Abstract: The mixing of pollutions and sediments in near shore regions of natural water bodies depends heavily on the characteristics such as the strength and frequency of flow instability. In the present paper, the instability of natural convection induced by absorption of solar radiation in littoral regions is considered. Spectral analysis is conducted on the quasi-steady state flow to reveal the power and frequency modes of the instability at various positions. Results indicate that the power of instability, the number of frequency modes, the prominence of higher frequency modes, and the highest frequency mode increase with the offshore distance and/or Rayleigh number. Harmonic modes are present at relatively low Rayleigh numbers. For a given offshore distance, the position with the strongest power of instability is located adjacent to the sloping bottom while the frequency modes are the same over the local depth. As the Rayleigh number increases, the unstable region extends toward the shore.
Abstract: In this paper, the bond strength of thermal spray
coatings in high speed shafts has been studied. The metallurgical and
mechanical studies has been made on the coated samples and shaft
using optical microscopy, scanning electron microscopy (SEM).
Abstract: Laser Metal Deposition (LMD) is an additive manufacturing process with capabilities that include: producing new
part directly from 3 Dimensional Computer Aided Design (3D CAD)
model, building new part on the existing old component and repairing an existing high valued component parts that would have
been discarded in the past. With all these capabilities and its advantages over other additive manufacturing techniques, the
underlying physics of the LMD process is yet to be fully understood probably because of high interaction between the processing
parameters and studying many parameters at the same time makes it
further complex to understand. In this study, the effect of laser power
and powder flow rate on physical properties (deposition height and
deposition width), metallurgical property (microstructure) and
mechanical (microhardness) properties on laser deposited most
widely used aerospace alloy are studied. Also, because the Ti6Al4V
is very expensive, and LMD is capable of reducing buy-to-fly ratio
of aerospace parts, the material utilization efficiency is also studied.
Four sets of experiments were performed and repeated to establish repeatability using laser power of 1.8 kW and 3.0 kW, powder flow
rate of 2.88 g/min and 5.67 g/min, and keeping the gas flow rate and
scanning speed constant at 2 l/min and 0.005 m/s respectively. The
deposition height / width are found to increase with increase in laser
power and increase in powder flow rate. The material utilization is favoured by higher power while higher powder flow rate reduces
material utilization. The results are presented and fully discussed.
Abstract: Text Mining is around applying knowledge discovery techniques to unstructured text is termed knowledge discovery in text (KDT), or Text data mining or Text Mining. In Neural Network that address classification problems, training set, testing set, learning rate are considered as key tasks. That is collection of input/output patterns that are used to train the network and used to assess the network performance, set the rate of adjustments. This paper describes a proposed back propagation neural net classifier that performs cross validation for original Neural Network. In order to reduce the optimization of classification accuracy, training time. The feasibility the benefits of the proposed approach are demonstrated by means of five data sets like contact-lenses, cpu, weather symbolic, Weather, labor-nega-data. It is shown that , compared to exiting neural network, the training time is reduced by more than 10 times faster when the dataset is larger than CPU or the network has many hidden units while accuracy ('percent correct') was the same for all datasets but contact-lences, which is the only one with missing attributes. For contact-lences the accuracy with Proposed Neural Network was in average around 0.3 % less than with the original Neural Network. This algorithm is independent of specify data sets so that many ideas and solutions can be transferred to other classifier paradigms.
Abstract: The problem of mapping tasks onto a computational grid with the aim to minimize the power consumption and the makespan subject to the constraints of deadlines and architectural requirements is considered in this paper. To solve this problem, we propose a solution from cooperative game theory based on the concept of Nash Bargaining Solution. The proposed game theoretical technique is compared against several traditional techniques. The experimental results show that when the deadline constraints are tight, the proposed technique achieves superior performance and reports competitive performance relative to the optimal solution.
Abstract: This paper presents comparative emission study of
newly introduced gasoline/LPG bifuel automotive engine in Indian
market. Emissions were tested as per LPG-Bharat stage III driving
cycle. Emission tests were carried out for urban cycle and extra urban
cycle. Total time for urban and extra urban cycle was 1180 sec.
Engine was run in LPG mode by using conversion system. Emissions
were tested as per standard procedure and were compared. Corrected
emissions were computed by deducting ambient reading from sample
reading. Paper describes detail emission test procedure and results
obtained. CO emissions were in the range of38.9 to 111.3 ppm. HC
emissions were in the range of 18.2 to 62.6 ppm. Nox emissions were
08 to 3.9 ppm and CO2 emissions were from 6719.2 to 8051 ppm.
Paper throws light on emission results of LPG vehicles recently
introduced in Indian automobile market. Objectives of this
experimental study were to measure emissions of engines in gasoline
& LPG mode and compare them.
Abstract: Organizational structure of the Turkish state
universities is a form of bureaucracy, a high efficient system in
rational and formal control. According to the dimensional approach
bureaucracy can occur in an organization in a degree, as some
bureaucracy characteristics can be stronger than others. In addition,
the units of an organization due to their different specific
characteristic properties can perceive the bureaucracy differently. In
the study, Hall-s Organizational Inventory, which was developed for
evaluating the degree of bureaucratization from the dimensional
perspective, is used to find out if there is a difference in the
perception of the bureaucracy between the academicians working in
three different departments and two faculties in the same university.
Abstract: This research is to study the types of products and
services that employs 'ambient media and respective techniques in its
advertisement materials. Data collection has been done via analyses of a total of 62 advertisements that employed ambient media
approach in Thailand during the years 2004 to 2011. The 62 advertisement were qualifying advertisements of the Adman Awards
& Symposium under the category of Outdoor & Ambience. Analysis
results reveal that there is a total of 14 products and services that
chooses to utilize ambient media in its advertisement. Amongst all ambient media techniques, 'intrusion' uses the value of a medium in
its representation of content most often. Following intrusion is 'interaction', where consumers are invited to participate and interact
with the advertising materials. 'Illusion' ranks third in its ability to subject the viewers to distortions of reality that makes the division
between reality and fantasy less clear.
Abstract: We propose a reduced-ordermodel for the instantaneous
hydrodynamic force on a cylinder. The model consists of a system of
two ordinary differential equations (ODEs), which can be integrated
in time to yield very accurate histories of the resultant force and
its direction. In contrast to several existing models, the proposed
model considers the actual (total) hydrodynamic force rather than its
perpendicular or parallel projection (the lift and drag), and captures
the complete force rather than the oscillatory part only. We study
and provide descriptions of the relationship between the model
parameters, evaluated utilizing results from numerical simulations,
and the Reynolds number so that the model can be used at any
arbitrary value within the considered range of 100 to 500 to provide
accurate representation of the force without the need to perform timeconsuming
simulations and solving the partial differential equations
(PDEs) governing the flow field.
Abstract: In this paper a novel method for multiple one dimensional real valued sinusoidal signal frequency estimation in the presence of additive Gaussian noise is postulated. A computationally simple frequency estimation method with efficient statistical performance is attractive in many array signal processing applications. The prime focus of this paper is to combine the subspace-based technique and a simple peak search approach. This paper presents a variant of the Propagator Method (PM), where a collaborative approach of SUMWE and Propagator method is applied in order to estimate the multiple real valued sine wave frequencies. A new data model is proposed, which gives the dimension of the signal subspace is equal to the number of frequencies present in the observation. But, the signal subspace dimension is twice the number of frequencies in the conventional MUSIC method for estimating frequencies of real-valued sinusoidal signal. The statistical analysis of the proposed method is studied, and the explicit expression of asymptotic (large-sample) mean-squared-error (MSE) or variance of the estimation error is derived. The performance of the method is demonstrated, and the theoretical analysis is substantiated through numerical examples. The proposed method can achieve sustainable high estimation accuracy and frequency resolution at a lower SNR, which is verified by simulation by comparing with conventional MUSIC, ESPRIT and Propagator Method.
Abstract: A CFD study on heat flux reduction in hypersonic flow with opposing jet has been conducted. Flowfield parameters, reattachment point position, surface pressure distributions and heat flux distributions are obtained and validated with experiments. The physical mechanism of heat reduction has been analyzed. When the opposing jet blows, the freestream is blocked off, flows to the edges and not interacts with the surface to form aerodynamic heating. At the same time, the jet flows back to form cool recirculation region, which reduces the difference in temperature between the surface and the nearby gas, and then reduces the heat flux. As the pressure ratio increases, the interface between jet and freestream is gradually pushed away from the surface. Larger the total pressure ratio is, lower the heat flux is. To study the effect of the intensity of opposing jet more reasonably, a new parameter RPA has been introduced by combining the flux and the total pressure ratio. The study shows that the same shock wave position and total heat load can be obtained with the same RPA with different fluxes and the total pressures, which means the new parameter could stand for the intensity of opposing jet and could be used to analyze the influence of opposing jet on flow field and aerodynamic heating.
Abstract: The main objective of this research was to investigate
the biosorption capacity for biofilms of sulphate reducing bacteria
(SRB) to remove heavy metals, such as Zn, Pb and Cd from
rainwater using laboratory-scale reactors containing mixed support
media. Evidence showed that biosorption had contributed to removal
of heavy metals including Zn, Pb and Cd in presence of SRB and
SRB were also found in the aqueous samples from reactors.
However, the SRB and specific families (Desulfobacteriaceae and
Desulfovibrionaceae) were found mainly in the biomass samples
taken from all reactors at the end of the experiment. EDX-analysis
of reactor solids at end of experiment showed that heavy metals Zn,
Pb and Cd had also accumulated in these precipitates.
Abstract: Several different cements have been tested to evaluate
their potential to leach calcium, chromium and aluminum ions in soft
water environment. The research allows comparing some different
cements in order to the potential risk of water contamination. This
can be done only in the same environment. To reach the results in
reasonable short time intervals and to make heavy metals
measurements with high accuracy, demineralized water was used. In
this case the conditions of experiments are far away from the water
supply practice, but short time experiments and measurably high
concentrations of elements in the water solution are an important
advantage. Moreover leaching mechanisms can be recognized, our
experiments reported here refer to this kind of cements evaluation.
Abstract: In spite of the advent of new materials, clay bricks
remain, arguably, the most popular construction materials today.
Nevertheless the low cost and versatility of clay bricks cannot always
be associated with high environmental and sustainable values,
especially in terms of raw material sources and manufacturing
processes. At the same time, the worldwide agricultural footprint is
fast growing, with vast agricultural land cultivation and active
expansion of the agro-based industry. The resulting large quantities of
agricultural wastes, unfortunately, are not always well managed or
utilised. These wastes can be recycled, such as by retrieving fibres
from disposed leaves and fruit bunches, and then incorporated in
brick-making. This way the clay bricks are made a 'greener' building
material and the discarded natural wastes can be reutilised, avoiding
otherwise wasteful landfill and harmful open incineration. This study
examined the physical and mechanical properties of clay bricks made
by adding two natural fibres to a clay-water mixture, with baked and
non-baked conditions. The fibres were sourced from pineapple leaves
(PF) and oil palm fruit bunch (OF), and added within the range of
0.25-0.75 %. Cement was added as a binder to the mixture at 5-15 %.
Although the two fibres had different effects on the bricks produced,
cement appeared to dominate the compressive strength. The
non-baked bricks disintegrated when submerged in water, while the
baked ones displayed cement-dependent characteristics in
water-absorption and density changes. Interestingly, further increase
in fibre content did not cause significant density decrease in both the
baked and non-baked bricks.
Abstract: The combustion of liquid fuel in the porous burner
(PB) was experimented to investigate evaporation mechanism and
combustion behavior. The diesel oil was used as fuel and the pebbles
carefully chosen in the same size like the solid sphere homogeneously
was adopted as the porous media. Two structures of the liquid porous
burner, i.e. the PB without and with installation of porous emitter
(PE), were performed. PE was installed by lower than PB with
distance of 20 cm. The pebbles having porosity (φ) of 0.45 and 0.52
were, respectively, used in PB and PE. The fuel was supplied dropwise
from the top through the PB and the combustion was occurred between
PB and PE. Axial profiles of temperature along the burner length were
measured to clarify the evaporation and combustion phenomena. The
pollutant emission characteristics were monitored at the burner exit.
From the experiment, it was found that the temperature profiles of both
structures decreased with the three ways swirling air flows (QA)
increasing. On the other hand, the temperature profiles increased with
fuel heat input (QF). Obviously, the profile of the porous burner
installed with PE was higher than that of the porous burner without
PE
Abstract: Sensor network applications are often data centric and
involve collecting data from a set of sensor nodes to be delivered
to various consumers. Typically, nodes in a sensor network are
resource-constrained, and hence the algorithms operating in these
networks must be efficient. There may be several algorithms available
implementing the same service, and efficient considerations may
require a sensor application to choose the best suited algorithm. In
this paper, we present a systematic evaluation of a set of algorithms
implementing the data gathering service. We propose a modular
infrastructure for implementing such algorithms in TOSSIM with
separate configurable modules for various tasks such as interest
propagation, data propagation, aggregation, and path maintenance.
By appropriately configuring these modules, we propose a number
of data gathering algorithms, each of which incorporates a different
set of heuristics for optimizing performance. We have performed
comprehensive experiments to evaluate the effectiveness of these
heuristics, and we present results from our experimentation efforts.
Abstract: The objectives of this research are to search the
management pattern of Bang Khonthi lodging entrepreneurs for
sufficient economy ways, to know the threat that affects this sector
and design fit arrangement model to sustain their business with
Samut Songkram style. What will happen if they do not use this
approach? Will they have a financial crisis? The data and information
are collected by informal discussions with 8 managers and 400
questionnaires. A mixed methods of both qualitative research and
quantitative research are used. Bent Flyvbjerg-s phronesis is utilized
for this analysis. Our research will prove that sufficient economy can
help small business firms to solve their problems. We think that the
results of our research will be a financial model to solve many
problems of the entrepreneurs and this way will can be a model for
other provinces of Thailand.
Abstract: The development of many measurement and inspection systems of products based on real-time image processing can not be carried out totally in a laboratory due to the size or the temperature of the manufactured products. Those systems must be developed in successive phases. Firstly, the system is installed in the production line with only an operational service to acquire images of the products and other complementary signals. Next, a recording service of the image and signals must be developed and integrated in the system. Only after a large set of images of products is available, the development of the real-time image processing algorithms for measurement or inspection of the products can be accomplished under realistic conditions. Finally, the recording service is turned off or eliminated and the system operates only with the real-time services for the acquisition and processing of the images. This article presents a systematic performance evaluation of the image compression algorithms currently available to implement a real-time recording service. The results allow establishing a trade off between the reduction or compression of the image size and the CPU time required to get that compression level.
Abstract: Five lignin samples were fractionated with
Acetone/Water mixtures and the obtained fractions were subjected to
extensive structural characterization, including Fourier Transform
Infrared (FT-IR), Gel permeation Chromatography (GPC) and
Phosphorus-31 NMR spectroscopy (31P-NMR). The results showed
that for all studied lignins the solubility increases with the increment
of the acetone concentration. Wheat straw lignin has the highest
solubility in 90/10 (v/v) Acetone/Water mixture, 400 mg lignin being
dissolved in 1 mL mixture. The weight average molecular weight of
the obtained fractions increased with the increment of acetone
concentration and thus with solubility. 31P-NMR analysis based on
lignin modification by reactive phospholane into phosphitylated
compounds was used to differentiate and quantify the different types
of OH groups (aromatic, aliphatic, and carboxylic) found in the
fractions obtained with 70/30 (v/v) Acetone/Water mixture.
Abstract: Multiple sequence alignment is a fundamental part in
many bioinformatics applications such as phylogenetic analysis.
Many alignment methods have been proposed. Each method gives a
different result for the same data set, and consequently generates a
different phylogenetic tree. Hence, the chosen alignment method
affects the resulting tree. However in the literature, there is no
evaluation of multiple alignment methods based on the comparison of
their phylogenetic trees. This work evaluates the following eight
aligners: ClustalX, T-Coffee, SAGA, MUSCLE, MAFFT, DIALIGN,
ProbCons and Align-m, based on their phylogenetic trees (test trees)
produced on a given data set. The Neighbor-Joining method is used
to estimate trees. Three criteria, namely, the dNNI, the dRF and the
Id_Tree are established to test the ability of different alignment
methods to produce closer test tree compared to the reference one
(true tree). Results show that the method which produces the most
accurate alignment gives the nearest test tree to the reference tree.
MUSCLE outperforms all aligners with respect to the three criteria
and for all datasets, performing particularly better when sequence
identities are within 10-20%. It is followed by T-Coffee at lower
sequence identity (30%), trees scores of all methods
become similar.