encryption scheme and a personal secret key exchange between communicating parties, a so-called voice data transformation system, resulting in a real-privacy conversation. The operation of this system comprises two main steps as follows: The first one is the personal secret key exchange for using the keys in the data encryption process during conversation. The key owner could freely make his/her choice in key selection, so it is recommended that one should exchange a different key for a different conversational party, and record the key for each case into the memory provided in the client device. The next step is to set and record another personal option of encryption, either taking all frames or just partial frames, so-called the figure of 1:M. Using different personal secret keys and different sets of 1:M to different parties without the intervention of the service operator, would result in posing quite a big problem for any eavesdroppers who attempt to discover the key used during the conversation, especially in a short period of time. Thus, it is quite safe and effective to protect the case of voice eavesdropping. The results of the implementation indicate that the system can perform its function accurately as designed. In this regard, the proposed system is suitable for effective use in voice eavesdropping protection over digital networks, without any requirements to change presently existing network systems, mobile phone network and VoIP, for instance.
Abstract: This paper presents a new stable robust adaptive controller and observer design for a class of nonlinear systems that contain i. Coupling of unmeasured states and unknown parameters ii. Unknown dead zone at the system actuator. The system is firstly cast into a modified form in which the observer and parameter estimation become feasible. Then a stable robust adaptive controller, state observer, parameter update laws are derived that would provide global adaptive system stability and desirable performance. To validate the approach, simulation was performed to a single-link mechanical system with a dynamic friction model and unknown dead zone exists at the system actuation. Then a comparison is presented with the results when there is no dead zone at the system actuation.
Abstract: Educational games (EG) seem to have lots of potential due to digital games popularity and preferences of our younger generations of learners. However, most studies focus on game design and its effectiveness while little has been known about the factors that can affect users to accept or to reject EG for their learning. User acceptance research try to understand the determinants of information systems (IS) adoption among users by investigating both systems factors and users factors. Upon the lack of knowledge on acceptance factors for educational games, we seek to understand the issue. This study proposed a model of acceptance factors based on Unified Theory of Acceptance and Use of Technology (UTAUT). We use original model (performance expectancy, effort expectancy and social influence) together with two new determinants (learning opportunities and enjoyment). We will also investigate the effect of gender and gaming experience that moderate the proposed factors.
Abstract: This paper presents a tested research concept that
implements a complex evolutionary algorithm, genetic algorithm
(GA), in a multi-microcontroller environment. Parallel Distributed
Genetic Algorithm (PDGA) is employed in adaptive beam forming
technique to reduce power usage of adaptive antenna at WCDMA
base station. Adaptive antenna has dynamic beam that requires more
advanced beam forming algorithm such as genetic algorithm which
requires heavy computation and memory space. Microcontrollers are
low resource platforms that are normally not associated with GAs,
which are typically resource intensive. The aim of this project was to
design a cooperative multiprocessor system by expanding the role of
small scale PIC microcontrollers to optimize WCDMA base station
transmitter power. Implementation results have shown that PDGA
multi-microcontroller system returned optimal transmitted power
compared to conventional GA.
Abstract: This paper deals with behavior and capacity of
punching shear force for flat slabs produced from steel fiber
reinforced self compacting concrete (SFRSCC) by application
nonlinear finite element method. Nonlinear finite element analysis on
nine slab specimens was achieved by using ANSYS software. A
general description of the finite element method, theoretical modeling
of concrete and reinforcement are presented. The nonlinear finite
element analysis program ANSYS is utilized owing to its capabilities
to predict either the response of reinforced concrete slabs in the post
elastic range or the ultimate strength of a flat slabs produced from
steel fiber reinforced self compacting concrete (SFRSCC). In order to
verify the analytical model used in this research using test results of
the experimental data, the finite element analysis were performed
then a parametric study of the effect ratio of flexural reinforcement,
ratio of the upper reinforcement, and volume fraction of steel fibers
were investigated. A comparison between the experimental results
and those predicted by the existing models are presented. Results and
conclusions may be useful for designers, have been raised, and
represented.
Abstract: This paper reports on the results of experimental investigations on the performance of a jet pump operated under selected primary flows to optimize the related parameters. For this purpose a two-phase flow jet pump was used employing various profiles of nozzles as the primary device which was designed, fabricated and used along with the combination of mixing tube and diffuser. The profiles employed were circular, conical, and elliptical. The diameter of the nozzle used was 4 mm. The area ratio of the jet pump was 0.16. The test facility created for this purpose was an open loop continuous circulation system. Performance of the jet pump was obtained as iso-efficiency curves on characteristic curves drawn for various water flow rates. To perform the suction capability, evacuation test was conducted at best efficiency point for all the profiles.
Abstract: Graph decompositions are vital in the study of
combinatorial design theory. A decomposition of a graph G is a
partition of its edge set. An n-sun graph is a cycle Cn with an edge
terminating in a vertex of degree one attached to each vertex. In this
paper, we define n-sun decomposition of some even order graphs
with a perfect matching. We have proved that the complete graph
K2n, complete bipartite graph K2n, 2n and the Harary graph H4, 2n have
n-sun decompositions. A labeling scheme is used to construct the n-suns.
Abstract: This paper is a simple and systematic approaches to the design and analysis a pulse width modulation (PWM) based sliding mode controller for buck DC-DC Converters. Various aspects of the design, including the practical problems and the proposed solutions, are detailed. However, these control strategies can't compensate for large load current and input voltage variations. In this paper, a new control strategy by compromising both schemes advantages and avoiding their drawbacks is proposed, analyzed and simulated.
Abstract: The paper compares different channel models used for
modeling Broadband Power-Line Communication (BPLC) system.
The models compared are Zimmermann and Dostert, Philipps,
Anatory et al and Anatory et al generalized Transmission Line (TL)
model. The validity of each model was compared in time domain
with ATP-EMTP software which uses transmission line approach. It
is found that for a power-line network with minimum number of
branches all the models give similar signal/pulse time responses
compared with ATP-EMTP software; however, Zimmermann and
Dostert model indicates the same amplitude but different time delay.
It is observed that when the numbers of branches are increased only
generalized TL theory approach results are comparable with ATPEMTP
results. Also the Multi-Carrier Spread Spectrum (MC-SS)
system was applied to check the implication of such behavior on the
modulation schemes. It is observed that using Philipps on the
underground cable can predict the performance up to 25dB better
than other channel models which can misread the actual performance
of the system. Also modified Zimmermann and Dostert under
multipath can predict a better performance of about 5dB better than
the actual predicted by Generalized TL theory. It is therefore
suggested for a realistic BPLC system design and analyses the model
based on generalized TL theory be used.
Abstract: The paper reflects current state of popularization of
static elasticity modulus of concrete. This parameter is undoubtedly
very important for designing of concrete structures, and very often
neglected and rarely determined before designing concrete
technology itself. The paper describes assessment and comparison of
four mix designs with almost constant dosage of individual
components. The only difference is area of origin of small size
fraction of aggregate 0/4. Development of compressive strength and
static elasticity modulus at the age of 7, 28 and 180 days were
observed. As the experiment showed, designing of individual
components and their quality are the basic factor influencing
elasticity modulus of current concrete.
Abstract: Even it has been recognized that Shape Memory
Alloys (SMA) have a significant potential for deployment actuators,
the number of applications of SMA-based actuators to the present
day is still quite small, due to the need of deep understanding of the
thermo-mechanical behavior of SMA, causing an important need for
a mathematical model able to describe all thermo-mechanical
properties of SMA by relatively simple final set of constitutive
equations. SMAs offer attractive potentials such as: reversible strains
of several percent, generation of high recovery stresses and high
power / weight ratios. The paper tries to provide an overview of the
shape memory functions and a presentation of the designed and
developed temperature control system used for a gripper actuated by
two pairs of differential SMA active springs. An experimental setup
was established, using electrical energy for actuator-s springs heating
process. As for holding the temperature of the SMA springs at certain
level for a long time was developed a control system in order to
avoid the active elements overheating.