Abstract: We used high-precision Global Positioning System
(GPS) to geodetically constrain the motion of stations in the
Darjiling-Sikkim Himalayan (DSH) wedge and examine the
deformation at the Indian-Tibetan plate boundary using IGS
(International GPS Service) fiducial stations. High-precision GPS
based displacement and velocity field was measured in the DSH
between 1997 and 2009. To obtain additional insight north of the
Indo-Tibetan border and in the Darjiling-Sikkim-Tibet (DaSiT)
wedge, published velocities from four stations J037, XIGA, J029 and
YADO were also included in the analysis. India-fixed velocities or
the back-slip was computed relative to the pole of rotation of the
Indian Plate (Latitude 52.97 ± 0.22º, Longitude - 0.30 ± 3.76º, and
Angular Velocity 0.500 ± 0.008º/ Myr) in the DaSiT wedge.
Dislocation modelling was carried out with the back-slip to model the
best possible solution of a finite rectangular dislocation or the
causative fault based on dislocation theory that produced the
observed back-slip using a forward modelling approach. To find the
best possible solution, three different models were attempted. First,
slip along a single thrust fault, then two thrust faults and in finally,
three thrust faults were modelled to simulate the back-slip in the
DaSiT wedge. The three-fault case bests the measured displacements
and is taken as the best possible solution.
Abstract: Fibrin degradation is an important part in prevention
or treatment of intravascular thrombosis and cardiovascular diseases.
Plasmin like fibrinolytic enzymes has given new hope to patient with
cardiovascular diseases by treating fibrin aggregation related diseases
with traditional plasminogen activator which have many side effects.
Various researches involving wide range of sources for production of
fibrinolytic proteases, from bacteria, fungi, insects and fermented
foods. But few have looked into endophytic fungi as a potential
source. Sixteen (16) endophytic fungi were isolated from Hibiscus sp.
leaves from six different locations in Shah Alam, Selangor. Only two
endophytic fungi, FH3 and S13 showed positive fibrinolytic protease
activities. FH3 produced 5.78cm and S13 produced 4.48cm on Skim
Milk Agar after 4 days of incubation at 27°C. Fibrinolytic activity
was observed; 3.87cm and 1.82cm diameter clear zone on fibrin plate
of FH3 and S13 respectively. 18srRNA was done for identification of
the isolated fungi with positive fibrinolytic protease. S13 had the
highest similarity (100%) to that of Penicillium citrinum strain TG2
and FH3 had the highest similarity (99%) to that of Fusarium sp.
FW2PhC1, Fusarium sp. 13002, Fusarium sp. 08006, Fusarium
equiseti strain Salicorn 8 and Fungal sp. FCASAn-2. Media
composition variation showed the effects of carbon nitrogen on
protein concentration, where the decrement of 50% of media
composition caused drastic decrease in protease of FH3 from 1.081 to
0.056 and also S13 from 2.946 to 0.198.
Abstract: The mixed convection stagnation point flow toward a vertical plate is investigated. The external flow impinges normal to the heated plate and the surface temperature is assumed to vary linearly with the distance from the stagnation point. The governing partial differential equations are transformed into a set of ordinary differential equations, which are then solved numerically using MATLAB routine boundary value problem solver bvp4c. Numerical results show that dual solutions are possible for a certain range of the mixed convection parameter. A stability analysis is performed to determine which solution is linearly stable and physically realizable.
Abstract: The effect of non-homogeneity on the free transverse vibration of thin rectangular plates of bilinearly varying thickness has been analyzed using generalized differential quadrature (GDQ) method. The non-homogeneity of the plate material is assumed to arise due to linear variations in Young’s modulus and density of the plate material with the in-plane coordinates x and y. Numerical results have been computed for fully clamped and fully simply supported boundary conditions. The solution procedure by means of GDQ method has been implemented in a MATLAB code. The effect of various plate parameters has been investigated for the first three modes of vibration. A comparison of results with those available in literature has been presented.
Abstract: The paper gives basic information on application of
rotation bending for manufacturing ship hull parts from steel plates
and on MGPS machines, employed for this purpose.
Abstract: In recent years many finite elements have been
developed for plate bending analysis. The formulated elements are
based on the strain based approach. This approach leads to the
representation of the displacements by higher order polynomial terms
without the need for the introduction of additional internal and
unnecessary degrees of freedom. Good convergence can also be
obtained when the results are compared with those obtained from the
corresponding displacement based elements, having the same total
number of degrees of freedom. Furthermore, the plate bending
elements are free from any shear locking since they converge to the
Kirchhoff solution for thin plates contrarily for the corresponding
displacement based elements. In this paper the efficiency of the strain
based approach compared to well known displacement formulation is
presented. The results obtained by a new formulated plate bending
element based on the strain approach and Kirchhoff theory are
compared with some others elements. The good convergence of the
new formulated element is confirmed.
Abstract: This study applies the inverse method and three- dimensional CFD commercial software in conjunction with the experimental temperature data to investigate the heat transfer and fluid flow characteristics of the plate-fin heat sink in a closed rectangular enclosure for various values of fin height. The inverse method with the finite difference method and the experimental temperature data is applied to determine the heat transfer coefficient. The k-ε turbulence model is used to obtain the heat transfer and fluid flow characteristics within the fins. To validate the accuracy of the results obtained, the comparison of the average heat transfer coefficient is made. The calculated temperature at selected measurement locations on the plate-fin is also compared with experimental data.
Abstract: Effects of insertion of coiled wire in juxtaposition with twisted tapes on heat transfer rate and solar radiation without disturbing the flow inside the riser tubes in a solar flat plate collector is experimentally reconnoitered in this present work. The wire coil used as a turbulator is placed inside the riser tube while the twisted tape is inserted into the wire coil to create a continuous swirling flow along the tube wall. The results of the heat transfer have been compared well with the available results. The heat transfer rate in the collector has been found to be increased by 18% to 70%. Solar water heaters having inserts in the flow tubes perform better than the conventional plain ones. It has been observed that heat losses are reduced consequently increasing the thermal performance about 30% over the plain water heaters under the same operating conditions. The effect of twisted tape with wire coils, flow Reynolds number, and the intensity of solar radiation on the thermal performance of the solar water heater has been presented. Effects of insertion of coiled wire in juxtaposition with twisted tapes on heat transfer rate and solar radiation without disturbing the flow inside the riser tubes in a solar flat plate collector is experimentally reconnoitered in this present work. The wire coil used as a turbulator is placed inside the riser tube while the twisted tape is inserted into the wire coil to create a continuous swirling flow along the tube wall. The results of the heat transfer have been compared well with the available results. The heat transfer rate in the collector has been found to be increased by 18% to 70%. Solar water heaters having inserts in the flow tubes perform better than the conventional plain ones. It has been observed that heat losses are reduced consequently increasing the thermal performance about 30% over the plain water heaters under the same operating conditions. The effect of twisted tape with wire coils, flow Reynolds number, and the intensity of solar radiation on the thermal performance of the solar water heater has been presented.
Abstract: This study compared the mechanical and microstructural properties produced during friction stir welding (FSW) of S275 structural steel in air and underwater. Post weld tests assessed the tensile strength, micro-hardness, distortion, Charpy impact toughness and fatigue performance in each case. The study showed that there was no significant difference in the strength, hardness or fatigue life of the air and underwater specimens. However, Charpy impact toughness was shown to decrease for the underwater specimens and was attributed to a lower degree of recrystallization caused by the higher rate of heat loss experienced when welding underwater. Reduced angular and longitudinal distortion was observed in the underwater welded plate compared to the plate welded in air.
Abstract: This paper presents the effect of electric field
distribution which is an electric field intensity analysis. Consideration
of the dielectric heating of grains and insects, the rice and rice
weevils are utilized for dielectric heating analysis. Furthermore, this
analysis compares the effect of electric field distribution in rice and
rice weevil. In this simulation, two copper plates are used to generate
the electric field for dielectric heating system and put the rice
materials between the copper plates. The simulation is classified in
two cases, which are case I one rice weevil is placed in the rice and
case II two rice weevils are placed at different position in the rice.
Moreover, the probes are located in various different positions on
plate. The power feeding on this plate is optimized by using CST EM
studio program of 1000 watt electrical power at 39 MHz resonance
frequency. The results of two cases are indicated that the most
electric field distribution and intensity are occurred on the rice and
rice weevils at the near point of the probes. Moreover, the heat is
directed to the rice weevils more than the rice. When the temperature
of rice and rice weevils are calculated and compared, the rice weevils
has the temperature more than rice is about 41.62 Celsius degrees.
These results can be applied for the dielectric heating applications to
eliminate insect.
Abstract: The aim of the current research was to determine
quality parameters changes of dried venison during storage. Protein,
fat and moisture content dynamics as well microbiological quality
was analyzed. For the experiments the meat (0.02×4.00×7.00 cm)
pieces were marinated in “teriyaki sauce” marinade (composition:
teriyaki sauce, sweet and sour sauce, taco sauce, soy sauce, American
BBQ sauce hickory, sesame oil, garlic, garlic salt, tabasco red pepper
sauce) at 4±2°C temperature for 48±1h. Sodium monophosphate
(E339) was also added in part of marinade to improve the meat
textural properties. After marinating, meat samples were dried in
microwave-vacuum drier MUSSON–1, packaged in vacuum pouches
made from polymer film (PA/PE) with barrier properties and storage
for 4 months at 18±1°C temperature in dark place. Dried venison
samples were analyzed after 0, 35, 91 and 112 days of storage.
During the storage total plate counts of dried venison samples
significantly (p
Abstract: This research studies the electroplating of zinc coating
in the zinc chloride bath mixed with supercritical CO2. The sodium
fluoride (NaF) was used as the bath additive to change the structure
and property of the coating, and therefore the roughness and corrosion
resistance of the zinc coating was investigated. The surface
characterization was performed using optical microscope (OM), X-ray
diffractometer (XRD), and α-step profilometer. Moreover, the
potentiodynamic polarization measurement in 3% NaCl solution was
employed in the corrosion resistance evaluation. Because of the
emulsification of the electrolyte mixed in Sc-CO2, the electroplated
zinc produced the coating with smoother surface, smaller grain, better
throwing power and higher corrosion resistance. The main role played
by the NaF was to reduce the coating’s roughness and grain size. In
other words, the CO2 mixed with the electrolyte under the supercritical
condition performed the similar function as brighter and leveler in zinc
electroplating to enhance the throwing power and corrosion resistance
of the coating.
Abstract: A mechanically-resonant torsional spring scanner was developed in a recent study. Various methods were developed to improve the angular displacement of the scanner while maintaining the scanner frequency. However the effects of rotor magnet radial position on scanner characteristics were not well investigated. In this study, the relationships between the magnet position and the scanner characteristics such as natural frequency, angular displacement and stress level were studied. A finite element model was created and an average deviation of 3.18% was found between the simulation and experimental results, qualifying the simulation results as a guide for further investigations. Three magnet positions on the transverse oscillating suspended plate were investigated by finite element analysis (FEA) and one of the positions were selected as the design position. The magnet position with the longest distance from the twist axis of mirror was selected since it attains minimum stress level, while exceeding the minimum critical flicker frequency and delivering the targeted angular displacement to the scanner.
Abstract: In this paper, we have investigated the free convection MHD flow due to heat and mass transfer through porous medium bounded by an infinite vertical non-conducting porous plate with time dependent suction under the influence of uniform transverse magnetic field of strength H0. When Temperature (T) and Concentration (C) at the plate is oscillatory with time about a constant non-zero mean. The velocity distribution, the temperature distribution, co-efficient of skin friction and role of heat transfer is investigated. Here the partial differential equations are involved. Exact solution is not possible so approximate solution is obtained and various graphs are plotted.
Abstract: This paper describes an identification of specific shapes within binary images using the morphological Hit-or-Miss Transform (HMT). Hit-or-Miss transform is a general binary morphological operation that can be used in searching of particular patterns of foreground and background pixels in an image. It is actually a basic operation of binary morphology since almost all other binary morphological operators are derived from it. The input of this method is a binary image and a structuring element (a template which will be searched in a binary image) while the output is another binary image. In this paper a modification of Hit-or-Miss transform has been proposed. The accuracy of algorithm is adjusted according to the similarity of the template and the sought template. The implementation of this method has been done by C language. The algorithm has been tested on several images and the results have shown that this new method can be used for similar shape detection.
Abstract: This paper is an attempt to describe some of the results that had been found through a journey of study in the field of particle physics. This study consists of two parts, one about the measurement of the cross section of the decay of the Z particle in two electrons, and the other deals with the measurement of the cross section of the multi-photon absorption process using a beam of Laser in the Liquid Argon Time Projection Chamber.
The first part of the paper concerns the results based on the analysis of a data sample containing 8120 ee candidates to reconstruct the mass of the Z particle for each event where each event has an ee pair with PT(e) > 20GeV, and η(e) < 2.5. Monte Carlo templates of the reconstructed Z particle were produced as a function of the Z mass scale. The distribution of the reconstructed Z mass in the data was compared to the Monte Carlo templates, where the total cross section is calculated to be equal to 1432pb.
The second part concerns the Liquid Argon Time Projection Chamber, LAr TPC, the results of the interaction of the UV Laser, Nd-YAG with λ= 266mm, with LAr and through the study of the multi-photon ionization process as a part of the R&D at Bern University. The main result of this study was the cross section of the process of the multi-photon ionization process of the LAr, σe = 1.24±0.10stat±0.30sys.10 -56cm4.
Abstract: The effect of mass transfer on MHD mixed convective flow along inclined porous plate with thermodiffusion have been analyzed on the basis of boundary layer approximations. The fluid is assumed to be incompressible and dense, and a uniform magnetic field is applied normal to the direction of the flow. A Similarity transformation is used to transform the problem under consideration into coupled nonlinear boundary layer equations which are then solved numerically using the Runge-Kutta sixth-order integration scheme together with Nachtsheim-Swigert shooting iteration technique. The behavior of velocity, temperature, concentration, local skin-friction, local Nusselt number and local Sherwood number for different values of parameters have been computed and the results are presented graphically, and analyzed thereafter. The validity of the numerical methodology and the results are questioned by comparing the findings obtained for some specific cases with those available in the literature, and a comparatively good agreement is reached.
Abstract: Iran Central Plateau encompasses a large proportion of this country. The weather in these flat plains is warm and arid with very little precipitation. Different attempts in architecture have been done to alleviate the weather severity of this area and create a living place compatible with humans’ comfort criteria. Investigations have showed that some of the most successful approaches in traditional architecture of the area has been forgotten or are not being used widely. As sustainability is defined as an appropriate solution for environmental, economical, and social disorders, this research is a try to demonstrate the sustainability in aforementioned architecture and based on these studies, propounds solutions for today architecture in hot arid zones.
Abstract: The problem of magnetohydrodynamics boundary layer flow and heat transfer on a permeable stretching surface in a second grade nanofluid under the effect of heat generation and partial slip is studied theoretically. The Brownian motion and thermophoresis effects are also considered. The boundary layer equations governed by the PDE’s are transformed into a set of ODE’s with the help of local similarity transformations. The differential equations are solved by variational finite element method. The effects of different controlling parameters on the flow field and heat transfer characteristics are examined. The numerical results for the dimensionless velocity, temperature and nanoparticle volume fraction as well as the reduced Nusselt and Sherwood number have been presented graphically. The comparison confirmed excellent agreement. The present study is of great interest in coating and suspensions, cooling of metallic plate, oils and grease, paper production, coal water or coal-oil slurries, heat exchangers technology, materials processing exploiting.
Abstract: There are many researches on parameters affecting seismic behavior of steel moment frames. Great deal of these researches considers cover plate connections with or without haunch and direct beam to column connection for exterior columns. Also there are experimental results for interior connections with equal beam depth on both sides but not much research has been performed on the seismic behavior of joints with unequal beam depth. Based on previous experimental results, a series of companion analyses have been set up considering different beam height and connection detailing configuration to investigate the seismic behavior of the connections. Results of this study indicate that when the differences between beams height on both side increases, use of haunch connection system leads to significant improvement in the seismic response whereas other configurations did not provide satisfying results.