Abstract: In this paper static and dynamic response of a
varactor of a micro-phase shifter to DC, step DC and AC
voltages have been studied. By presenting a mathematical
modeling Galerkin-based step by step linearization method
(SSLM) and Galerkin-based reduced order model have been
used to solve the governing static and dynamic equations,
respectively. The calculated static and dynamic pull-in
voltages have been validated by previous experimental and
theoretical results and a good agreement has been achieved.
Then the frequency response and phase diagram of the system
has been studied. It has been shown that applying the DC
voltage shifts down the phase diagram and frequency
response. Also increasing the damping ratio shifts up the
phase diagram.
Abstract: Polymer-like organic thin films were deposited on both
aluminum alloy type 6061 and glass substrates at room temperature by
Plasma Enhanced Chemical Vapor Deposition (PECVD) methodusing
benzene and hexamethyldisiloxane (HMDSO) as precursor materials.
The surface and physical properties of plasma-polymerized organic
thin films were investigated at different r.f. powers. The effects of
benzene/argon ratio on the properties of plasma polymerized benzene
films were also investigated. It is found that using benzene alone
results in a non-coherent and non-adherent powdery deposited
material. The chemical structure and surface properties of the asgrown
plasma polymerized thin films were analyzed on glass
substrates with FTIR and contact angle measurements. FTIR spectra
of benzene deposited film indicated that the benzene rings are
preserved when increasing benzene ratio and/or decreasing r.f.
powers. FTIR spectra of HMDSO deposited films indicated an
increase of the hydrogen concentration and a decrease of the oxygen
concentration with the increase of r.f. power. The contact angle (θ) of
the films prepared from benzene was found to increase by about 43%
as benzene ratio increases from 10% to 20%. θ was then found to
decrease to the original value (51°) when the benzene ratio increases
to 100%. The contact angle, θ, for both benzene and HMDSO
deposited films were found to increase with r.f. power. This signifies
that the plasma polymerized organic films have substantially low
surface energy as the r.f power increases. The corrosion resistance of
aluminum alloy substrate both bare and covered with plasma
polymerized thin films was carried out by potentiodynamic
polarization measurements in standard 3.5 wt. % NaCl solution at
room temperature. The results indicate that the benzene and HMDSO
deposited films are suitable for protection of the aluminum substrate
against corrosion. The changes in the processing parameters seem to
have a strong influence on the film protective ability. Surface
roughness of films deposited on aluminum alloy substrate was
investigated using scanning electron microscopy (SEM). The SEM
images indicate that the surface roughness of benzene deposited films
increase with decreasing the benzene ratio. SEM images of benzene
and HMDSO deposited films indicate that the surface roughness
decreases with increasing r.f. power. Studying the above parameters
indicate that the films produced are suitable for specific practical
applications.
Abstract: Due to its geographical location, Iran is considered one of the earthquake-prone areas where the best way to decrease earthquake effects is supposed to be strengthening the buildings. Even though, one idea suggests that the use of adobe in constructing buildings be prohibited for its weak function especially in earthquake-prone areas, however, regarding ecological considerations, sustainability and other local skills, another idea pays special attention to adobe as one of the construction technologies which is popular among people. From the architectural and technological point of view, as strong sustainable building construction materials, compressed adobe construction materials make most of the construction in urban or rural areas ranging from small to big industrial buildings used to replace common earth blocks in traditional systems and strengthen traditional adobe buildings especially against earthquake. Mentioning efficient construction using compressed adobe system as a reliable replacement for traditional soil construction materials , this article focuses on the experiences of India in the fields of sustainable development of compressed adobe systems in the form of system in which the compressed soil is combined with cement, load bearing building with brick/solid concrete block system, brick system using rat trap bond, metal system with adobe infill and finally emphasizes on the use of these systems in the earthquake-struck city of Bam in Iran.
Abstract: This paper proposes a bi-objective model for the
facility location problem under a congestion system. The idea of the
model is motivated by applications of locating servers in bank
automated teller machines (ATMS), communication networks, and so
on. This model can be specifically considered for situations in which
fixed service facilities are congested by stochastic demand within
queueing framework. We formulate this model with two perspectives
simultaneously: (i) customers and (ii) service provider. The
objectives of the model are to minimize (i) the total expected
travelling and waiting time and (ii) the average facility idle-time.
This model represents a mixed-integer nonlinear programming
problem which belongs to the class of NP-hard problems. In addition,
to solve the model, two metaheuristic algorithms including nondominated
sorting genetic algorithms (NSGA-II) and non-dominated
ranking genetic algorithms (NRGA) are proposed. Besides, to
evaluate the performance of the two algorithms some numerical
examples are produced and analyzed with some metrics to determine
which algorithm works better.
Abstract: MiRNAs participate in gene regulation of translation.
Some studies have investigated the interactions between genes and
intragenic miRNAs. It is important to study the miRNA binding sites
of genes involved in carcinogenesis. RNAHybrid 2.1 and ERNAhybrid
programmes were used to compute the hybridization free
energy of miRNA binding sites. Of these 54 mRNAs, 22.6%, 37.7%,
and 39.7% of miRNA binding sites were present in the 5'UTRs,
CDSs, and 3'UTRs, respectively. The density of the binding sites for
miRNAs in the 5'UTR ranged from 1.6 to 43.2 times and from 1.8 to
8.0 times greater than in the CDS and 3'UTR, respectively. Three
types of miRNA interactions with mRNAs have been revealed: 5'-
dominant canonical, 3'-compensatory, and complementary binding
sites. MiRNAs regulate gene expression, and information on the
interactions between miRNAs and mRNAs could be useful in
molecular medicine. We recommend that newly described sites
undergo validation by experimental investigation.
Abstract: The aim of this paper is to introduce a parametric
distribution model in fatigue life reliability analysis dealing with
variation in material properties. Service loads in terms of responsetime
history signal of Belgian pave were replicated on a multi-axial
spindle coupled road simulator and stress-life method was used to
estimate the fatigue life of automotive stub axle. A PSN curve was
obtained by monotonic tension test and two-parameter Weibull
distribution function was used to acquire the mean life of the
component. A Pearson system was developed to evaluate the fatigue
life reliability by considering stress range intercept and slope of the
PSN curve as random variables. Considering normal distribution of
fatigue strength, it is found that the fatigue life of the stub axle to
have the highest reliability between 10000 – 15000 cycles. Taking
into account the variation of material properties associated with the
size effect, machining and manufacturing conditions, the method
described in this study can be effectively applied in determination of
probability of failure of mass-produced parts.
Abstract: In industry, on of the most important subjects is die
and it's characteristics in which for cutting and forming different
mechanical pieces, various punch and matrix metal die are used.
whereas the common parts which form the main frame die are not
often proportion with pieces and dies therefore using a part as socalled
common part for frames in specified dimension ranges can
decrease the time of designing, occupied space of warehouse and
manufacturing costs. Parts in dies with getting uniform in their shape
and dimension make common parts of dies. Common parts of punch
and matrix metal die are as bolster, guide bush, guide pillar and
shank. In this paper the common parts and effective parameters in
selecting each of them as the primary information are studied,
afterward for selection and design of mechanical parts an
introduction and investigation based on the Mech. Desk. software is
done hence with developing this software can standardize the metal
common parts of punch and matrix. These studies will be so useful
for designer in their designing and also using it has with very much
advantage for manufactures of products in decreasing occupied
spaces by dies.
Abstract: Kazakhstan attaches the great importance to
cooperation with European countries within the framework of
multilateral security organizations such as NATO. Cooperation of
Kazakhstan with the NATO is a prominent aspect of strengthening of
regional security of republic. It covers a wide spectrum of areas, such
as reform of sector of defense and security, military operative
compatibility of armed forces of NATO member-countries and
Kazakhstan, civil emergency planning and scientific cooperation. The
cooperation between Kazakhstan and NATO is based on the mutual
interests of neighboring republics in the region so that the existing
forms of cooperation between Kazakhstan and NATO will not be
negatively perceived both in Asia as well as among CIS countries.
Kazakhstan tailors its participation in the PfP programme through an
annual Individual Partnership Programme, selecting those activities
that will help achieve the goals it has set in the IPAP. Level of
cooperation within the limits of PfP essentially differs on each
republic. Cooperation with Kazakhstan progressed most of all since
has been signed IPAP from the NATO
Abstract: High level and high velocity flood flows are
potentially harmful to bridge piers as evidenced in many toppled
piers, and among them the single-column piers were considered as
the most vulnerable. The flood flow characteristic parameters
including drag coefficient, scouring and vortex shedding are built into
a pier-flood interaction model to investigate structural safety against
flood hazards considering the effects of local scouring, hydrodynamic
forces, and vortex induced resonance vibrations. By extracting the
pier-flood simulation results embedded in a neural networks code,
two cases of pier toppling occurred in typhoon days were reexamined:
(1) a bridge overcome by flash flood near a mountain side;
(2) a bridge washed off in flood across a wide channel near the
estuary. The modeling procedures and simulations are capable of
identifying the probable causes for the tumbled bridge piers during
heavy floods, which include the excessive pier bending moments and
resonance in structural vibrations.
Abstract: A theoretical approach to radiation damage evolution
is developed. Stable temporal behavior taking place in solids under
irradiation are examined as phenomena of self-organization in nonequilibrium
systems.
Experimental effects of temporal self-organization in solids under
irradiation are reviewed. Their essential common properties and
features are highlighted and analyzed.
Dynamical model to describe development of self-oscillation of
density of point defects under stationary irradiation is proposed. The
emphasis is the nonlinear couplings between rate of annealing and
density of defects that determine the kind and parameters of an
arising self-oscillation.
The field of parameters (defect generation rate and environment
temperature) at which self-oscillations develop is found. Bifurcation
curve and self-oscillation period near it is obtained.
Abstract: The paper presents the results of theoretical and
numerical modeling of propagation of shock waves in bubbly liquids
related to nonlinear effects (realistic equation of state, chemical
reactions, two-dimensional effects). On the basis on the Rankine-
Hugoniot equations the problem of determination of parameters of
passing and reflected shock waves in gas-liquid medium for
isothermal, adiabatic and shock compression of the gas component is
solved by using the wide-range equation of state of water in the
analitic form. The phenomenon of shock wave intensification is
investigated in the channel of variable cross section for the
propagation of a shock wave in the liquid filled with bubbles
containing chemically active gases. The results of modeling of the
wave impulse impact on the solid wall covered with bubble layer are
presented.
Abstract: In order to meet environmental norms, Indian fuel
policy aims at producing ultra low sulphur diesel (ULSD) in near
future. A catalyst for meeting such requirements has been developed
and kinetics of this catalytic process is being looked into. In the
present investigations, effect of mass transfer on kinetics of ultra deep
hydrodesulphurization (UDHDS) to produce ULSD has been studied
to determine intrinsic kinetics over a pre-sulphided catalyst.
Experiments have been carried out in a continuous flow micro reactor
operated in the temperature range of 330 to 3600C, whsv of 1 hr-1 at a
pressure of 35 bar, and its parameters estimated. Based on the derived
rate expression and estimated parameters optimum operation range
has been determined for this UDHDS catalyst to obtain ULSD
product.
Abstract: This study endeavors to evaluate the effects of farmers’ training program on the adoption of improved farming practices, the output of rice farming, and the income as well as the profit from rice farming by employing an ex-post non-experimental data in Sierra Leone. It was established that participating in farmers’ training program increased the possibility of adoption of the improved farming activities that were implemented in the study area. Through the training program also, the proceeds from rice production was also established to have increased considerably. These results were in line with the assumption that one of the main constraints on the growth in agricultural output particularly rice cultivation in most African states is the lack of efficient extension programs.
Abstract: In this paper we are to find the optimum multiwavelet for compression of electrocardiogram (ECG) signals and then, selecting it for using with SPIHT codec. At present, it is not well known which multiwavelet is the best choice for optimum compression of ECG. In this work, we examine different multiwavelets on 24 sets of ECG data with entirely different characteristics, selected from MIT-BIH database. For assessing the functionality of the different multiwavelets in compressing ECG signals, in addition to known factors such as Compression Ratio (CR), Percent Root Difference (PRD), Distortion (D), Root Mean Square Error (RMSE) in compression literature, we also employed the Cross Correlation (CC) criterion for studying the morphological relations between the reconstructed and the original ECG signal and Signal to reconstruction Noise Ratio (SNR). The simulation results show that the Cardinal Balanced Multiwavelet (cardbal2) by the means of identity (Id) prefiltering method to be the best effective transformation. After finding the most efficient multiwavelet, we apply SPIHT coding algorithm on the transformed signal by this multiwavelet.
Abstract: This paper presents a Neural Network (NN) identification of icing parameters in an A340 aircraft and a reconfiguration technique to keep the A/C performance close to the performance prior to icing. Five aircraft parameters are assumed to be considerably affected by icing. The off-line training for identifying the clear and iced dynamics is based on the Levenberg-Marquard Backpropagation algorithm. The icing parameters are located in the system matrix. The physical locations of the icing are assumed at the right and left wings. The reconfiguration is based on the technique known as the control mixer approach or pseudo inverse technique. This technique generates the new control input vector such that the A/C dynamics is not much affected by icing. In the simulations, the longitudinal and lateral dynamics of an Airbus A340 aircraft model are considered, and the stability derivatives affected by icing are identified. The simulation results show the successful NN identification of the icing parameters and the reconfigured flight dynamics having the similar performance before the icing. In other words, the destabilizing icing affect is compensated.
Abstract: In the recent past, there has been an increasing interest
in applying evolutionary methods to Knowledge Discovery in
Databases (KDD) and a number of successful applications of Genetic
Algorithms (GA) and Genetic Programming (GP) to KDD have been
demonstrated. The most predominant representation of the
discovered knowledge is the standard Production Rules (PRs) in the
form If P Then D. The PRs, however, are unable to handle
exceptions and do not exhibit variable precision. The Censored
Production Rules (CPRs), an extension of PRs, were proposed by
Michalski & Winston that exhibit variable precision and supports an
efficient mechanism for handling exceptions. A CPR is an
augmented production rule of the form:
If P Then D Unless C, where C (Censor) is an exception to the rule.
Such rules are employed in situations, in which the conditional
statement 'If P Then D' holds frequently and the assertion C holds
rarely. By using a rule of this type we are free to ignore the exception
conditions, when the resources needed to establish its presence are
tight or there is simply no information available as to whether it
holds or not. Thus, the 'If P Then D' part of the CPR expresses
important information, while the Unless C part acts only as a switch
and changes the polarity of D to ~D.
This paper presents a classification algorithm based on evolutionary
approach that discovers comprehensible rules with exceptions in the
form of CPRs.
The proposed approach has flexible chromosome encoding, where
each chromosome corresponds to a CPR. Appropriate genetic
operators are suggested and a fitness function is proposed that
incorporates the basic constraints on CPRs. Experimental results are
presented to demonstrate the performance of the proposed algorithm.
Abstract: The protection issues in distribution systems with open and closed-loop are studied, and a generalized protection setting scheme based on the traditional over current protection theories is proposed to meet the new requirements. The setting method is expected to be easier realized using computer program, so that the on-line adaptive setting for coordination in distribution system can be implemented. An automatic setting program is created and several cases are taken into practice. The setting results are verified by the coordination curves of the protective devices which are plotted using MATLAB.
Abstract: The perfect operation of common Active Filters is depended on accuracy of identification system distortion. Also, using a suitable method in current injection and reactive power compensation, leads to increased filter performance. Due to this fact, this paper presents a method based on predictive current control theory in shunt active filter applications. The harmonics of the load current is identified by using o–d–q reference frame on load current and eliminating the DC part of d–q components. Then, the rest of these components deliver to predictive current controller as a Threephase reference current by using Park inverse transformation. System is modeled in discreet time domain. The proposed method has been tested using MATLAB model for a nonlinear load (with Total Harmonic Distortion=20%). The simulation results indicate that the proposed filter leads to flowing a sinusoidal current (THD=0.15%) through the source. In addition, the results show that the filter tracks the reference current accurately.
Abstract: Internet is nowadays included to all National Curriculums of the elementary school. A comparative study of their
goals leads to the conclusion that a complete curriculum should aim to student-s acquisition of the abilities to navigate and search for
information and additionally to emphasize on the evaluation of the information provided by the World Wide Web. In a constructivistic knowledge framework the design of a course has to take under
consideration the conceptual representations of students. The following paper presents the conceptual representation of students of eleven years old, attending the Sixth Grade of Greek Elementary School about World Wide Web and their use in the design and
implementation of an innovative course.
Abstract: Earthmoving operations are a major part of many
construction projects. Because of the complexity and fast-changing
environment of such operations, the planning and estimating are
crucial on both planning and operational levels. This paper presents
the framework ofa microscopic discrete-event simulation system for
modeling earthmoving operations and conducting productivity
estimations on an operational level.A prototype has been developed
to demonstrate the applicability of the proposed framework, and this
simulation system is presented via a case study based on an actual
earthmoving project. The case study shows that the proposed
simulation model is capable of evaluating alternative operating
strategies and resource utilization at a very detailed level.