Abstract: Tomato powder has good potential as substitute of tomato paste and other tomato products. In order to protect physicochemical properties and nutritional quality of tomato during dehydration process, investigation was carried out using different drying methods and pretreatments. Solar drier and continuous conveyor (tunnel) drier were used for dehydration where as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl) selected for treatment.. lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning in addition to moisture, sugar and titrable acidity were studied. Results show that pre-treatment with CaCl2 and NaCl increased water removal and moisture mobility in tomato slices during drying of tomatoes. Where CaCl2 used along with KMS the NEB was recorded the least compared to other treatments and the best results were obtained while using the two chemicals in combination form. Storage studies in LDPE polymeric and metalized polyesters films showed less changes in the products packed in metallized polyester pouches and even after 6 months lycopene content did not decrease more than 20% as compared to the control sample and provide extension of shelf life in acceptable condition for 6 months. In most of the quality characteristics tunnel drier samples presented better values in comparison to solar drier.
Abstract: In this paper we propose new method for
simultaneous generating multiple quantiles corresponding to given
probability levels from data streams and massive data sets. This
method provides a basis for development of single-pass low-storage
quantile estimation algorithms, which differ in complexity, storage
requirement and accuracy. We demonstrate that such algorithms may
perform well even for heavy-tailed data.
Abstract: Experiments were carried out at the Faculty of Food
Technology of Latvia University of Agriculture (LLU). Soft cheese
Kleo produced in Latvia was packed in a biodegradable PLA without
barrierproperties and VC999 BioPack lidding film PLA, coated with
a barrier of pure silicon oxide (SiOx) and in combination with
modified atmosphere (MAP) the influence on the shelf life was
investigated and compared with some conventional (OPP, PE/PA,
PE/OPA and Multibarrier 60) polymer film impact. Modified
atmosphere consisted of carbon dioxide CO2 (E 290) 30% and
nitrogen N2 (E 941) 70%. The analyzable samples were stored at the
temperature of +4.0±0.5 °C up to 32 days- and analyzed before
packaging and in the 0, 5th, 11th, 15th, 18th, 22nd, 25th, 29th and 32nd
day of storage. The shelf life was extended along to 32 days, good
outside appearance and lactic acid aroma was observed.
Abstract: In countries with hot climates, air-conditioning forms
a large proportion of annual peak electrical demand, requiring
expansion of power plants to meet the peak demand, which goes
unused most of the time. Use of well-designed cool storage can offset
the peak demand to a large extent. In this study, an air conditioning
system with naturally stratified storage tank was designed,
constructed and tested. A new type of diffuser was designed and used
in this study. Factors that influence the performance of chilled water
storage tanks were investigated. The results indicated that stratified
storage tank consistently stratified well without any physical barrier.
Investigation also showed that storage efficiency decreased with
increasing flow rate due to increased mixing of warm and chilled
water. Diffuser design and layout primarily affected the mixing near
the inlet diffuser and the extent of this mixing had primary influence
on the shape of the thermocline. The heat conduction through tank
walls and through the thermocline caused widening of mixed volume.
Thermal efficiency of stratified storage tanks was as high as 90
percent, which indicates that stratified tanks can effectively be used
as a load management technique.
Abstract: This study assessed fish marketing as panacea towards
sustainable agriculture in Ogun State, Nigeria. Multi-stage sampling
technique was used in the selection of 150 fish marketers for this
study. Descriptive statistics were used for the objectives while
Product Pearson Moment Correlation was used to test the hypothesis.
Result of the findings revealed that the mean age of the respondents
was 38.60 years. Majority (93.33%) of the respondents had
acceptable levels of formal education. Many (44.00%) of the
respondents had spent 1-5 years in fish marketing. The average
quantity of fish sold in a day was 94.10kg. However, efficient fish
marketing were hindered by inadequate processing equipment,
storage rooms and ice holding facilities (86.67%). There was a
significant relationship between socio-economic characteristics and
profit realized from fish marketing (p < 0.05). It was recommended
that storage and warehousing facilities should be provided to the fish
marketers in the study area.
Abstract: In this paper, two versions of an iterative loopless
algorithm for the classical towers of Hanoi problem with O(1) storage complexity and O(2n) time complexity are presented. Based
on this algorithm the number of different moves in each of pegs with its direction is formulated.
Abstract: CO2 is the primary anthropogenic greenhouse gas,
accounting for 77% of the human contribution to the greenhouse
effect in 2004. In the recent years, global concentration of CO2 in the
atmosphere is increasing rapidly. CO2 emissions have an impact on
global climate change. Anthropogenic CO2 is emitted primarily from
fossil fuel combustion. Carbon capture and storage (CCS) is one
option for reducing CO2 emissions. There are three major approaches
for CCS: post-combustion capture, pre-combustion capture and
oxyfuel process. Post-combustion capture offers some advantages as
existing combustion technologies can still be used without radical
changes on them.
There are several post combustion gas separation and capture
technologies being investigated, namely; (a) absorption, (b)
cryogenic separation, (c) membrane separation (d) micro algal biofixation
and (e) adsorption. Apart from establishing new techniques,
the exploration of capture materials with high separation performance
and low capital cost are paramount importance. However, the
application of adsorption from either technology, require easily
regenerable and durable adsorbents with a high CO2 adsorption
capacity. It has recently been reported that the cost of the CO2
capture can be reduced by using this technology. In this paper, the
research progress (from experimental results) in adsorbents for CO2
adsorption, storage, and separations were reviewed and future
research directions were suggested as well.
Abstract: The aim of current research was to investigate ASLT method suitability for accelerated beer shelf-life determination. The research was accomplished on popular Latvian beer: light filtrated and unfiltered pasteurized beer with alcohol content 5.2%; dark filtrated pasteurized beer with alcohol content 4.2% with shelf-life five months. Bottled in dark glass bottles beer samples were storage during 20 weeks at several temperature regimes: +10±1 °C, +20±1 °C, +30±1 °C, +40±1 °C. Samples quality parameters as physically-chemical and microbiological was tested every two weeks using standard methods. It is possible to determine beer shelf-life rapidly during storage at +30±1 °C for filtered pasteurized light beer by 2.5 times, unfiltered pasteurized light beer by 1.4 times and for filtered pasteurized dark beer by 1.7 times. During preset experiments it was proved, that it is possible to determine beer shelf-life rapidly using ASLT method if beer storage temperature could be increased by +10±1 °C.
Abstract: This study include the effect of strain and storage
period and their interaction on some quantitative and qualitative traits
and percentages of the egg components in the eggs collected at the
start of production (at age 24 weeks). Eggs were divided into three
storage periods (1, 7 and 14) days under refrigerator temperature (5-
7)0C. Fifty seven eggs obtained randomly from each strain including
Isa Brown and Lohman White. General Linear Model within
SAS programme was used to analyze the collected data
and correlations between the studied traits were calculated for each
strain.Average egg weight (EW), Haugh Unit (HU), yolk index (YI),
yolk % (HP), albumin % (AP) and yolk to albumin ratio (YAR) was
56.629 gm, 87.968 %, 0.493, 22.13%, 67.74% and 32.76
respectively. Egg produced from ISA Brown surpassed those
produced by Lohman White significantly (P
Abstract: New advancement of technology and never satisfying demands of the civilization are putting huge pressure on the natural fuel resources and these resources are at a constant threat to its sustainability. To get the best out of the automobile, the optimum balance between performance and fuel economy is important. In the present state of art, either of the above two aspects are taken into mind while designing and development process which puts the other in the loss as increase in fuel economy leads to decrement in performance and vice-versa. In-depth observation of the vehicle dynamics apparently shows that large amount of energy is lost during braking and likewise large amount of fuel is consumed to reclaim the initial state, this leads to lower fuel efficiency to gain the same performance. Current use of Kinetic Energy Recovery System is only limited to sports vehicles only because of the higher cost of this system. They are also temporary in nature as power can be squeezed only during a small time duration and use of superior parts leads to high cost, which results on concentration on performance only and neglecting the fuel economy. In this paper Kinetic Energy Recovery System for storing the power and then using the same while accelerating has been discussed. The major storing element in this system is a Flat Spiral Spring that will store energy by compression and torsion.
The use of spring ensure the permanent storage of energy until used by the driver unlike present mechanical regeneration system in which the energy stored decreases with time and is eventually lost. A combination of internal gears and spur gears will be used in order to make the energy release uniform which will lead to safe usage. The system can be used to improve the fuel efficiency by assisting in overcoming the vehicle’s inertia after braking or to provide instant acceleration whenever required by the driver. The performance characteristics of the system including response time, mechanical efficiency and overall increase in efficiency are demonstrated. This technology makes the KERS (Kinetic Energy Recovery System) more flexible and economical allowing specific application while at the same time increasing the time frame and ease of usage.
Abstract: Ipomoea batatas (Sweetpotato) is currently ranked
sixth in the total world food production and are planted mainly for
their storage roots. The present study was undertaken to evaluate and
compare the antioxidant properties of the leaf and carotenoids extract
from the Ipomoea batatas var. Oren leaves. Total flavonoids in the
leaf extract was 144.6 ± 40.5 μg/g compared to 114.86 ± 4.35 μg/g
catechin equivalent in the carotenoids extract. Total polyphenols in
the leaf extracts (3.470 ± 0.024 GAE g/100g DW) was slightly higher
compared to carotenoids extract (2.994 ± 0.078 GAE g/100g DW).
The carotenoids extract marked a higher radical scavenging capacity
with the IC50= 491.86 μg/ml compared to leaf extract (IC50= 545.39
μg/ml). Concentration-dependent reducing activity was observed for
both extracts. Thus, the carotenoids extraction process retained most
of the antioxidant capacity from the leaves and can be made into
potential natural yellow dye with antioxidant property.
Abstract: This study analyzes characteristics determining
member’s willingness to invest in cooperatives using ordered logit
model. The data were collected in a field survey among 122
cooperative members in north-central China. The descriptive analysis
of survey evidence suggests that cooperatives in China generally
having poor ability to deliver the processing services related to
product package, grading, and storage, performing worse in
profitability, inability of providing returns to capital and obtaining
agricultural loan. The regression results demonstrate that members’
farm size, their satisfaction with cooperative price preferential
services, attitudes toward cooperative operational scale and
development potential have statistically significant impact on
willingness to invest.
Abstract: The implementation of the new software and hardware-s technologies for tritium processing nuclear plants, and especially those with an experimental character or of new technology developments shows a coefficient of complexity due to issues raised by the implementation of the performing instrumentation and equipment into a unitary monitoring system of the nuclear technological process of tritium removal. Keeping the system-s flexibility is a demand of the nuclear experimental plants for which the change of configuration, process and parameters is something usual. The big amount of data that needs to be processed stored and accessed for real time simulation and optimization demands the achievement of the virtual technologic platform where the data acquiring, control and analysis systems of the technological process can be integrated with a developed technological monitoring system. Thus, integrated computing and monitoring systems needed for the supervising of the technological process will be executed, to be continued with the execution of optimization system, by choosing new and performed methods corresponding to the technological processes within the tritium removal processing nuclear plants. The developing software applications is executed with the support of the program packages dedicated to industrial processes and they will include acquisition and monitoring sub-modules, named “virtually" as well as the storage sub-module of the process data later required for the software of optimization and simulation of the technological process for tritium removal. The system plays and important role in the environment protection and durable development through new technologies, that is – the reduction of and fight against industrial accidents in the case of tritium processing nuclear plants. Research for monitoring optimisation of nuclear processes is also a major driving force for economic and social development.
Abstract: The objective of the research was to evaluate the
hardness stability of milk pomade sweets packed in several
packaging materials (OPP, Multibarrier 60 HFP, BIALON 65
HFP, BIALON 50 HFP, ECOLEAN) by several packaging
technologies – modified atmosphere (MAP) (consisting of
30% CO2+70% N2; 30% N2+70% CO2 and 100% CO2) and
control – in air ambiance. Samples were stored at the room
temperature +21±1 °C. The studies of the samples were
carried out before packaging and after 2, 4, 6, 8, and 10
storage weeks.
Abstract: A novel three-phase active power filter (APF) circuit with photovoltaic (PV) system to improve the quality of service and to reduce the capacity of energy storage capacitor is presented. The energy balance concept and sampling technique were used to simplify the calculation algorithm for the required utility source current and to control the voltage of the energy storage capacitor. The feasibility was verified by using the Pspice simulations and experiments. When the APF mode was used during non-operational period, not only the utilization rate, power factor and power quality could be improved, but also the capacity of energy storage capacitor could sparing. As the results, the advantages of the APF circuit are simplicity of control circuits, low cost, and good transient response.
Abstract: A renewable energy system discussed in this paper is
a stand-alone wind-hydrogen system for a remote island in Australia.
The analysis of an existing wind-diesel power system was performed.
Simulation technique was used to model the power system currently
employed on the island, and simulated different configurations of
additional hydrogen energy system. This study aims to determine the
suitable hydrogen integrated configuration to setting up the prototype
system for the island, which helps to reduce the diesel consumption
on the island. A set of configurations for the hydrogen system and
associated parameters that consists of wind turbines, electrolysers,
hydrogen internal combustion engines, and storage tanks has been
purposed. The simulation analyses various configurations that
perfectly balances the system to meet the demand on the island.
Abstract: To compress, improve bit error performance and also enhance 2D images, a new scheme, called Iterative Cellular-Turbo System (IC-TS) is introduced. In IC-TS, the original image is partitioned into 2N quantization levels, where N is denoted as bit planes. Then each of the N-bit-plane is coded by Turbo encoder and transmitted over Additive White Gaussian Noise (AWGN) channel. At the receiver side, bit-planes are re-assembled taking into consideration of neighborhood relationship of pixels in 2-D images. Each of the noisy bit-plane values of the image is evaluated iteratively using IC-TS structure, which is composed of equalization block; Iterative Cellular Image Processing Algorithm (ICIPA) and Turbo decoder. In IC-TS, there is an iterative feedback link between ICIPA and Turbo decoder. ICIPA uses mean and standard deviation of estimated values of each pixel neighborhood. It has extra-ordinary satisfactory results of both Bit Error Rate (BER) and image enhancement performance for less than -1 dB Signal-to-Noise Ratio (SNR) values, compared to traditional turbo coding scheme and 2-D filtering, applied separately. Also, compression can be achieved by using IC-TS systems. In compression, less memory storage is used and data rate is increased up to N-1 times by simply choosing any number of bit slices, sacrificing resolution. Hence, it is concluded that IC-TS system will be a compromising approach in 2-D image transmission, recovery of noisy signals and image compression.
Abstract: This paper presents strategies for dynamically creating, managing and removing mesh cells during computations in the context of the Material Point Method (MPM). The dynamic meshing approach has been developed to help address problems involving motion of a finite size body in unbounded domains in which the extent of material travel and deformation is unknown a priori, such as in the case of landslides and debris flows. The key idea is to efficiently instantiate and search only cells that contain material points, thereby avoiding unneeded storage and computation. Mechanisms for doing this efficiently are presented, and example problems are used to demonstrate the effectiveness of dynamic mesh management relative to alternative approaches.
Abstract: 28 healthy adult Maradi bucks were used to evaluate
sperm production and sperm storage capacity in the breed. Daily
sperm production (DSP) averaged 0.55±0.05x109, while the daily
sperm production/g (DSP/g) was 1.37±0.12 x107. Gonadal sperm
reserve was 1.99±0.18 x109, while the caput, upper corpus and lower
corpus averaged 0.58±0.04 x109, 0.36±0.02 x109 and 0.33±0.08 x109
respectively. The proximal cauda, mid cauda, distal cauda and ductus
deferens had values of 0.68±0.10 x109, 1.23±0.16 x109,1.87±0.
x109and 0.17±0.05 x109 respectively. The relative contributions of
the respective epididymal sections and ductus deferens to the total
extragonadal sperm reserves were, 11.11%, 6.89%, 6.32%, 13.03%,
23.56%, 35.82% and 3.26% respectively. Gonadal sperm reserves
were significantly higher (p0.05) to
mid cauda and distal cauda epididymal reserves.
Abstract: In-place sorting algorithms play an important role in many fields such as very large database systems, data warehouses, data mining, etc. Such algorithms maximize the size of data that can be processed in main memory without input/output operations. In this paper, a novel in-place sorting algorithm is presented. The algorithm comprises two phases; rearranging the input unsorted array in place, resulting segments that are ordered relative to each other but whose elements are yet to be sorted. The first phase requires linear time, while, in the second phase, elements of each segment are sorted inplace in the order of z log (z), where z is the size of the segment, and O(1) auxiliary storage. The algorithm performs, in the worst case, for an array of size n, an O(n log z) element comparisons and O(n log z) element moves. Further, no auxiliary arithmetic operations with indices are required. Besides these theoretical achievements of this algorithm, it is of practical interest, because of its simplicity. Experimental results also show that it outperforms other in-place sorting algorithms. Finally, the analysis of time and space complexity, and required number of moves are presented, along with the auxiliary storage requirements of the proposed algorithm.