Abstract: This study examines analytically the effect of tsunami loads on reinforced concrete (RC) frame buildings. The impact of tsunami wave loads and waterborne objects are analyzed using a typical substandard full-scale two-story RC frame building tested as part of the EU-funded Ecoleader project. The building was subjected to shake table tests in bare condition, and subsequently strengthened using Carbon Fiber Reinforced Polymers (CFRP) composites and retested. Numerical models of the building in both bare and CFRP-strengthened conditions are calibrated in DRAIN-3DX software to match the test results. To investigate the response of wave loads and impact forces, the numerical models are subjected to nonlinear dynamic analyses using force time-history input records. The analytical results are compared in terms of displacements at the floors and at the “impact point” of a boat. The results show that the roof displacement of the CFRP-strengthened building reduced by 63% when compared to the bare building. The results also indicate that strengthening only the mid-height of the impact column using CFRP is more effective at reducing damage when compared to strengthening other parts of the column. Alternative solutions to mitigate damage due to tsunami loads are suggested.
Abstract: The paper deals with the diagnostics of steel roof
structure of the winter sports halls built in 1970 year. The necessity
of the diagnostics has been given by the requirement to the evaluation
design of this structure, which has been caused by the new situation
in the field of the loadings given by the validity of the European
Standards in the Czech Republic from 2010 year. Due to these
changes in the normative rules, in practice existing structures are
gradually subjected to the evaluation design and depending on its
results to the strengthening or reconstruction, respectively. Steel roof
is composed of plane truss main girders, purlins and bracings and the
roof structure is supported by two arch main girders with the span of
L = 84 m. The in situ diagnostics of the roof structure was oriented to
the following parts: (i) determination and evaluation of the actual
material properties of used steel and (ii) verification of the actual
dimensions of the structural members. For the solution the nondestructive
methods have been used for in situ measurement. For the
indicative determination of steel strengths the modified method based
on the determination of Rockwell’s hardness has been used. For the
verification of the member’s dimensions (thickness of hollow
sections) the ultrasound method has been used. This paper presents
the results obtained using these testing methods and their evaluation,
from the viewpoint of the usage for the subsequent static assessment
and design evaluation of the existing structure. For the comparison,
the examples of the similar evaluations realized for steel structures of
the stadiums in Olomouc and Jihlava cities are briefly illustrated, too.
Abstract: Eucalyptus species are well reputed for their
traditional use in Asia as well as in other parts of the world; therefore,
the present study was designed to investigate the antimicrobial and
antioxidant activities associated with essential oils from different
Eucalyptus species. Essential oils from the leaves of six Eucalyptus
species, including: Eucalyptus woodwardi, Eucalyptus stricklandii,
Eucalyptus salubris, Eucalyptus sargentii, Eucalyptus torquata and
Eucalyptus wandoo were separated by hydrodistillation and dried
over anhydrous sodium sulphate. DPPH, ferric reducing antioxidant
power, and hydroxyl radical scavenging activity assays were carried
out to evaluate the antioxidant potential of the oils. The results
indicate that examined oils exhibit substantial antioxidant activities
relative to ascorbic acid. Previously, these oils were evaluated for
their antimicrobial activities, against wide range of bacterial and
fungal strains, and they were shown to possess significant
antimicrobial activities. In this study, further investigation into the
growth kinetics of oil-treated microbial cultures was conducted. The
results clearly demonstrate that the microbial growth was markedly
inhibited when treated with sub-MIC concentrations of the oils.
Taken together, the results obtained indicate a high potential of the
examined essential oils as bioactive oils, for nutraceutical and
medical applications, possessing significant antioxidant and anti
microbial activities.
Abstract: Water flow management is one of the most important
parts of river engineering. Non-uniformity distribution of rainfall and
various flow demand with unreasonable flow management will be
caused destroyed of river ecosystem. Then, it is very serious to
determine ecosystem flow requirement. In this paper, Flow duration
curve indices method which has hydrological based was used to
evaluate environmental flow in Gharasou River, Ardabil, Iran. Using
flow duration curve, Q90 and Q95 for different return periods were
calculated. Their magnitude were determined as 1-day, 3-day, 7-day
and 30 day. According the second method, hydraulic alteration
indices often had low and medium range. In order to maintain river at
an acceptable ecological condition, minimum daily discharge of
index Q95 is 0.7 m3.s-1.
Abstract: Assembly line balancing problem is aimed to divide
the tasks among the stations in assembly lines and optimize some
objectives. In assembly lines the workload on stations is different
from each other due to different tasks times and the difference in
workloads between stations can cause blockage or starvation in some
stations in assembly lines. Buffers are used to store the semi-finished
parts between the stations and can help to smooth the assembly
production. The assembly line balancing and buffer sizing problem
can affect the throughput of the assembly lines. Assembly line
balancing and buffer sizing problems have been studied separately in
literature and due to their collective contribution in throughput rate of
assembly lines, balancing and buffer sizing problem are desired to
study simultaneously and therefore they are considered concurrently
in current research. Current research is aimed to maximize
throughput, minimize total size of buffers in assembly line and
minimize workload variations in assembly line simultaneously. A
multi objective optimization objective is designed which can give
better Pareto solutions from the Pareto front and a simple example
problem is solved for assembly line balancing and buffer sizing
simultaneously. Current research is significant for assembly line
balancing research and it can be significant to introduce optimization
approaches which can optimize current multi objective problem in
future.
Abstract: Spam is any unwanted electronic message or material
in any form posted too many people. As the world is growing as
global world, social networking sites play an important role in
making world global providing people from different parts of the
world a platform to meet and express their views. Among different
social networking sites Facebook become the leading one. With
increase in usage different users start abusive use of Facebook by
posting or creating ways to post spam. This paper highlights the
potential spam types nowadays Facebook users’ faces. This paper
also provide the reason how user become victim to spam attack. A
methodology is proposed in the end discusses how to handle different
types of spam.
Abstract: Environmental impacts of six 3D printers using
various materials were compared to determine if material choice
drove sustainability, or if other factors such as machine type, machine
size, or machine utilization dominate. Cradle-to-grave life-cycle
assessments were performed, comparing a commercial-scale FDM
machine printing in ABS plastic, a desktop FDM machine printing in
ABS, a desktop FDM machine printing in PET and PLA plastics, a
polyjet machine printing in its proprietary polymer, an SLA machine
printing in its polymer, and an inkjet machine hacked to print in salt
and dextrose. All scenarios were scored using ReCiPe Endpoint H
methodology to combine multiple impact categories, comparing
environmental impacts per part made for several scenarios per
machine. Results showed that most printers’ ecological impacts were
dominated by electricity use, not materials, and the changes in
electricity use due to different plastics was not significant compared
to variation from one machine to another. Variation in machine idle
time determined impacts per part most strongly. However, material
impacts were quite important for the inkjet printer hacked to print in
salt: In its optimal scenario, it had up to 1/38th the impacts coreper
part as the worst-performing machine in the same scenario. If salt
parts were infused with epoxy to make them more physically robust,
then much of this advantage disappeared, and material impacts
actually dominated or equaled electricity use. Future studies should
also measure DMLS and SLS processes / materials.
Abstract: Due to water shortage, application of saline water for
irrigation is an urgent in agriculture. In this study the effect of
calcium and potassium application as additive in saline root media for
reduce salinity adverse effects was investigated on tomato growth in
a hydroponic system with unequal distribution of salts in the root
media, which was divided in to two equal parts containing full
Johnson nutrient solution and 40 mMNaCl solution, alone or in
combination with KCl (6 mM), CaCl2 (4 mM), K+Ca (3+2 mM) or
half-strength Johnson nutrient solution. The root splits were
exchanged every 7 days. Results showed that addition of calcium,
calcium-potassium and nutrition elements equivalent to half the
concentration of Johnson formula to the saline-half of culture media
minimized the reduction in plant growth caused by NaCl, although
addition of potassium to culture media wasn’t effective. The greatest
concentration of sodium was observed at the shoot of treatments
which had smallest growth. According to the results of this study, in
case of dynamic and non-uniform distribution of salts in the root
media, by addition of additive to the saline solution, it would be
possible to use of saline water with no significant growth reduction.
Abstract: Developing young people’s employability is a key
policy issue for ensuring their successful transition to the labour
market and their access to career oriented employment. The youths of
today irrespective of their gender need to acquire the knowledge,
skills and attitudes that will enable them to create or find jobs as well
as cope with unpredictable labour market changes throughout their
working lives. In a study carried out to determine the influence of
gender on job-competencies requirements of chemical-based
industries and undergraduate-competencies acquisition by chemists
working in the industries, all chemistry graduates working in twenty
(20) chemical-based industries that were randomly selected from six
sectors of chemical-based industries in Lagos and Ogun States of
Nigeria were administered with Job-competencies required and
undergraduate-competencies acquired assessment questionnaire. The
data were analysed using means and independent sample t-test. The
findings revealed that the population of female chemists working in
chemical-based industries is low compared with the number of male
chemists; furthermore, job-competencies requirements are found not
to be gender biased while there is no significant difference in
undergraduate-competencies acquisition of male and female
chemists. This suggests that females should be given the same
opportunity of employment in chemical-based industries as their male
counterparts. The study also revealed the level of acquisition of
undergraduate competencies as related to the needs of chemicalbased
industries.
Abstract: Over the last few decades, oilfield service rolling
equipment has significantly increased in weight, primarily because of
emissions regulations, which require larger/heavier engines, larger
cooling systems, and emissions after-treatment systems, in some
cases, etc. Larger engines cause more vibration and shock loads,
leading to failure of electronics and control systems.
If the vibrating frequency of the engine matches the system
frequency, high resonance is observed on structural parts and mounts.
One such existing automated control equipment system comprising
wire rope mounts used for mounting computers was designed
approximately 12 years ago. This includes the use of an industrialgrade
computer to control the system operation. The original
computer had a smaller, lighter enclosure. After a few years, a newer
computer version was introduced, which was 10 lbm heavier. Some
failures of internal computer parts have been documented for cases in
which the old mounts were used. Because of the added weight, there
is a possibility of having the two brackets impact each other under
off-road conditions, which causes a high shock input to the computer
parts. This added failure mode requires validating the existing mount
design to suit the new heavy-weight computer.
This paper discusses the modal finite element method (FEM)
analysis and experimental modal analysis conducted to study the
effects of vibration on the wire rope mounts and the computer. The
existing mount was modelled in ANSYS software, and resultant
mode shapes and frequencies were obtained. The experimental modal
analysis was conducted, and actual frequency responses were
observed and recorded.
Results clearly revealed that at resonance frequency, the brackets
were colliding and potentially causing damage to computer parts. To
solve this issue, spring mounts of different stiffness were modeled in
ANSYS software, and the resonant frequency was determined.
Increasing the stiffness of the system increased the resonant
frequency zone away from the frequency window at which the engine
showed heavy vibrations or resonance. After multiple iterations in
ANSYS software, the stiffness of the spring mount was finalized,
which was again experimentally validated.
Abstract: Machining parameters are very important in
determining the surface quality of any material. In the past decade,
some new engineering materials were developed for the
manufacturing industry which created a need to conduct an
investigation on the impact of the said parameters on their surface
roughness. Polyurethane (PU) block is widely used in the automotive
industry to manufacture parts such as checking fixtures that are used
to verify the dimensional accuracy of automotive parts. In this paper,
the design of experiment (DOE) was used to investigate on the effect
of the milling parameters on the PU block. Furthermore, an analysis
of the machined surface chemical composition was done using
scanning electron microscope (SEM). It was found that the surface
roughness of the PU block is severely affected when PU undergoes a
flood machining process instead of a dry condition. In addition the
stepover and the silicon content were found to be the most significant
parameters that influence the surface quality of the PU block.
Abstract: Monocopter is a single-wing rotary flying vehicle
which has the capability of hovering. This flying vehicle includes two
dynamic parts in which more efficiency can be expected rather than
other Micro UAVs due to the extended area of wing compared to its
fuselage. Low cost and simple mechanism in comparison to other
vehicles such as helicopter are the most important specifications of
this flying vehicle.
In the previous paper we discussed the introduction of the final
system but in this paper, the experimental design process of
Monocopter and its control algorithm has been investigated in
general. Also the editorial bugs in the previous article have been
corrected and some translational ambiguities have been resolved.
Initially by constructing several prototypes and carrying out many
flight tests the main design parameters of this air vehicle were
obtained by experimental measurements. Eventually the required
main monocopter for this project was constructed. After construction
of the monocopter in order to design, implementation and testing of
control algorithms first a simple optic system used for determining
the heading angle. After doing numerous tests on Test Stand, the
control algorithm designed and timing of applying control inputs
adjusted. Then other control parameters of system were tuned in
flight tests. Eventually the final control system designed and
implemented using the AHRS sensor and the final operational tests
performed successfully.
Abstract: Using cold EGR method with variable venturi and
turbocharger has a very significant effect on reduction of NOX and
grime simultaneously. EGR cooler is one of the most important parts
in the cold EGR circuit. In this paper optimum design of cooler for
working in different percentages of EGR and for determining
optimum temperature of exhausted gases, growth of efficiency,
reduction of weight, dimension, expenditures, sediment and also
optimum performance by using gasoil which has significant amounts
of brimstone are investigated and optimized.
Abstract: Forging parts is used to automobiles; because, they have high strength and it is possible to press them into complicated shape. When itis possible to manufacture hollow forging parts, it leads to reduce weightof the automobiles. But, hollow forging parts are confined to axisymmetrical shape. Hollowforging parts that were pressed to complicated shape are expected. Therefore, we forge a blank that aluminum alloy was inserted in stainless steel. After that, we can providecomplex forging parts that are reduced weight,ifit is possible to be melted the aluminum alloy away by using different of melting points.It is necessary to establish heat forging analysis methodon blank consist of stainless steel and aluminum alloy. Because,this forging is different from conventional forging and this technology is not confirmed. In this study, we compared forging experiment with numerical analysis on the view point of forming load and shape after forming and establish how to set the material temperaturesof two metals and material property of stainless steel on the analysis method. Consequently, temperature difference of stainless steel and aluminum alloy was obtained by experiment. We got material property of stainless steel on forging experimental by compression tests. We had compared numerical analysis that was used the temperature difference of two metals and the material property of stainless steel on forging experimental with forging experiment. Forging analysis method on blankconsist of two metals was established by result of numerical analysis having agreedwith result of forging experiment.
Abstract: In sheet metal forming process, raw material
mechanical properties are important parameters. This paper is to
compare the wall’s incline angle or formability of SS 400 steel and
SUS 304 stainless steel in single point incremental forming. The two
materials are ferrous base alloyed, which have the different unit cell,
mechanical property and chemical composition. They were forming
into cone shape specimens having 100 mm diameter with different
wall’s incline angle: 90o, 75o and 60o. The investigation was
continued until the specimens formed surface facture. The
experimental result showed that the smaller the wall incline angle
higher the formability with the both materials. The formability limit
of the ferrous base alloy was approx. 60o wall’s incline angle. By
nature, SS 400 has higher formability than SUS 304. This result can
be used as the initial data in designing the single point incremental
forming parts.
Abstract: Powder metallurgy (P/M) is the only economic way to
produce porous parts/products. P/M can produce near net shape parts
hence reduces wastage of raw material and energy, avoids various
machining operations. The most vital use of P/M is in production of
metallic filters and self lubricating bush bearings and siding surfaces.
The porosity of the part can be controlled by varying compaction
pressure, sintering temperature and composition of metal powder
mix. The present work is aimed for experimental analysis of friction
and wear properties of self lubricating copper and tin bush bearing.
Experimental results confirm that wear rate of sintered component
is lesser for components having 10% tin by weight percentage. Wear
rate increases for high tin percentage (experimented for 20% tin and
30% tin) at same sintering temperature. Experimental results also
confirms that wear rate of sintered component is also dependent on
sintering temperature, soaking period, composition of the preform,
compacting pressure, powder particle shape and size.
Interfacial friction between die and punch, between inter powder
particles, between die face and powder particle depends on
compaction pressure, powder particle size and shape, size and shape
of component which decides size & shape of die & punch, material of
die & punch and material of powder particles.
Abstract: The purpose of this work is examining the multiproduct
multi-stage in a battery production line. To improve the
performances of an assembly production line by determine the
efficiency of each workstation. Data collected from every
workstation. The data are throughput rate, number of operator, and
number of parts that arrive and leaves during part processing. Data
for the number of parts that arrives and leaves are collected at least at
the amount of ten samples to make the data is possible to be analyzed
by Chi-Squared Goodness Test and queuing theory. Measures of this
model served as the comparison with the standard data available in
the company. Validation of the task time value resulted by comparing
it with the task time value based on the company database. Some
performance factors for the multi-product multi-stage in a battery
production line in this work are shown.
The efficiency in each workstation was also shown. Total
production time to produce each part can be determined by adding
the total task time in each workstation. To reduce the queuing time
and increase the efficiency based on the analysis any probably
improvement should be done. One probably action is by increasing
the number of operators how manually operate this workstation.
Abstract: This paper contains 2 main parts. In the first part of paper we simulated and studied three types of electrode patterns used in various industries for suspension and handling of the semiconductor and glass and we selected the best pattern by evaluating the electrostatic force, which was comb pattern electrode.
In the second part we investigated the parameters affecting the amount of electrostatic force such as the gap between surface and electrode (g), the electrode width (w), the gap between electrodes (t), the surface permittivity and electrode length and methods of improvement of adhesion force by changing these values.
Abstract: South Africa has some regions which are susceptible
to moderate seismic activity. A peak ground acceleration of between
0.1g and 0.15g can be expected in the southern parts of the Western
Cape. Unreinforced Masonry (URM) is commonly used as a
construction material for 2 to 5 storey buildings in underprivileged
areas in and around Cape Town. URM is typically regarded as the
material most vulnerable to damage when subjected to earthquake
excitation. In this study, a three-storey URM building was analysed
by applying seven earthquake time-histories, which can be expected
to occur in South Africa using a finite element approach.
Experimental data was used to calibrate the in- and out-of-plane
stiffness of the URM. The results indicated that tensile cracking of
the in-plane piers was the dominant failure mode. It is concluded that
URM buildings of this type are at risk of failure especially if
sufficient ductility is not provided. The results also showed that
connection failure must be investigated further.
Abstract: One of the most important tasks in the risk
management is the correct determination of probability of default
(PD) of particular financial subjects. In this paper a possibility of
determination of financial institution’s PD according to the creditscoring
models is discussed. The paper is divided into the two parts.
The first part is devoted to the estimation of the three different
models (based on the linear discriminant analysis, logit regression
and probit regression) from the sample of almost three hundred US
commercial banks. Afterwards these models are compared and
verified on the control sample with the view to choose the best one.
The second part of the paper is aimed at the application of the chosen
model on the portfolio of three key Czech banks to estimate their
present financial stability. However, it is not less important to be able
to estimate the evolution of PD in the future. For this reason, the
second task in this paper is to estimate the probability distribution of
the future PD for the Czech banks. So, there are sampled randomly
the values of particular indicators and estimated the PDs’ distribution,
while it’s assumed that the indicators are distributed according to the
multidimensional subordinated Lévy model (Variance Gamma model
and Normal Inverse Gaussian model, particularly). Although the
obtained results show that all banks are relatively healthy, there is
still high chance that “a financial crisis” will occur, at least in terms
of probability. This is indicated by estimation of the various quantiles
in the estimated distributions. Finally, it should be noted that the
applicability of the estimated model (with respect to the used data) is
limited to the recessionary phase of the financial market.