Abstract: Equilibrium and rate based models have been applied
in the simulation of methyl tertiary-butyl ether (MTBE) synthesis
through reactive distillation. Temperature and composition profiles
were compared for both the models and found that both the profiles
trends, though qualitatively similar are significantly different
quantitatively. In the rate based method (RBM), multicomponent
mass transfer coefficients have been incorporated to describe
interphase mass transfer. MTBE mole fraction in the bottom stream is
found to be 0.9914 in the Equilibrium Model (EQM) and only 0.9904
for RBM when the same column configuration was preserved. The
individual tray efficiencies were incorporated in the EQM and
simulations were carried out. Dynamic simulation have been also
carried out for the two column configurations and compared.
Abstract: This paper explains the cause of nonlinearity in floor
attenuation hither to left unexplained. The performance degradation
occurring in air interface for GSM signals is quantitatively analysed
using the concept of Radiating Columns of buildings. The signal
levels were measured using Wireless Network Optimising Drive Test
Tool (E6474A of Agilent Technologies). The measurements were
taken in reflected signal environment under usual fading conditions
on actual GSM signals radiated from base stations. A mathematical
model is derived from the measurements to predict the GSM signal
levels in different floors. It was applied on three buildings and found
that the predicted signal levels deviated from the measured levels
with in +/- 2 dB for all floors. It is more accurate than the prediction
models based on Floor Attenuation Factor. It can be used for
planning proper indoor coverage in multi storey buildings.
Abstract: This paper presents a comparative study of statistical methods for the multi-response surface optimization of a cryogenic freezing process. Taguchi design and analysis and steepest ascent methods based on the desirability function were conducted to ascertain the influential factors of a cryogenic freezing process and their optimal levels. The more preferable levels of the set point, exhaust fan speed, retention time and flow direction are set at -90oC, 20 Hz, 18 minutes and Counter Current, respectively. The overall desirability level is 0.7044.
Abstract: One of the approaches to democratization is the fostering of civil society organizations. In Africa, civil society organizations did not fully play their role in the continent-s democratization process due to many factors including the repressive regulations imposed on them by governing parties. In Ethiopia, for the first time in the country-s political history, the civil society played a very active role in the 2005 multi-party election. The involvement of the civil society in this election has far-reaching consequences. One of the objectives of this paper is to assess the consequences of such involvement for both the civil society and the political society in the country. The paper also examines the peculiarities of civil society formation in Africa in general, and in Ethiopia in particular by assessing both the “traditional" and “modern" civil society organizations.
Abstract: In this paper, we present a method for edge
segmentation of satellite images based on 2-D Phase Congruency
(PC) model. The proposed approach is composed by two steps: The
contextual non linear smoothing algorithm (CNLS) is used to smooth
the input images. Then, the 2D stretched Gabor filter (S-G filter)
based on proposed angular variation is developed in order to avoid
the multiple responses in the previous work. An assessment of our
proposed method performance is provided in terms of accuracy of
satellite image edge segmentation. The proposed method is compared
with others known approaches.
Abstract: Understanding driving behavior is a complicated
researching topic. To describe accurate speed, flow and density of a
multiclass users traffic flow, an adequate model is needed. In this
study, we propose the concept of standard passenger car equivalent
(SPCE) instead of passenger car equivalent (PCE) to estimate the
influence of heavy vehicles and slow cars. Traffic cellular automata
model is employed to calibrate and validate the results. According to
the simulated results, the SPCE transformations present good
accuracy.
Abstract: The aim of the article is extending and developing
econometrics and network structure based methods which are able to
distinguish price manipulation in Tehran stock exchange. The
principal goal of the present study is to offer model for
approximating price manipulation in Tehran stock exchange. In order
to do so by applying separation method a sample consisting of 397
companies accepted at Tehran stock exchange were selected and
information related to their price and volume of trades during years
2001 until 2009 were collected and then through performing runs
test, skewness test and duration correlative test the selected
companies were divided into 2 sets of manipulated and non
manipulated companies. In the next stage by investigating
cumulative return process and volume of trades in manipulated
companies, the date of starting price manipulation was specified and
in this way the logit model, artificial neural network, multiple
discriminant analysis and by using information related to size of
company, clarity of information, ratio of P/E and liquidity of stock
one year prior price manipulation; a model for forecasting price
manipulation of stocks of companies present in Tehran stock
exchange were designed. At the end the power of forecasting models
were studied by using data of test set. Whereas the power of
forecasting logit model for test set was 92.1%, for artificial neural
network was 94.1% and multi audit analysis model was 90.2%;
therefore all of the 3 aforesaid models has high power to forecast
price manipulation and there is no considerable difference among
forecasting power of these 3 models.
Abstract: Recently, we have presented an initial implementation
of a model agent-based e-commerce system, which utilized a simple
price negotiation mechanism–English Auction. In this note we
discuss how a Dutch Auction involving multiple units of a product
can be included in our system. We present UML diagrams of
agents involved in price negotiations and briefly discuss rule-based
mechanism exemplifying Dutch Auction.
Abstract: One of the major problems in genomic field is to perform sequence comparison on DNA and protein sequences. Executing sequence comparison on the DNA and protein data is a computationally intensive task. Sequence comparison is the basic step for all algorithms in protein sequences similarity. Parallel computing is an attractive solution to provide the computational power needed to speedup the lengthy process of the sequence comparison. Our main research is to enhance the protein sequence algorithm using dynamic programming method. In our approach, we parallelize the dynamic programming algorithm using multithreaded program to perform the sequence comparison and also developed a distributed protein database among many PCs using Remote Method Interface (RMI). As a result, we showed how different sizes of protein sequences data and computation of scoring matrix of these protein sequence on different number of processors affected the processing time and speed, as oppose to sequential processing.
Abstract: The machining of Carbon Fiber Reinforced Plastics
has come to constitute a significant challenge for many fields of
industry. The resulting surface finish of machined parts is of primary
concern for several reasons, including contact quality and impact on
the assembly. Therefore, the characterization and prediction of
roughness based on machining parameters are crucial for costeffective
operations. In this study, a PCD tool comprised of two
straight flutes was used to trim 32-ply carbon fiber laminates in a bid
to analyze the effects of the feed rate and the cutting speed on the
surface roughness. The results show that while the speed has but a
slight impact on the surface finish, the feed rate for its part affects it
strongly. A detailed study was also conducted on the effect of fiber
orientation on surface roughness, for quasi-isotropic laminates used
in aerospace. The resulting roughness profiles for the four-ply
orientation lay-up were compared, and it was found that fiber angle is
a critical parameter relating to surface roughness. One of the four
orientations studied led to very poor surface finishes, and
characteristic roughness profiles were identified and found to only
relate to the ply orientations of multilayer carbon fiber laminates.
Abstract: Capacity and efficiency of any refrigerating system
diminish rapidly as the difference between the evaporating and
condensing temperature is increased by reduction in the evaporator
temperature. The single stage vapour compression refrigeration
system is limited to an evaporator temperature of -40 0C. Below
temperature of -40 0C the either cascade refrigeration system or multi
stage vapour compression system is employed. Present work
describes thermal design of main three heat exchangers namely
condenser (HTS), cascade condenser and evaporator (LTS) of
R404A-R508B and R410A-R23 cascade refrigeration system. Heat
transfer area of condenser (HTS), cascade condenser and evaporator
(LTS) for both systems have been compared and the effect of
condensing and evaporating temperature on heat-transfer area for
both systems have been studied under same operating condition. The
results shows that the required heat-transfer area of condenser and
cascade condenser for R410A-R23 cascade system is lower than the
R404A-R508B cascade system but heat transfer area of evaporator is
similar for both the system. The heat transfer area of condenser and
cascade condenser decreases with increase in condensing temperature
(Tc), whereas the heat transfer area of cascade condenser and
evaporator increases with increase in evaporating temperature (Te).
Abstract: A new and highly efficient architecture for elliptic curve scalar point multiplication which is optimized for a binary field recommended by NIST and is well-suited for elliptic curve cryptographic (ECC) applications is presented. To achieve the maximum architectural and timing improvements we have reorganized and reordered the critical path of the Lopez-Dahab scalar point multiplication architecture such that logic structures are implemented in parallel and operations in the critical path are diverted to noncritical paths. With G=41, the proposed design is capable of performing a field multiplication over the extension field with degree 163 in 11.92 s with the maximum achievable frequency of 251 MHz on Xilinx Virtex-4 (XC4VLX200) while 22% of the chip area is occupied, where G is the digit size of the underlying digit-serial finite field multiplier.
Abstract: In this study, we introduced a communication system
where human body was used as medium through which data were
transferred. Multiple biosignal sensing units were attached to a subject
and wireless personal area network was formed. Data of the sensing
units were shared among them. We used wideband pulse
communication that was simple, low-power consuming and high data
rated. Each unit functioned as independent communication device or
node. A method of channel search and communication among the
modes was developed. A protocol of carrier sense multiple
access/collision detect was implemented in order to avoid data
collision or interferences. Biosignal sensing units should be located at
different locations due to the nature of biosignal origin. Our research
provided a flexibility of collecting data without using electrical wires.
More non-constrained measurement was accomplished which was
more suitable for u-Health monitoring.
Abstract: The purpose of this study is to examine the selfefficacy
and life satisfaction levels of students receiving education in
schools of physical education and sports. The population of the study
consisted 263 students, among which 154 were male and 109 were
female ( X age=19,4905 + 2,5605), that received education in the
schools of physical education and sports of Selcuk University, Inonu
University, Gazi University and Karamanoglu Mehmetbey
University. In order to achieve the purpose of the study, the selfefficacy
scale, which was developed by Jarrusselam and Shwarzer
(1981) [1] and adapted to Turkish by Yesillay (1993) [2], and the
life satisfaction scale, developed by Diener, Emmos, Larsen and
Griffin (1985) [3] and adapted to Turkish by Kokler (1991) [4], were
utilized.For analyzing and interpreting data Kolmogorov-Smirnov
test, t-test and one way anova test were used, while for determining
the difference between the groups Tukey test and Multiple Linear
Regression test were employed and significance was accepted at
P
Abstract: The aim of this work is to investigate on the internalflow
patterns in a plate heat exchanger channel, which affect the
rate of sedimentation fouling on the heat transfer surface of the
plate heat exchanger. The research methodologies were the
computer simulation using Computational Fluid Dynamics (CFD)
and the experimental works. COMSOL MULTIPHYSICS™
Version 3.3 was used to simulate the velocity flow fields to verify
the low and high flow regions. The results from the CFD technique
were then compared with the images obtained from the
experiments in which the fouling test rig was set up with a singlechannel
plate heat exchanger to monitor the fouling of calcium
carbonate. Two parameters were varied i.e., the crossing angle of
the two plate: 55/55, 10/10, and 55/10 degree, and the fluid flow
rate at the inlet: 0.0566, 0.1132 and 0.1698 m/s. The type of plate
“GX-12" (the surface area 0.12 m2, the depth 2.9 mm, the width of
fluid flow 215 mm and the thickness of stainless plate of 0.5 mm)
was used in this study. The results indicated that the velocity
distribution for the case of 55/55 degree seems to be very well
organized when compared with the others. Also, an increase in the
inlet velocity resulted in the reduction of fouling rate on the surface
of plate heat exchangers.
Abstract: In this paper, we propose a method to reduce the
various kinds of noise while gathering and recording the
electrocardiogram (ECG) signal. Because of the defects of former
method in the noise elimination of ECG signal, we use translation
invariant (TI) multiwavelet denoising method to the noise elimination.
The advantage of the proposed method is that it may not only remain
the geometrical characteristics of the original ECG signal and keep the
amplitudes of various ECG waveforms efficiently, but also suppress
impulsive noise to some extent. The simulation results indicate that the
proposed method are better than former removing noise method in
aspects of remaining geometrical characteristics of ECG signal and the
signal-to-noise ratio (SNR).
Abstract: In this paper, we research the standard 13-point difference schemes for solving the biharmonic equation. Heuristic method is applied to judging the stability of multi-level difference schemes of the biharmonic equation. It is showed that the standard 13-point difference schemes are stable.
Abstract: Categorical data based on description of the
agricultural landscape imposed some mathematical and analytical
limitations. This problem however can be overcome by data
transformation through coding scheme and the use of non-parametric
multivariate approach. The present study describes data
transformation from qualitative to numerical descriptors. In a
collection of 103 random soil samples over a 60 hectare field,
categorical data were obtained from the following variables: levels of
nitrogen, phosphorus, potassium, pH, hue, chroma, value and data on
topography, vegetation type, and the presence of rocks. Categorical
data were coded, and Spearman-s rho correlation was then calculated
using PAST software ver. 1.78 in which Principal Component
Analysis was based. Results revealed successful data transformation,
generating 1030 quantitative descriptors. Visualization based on the
new set of descriptors showed clear differences among sites, and
amount of variation was successfully measured. Possible applications
of data transformation are discussed.
Abstract: A handful of propagation textbooks that discuss radio frequency (RF) propagation models merely list out the models and perhaps discuss them rather briefly; this may well be frustrating for the potential first time modeller who's got no idea on how these models could have been derived. This paper fundamentally provides an overture in modelling the radio channel. Explicitly, for the modelling practice discussed here, signal strength field measurements had to be conducted beforehand (this was done at 469 MHz); to be precise, this paper primarily concerns empirically/statistically modelling the radio channel, and thus provides results obtained from empirically modelling the environments in question. This paper, on the whole, proposes three propagation models, corresponding to three experimented environments. Perceptibly, the models have been derived by way of making the most use of statistical measures. Generally speaking, the first two models were derived via simple linear regression analysis, whereas the third have been originated using multiple regression analysis (with five various predictors). Additionally, as implied by the title of this paper, both indoor and outdoor environments have been experimented; however, (somewhat) two of the environments are neither entirely indoor nor entirely outdoor. The other environment, however, is completely indoor.
Abstract: Space-time block codes (STBC) and spatial multiplexing
(SM) are promising techniques that effectively exploit multipleinput
multiple-output (MIMO) transmission to achieve more reliable
communication and a higher multiplexing rate, respectively. In this
paper, we study a practical design for hybrid scheme with multi-input
multi-output orthogonal frequency division multiplexing (MIMOOFDM)
systems to flexibly maximize the tradeoff between diversity
and multiplexing gains. Unlike the existing STBC and SM designs
which are suitable for the integer multiplexing rate, the proposed
design can achieve arbitrary number of multiplexing rate.