Abstract: In the present paper, Fatigue life assessment of an
anti-roll bar component of a passenger vehicle, is investigated by
ANSYS 11 software. A stress analysis is also carried out by the
finite element technique for the determination of highly stressed
regions on the bar. Anti-roll bar is a suspension element used at the
front, rear, or at both ends of a car that reduces body roll by resisting
any unequal vertical motion between the pair of wheels to which it is
connected. As a first stage, fatigue damage models proposed by some
well-known references and the corresponding assumptions are
discussed and some enhancements are proposed. Then, fracture
analysis of an anti-roll bar of an automobile is carried out. The
analysed type of the anti-roll bar is especially important as many
cases are reported about the fracture after a 100,000 km of travel
fatigue and fracture conditions. This paper demonstrates fatigue life
of an anti-roll bar and then evaluated by experimental analytically
results from other researcher.
Abstract: This paper addresses the problem of trajectory
tracking control of an underactuated autonomous underwater vehicle
(AUV) in the horizontal plane. The underwater vehicle under
consideration is not actuated in the sway direction, and the system
matrices are not assumed to be diagonal and linear, as often found in
the literature. In addition, the effect of constant bias of environmental
disturbances is considered. Using backstepping techniques and the
tracking error dynamics, the system states are stabilized by forcing
the tracking errors to an arbitrarily small neighborhood of zero. The
effectiveness of the proposed control method is demonstrated through
numerical simulations. Simulations are carried out for an
experimental vehicle for smooth, inertial, two dimensional (2D)
reference trajectories such as constant velocity trajectory (a circle
maneuver – constant yaw rate), and time varying velocity trajectory
(a sinusoidal path – sinusoidal yaw rate).
Abstract: In this paper an efficient implementation of Ripemd-
160 hash function is presented. Hash functions are a special family
of cryptographic algorithms, which is used in technological
applications with requirements for security, confidentiality and
validity. Applications like PKI, IPSec, DSA, MAC-s incorporate
hash functions and are used widely today. The Ripemd-160 is
emanated from the necessity for existence of very strong algorithms
in cryptanalysis. The proposed hardware implementation can be
synthesized easily for a variety of FPGA and ASIC technologies.
Simulation results, using commercial tools, verified the efficiency of
the implementation in terms of performance and throughput. Special
care has been taken so that the proposed implementation doesn-t
introduce extra design complexity; while in parallel functionality was
kept to the required levels.
Abstract: BEAMnrc was used to calculate the spectrum and
HVL for X-ray Beam during low energy X-ray radiation using tube model: SRO 33/100 /ROT 350 Philips. The results of BEAMnrc
simulation and measurements were compared to the IPEM report
number 78 and SpekCalc software. Three energies 127, 103 and 84
Kv were used. In these simulation a tungsten anode with 1.2 mm for
Be window were used as source. HVLs were calculated from
BEAMnrc spectrum with air Kerma method for four different filters.
For BEAMnrc one billion particles were used as original particles for
all simulations. The results show that for 127 kV, there was
maximum 5.2 % difference between BEAMnrc and Measurements
and minimum was 0.7% .the maximum 9.1% difference between
BEAMnrc and IPEM and minimum was 2.3% .The maximum
difference was 3.2% between BEAMnrc and SpekCal and minimum
was 2.8%. The result show BEAMnrc was able to satisfactory predict
the quantities of Low energy Beam as well as high energy X-ray
radiation.
Abstract: This paper provides an introduction into the
evolution of information and communication technology and illustrates its usage in the work domain. The paper is sub-divided into two parts. The first part gives an overview over the different
phases of information processing in the work domain. It starts by
charting the past and present usage of computers in work
environments and shows current technological trends, which are likely to influence future business applications. The second part
starts by briefly describing, how the usage of computers changed business processes in the past, and presents first Ambient
Intelligence applications based on identification and localization
information, which are already used in the production and retail sector. Based on current systems and prototype applications, the
paper gives an outlook of how Ambient Intelligence technologies could change business processes in the future.
Abstract: In order to evaluate the Effects of dual inoculation of
Azotobacter and Mycorrhiza with Nitrogen and Phosphorus levels on
yield and yield components of spring safflower, this study was
carried out in field of Farahan university in Markazi province in
2007. A factorial in a randomized complete block design with three
replications was used inoculation of Azotobacter (with inoculation
and without inoculation) and Mycorrhiza (with inoculation and
without inoculation ) with Nitrogen and Phosphorus levels [F0= N0+
P0 (kg.ha-1), F1= N50+ P25(kg.ha-1), F2= N100+ P50(kg.ha-1) and
F3= N150+ P75 (kg.ha-1)] on spring safflower (cultivar IL-111). In
this study characteristics such as: Harvest index, Hectolitre weight,
Root dry weight, Seed yield, Mycorrhizal Colonization Root,
Number of days to maturity were assessed. Results indicated that
treatment (A0M1F3) with grain yield (1556 kg.ha-1) and treatment
(A0M1F0) with grain yield (918 kg.ha-1) were significantly superior
to the other treatments and according to calculated, inoculation seeds
in plantig date with Azotobacter and Mycorrhiza to cause increase
grain yield about 5/38 percentage. we can by inoculation safflower
seeds with Azotobacter and Mycorrhiza too easily at the time sowing
date. The purpose of this research, study and evaluation the role of
biological fixation N and P, to provide for feeds plants.
Abstract: In wireless networks, bandwidth is scare resource and it is essential to utilize it effectively. This paper analyses effects of using different bandwidth management techniques on the network performances of the Wireless Local Area Networks (WLANs) that use hybrid load balancing scheme. In particular, we study three bandwidth management schemes, namely Complete Sharing (CS), Complete Partitioning (CP), and Partial Sharing (PS). Performances of these schemes are evaluated by simulation experiments in term of percentage of network association blocking. Our results show that the CS scheme can provide relatively low blocking percentage in various network traffic scenarios whereas the PS scheme can enhance quality of services of the multimedia traffic with rather small expenses on the blocking percentage of the best effort traffic.
Abstract: With the advent of new technologies, factors related to
mental health in e-workspaces are taken into consideration more than
ever. Studies have revealed that one of the factors affecting the
productivity of employees in an organization is occupational stress.
Another influential factor is quality of work life which is important in
the improvement of work environment conditions and organizational
efficiency. In order to uncover the quality of work life level and to
investigate the impact of occupational stress on quality of work life
among information technology employees in Iran, a cross-sectional
study design was applied and data were gathered using a
questionnaire validated by a group of experts. The results of the study
showed that information technology staffs have average level of both
occupational stress and quality of work life. Furthermore, it was
found that occupational stress has a negative impact on quality of
work life. In addition, the same results were observed for role
ambiguity, role conflict, role under-load, work-pace, work
repetitiveness and tension toward quality of work life. No significant
relation was found between role overload and quality of work life.
Finally, directions for future research are proposed and discussed.
Abstract: In this paper, free vibration analysis of carbon nanotube (CNT) reinforced laminated composite panels is presented. Three types of panels such as flat, concave and convex are considered for study. Numerical simulation is carried out using commercially available finite element analysis software ANSYS. Numerical homogenization is employed to calculate the effective elastic properties of randomly distributed carbon nanotube reinforced composites. To verify the accuracy of the finite element method, comparisons are made with existing results available in the literature for conventional laminated composite panels and good agreements are obtained. The results of the CNT reinforced composite materials are compared with conventional composite materials under different boundary conditions.
Abstract: Chikungunya virus (CHICKV) is an arboviruses belonging to family Tagoviridae and is transmitted to human through by mosquito (Aedes aegypti and Aedes albopictus) bite. A large outbreak of chikungunya has been reported in India between 2006 and 2007, along with several other countries from South-East Asia and for the first time in Europe. It was for the first time that the CHICKV outbreak has been reported with mortality from Reunion Island and increased mortality from Asian countries. CHICKV affects all age groups, and currently there are no specific drugs or vaccine to cure the disease. The need of antiviral agents for the treatment of CHICKV infection and the success of virtual screening against many therapeutically valuable targets led us to carry out the structure based drug design against Chikungunya nSP2 protease (PDB: 3TRK). Highthroughput virtual screening of publicly available databases, ZINC12 and BindingDB, has been carried out using the Openeye tools and Schrodinger LLC software packages. Openeye Filter program has been used to filter the database and the filtered outputs were docked using HTVS protocol implemented in GLIDE package of Schrodinger LLC. The top HITS were further used for enriching the similar molecules from the database through vROCS; a shape based screening protocol implemented in Openeye. The approach adopted has provided different scaffolds as HITS against CHICKV protease. Three scaffolds: Indole, Pyrazole and Sulphone derivatives were selected based on the docking score and synthetic feasibility. Derivatives of Pyrazole were synthesized and submitted for antiviral screening against CHICKV.
Abstract: Today-s healthcare industries had become more
patient-centric than profession-centric, from which the issues of quality of healthcare and the patient safety are the major concerns in the modern healthcare facilities. An unplanned extubation (UE) may
be detrimental to the patient-s life, and thus is one of the major indexes
of patient safety and healthcare quality. A high UE rate not only
defeated the healthcare quality as well as the patient safety policy but
also the nurses- morality, and job satisfaction. The UE problem in a psychiatric hospital is unique and may be a tough challenge for the
healthcare professionals for the patients were mostly lacking communication capabilities. We reported with this essay a particular
project that was organized to reduce the UE rate from the current 2.3%
to a lower and satisfactory level in the long-term care units of a psychiatric hospital. The project was conducted between March 1st,
2011 and August 31st, 2011. Based on the error information gathered
from varied units of the hospital, the team analyzed the root causes
with possible solutions proposed to the meetings. Four solutions were
then concluded with consensus and launched to the units in question.
The UE rate was now reduced to a level of 0.17%. Experience from
this project, the procedure and the tools adopted would be good reference to other hospitals.
Abstract: An effort has been taken to simulate the combustion
and performance characteristics of biodiesel fuel in direct injection
(D.I) low heat rejection (LHR) diesel engine. Comprehensive
analyses on combustion characteristics such as cylinder pressure,
peak cylinder pressure, heat release and performance characteristics
such as specific fuel consumption and brake thermal efficiency are
carried out. Compression ignition (C.I) engine cycle simulation was
developed and modified in to LHR engine for both diesel and
biodiesel fuel. On the basis of first law of thermodynamics the
properties at each degree crank angle was calculated. Preparation and
reaction rate model was used to calculate the instantaneous heat
release rate. A gas-wall heat transfer calculations are based on the
ANNAND-s combined heat transfer model with instantaneous wall
temperature to analyze the effect of coating on heat transfer. The
simulated results are validated by conducting the experiments on the
test engine under identical operating condition on a turbocharged D.I
diesel engine. In this analysis 20% of biodiesel (derived from
Jatropha oil) blended with diesel and used in both conventional and
LHR engine. The simulated combustion and performance
characteristics results are found satisfactory with the experimental
value.
Abstract: Electro-hydraulic power steering (EHPS) system for
the fuel rate reduction and steering feel improvement is comprised of
ECU including the logic which controls the steering system and BL
DC motor and produces the best suited cornering force, BLDC motor,
high pressure pump integrated module and basic oil-hydraulic circuit
of the commercial HPS system.
Electro-hydraulic system can be studied in two ways such as
experimental and computer simulation. To get accurate results in
experimental study of EHPS system, the real boundary management is
necessary which is difficult task. And the accuracy of the experimental
results depends on the preparation of the experimental setup and
accuracy of the data collection. The computer simulation gives
accurate and reliable results if the simulation is carried out considering
proper boundary conditions. So, in this paper, each component of
EHPS was modeled, and the model-based analysis and control logic
was designed by using AMESim
Abstract: The development of wearable sensing technologies is a great challenge which is being addressed by the Proetex FP6 project (www.proetex.org). Its main aim is the development of wearable sensors to improve the safety and efficiency of emergency personnel. This will be achieved by continuous, real-time monitoring of vital signs, posture, activity, and external hazards surrounding emergency workers. We report here the development of carbon dioxide (CO2) sensing boot by incorporating commercially available CO2 sensor with a wireless platform into the boot assembly. Carefully selected commercially available sensors have been tested. Some of the key characteristics of the selected sensors are high selectivity and sensitivity, robustness and the power demand. This paper discusses some of the results of CO2 sensor tests and sensor integration with wireless data transmission
Abstract: The influence of lactulose and inulin on rheological
properties of fermented milk during storage was studied.Pasteurized
milk, freeze-dried starter culture Bb-12 (Bifidobacterium lactis, Chr.
Hansen, Denmark), inulin – RAFTILINE®HP (ORAFI, Belgium) and
syrup of lactulose (Duphalac®, the Netherlands) were used for
experiments. The fermentation process was realized at 37 oC for 16
hours and the storage of products was provided at 4 oC for 7 days.
Measurements were carried out by BROOKFIELD standard methods
and the flow curves were described by Herschel-Bulkley model.
The results of dispersion analysis have shown that both the
concentration of prebiotics (p=0.04
Abstract: Optimum communication and performance in
Wireless Sensor Networks, constitute multi-facet challenges due to
the specific networking characteristics as well as the scarce resource
availability. Furthermore, it is becoming increasingly apparent that
isolated layer based approaches often do not meet the demands posed
by WSNs applications due to omission of critical inter-layer
interactions and dependencies. As a counterpart, cross-layer is
receiving high interest aiming to exploit these interactions and
increase network performance. However, in order to clearly identify
existing dependencies, comprehensive performance studies are
required evaluating the effect of different critical network parameters
on system level performance and behavior.This paper-s main
objective is to address the need for multi-parametric performance
evaluations considering critical network parameters using a well
known network simulator, offering useful and practical conclusions
and guidelines. The results reveal strong dependencies among
considered parameters which can be utilized by and drive future
research efforts, towards designing and implementing highly efficient
protocols and architectures.
Abstract: In this paper a new method is suggested for risk
management by the numerical patterns in data-mining. These patterns
are designed using probability rules in decision trees and are cared to
be valid, novel, useful and understandable. Considering a set of
functions, the system reaches to a good pattern or better objectives.
The patterns are analyzed through the produced matrices and some
results are pointed out. By using the suggested method the direction
of the functionality route in the systems can be controlled and best
planning for special objectives be done.
Abstract: The aim of this study was to establish the feasibility of a minute incremental exercise testing protocol in young asthma children. Twenty-two children with clinically diagnosed mild to moderate asthma volunteered to participate. The maximum incremental exercise test was performed using a cycle ergometer with an electromagnetic braking. A warm-up unloaded for 2 minutes then the workload was started at 40 watts for 2 minutes, and then stepwise increments of 8 watts per 2 minutes were applied. The pedaling frequency was set at 50 rpm. Ventilation and gas exchange were measured with a breath-by-breath automatic metabolic measurement system. Results showed that this test was well tolerated by all asthmatic children. Most of the children reached the VO2 plateau and satisfied the criteria for maximal respiratory exchange ratio of ≥ 1. This Study demonstrated that this testing protocol was suitable for young asthmatic children.
Abstract: In industrial scale of Gas to Liquid (GTL) process in
Fischer-Tropsch (FT) synthesis, a part of reactor outlet gases such as
CO2 and CH4 as side reaction products, is usually recycled. In this
study, the influence of CO2 and CH4 on the performance and
selectivity of Co-Ru/Al2O3 catalyst is investigated by injection of
these gases (0-20 vol. % of feed) to the feed stream. The effect of
temperature and feed flow rate, are also inspected. The results show
that low amounts of CO2 in the feed stream, doesn`t change the
catalyst activity significantly but increasing the amount of CO2 (more
than 10 vol. %) cause the CO conversion to decrease and the
selectivity of heavy components to increase. Methane acts as an inert
gas and doesn`t affect the catalyst performance. Increasing feed flow
rate has negative effect on both CO conversion and heavy component
selectivity. By raising the temperature, CO conversion will increase
but there are more volatile components in the product. The effect of
CO2 on the catalyst deactivation is also investigated carefully and a
mechanism is suggested to explain the negative influence of CO2 on
catalyst deactivation.
Abstract: In sport, human resources management gives special
attention to method of applying volunteers, their maintenance, and
participation of volunteers with each other and management
approaches for better operation of events celebrants. The recognition
of volunteers- characteristics and motives is important to notice,
because it makes the basis of their participation and commitment at
sport environment. The motivation and commitment of 281
volunteers were assessed using the organizational commitment scale,
motivation scale and personal characteristics questionnaire.The
descriptive results showed that; 64% of volunteers were women with
age average 21/24 years old. They were physical education student,
single (71/9%), without occupation (53%) and with average of 5
years sport experience. Their most important motivation was career
factor and the most important commitment factor was normative
factor. The results of examining the hypothesized showed that; age,
sport experience and education are effective in the amount of
volunteers- commitment. And the motive factors such as career,
material, purposive and protective factors also have the power to
predict the amount of sports volunteers- commitment value.
Therefore it is recommended to provide possible opportunities for
volunteers and carrying out appropriate instructional courses by
events executive managers.