Abstract: Massive rock avalanches formed some of the largest landslide deposits on Earth and they represent one of the major geohazards in high-relief mountains. This paper interprets a very large sedimentary fan (the Sernio fan, Valtellina, Northern Italy), located 20 Km SW from Val Pola Rock avalanche (1987), as the deposit of a partial collapse of a Deep Seated Gravitational Slope Deformation (DSGSD), afterwards eroded and buried by debris flows. The proposed emplacement sequence has been reconstructed based on geomorphological, structural and mechanical evidences. The Sernio fan is actually considered anomalous with reference to the very high ratio between the fan area (≈ 4.5km2) and the basin area (≈ 3km2). The morphology of the fan area is characterised by steep slopes (dip ≈ 20%) and the fan apex is extended for 1.8 km inside the small catchment basin. This sedimentary fan was originated by a landslide that interested a part of a large deep-seated gravitational slope deformation, involving a wide area of about 55 km². The main controlling factor is tectonic and it is related to the proximity to regional fault systems and the consequent occurrence of fault weak rocks (GSI locally lower than 10 with compressive stress lower than 20MPa). Moreover, the fan deposit shows sedimentary evidences of recent debris flow events. The best current explanation of the Sernio fan involves an initial failure of some hundreds of Mm3. The run-out was quite limited because of the morphology of Valtellina’s valley floor, and the deposit filled the main valley forming a landslide dam, as confirmed by the lacustrine deposits detected upstream the fan. Nowadays the debris flow events represent the main hazard in the study area.
Abstract: Presented article outlines a rationale, why it is
necessary to develop competence about infrastructure risk in water
transport. Climate changes are evident and require special attention
and global monitoring. Current risk assessment methods for Inland
waterway transport just consider some dramatic events. We present a
new method for the assessment of risk and vulnerability of inland
waterway transport where river depth represents a crucial part. The
analysis of water level changes in the lower Danube was done for two
significant periods (1965-1979 and 1998-2012).
Abstract: Social Avoidance is one of the most important
problems that face a good number of disabled students. It results from
the negative attitudes of non-disabled students, teachers and others.
Some of the past research has shown that non-disabled individuals
hold negative attitudes toward persons with disabilities. The present
study aims to alleviate Social Avoidance by applying the Cognitive
Behavioral Intervention. 24 Blind students aged 19–24 (university students) were randomly
chosen we compared an experimental group (consisted of 12
students) who went through the intervention program, with a control
group (12 students also) who did not go through such intervention.
We used the Social Avoidance and Distress Scale (SADS) to assess
social anxiety and distress behavior. The author used many
techniques of cognitive behavioral intervention such as modeling,
cognitive restructuring, extension, contingency contracts, selfmonitoring,
assertiveness training, role play, encouragement and
others. Statistically, T-test was employed to test the research
hypothesis. Result showed that there is a significance difference between the
experimental group and the control group after the intervention and
also at the follow up stages of the Social Avoidance and Distress
Scale. Also for the experimental group, there is a significance
difference before the intervention and the follow up stages for the
scale. Results showed that, there is a decrease in social avoidance.
Accordingly, cognitive behavioral intervention program was
successful in decreasing social avoidance for blind students.
Abstract: This paper discusses micrometeorological aspects of the urban climate in three cities in Western São Paulo State: Presidente Prudente, Assis and Iepê. Particular attention is paid to the method used to estimate the components of the energy balance at the surface. Estimates of convective fluxes showed that the Bowen ratio was an indicator of the local climate and that its magnitude varied between 0.3 and 0.7. Maximum values for the Bowen ratio occurred earlier in Iepê (11:00 am) than in Presidente Prudente (4:00 pm). The results indicate that the Bowen ratio is modulated by the radiation balance at the surface and by different clusters of vegetation.
Abstract: The purpose of the present work was to develop an innovative food product with good textural and sensorial characteristics. The product, a new type of bread, was prepared with wheat (90%) and lupin (10%) flours, without the addition of any conservatives. Several experiences were also done to find the most appropriate proportion of lupin flour. The optimized product was characterized considering the rheological, physical-chemical and sensorial properties. The water absorption of wheat flour with 10% of lupin was higher than that of the normal wheat flours, and Wheat Ceres flour presented the lower value, with lower dough development time and high stability time. The breads presented low moisture but a considerable water activity. The density of bread decreased with the introduction of lupin flour. The breads were quite white, and during storage the colour parameters decreased. The lupin flour clearly increased the number of alveolus, but the total area increased significantly just for the Wheat Cerealis bread. The addition of lupin flour increased the hardness and chewiness of breads, but the elasticity did not vary significantly. Lupin bread was sensorially similar to wheat bread produced with WCerealis flour, and the main differences are the crust rugosity, colour and alveolus characteristics.
Abstract: In the past few years, high consumption of soft drinks
has attracted negative attention world-wide due to its possible
adverse effects, leading the health conscious people to find
alternative nutraceutical or herbal health drinks. In the present study,
a nutraceutical soft drink was developed utilizing some easily
available and well known traditional herbs having nutritional
potential. The key ingredients were selected as bael, amla, lemon
juice, ashwagandha and poppy seeds based on their household routine
use in the summer with proven refreshing, cooling and energetic
feeling since ages. After several trials made, the final composition of
nutraceutical summer soft drink was selected as most suitable
combination based on the taste, physicochemical, microbial and
organoleptic point of view. The physicochemical analysis of the
prepared drink found to contain optimum level of titratable acidity,
total soluble solids and pH which were in accordance of the
commercial recommendations. There were no bacterial colonies
found in the product therefore found within limits. During the nine
point’s hedonic scale sensory evaluation, the drink was strongly liked
for colour, taste, flavour and texture. The formulation was found to
contain flavonoids (80mg/100ml), phenolics (103mg/100ml), vitamin
C (250mg/100ml) and has antioxidant potential (75.52%) apart from
providing several other essential vitamins, minerals and healthy
components. The developed nutraceutical drink provides an
economical and feasible option for the consumers with very good
taste combined with potential health benefits. The present drink is
potentially capable to replace the synthetic soft drinks available in the
market.
Abstract: A teeming set of doctors that graduated from various
universities within and outside Nigeria with the hope of practicing in
the country, has their hope shattered because of poor financing, lack
of medical equipments and a very weak healthcare systems. Such
hydra headed challenges, allows room for quackery which
increasingly contributes to the cause of mortality in Nigeria. With a
view of reversing the challenges of healthcare delivery and financing
in Nigeria, African Health Market for Equity (AHME), a project
funded by the Bill and Melinda Gates foundation [With contribution
from Department For International Development (DFID)] and
currently implemented in three African Countries (Nigeria, Kenya
and Ghana) over a Five (5) year period supports the healthcare sector
via Medical credit fund (MCF). The study examines the impact of
credit policy and medical credit funding on Nigerian health market.
Ordinary least square analysis, correlation and granger causality tests
were employed to measure the extent to which the Nigerian
healthcare market has been influenced. Medical credit fund
significantly and positively influenced average monthly turnover of
private healthcare providers and Commercial bank’s lending rate had
a weak relationship with access to credit/approved loans (13.46%).
The programme has so far made 13.91% progress, which is very
poor, considering the minimum targeted private health care providers
(437.6) and expected number of loan approvals (180.4) for the two
years. Medical credit policy in Nigeria should be revised to include
private healthcare providers in rural area for more positive impact
and increased returns. Good brand advert and sensitization of the
programme to stakeholders and health pressure group, and an
extension of the programme beyond five years is necessary to better
address the issues raised in the study.
Abstract: Second generation military Filipino Amerasians
comprise a formidable contemporary segment of the estimated
250,000-plus biracial Amerasians in the Philippines today. Overall,
they are a stigmatized and socioeconomically marginalized diaspora;
historically, they were abandoned or estranged by U.S. military
personnel fathers assigned during the century-long Colonial, Post-
World War II and Cold War Era of permanent military basing (1898-
1992). Indeed, U.S. military personnel are assigned in smaller
numbers in the Philippines today. This inquiry is an outgrowth of two
recent small sample studies. The first surfaced the impact of the U.S.
military prostitution system on formation of the ‘Derivative
Amerasian Family Construct’ on first generation Amerasians; a
second, qualitative case study suggested the continued effect of the
prostitution systems' destructive impetuous on second generation
Amerasians. The intent of this current qualitative, multiple-case study
was to actively seek out second generation sex industry toilers. The
purpose was to focus further on this human phenomenon in the postbasing
and post-military prostitution system eras. As background, the
former military prostitution apparatus has transformed into a modern
dynamic of rampant sex tourism and prostitution nationwide. This is
characterized by hotel and resorts offering unrestricted carnal access,
urban and provincial brothels (casas), discos, bars and pickup clubs,
massage parlors, local barrio karaoke bars and street prostitution. A
small case study sample (N = 4) of female and male second
generation Amerasians were selected. Sample formation employed a
non-probability ‘snowball’ technique drawing respondents from the
notorious Angeles, Metro Manila, Olongapo City ‘AMO Amerasian
Triangle’ where most former U.S. military installations were sited
and modern sex tourism thrives. A six-month study and analysis of
in-depth interviews of female and male sex laborers, their families
and peers revealed a litany of disturbing, and troublesome
experiences. Results showed profiles of debilitating human poverty,
history of family disorganization, stigmatization, social
marginalization and the ghost of the military prostitution system and
its harmful legacy on Amerasian family units. Emerging were testimonials of wayward young people ensnared in a maelstrom of
deep economic deprivation, familial dysfunction, psychological
desperation and societal indifference. The paper recommends that
more study is needed and implications of unstudied psychosocial and
socioeconomic experiences of distressed younger generations of
military Amerasians require specific research. Heretofore apathetic or
disengaged U.S. institutions need to confront the issue and formulate
activist and solution-oriented social welfare, human services and
immigration easement policies and alternatives. These institutions
specifically include academic and social science research agencies,
corporate foundations, the U.S. Congress, and Departments of State,
Defense and Health and Human Services, and Homeland Security
(i.e. Citizen and Immigration Services) It is them who continue to
endorse a laissez-faire policy of non-involvement over the entire
Filipino Amerasian question. Such apathy, the paper concludes,
relegates this consequential but neglected blood progeny to the status
of humiliating destitution and exploitation. Amerasians; thus, remain
entrapped in their former colonial, and neo-colonial habitat.
Ironically, they are unwitting victims of a U.S. American homeland
that fancies itself geo-politically as a strong and strategic military
treaty ally of the Philippines in the Western Pacific.
Abstract: Wire Electric Discharge Machining (WEDM) is
thermal machining process capable of machining very hard
electrically conductive material irrespective of their hardness.
WEDM is being widely used to machine micro scale parts with the
high dimensional accuracy and surface finish. The objective of this
paper is to optimize the process parameters of wire EDM to fabricate
the micro channels and to calculate the surface finish and material
removal rate of micro channels fabricated using wire EDM. The
material used is aluminum 6061 alloy. The experiments were
performed using CNC wire cut electric discharge machine. The effect
of various parameters of WEDM like pulse on time (TON) with the
levels (100, 150, 200), pulse off time (TOFF) with the levels (25, 35,
45) and current (IP) with the levels (105, 110, 115) were investigated
to study the effect on output parameter i.e. Surface Roughness and
Material Removal Rate (MRR). Each experiment was conducted
under different conditions of pulse on time, pulse off time and peak
current. For material removal rate, TON and Ip
were the most significant process parameter. MRR increases with the increase in
TON and Ip and decreases with the increase in TOFF. For surface
roughness, TON and Ip have the maximum effect and TOFF was found
out to be less effective.
Abstract: This paper discusses the question whether a person
diagnosed with dyslexia will necessarily have difficulty in reading
musical notes. The author specifies the characteristics of alphabet
reading in comparison to musical notation reading, and concludes
that there should be no contra-indication for teaching standard music
reading to children with dyslexia if an appropriate process is offered.
This conclusion is based on a long term case study and relies on two
main characteristics of music reading: (1) musical notation system is
a systematic, logical, relative set of symbols written on a staff; and
(2) music reading learning connected with playing a musical
instrument is a multi-sensory activity that combines sight, hearing,
touch, and movement. The paper describes music reading teaching
procedures, using soprano recorders, and provides unique teaching
methods that have been found to be effective for students who were
diagnosed with dyslexia. It provides theoretical explanations in
addition to guidelines for music education practices.
Abstract: Oxygen Reduction Reaction (ORR) performance of
iron and nitrogen co-doped porous carbon nanoparticles (Fe-NPC)
with various physical and (electro) chemical properties have been
investigated. Fe-NPC nanoparticles are synthesized via a facile
soft-templating procedure by using Iron (III) chloride hexa-hydrate as
iron precursor and aminophenol-formaldehyde resin as both carbon
and nitrogen precursor. Fe-NPC nanoparticles shows high surface area
(443.83 m2g-1), high pore volume (0.52 m3g-1), narrow mesopore size
distribution (ca. 3.8 nm), high conductivity (IG/ID=1.04), high kinetic
limiting current (11.71 mAcm-2) and more positive onset potential
(-0.106 V) compared to metal-free NPC nanoparticles (-0.295V)
which make it high efficient ORR metal-free catalysts in alkaline
solution. This study may pave the way of feasibly designing iron and
nitrogen containing carbon materials (Fe-N-C) for highly efficient
oxygen reduction electro-catalysis.
Abstract: Anammox is a novel and promising technology that has changed the traditional concept of biological nitrogen removal. The process facilitates direct oxidation of ammonical nitrogen under anaerobic conditions with nitrite as an electron acceptor without addition of external carbon sources. The present study investigated the feasibility of Anammox Hybrid Reactor (AHR) combining the dual advantages of suspended and attached growth media for biodegradation of ammonical nitrogen in wastewater. Experimental unit consisted of 4 nos. of 5L capacity AHR inoculated with mixed seed culture containing anoxic and activated sludge (1:1). The process was established by feeding the reactors with synthetic wastewater containing NH4-H and NO2-N in the ratio 1:1 at HRT (hydraulic retention time) of 1 day. The reactors were gradually acclimated to higher ammonium concentration till it attained pseudo steady state removal at a total nitrogen concentration of 1200 mg/l. During this period, the performance of the AHR was monitored at twelve different HRTs varying from 0.25-3.0 d with increasing NLR from 0.4 to 4.8 kg N/m3d. AHR demonstrated significantly higher nitrogen removal (95.1%) at optimal HRT of 1 day. Filter media in AHR contributed an additional 27.2% ammonium removal in addition to 72% reduction in the sludge washout rate. This may be attributed to the functional mechanism of filter media which acts as a mechanical sieve and reduces the sludge washout rate many folds. This enhances the biomass retention capacity of the reactor by 25%, which is the key parameter for successful operation of high rate bioreactors. The effluent nitrate concentration, which is one of the bottlenecks of anammox process was also minimised significantly (42.3-52.3 mg/L). Process kinetics was evaluated using first order and Grau-second order models. The first-order substrate removal rate constant was found as 13.0 d-1. Model validation revealed that Grau second order model was more precise and predicted effluent nitrogen concentration with least error (1.84±10%). A new mathematical model based on mass balance was developed to predict N2 gas in AHR. The mass balance model derived from total nitrogen dictated significantly higher correlation (R2=0.986) and predicted N2 gas with least error of precision (0.12±8.49%). SEM study of biomass indicated the presence of heterogeneous population of cocci and rod shaped bacteria of average diameter varying from 1.2-1.5 mm. Owing to enhanced NRE coupled with meagre production of effluent nitrate and its ability to retain high biomass, AHR proved to be the most competitive reactor configuration for dealing with nitrogen laden wastewater.
Abstract: Leishmaniasis is the collective name for a number of
diseases caused by protozoan flagellates of the genus Leishmania,
which is transmitted by Phlebotomine sandfly, the disease has diverse
clinical manifestations and found in many areas of the world,
particularly in Africa, Latin America, South and Central Asia, the
Mediterranean basin and the Middle East. This study was done to
assess primary health care physicians’ knowledge (PHP) and attitude
about leishmaniasis and to assess awareness of local inhabitants
about the disease and its vector in four areas in west Alexandria,
Egypt. It is a cross sectional survey that was conducted in four PHC
units in west Alexandria. All physicians currently working in these
units during the study period were invited to participate in the study;
only 20 PHP completed the questionnaire. 60 local inhabitants were
selected randomly from the four areas of the study, 15 from each
area; Data was collected through two different specially designed
questionnaires. Results showed that 11 (55%) percent of the
physicians had satisfactory knowledge; they answered more than 9
(60%) questions out of a total 14 questions about leishmaniasis and
sandfly. On the other hand when attitude of the primary health care
physicians about leishmaniasis was measured, results showed that 17
(85%) had good attitude and 3 (15%) had poor attitude. The second
questionnaire showed that the awareness of local inhabitants about
leishmaniasis and sandfly as a vector of the disease is poor and needs
to be corrected. (90%) of the interviewed inhabitants had not heard
about leishmaniasis, Only 3 (5%) of them said they know sandfly and
its role in transmission of leishmaniasis. Thus we conclude that
knowledge and attitudes of physicians are acceptable. However, there
is, room for improvement and could be done through formal training
courses and distribution of guidelines. In addition to raising the
awareness of primary health care physicians about the importance of
early detection and notification of cases of leishmaniasis, health
education for raising awareness of the public regarding the vector and
the disease is necessary because related studies have demonstrated
that for inhabitants to take enough protective measures against the
vector, they should perceive that it is responsible for causing a
disease.
Abstract: Adequate analgesia following caesarean section
decreases morbidity, hastens ambulation, improves patient outcome
and facilitates care of the newborn. Intrathecal magnesium, an
NMDA antagonist, has been shown to prolong analgesia without
significant side effects in healthy parturients. The aim of this study
was to evaluate the onset and duration of sensory and motor block,
hemodynamic effect, postoperative analgesia, and adverse effects of
magnesium or fentanyl given intrathecally with hyperbaric 0.5%
bupivacaine in patients with mild preeclampsia undergoing caesarean
section. Sixty women with mild preeclampsia undergoing elective
caesarean section were included in a prospective, double blind,
controlled trial. Patients were randomly assigned to receive spinal
anesthesia with 2 mL 0.5% hyperbaric bupivacaine with 12.5 μg
fentanyl (group F) or 0.1 ml of 50% magnesium sulphate (50 mg)
(group M) with 0.15ml preservative free distilled water. Onset,
duration and recovery of sensory and motor block, time to maximum
sensory block, duration of spinal anaesthesia and postoperative
analgesic requirements were studied. Statistical comparison was
carried out using the Chi-square or Fisher’s exact tests and
Independent Student’s t-test where appropriate. The onset of both
sensory and motor block was slower in the magnesium group. The
duration of spinal anaesthesia (246 vs. 284) and motor block (186.3
vs. 210) were significantly longer in the magnesium group. Total
analgesic top up requirement was less in group M. Hemodynamic
parameters were similar in both the groups. Intrathecal magnesium
caused minimal side effects. Since Fentanyl and other opioid
congeners are not available throughout the country easily,
magnesium with its easy availability and less side effect profile can
be a cost effective alternative to fentanyl in managing pregnancy
induced hypertension (PIH) patients given along with Bupivacaine
intrathecally in caesarean section.
Abstract: The increasing volume of solid waste generated,
collected and disposed daily complicate adequate management of
solid waste by relevant agency like Niger State Environmental
Protection Agency (NISEPA). In addition, the impacts of solid waste
on the natural environment and human livelihood require
identification of cost-effective ways for sustainable municipal waste
management in Nigeria. These signal the need for identifying
environment-friendly initiative and local solution to address the
problem of municipal solid waste. A research field was secured at
Pago, Minna, Niger State which is located in the guinea savanna belt
of Nigeria, within longitude 60 361 4311 - 4511 and latitude 90 291
37.6111 - .6211 N. Poultry droppings, decomposed household waste
manure and NPK treatments were used. The experimental field was
divided into three replications and four (4) treatments on each
replication making a total of twelve (12) plots. The treatments were
allotted using Randomized Complete Block Design (RCBD) and
Data collected was analyzed using SPSS software and RCBD. The
result depicts variation in plant height and number of leaves at 50%
flowering; Poultry dropping records the highest height while the
number of leaves for waste manure competes fairly well with NPK
treatment. Similarly, the varying treatments significantly increase
vegetable yield, as the control (non-treatment) records the least yield
for the three vegetable samples. Adoption of this organic manure for
cultivation does not only enhance environment quality and attainment
of food security but will contribute to local economic development,
poverty alleviation as well as social inclusion.
Abstract: Twin steel plates-concrete composite shear walls are
composed of a pair of steel plate layers and a concrete layer
sandwiched between them, which have the characteristics of both
reinforced concrete shear walls and steel plate shear walls. Twin steel
plates-composite shear walls contain very high ultimsate bearing
capacity and ductility, which have great potential to be applied in the
super high-rise buildings and special structures. In this paper, we
analyzed the basic characteristics and stress mechanism of the twin
steel plates-composite shear walls. Specifically, we analyzed the
effects of the steel plate thickness, wall thickness and concrete
strength on the bearing capacity of the twin steel plates-composite
shear walls. The analysis results indicate that: (1) the initial shear
stiffness and ultimate shear-carrying capacity is not significantly
affected by the thickness of concrete wall but by the class of concrete,
(2) both factors significantly impact the shear distribution of the
shear walls in ultimate shear-carrying capacity. The technique of twin
steel plates-composite shear walls has been successfully applied in
the construction of an 88-meter Huge Statue of Buddha located in
Hunan Province, China. The analysis results and engineering
experiences showed that the twin steel plates-composite shear walls
have great potential for future research and applications.
Abstract: The objective of this study was to evaluate the
effects of calving season on the production and economic efficiency
of dairy farms in Egypt. Our study was performed at dairy
production farms in the Alexandria, Behera, and Kafr El-Sheikh
provinces of Egypt from summer 2010 to winter 2013. The
randomly selected dairy farms had herds consisting of Baladi,
Holstein-Friesian, or cross-bred (Baladi × Holstein-Friesian) cows.
The data were collected from production records and responses to a
structured questionnaire. The average total return differed
significantly (P < 0.05) between the different cattle breeds and
calving seasons. The average total return was highest for the
Holstein- Friesian cows that calved in the winter (29106.42
EGP/cow/year), and it was lowest for Baladi cows that calved in the
summer (12489.79 EGP/cow/year). Differences in total returns
between the cows that calved in the winter or summer or between
the foreign and native breeds, as well as variations in calf prices,
might have contributed to the differences in milk yield. The average
net profit per cow differed significantly (P < 0.05) between the cattle
breeds and calving seasons. The average net profit values for the
Baladi cows that calved in the winter or summer were 2413 and
2994.96 EGP/cow/year, respectively, and those for the Holstein-
Friesian cows were 10744.17 and 7860.56 EGP/cow/year,
respectively, whereas those for the cross-bred cows were 10174.86
and 7571.33 EGP/cow/year, respectively. The variations in net profit
might have resulted from variation in the availability or price of feed
materials, milk prices, or sales volumes. Our results show that the
breed and calving season of dairy cows significantly affected the
economic efficiency of dairy farms in Egypt. The cows that calved
in the winter produced more milk than those that calved in the
summer, which may have been the result of seasonal influences,
such as temperature, humidity, management practices, and the type
of feed or green fodder available.
Abstract: The nickel-manganese (Ni-Mn) alloy coating prepared
from DC electrodeposition process in sulphamate bath was studied.
The effects of process parameters, such as current density and
electrolyte composition, on the cathodic current efficiency,
microstructure, internal stress and mechanical properties were
investigated. Because of its crucial effect on the application to the
electroforming of microelectronic components, the development of
low internal stress coating with high leveling power was emphasized.
It was found that both the coating’s manganese content and the
cathodic current efficiency increased with the raise in current density.
In addition, the internal stress of the deposited coating showed
compressive nature at low current densities while changed to tensile
one at higher current densities. Moreover, the metallographic
observation, X-ray diffraction measurement, and polarization curve
measurement were conducted. It was found that the Ni-Mn coating
consisted of nano-sized columnar grains and the maximum hardness of
the coating was associated with (111) preferred orientation in the
microstructure. The grain size was refined along with the increase in
the manganese content of the coating, which accordingly, raised its
hardness and resistance to annealing softening. In summary, the
Ni-Mn coating prepared at lower current density of 1-2 A/dm2 had low
internal stress, high leveling power, and better corrosion resistance.
Abstract: The global demand for long-tailed macaques for
medical experimentation has continued to increase. Fulfillment of
Indonesian export demands has been mostly from natural habitats,
based on a harvesting quota. This quota has been determined
according to the total catch for a given year, and not based on
consideration of any demographic parameters or physical
environmental factors with regard to the animal; hence threatening
the sustainability of the various populations. It is therefore necessary
to formulate a method for calculating a sustainable harvesting quota,
based on population parameters in natural habitats. Considering the
possibility of variations in habitat characteristics and population
parameters, a time series observation of demographic and
physical/biotic parameters, in various habitats, was performed on 13
groups of long-tailed macaques, distributed throughout the West
Java, Lampung and Yogyakarta areas of Indonesia. These provinces
were selected for comparison of the influence of human/tourism
activities. Data on population parameters that was collected included
data on life expectancy according to age class, numbers of
individuals by sex and age class, and ‘ratio of infants to reproductive
females’. The estimation of population growth was based on a
population dynamic growth model: the Leslie matrix. The harvesting
quota was calculated as being the difference between the actual
population size and the MVP (minimum viable population) for each
sex and age class. Observation indicated that there were variations within group size
(24–106 individuals), gender (sex) ratio (1:1 to 1:1.3), life expectancy
value (0.30 to 0.93), and ‘ratio of infants to reproductive females’
(0.23 to 1.56). Results of subsequent calculations showed that
sustainable harvesting quotas for each studied group of long-tailed
macaques, ranged from 29 to 110 individuals. An estimation model
of the MVP for each age class was formulated as Log Y = 0.315 +
0.884 Log Ni (number of individual on ith age class). This study also
found that life expectancy for the juvenile age class was affected by
the humidity under tree stands, and dietary plants’ density at sapling,
pole and tree stages (equation: Y=2.296 – 1.535 RH + 0.002 Kpcg –
0.002 Ktg – 0.001 Kphn, R2 = 89.6% with a significance value of
0.001). By contrast, for the sub-adult-adult age class, life expectancy
was significantly affected by slope (equation: Y=0.377 = 0.012 Kml,
R2 = 50.4%, with significance level of 0.007). The infant-toreproductive-
female ratio was affected by humidity under tree stands,
and dietary plant density at sapling and pole stages (equation: Y = -
1.432 + 2.172 RH – 0.004 Kpcg + 0.003 Ktg, R2 = 82.0% with
significance level of 0.001). This research confirmed the importance
of population parameters in determining the minimum viable
population, and that MVP varied according to habitat characteristics
(especially food availability). It would be difficult therefore, to
formulate a general mathematical equation model for determining a
harvesting quota for the species as a whole.
Abstract: Low Temperature Matrix Isolation - Electron
Paramagnetic Resonance (LTMI-EPR) Spectroscopy was utilized to
identify the species of iron oxide nanoparticles generated during the
oxidative pyrolysis of 1-methylnaphthalene (1-MN). The otherwise
gas-phase reactions of 1--MN were impacted by a polypropylenimine
tetra-hexacontaamine dendrimer complexed with iron (III) nitrate
nonahydrate diluted in air under atmospheric conditions. The EPR
fine structure of Fe (III)2O3 nanoparticles clusters, characterized by gfactors
of 2.00, 2.28, 3.76 and 4.37 were detected on a cold finger
maintained at 77 K after accumulation over a multitude of
experiments. Additionally, a high valence Fe (IV) paramagnetic
intermediate and superoxide anion-radicals, O2•- adsorbed on
nanoparticle surfaces in the form of Fe (IV) --- O2•- were detected
from the quenching area of Zone 1 in the gas-phase.