Abstract: A composite material with carbon fiber and polymer
matrix has been used as adherent for manufacturing adhesive joints.
In order to evaluate different fiber orientations on joint performance,
the adherents with the 0°, ±15°, ±30°, ±45° fiber orientations were
used in the single lap joint configuration. The joints with an overlap
length of 25 mm were prepared according to the ASTM 1002
specifications and subjected to tensile loadings. The structural
adhesive used was a two-part epoxy to be cured at 70°C for an hour.
First, mechanical behaviors of the adherents were measured using
three point bending test. In the test, considerations were given to
stress to failure and elastic modulus. The results were compared with
theoretical ones using rule of mixture. Then, the joints were
manufactured in a specially prepared jig, after a proper surface
preparation. Experimental results showed that the fiber orientations
of the adherents affected the joint performance considerably; the
joints with ±45° adherents experienced the worst shear strength, half
of those with 0° adherents, and in general, there was a great
relationship between the fiber orientations and failure mechanisms.
Delamination problems were observed for many joints, which were
thought to be due to peel effects at the ends of the overlap. It was
proved that the surface preparation applied to the adherent surface
was adequate. For further explanation of the results, a numerical
work should be carried out using a possible non-linear analysis.
Abstract: This paper investigates the application of metallic
coatings on high fiber volume fraction carbon/epoxy polymer matrix
composites. For the grip of the metallic layer, a method of modifying
the surface of the composite by introducing a mixture of copper and
steel powder (filler powders) which can reduce the impact of thermal
spray particles. The powder was introduced to the surface at the time
of the forming. Arc spray was used to project the zinc coating layer.
The substrate was grit blasted to avoid poor adherence. The porosity, microstructure, and morphology of layers are
characterized by optical microscopy, SEM and image analysis. The
samples were studied also in terms of hardness and erosion resistance.
This investigation did not reveal any visible evidence damage to the
substrates. The hardness of zinc layer was about 25.94 MPa and the
porosity was around (∼6.70%). The erosion test showed that the zinc
coating improves the resistance to erosion. Based on the results
obtained, we can conclude that thermal spraying allows the production
of protective coating on PMC. Zinc coating has been identified as a
compatible material with the substrate. The filler powders layer
protects the substrate from the impact of hot particles and allows
avoiding the rupture of brittle carbon fibers.
Abstract: The rising demand for format-flexible packaging
machines is caused by current market changes. Increasing the formatflexibility
is a new goal for the packaging machine manufacturers’
product development process. There are no methodical or designorientated
tools for a comprehensive consideration of this target. This
paper defines the term format-flexibility in the context of packaging
machines and shows the state-of-the-art for improving the
changeover of production machines. The requirements for a new
approach and the concept itself will be introduced, and the method
elements will be explained. Finally, the use of the concept and the
result of the development of a format-flexible packaging machine
will be shown.
Abstract: Smart metering and demand response are gaining
ground in industrial and residential applications. Smart Appliances
have been given concern towards achieving Smart home. The success
of Smart grid development relies on the successful implementation of
Information and Communication Technology (ICT) in power sector.
Smart Appliances have been the technology under development and
many new contributions to its realization have been reported in the
last few years. The role of ICT here is to capture data in real time,
thereby allowing bi-directional flow of information/data between
producing and utilization point; that lead a way for the attainment of
Smart appliances where home appliances can communicate between
themselves and provide a self-control (switch on and off) using the
signal (information) obtained from the grid. This paper depicts the
background on ICT for smart appliances paying a particular attention
to the current technology and identifying the future ICT trends for
load monitoring through which smart appliances can be achieved to
facilitate an efficient smart home system which promote demand
response program. This paper grouped and reviewed the recent
contributions, in order to establish the current state of the art and
trends of the technology, so that the reader can be provided with a
comprehensive and insightful review of where ICT for smart
appliances stands and is heading to. The paper also presents a brief
overview of communication types, and then narrowed the discussion
to the load monitoring (Non-intrusive Appliances Load Monitoring
‘NALM’). Finally, some future trends and challenges in the further
development of the ICT framework are discussed to motivate future
contributions that address open problems and explore new
possibilities.
Abstract: The maintenance of work rolls in hot strip processing
has been lengthy and difficult tasks for hot strip manufacturer
because heavy work rolls have to be taken out of the production line,
which could take hours. One way to increase the time between
maintenance is to improve the effectiveness of the work roll cooling
system such that the wear and tear more slowly occurs, while the
operation cost is kept low. Therefore, this study aims to improve the
work roll cooling system by providing the manufacturer the
relationship between the work-roll temperature reduced by cooling
and the water flow that can help manufacturer determining the more
effective water flow of the cooling system. The relationship is found
using simulation with a systematic process adjustment so that the
satisfying quality of product is achieved. Results suggest that the
manufacturer could reduce the water flow by 9% with roughly the
same performance. With the same process adjustment, the feasibility
of finishing-mill-stand reduction is also investigated. Results suggest
its possibility.
Abstract: The present paper examines the impact noise
transmission through some floor building assemblies. The Acoubat
software numerical simulation has been used to simulate the impact
noise transmission through different floor configurations used in
Algerian construction mode. The results are compared with the
available measurements. We have developed two experimental
methods, i) field method, and ii) laboratory method using Brüel and
Kjær equipments. The results show that the different cases of floor
configurations need some improvement to ensure the acoustic
comfort in the receiving apartment. The recommended value of the
impact sound level in the receiving room should not exceed 58 dB.
The important results obtained in this paper can be used as platform
to improve the Algerian building acoustic regulation aimed at the
construction of the multi-storey residential building.
Abstract: This paper presents the design and analysis of Liquid Crystal (LC) based tunable reflectarray antenna with slot embedded patch element configurations within X-band frequency range. The slots are shown to modify the surface current distribution on the patch element of reflectarray which causes the resonant patch element to provide different resonant frequencies depending on the slot dimensions. The simulated results are supported and verified by waveguide scattering parameter measurements of different reflectarray unit cells. Different rectangular slots on patch element have been fabricated and a change in resonant frequency from 10.46GHz to 8.78GHz has been demonstrated as the width of the rectangular slot is varied from 0.2W to 0.6W. The rectangular slot in the center of the patch element has also been utilized for the frequency tunable reflectarray antenna design based on K-15 Nematic LC. For the active reflectarray antenna design, a frequency tunability of 1.2% from 10GHz to 9.88GHz has been demonstrated with a dynamic phase range of 103° provided by the measured scattering parameter results. Time consumed by liquid crystals for reconfiguration, which is one of the drawback of LC based design, has also been disused in this paper.
Abstract: Wireless sensors, also known as wireless sensor nodes,
have been making a significant impact on human daily life. The
Radio Frequency Identification (RFID) and Wireless Sensor Network
(WSN) are two complementary technologies; hence, an integrated
implementation of these technologies expands the overall
functionality in obtaining long-range and real-time information on the
location and properties of objects and people. An approach for
integrating ZigBee and RFID networks is proposed in this paper, to
create an energy-efficient network improved by the benefits of
combining ZigBee and RFID architecture. Furthermore, the
compatibility and requirements of the ZigBee device and
communication links in the typical RFID system which is presented
with the real world experiment on the capabilities of the proposed
RFID system.
Abstract: Growth and remodeling of biological structures have
gained lots of attention over the past decades. Determining the
response of living tissues to mechanical loads is necessary for a wide
range of developing fields such as prosthetics design or computerassisted
surgical interventions. It is a well-known fact that biological
structures are never stress-free, even when externally unloaded. The
exact origin of these residual stresses is not clear, but theoretically,
growth is one of the main sources. Extracting body organ’s shapes
from medical imaging does not produce any information regarding
the existing residual stresses in that organ. The simplest cause of such
stresses is gravity since an organ grows under its influence from
birth. Ignoring such residual stresses might cause erroneous results in
numerical simulations. Accounting for residual stresses due to tissue
growth can improve the accuracy of mechanical analysis results. This
paper presents an original computational framework based on gradual
growth to determine the residual stresses due to growth. To illustrate
the method, we apply it to a finite element model of a healthy human
face reconstructed from medical images. The distribution of residual
stress in facial tissues is computed, which can overcome the effect of
gravity and maintain tissues firmness. Our assumption is that tissue
wrinkles caused by aging could be a consequence of decreasing
residual stress and thus not counteracting gravity. Taking into
account these stresses seems therefore extremely important in
maxillofacial surgery. It would indeed help surgeons to estimate
tissues changes after surgery.
Abstract: Intellectual capital is one of the most valuable and
important parts of the intangible assets of enterprises especially in
knowledge-based enterprises. With respect to increasing gap between
the market value and the book value of the companies, intellectual
capital is one of the components that can be placed in this gap. This
paper uses the value added efficiency of the three components,
capital employed, human capital and structural capital, to measure the
intellectual capital efficiency of Iranian industries groups, listed in
the Tehran Stock Exchange (TSE), using a 8 years period data set
from 2005 to 2012. In order to analyze the effect of intellectual
capital on the market-to-book value ratio of the companies, the data
set was divided into 10 industries, Banking, Pharmaceutical, Metals
& Mineral Nonmetallic, Food, Computer, Building, Investments,
Chemical, Cement and Automotive, and the panel data method was
applied to estimating pooled OLS. The results exhibited that value
added of capital employed has a positive significant relation with
increasing market value in the industries, Banking, Metals & Mineral
Nonmetallic, Food, Computer, Chemical and Cement, and also,
showed that value added efficiency of structural capital has a positive
significant relation with increasing market value in the Banking,
Pharmaceutical and Computer industries groups. The results of the
value added showed a negative relation with the Banking and
Pharmaceutical industries groups and a positive relation with
computer and Automotive industries groups. Among the studied
industries, computer industry has placed the widest gap between the
market value and book value in its intellectual capital.
Abstract: In this paper, a method has been developed to
construct the membership surfaces of row and column vectors and
arithmetic operations of imprecise matrix. A matrix with imprecise
elements would be called an imprecise matrix. The membership
surface of imprecise vector has been already shown based on
Randomness-Impreciseness Consistency Principle. The Randomness-
Impreciseness Consistency Principle leads to defining a normal law
of impreciseness using two different laws of randomness. In this
paper, the author has shown row and column membership surfaces
and arithmetic operations of imprecise matrix and demonstrated with
the help of numerical example.
Abstract: The Hall Coefficient (HC) and the Magnetoresistance (MR) have been studied in two-dimensional systems. The HC and the MR in Rectangular Quantum Wire (RQW) subjected to a crossed DC electric field and magnetic field in the presence of a Strong Electromagnetic Wave (EMW) characterized by electric field are studied in this work. Using the quantum kinetic equation for electrons interacting with optical phonons, we obtain the analytic expressions for the HC and the MR with a dependence on magnetic field, EMW frequency, temperatures of systems and the length characteristic parameters of RQW. These expressions are different from those obtained for bulk semiconductors and cylindrical quantum wires. The analytical results are applied to GaAs/GaAs/Al. For this material, MR depends on the ratio of the EMW frequency to the cyclotron frequency. Indeed, MR reaches a minimum at the ratio 5/4, and when this ratio increases, it tends towards a saturation value. The HC can take negative or positive values. Each curve has one maximum and one minimum. When magnetic field increases, the HC is negative, achieves a minimum value and then increases suddenly to a maximum with a positive value. This phenomenon differs from the one observed in cylindrical quantum wire, which does not have maximum and minimum values.
Abstract: Mumbai, being traditionally the epicenter of India's
trade and commerce, the existing major ports such as Mumbai and
Jawaharlal Nehru Ports (JN) situated in Thane estuary are also
developing its waterfront facilities. Various developments over the
passage of decades in this region have changed the tidal flux
entering/leaving the estuary. The intake at Pir-Pau is facing the
problem of shortage of water in view of advancement of shoreline,
while jetty near Ulwe faces the problem of ship scheduling due to
existence of shallower depths between JN Port and Ulwe Bunder. In
order to solve these problems, it is inevitable to have information
about tide levels over a long duration by field measurements.
However, field measurement is a tedious and costly affair;
application of artificial intelligence was used to predict water levels
by training the network for the measured tide data for one lunar tidal
cycle. The application of two layered feed forward Artificial Neural
Network (ANN) with back-propagation training algorithms such as
Gradient Descent (GD) and Levenberg-Marquardt (LM) was used to
predict the yearly tide levels at waterfront structures namely at Ulwe
Bunder and Pir-Pau. The tide data collected at Apollo Bunder, Ulwe,
and Vashi for a period of lunar tidal cycle (2013) was used to train,
validate and test the neural networks. These trained networks having
high co-relation coefficients (R= 0.998) were used to predict the tide
at Ulwe, and Vashi for its verification with the measured tide for the
year 2000 & 2013. The results indicate that the predicted tide levels
by ANN give reasonably accurate estimation of tide. Hence, the
trained network is used to predict the yearly tide data (2015) for
Ulwe. Subsequently, the yearly tide data (2015) at Pir-Pau was
predicted by using the neural network which was trained with the
help of measured tide data (2000) of Apollo and Pir-Pau. The analysis of measured data and study reveals that: The
measured tidal data at Pir-Pau, Vashi and Ulwe indicate that there is
maximum amplification of tide by about 10-20 cm with a phase lag
of 10-20 minutes with reference to the tide at Apollo Bunder
(Mumbai). LM training algorithm is faster than GD and with increase
in number of neurons in hidden layer and the performance of the
network increases. The predicted tide levels by ANN at Pir-Pau and
Ulwe provides valuable information about the occurrence of high and
low water levels to plan the operation of pumping at Pir-Pau and
improve ship schedule at Ulwe.
Abstract: Discussing the nexus between global health policy and local practices, this article addresses the recent Ebola outbreak as a role model for narrative co-constructions of epidemic risk. We will demonstrate in how far a theory-driven and methodologically rooted analysis of narrativity can help to improve mechanisms of prevention and intervention whenever epidemic risk needs to be addressed locally in order to contribute to global health. Analyzing the narrative transformation of Ebola, we will also address issues of transcultural problem-solving and of normative questions at stake. In this regard, we seek to contribute to a better understanding of a key question of global health and justice as well as to the underlying ethical questions. By highlighting and analyzing the functions of narratives, this paper provides a translational approach to refine our practices by which we address epidemic risk, be it on the national, the transnational or the global scale.
Abstract: Landfill leachates contain a number of persistent pollutants, including heavy metals. They have the ability to spread in ecosystems and accumulate in fish which most of them are classified as top-consumers of trophic chains. Fish are freely swimming organisms; but perhaps, due to their species-specific ecological and behavioral properties, they often prefer the most suitable biotopes and therefore, did not avoid harmful substances or environments. That is why it is necessary to evaluate the persistent pollutant dispersion in hydroecosystem using fish tissue metal concentration. In hydroecosystems of hybrid type (e.g. river-pond-river) the distance from the pollution source could be a perfect indicator of such a kind of metal distribution. The studies were carried out in the Kairiai landfill neighboring hybrid-type ecosystem which is located 5 km east of the Šiauliai City. Fish tissue (gills, liver, and muscle) metal concentration measurements were performed on two types of ecologically-different fishes according to their feeding characteristics: benthophagous (Gibel carp, roach) and predatory (Northern pike, perch). A number of mathematical models (linear, non-linear, using log and other transformations) have been applied in order to identify the most satisfactorily description of the interdependence between fish tissue metal concentration and the distance from the pollution source. However, the only one log-multiple regression model revealed the pattern that the distance from the pollution source is closely and positively correlated with metal concentration in all predatory fish tissues studied (gills, liver, and muscle).
Abstract: Magnetic Resonance Imaging Contrast Agents
(MRI-CM) are significant in the clinical and biological imaging as
they have the ability to alter the normal tissue contrast, thereby
affecting the signal intensity to enhance the visibility and detectability
of images. Superparamagnetic Iron Oxide (SPIO) nanoparticles,
coated with dextran or carboxydextran are currently available for
clinical MR imaging of the liver. Most SPIO contrast agents are
T2 shortening agents and Resovist (Ferucarbotran) is one of a
clinically tested, organ-specific, SPIO agent which has a low
molecular carboxydextran coating. The enhancement effect of
Resovist depends on its relaxivity which in turn depends on factors
like magnetic field strength, concentrations, nanoparticle properties,
pH and temperature. Therefore, this study was conducted to
investigate the impact of field strength and different contrast
concentrations on enhancement effects of Resovist. The study
explored the MRI signal intensity of Resovist in the physiological
range of plasma from T2-weighted spin echo sequence at three
magnetic field strengths: 0.47 T (r1=15, r2=101), 1.5 T (r1=7.4,
r2=95), and 3 T (r1=3.3, r2=160) and the range of contrast
concentrations by a mathematical simulation. Relaxivities of r1 and r2
(L mmol-1 Sec-1) were obtained from a previous study and the selected
concentrations were 0.05, 0.06, 0.07, 0.08, 0.09, 0.1, 0.2, 0.3, 0.4, 0.5,
0.6, 0.7, 0.8, 0.9, 1.0, 2.0, and 3.0 mmol/L. T2-weighted images were
simulated using TR/TE ratio as 2000 ms /100 ms. According to the
reference literature, with increasing magnetic field strengths, the
r1 relaxivity tends to decrease while the r2 did not show any
systematic relationship with the selected field strengths. In parallel,
this study results revealed that the signal intensity of Resovist at lower
concentrations tends to increase than the higher concentrations. The
highest reported signal intensity was observed in the low field strength
of 0.47 T. The maximum signal intensities for 0.47 T, 1.5 T and 3 T
were found at the concentration levels of 0.05, 0.06 and 0.05 mmol/L,
respectively. Furthermore, it was revealed that, the concentrations
higher than the above, the signal intensity was decreased
exponentially. An inverse relationship can be found between the field
strength and T2 relaxation time, whereas, the field strength was
increased, T2 relaxation time was decreased accordingly. However,
resulted T2 relaxation time was not significantly different between
0.47 T and 1.5 T in this study. Moreover, a linear correlation of
transverse relaxation rates (1/T2, s–1) with the concentrations of
Resovist can be observed. According to these results, it can conclude
that the concentration of SPIO nanoparticle contrast agents and the
field strengths of MRI are two important parameters which can affect the signal intensity of T2-weighted SE sequence. Therefore, when MR
imaging those two parameters should be considered prudently.
Abstract: The increasing availability of information about earth
surface elevation (Digital Elevation Models DEM) generated from
different sources (remote sensing, Aerial Images, Lidar) poses the
question about how to integrate and make available to the most than
possible audience this huge amount of data. In order to exploit the potential of 3D elevation representation the
quality of data management plays a fundamental role. Due to the high
acquisition costs and the huge amount of generated data, highresolution
terrain surveys tend to be small or medium sized and
available on limited portion of earth. Here comes the need to merge
large-scale height maps that typically are made available for free at
worldwide level, with very specific high resolute datasets. One the
other hand, the third dimension increases the user experience and the
data representation quality, unlocking new possibilities in data
analysis for civil protection, real estate, urban planning, environment
monitoring, etc. The open-source 3D virtual globes, which are
trending topics in Geovisual Analytics, aim at improving the
visualization of geographical data provided by standard web services
or with proprietary formats. Typically, 3D Virtual globes like do not
offer an open-source tool that allows the generation of a terrain
elevation data structure starting from heterogeneous-resolution terrain
datasets. This paper describes a technological solution aimed to set
up a so-called “Terrain Builder”. This tool is able to merge
heterogeneous-resolution datasets, and to provide a multi-resolution
worldwide terrain services fully compatible with CesiumJS and
therefore accessible via web using traditional browser without any
additional plug-in.
Abstract: The process of human resources management in the structures of corporate groups demonstrates certain specificity, resulting from the division of decision-making and executive competencies, which occurs within these structures between a parent company and its subsidiaries. The subprocess of employee assessment is considered crucial, since it provides information for the implementation of personnel function. The empirical studies conducted in corporate groups, within which at least one company is located in Poland, confirmed the critical significance of employee assessment systems in the process of human resources management in corporate groups. Parent companies, most often, retain their decision-making authority within the framework of the discussed process and introduce uniform employee assessment and personnel controlling systems to subsidiary companies. However, the instruments for employee assessment applied in corporate groups do not present such specificity.
Abstract: With 40% of total world energy consumption,
building systems are developing into technically complex large
energy consumers suitable for application of sophisticated power
management approaches to largely increase the energy efficiency
and even make them active energy market participants. Centralized
control system of building heating and cooling managed by
economically-optimal model predictive control shows promising
results with estimated 30% of energy efficiency increase. The research
is focused on implementation of such a method on a case study
performed on two floors of our faculty building with corresponding
sensors wireless data acquisition, remote heating/cooling units and
central climate controller. Building walls are mathematically modeled
with corresponding material types, surface shapes and sizes. Models
are then exploited to predict thermal characteristics and changes in
different building zones. Exterior influences such as environmental
conditions and weather forecast, people behavior and comfort
demands are all taken into account for deriving price-optimal climate
control. Finally, a DC microgrid with photovoltaics, wind turbine,
supercapacitor, batteries and fuel cell stacks is added to make the
building a unit capable of active participation in a price-varying
energy market. Computational burden of applying model predictive
control on such a complex system is relaxed through a hierarchical
decomposition of the microgrid and climate control, where the
former is designed as higher hierarchical level with pre-calculated
price-optimal power flows control, and latter is designed as lower
level control responsible to ensure thermal comfort and exploit
the optimal supply conditions enabled by microgrid energy flows
management. Such an approach is expected to enable the inclusion
of more complex building subsystems into consideration in order to
further increase the energy efficiency.
Abstract: This paper describes a simple way to control the speed
of PMBLDC motor using Fuzzy logic control method. In the
conventional PI controller the performance of the motor system is
simulated and the speed is regulated by using PI controller. These
methods used to improve the performance of PMSM drives, but in
some cases at different operating conditions when the dynamics of
the system also vary over time and it can change the reference speed,
parameter variations and the load disturbance. The simulation is
powered with the MATLAB program to get a reliable and flexible
simulation. In order to highlight the effectiveness of the speed control
method the FLC method is used. The proposed method targeted in
achieving the improved dynamic performance and avoids the
variations of the motor drive. This drive has high accuracy, robust
operation from near zero to high speed. The effectiveness and
flexibility of the individual techniques of the speed control method
will be thoroughly discussed for merits and demerits and finally
verified through simulation and experimental results for comparative
analysis.