Abstract: This work evaluates the ability of OBT for detecting parametric faults in continuous-time filters. To this end, we adopt two filters with quite different topologies as cases of study and a previously reported statistical fault model. In addition, we explore the behavior of the test schemes when a particular test condition is changed. The new data reported here, obtained from a fault simulation process, reveal a lower performance of OBT not observed in previous work using single-deviation faults, even under the change in the test condition.
Abstract: Construction and Demolition (C&D) wastes contribute the highest percentage of wastes worldwide (75%). Furthermore, ceramic materials contribute the highest percentage of wastes within the C&D wastes (54%). The current option for disposal of ceramic wastes is landfill. This is due to unavailability of standards, avoidance of risk, lack of knowledge and experience in using ceramic wastes in construction. The ability of ceramic wastes to act as a pozzolanic material in the production of cement has been effectively explored. The results proved that temperatures used in the manufacturing of these tiles (about 900⁰C) are sufficient to activate pozzolanic properties of clay. They also showed that, after optimization (11-14% substitution); the cement blend performs better, with no morphological difference between the cement blended with ceramic waste, and that blended with other pozzolanic materials. Sanitary ware and electrical insulator porcelain wastes are some wastes investigated for usage as aggregates in concrete production. When optimized, both produced good results, better than when natural aggregates are used. However, the research on ceramic wastes as partial substitute for fine aggregates or cement has not been overly exploited as the other areas. This review has been concluded with focus on investigating whether ceramic wall tile wastes used as partial substitute for cement and fine aggregates could prove to be beneficial since the two materials are the most high-priced during concrete production.
Abstract: The basic ability of a vehicle is to “run”, “turn” and “stop”. The safeness and comfort during a drive on various road surfaces and speed depends on the performance of these basic abilities of the vehicle. Stability and maneuverability of a vehicle are vital in automotive engineering. The stability of a vehicle is the ability of the vehicle to revert back to a stable state during a drive when faced with crosswinds and irregular road conditions. Maneuverability of a vehicle is the ability of the vehicle to change direction during a drive swiftly based on the steering of the driver. The stability and maneuverability of a vehicle can also be defined as the driving stability of the vehicle. Since the fossil fueled vehicle is the main type of transportation today, the environmental factor in automotive engineering is also vital. By improving the fuel efficiency of the vehicle, the overall carbon emission will be reduced, thus reducing the effect of global warming and greenhouse gas on the Earth. Another main focus of the automotive engineering is the safety performance of the vehicle, especially with the worrying increase of vehicle collision every day. With better safety performance of a vehicle, every driver will be more confident driving every day. Next, let us focus on the “turn” ability of a vehicle. By improving this particular ability of the vehicle, the cornering limit of the vehicle can be improved, thus increasing the stability and maneuverability factor. In order to improve the cornering limit of the vehicle, a study to find the balance between the steering systems, the stability of the vehicle, higher lateral acceleration and the cornering limit detection must be conducted. The aim of this research is to study and develop a new suspension system that will boost the lateral acceleration of the vehicle and ultimately improving the cornering limit of the vehicle. This research will also study environmental factor and the stability factor of the new suspension system. The double wishbone suspension system is widely used in a four-wheel vehicle, especially for high cornering performance sports car and racing car. The double wishbone designs allow the engineer to carefully control the motion of the wheel by controlling such parameters as camber angle, caster angle, toe pattern, roll center height, scrub radius, scuff, and more. The development of the new suspension system will focus on the ability of the new suspension system to optimize the camber control and to improve the camber limit during a cornering motion. The research will be carried out using the CAE analysis tool. Using this analysis tool we will develop a JSAE Formula Machine equipped with the double wishbone system and also the new suspension system and conduct simulation and conduct studies on the performance of both suspension systems.
Abstract: The Deposit Guarantee Fund (DGF) and its communication with the Society, in general, and with the deposit client of Financial Institutions, in particular, is discussed through the challenges of the accounting and financial report. The Bank of Portugal promotes the Portuguese Deposit Guarantee Fund (PDGF) as a financial institution that enhanced the market confidence and stability on the deposit-insurance system. Due to the nature of their functions, it must be subject to regulation and supervision that provides a first line of defense against adversely affect confidence on the Portuguese financial market. First, this research provides evidence of the effectiveness of the protection mechanisms on the deposit insurance system, which provides high and equal protection to all stakeholders. Second, it emphasizes the need of requirements of rigorous accounting process and effective financial report to reduce the moral hazard implications. Third, this research focuses on the need of total disclosure of the financial information which gives higher transparency and protection to deposit client of financial institutions.
Abstract: The article focuses on the role of FDI in Georgia’s economic development for the last decade. To attract as much FDI as possible a proper investment climate should be on the place - institutional, policy and regulatory environment. Well developed investment climate is the chance and motivation for both, local economy and foreign companies, to generate maximum income, create new work places and improve the quality of life. FDI trend is one of the best indicators of country’s economic sustainability and its attractiveness. Especially for small and developing countries, the amount of FDI matters, therefore most of such countries are trying to compete with each other through improving their investment climate according to different world famous indexes. As a result of impressive reforms since 2003, Georgian economy was benefited with large invasion of FDI, however the level of per capita GDP is still law in comparison to Eastern European countries and it should be improved. The main idea of the paper is to show a real linkage between FDI and employment ration, on the case of Georgian economy.
Abstract: With short production development times, there is an increased need to demonstrate product reliability relatively quickly with minimal testing. In such cases there may be few if any observed failures. Thus it may be difficult to assess reliability using the traditional reliability test plans that measure only time (or cycles) to failure. For many components, degradation measures will contain important information about performance and reliability. These measures can be used to design a minimal test plan, in terms of number of units placed on test and duration of the test, necessary to demonstrate a reliability goal. In this work we present a case study involving an electronic component subject to degradation. The data, consisting of 42 degradation paths of cycles to failure, are first used to estimate a reliability function. Bootstrapping techniques are then used to perform power studies and develop a minimal reliability test plan for future production of this component.
Abstract: In a deregulated power system structure, power producers and customers share a common transmission network for wheeling power from the point of generation to the point of consumption. All parties in this open access environment may try to purchase the energy from the cheaper source for greater profit margins, which may lead to overloading and congestion of certain corridors of the transmission network. This may result in violation of line flow, voltage and stability limits and thereby undermine the system security. Utilities therefore need to determine adequately their available transfer capability (ATC) to ensure that system reliability is maintained while serving a wide range of bilateral and multilateral transactions. This paper presents power transfer distribution factor based on AC load flow for the determination and enhancement of ATC. The study has been carried out for IEEE 24 bus Reliability Test System.
Abstract: The development of an low cost acquisition system of S-EMG signals which are reliable, comfortable for the user and with high mobility shows to be a relevant proposition in modern biomedical engineering scenario. In the study, the sampling capacity of the Arduino microcontroller Atmel Atmega328 with an A / D converter with 10-bit resolution and its reconstructing capability of a signal of surface electromyography is analyzed. An electronic circuit to capture the signal through two differential channels was designed, signals from Biceps Brachialis of a healthy man of 21 years was acquired to test the system prototype. ARV, MDF, MNF and RMS estimators were used to compare de acquired signals with physiological values. The Arduino was configured with a sampling frequency of 1.5kHz for each channel, and the tests with the circuit designed offered a SNR of 20.57dB.
Abstract: The calcarenites carbonate rocks of the Quaternary ridges, which extend along the northwestern Mediterranean coastal plain of Egypt, represent an excellent model for the transformation of loose sediments to real sedimentary rocks by the different stages of meteoric diagenesis. The depositional and diagenetic fabrics of the rocks, in addition to the strata orientation, highly affect their ultimate compressive strength and other geotechnical properties.
There is a marked increase in the compressive strength (UCS) from the first to the fourth ridge rock samples. The lowest values are related to the loose packing, weakly cemented aragonitic ooid sediments with high porosity, besides the irregularly distributed of cement, which result in decreasing the ability of these rocks to withstand crushing under direct pressure. The high (UCS) values are attributed to the low porosity, the presence of micritic cement, the reduction in grain size and the occurrence of micritization and calcretization processes.
The strata orientation has a notable effect on the measured (UCS). The lowest values have been recorded for the samples cored in the inclined direction; whereas the highest values have been noticed in most samples cored in the vertical and parallel directions to bedding plane. In case of the inclined direction, the bedding planes were oriented close to the plane of maximum shear stress. The lowest and highest anisotropy values have been recorded for the first and the third ridges rock samples, respectively, which may attributed to the relatively homogeneity and well sorted grainstone of the first ridge rock samples, and relatively heterogeneity in grain and pore size distribution and degree of cementation of the third ridge rock samples, besides, the abundance of shell fragments with intraparticle pore spaces, which may produce lines of weakness within the rock.
Abstract: Liquefaction is a phenomenon in which the strength
and stiffness of a soil is reduced by earthquake shaking or other rapid
cyclic loading. Liquefaction and related phenomena have been
responsible for huge amounts of damage in historical earthquakes
around the world.
Modeling of soil behavior is the main step in soil liquefaction
prediction process. Nowadays, several constitutive models for sand
have been presented. Nevertheless, only some of them can satisfy this
mechanism. One of the most useful models in this term is
UBCSAND model. In this research, the capability of this model is
considered by using PLAXIS software. The real data of superstition
hills earthquake 1987 in the Imperial Valley was used. The results of
the simulation have shown resembling trend of the UBC3D-PLM
model.
Abstract: In this work, the main problem considered is the
detection and the isolation of the actuator fault. A new formulation of
the linear system is generated to obtain the conditions of the actuator
fault diagnosis. The proposed method is based on the representation
of the actuator as a subsystem connected with the process system in
cascade manner. The designed formulation is generated to obtain the
conditions of the actuator fault detection and isolation. Detectability
conditions are expressed in terms of the invertibility notions. An
example and a comparative analysis with the classic formulation
illustrate the performances of such approach for simple actuator fault
diagnosis by using the linear model of nuclear reactor.
Abstract: Asymmetric incremental sheet forming (AISF) could significantly reduce costs incurred by the fabrication of complex industrial components with a minimal environmental impact. The AISF experiments were carried out on commercially pure titanium (Ti-Gr2), Timetal (15-3-3-3) alloy, and Ti-6Al-4V (Ti-Gr5) alloy. A special testing geometry was used to characterize the titanium alloys properties from the point of view of the forming zone and titanium structure effect. The structure and properties of the materials were assessed by means of metallographic analyses and microhardness measurements.The highest differences in the parameters assessed as a function of the sampling zone were observed in the case of alpha-phase Ti-Gr2at the expense of the most substantial sheet thinning occurrence. A springback causes a smaller stored deformation in Timetal (β alloy) resulting in less pronounced microstructure refinement and microhardness increase. Ti-6Al-4V alloy exhibited early failure due to its poor formability at ambient temperature.
Abstract: The results of the study on the project evaluation to
develop the competencies, capabilities, and skills in repairing
computers of people in Jompluak Local Municipality, Bang Khonthi
District, Samut Songkram Province showed that the overall result
was good (4.33). When considering on each aspect, it was found that
the highest one was on process evaluation (4.60) followed by product
evaluation (4.50) and the least one was on feeding factor (3.97).
When considering in details, it was found that: 1) the context aspect
was high (4.23) with the highest item on the arrangement of the
training situation (4.67) followed by the appropriateness of the target
(4.30) and the least aspect was on the project cooperation (3.73). 2)
The evaluation of average overall primary factor or feeding factor
showed high value (4.23) while the highest aspect was on the
capability of the trainers (4.47) followed by the suitable venue (4.33)
while the least aspect was on the insufficient budget (3.47). 3) The
average result of process evaluation was very high (4.60). The
highest aspect was on the follow-op supervision (4.70) followed by
responsibility of each project staffs (4.50) while the least aspect was
on the present situation and the problems of the community (4.40). 4)
The overall result of the product evaluation was very high (4.50). The
highest aspect was on the diversity of the activities and the
community integration (4.67) followed by project target achievement
(4.63) while the least aspect was on continuation and regularity of the
activities (4.33). The trainees reported high satisfaction on the project
management at very high level (43.33%) while 40% reported high
level and 16.67% reported moderate level. Suggestions for the project
were on the additional number of the computer sets (37.78%)
followed by longer training period especially on computer skills
(43.48%).
Abstract: The objectives of this research were to study the management of local towns and to develop a better model of town management according to the Philosophy of Sufficiency Economy. This study utilized qualitative research, field research, as well as documentary research at the same time. A total of 10 local towns or Tambons of Supanburi province, Thailand were selected for an in-depth interview. The findings revealed that the model of local town management according to Philosophy of Sufficient Economy was in a level of “good” and the model of management has the five basic guidelines: 1) ability to manage budget information and keep it up-to-date, 2) ability to decision making according to democracy rules, 3) ability to use check and balance system, 4) ability to control, follow, and evaluation, and 5) ability to allow the general public to participate. In addition, the findings also revealed that the human resource management according to Philosophy of Sufficient Economy includes obeying laws, using proper knowledge, and having integrity in five areas: plan, recruit, select, train, and maintain human resources.
Abstract: The two primary objectives of this research were (1)
to examine the current knowledge and actual circumstance of
agricultural workers about mangosteen product processing; and (2) to
analyze and evaluate ways to develop capacity of mangosteen
product processing. The population of this study was 15,125 people
who work in the agricultural sector, in this context, mangosteen
production, in the eastern part of Thailand that included Chantaburi
Province, Rayong Province, Trad Province and Pracheenburi
Province. The sample size based on Yamane’s calculation with 95%
reliability was therefore 392 samples. Mixed method was employed
included questionnaire and focus group discussion with
Connoisseurship Model used in order to collect quantitative and
qualitative data. Key informants were used in the focus group
including agricultural business owners, academic people in agro food
processing, local academics, local community development staff,
OTOP subcommittee, and representatives of agro processing
industry professional organizations. The study found that the
majority of the respondents agreed with a high level (in five- rating
scale) towards most of variables of knowledge management in agro
food processing. The result of the current knowledge and actual
circumstance of agricultural human resource in an arena of
mangosteen product processing revealed that mostly, the respondents
agreed at a high level to establish 7 variables. The guideline to
developing the body of knowledge in order to enhance the capacity
of the agricultural workers in mangosteen product processing was
delivered in the focus group discussion. The discussion finally
contributed to an idea to produce manuals for mangosteen product
processing methods, with 4 products chosen: (1) mangosteen soap;
(2) mangosteen juice; (3) mangosteen toffee; and (4) mangosteen
preserves or jam.
Abstract: Slab sliding system (SSS) with Coulomb friction
interface between slab and supporting frame is a passive structural
vibration control technology. The system can significantly reduce the
slab acceleration and accompanied lateral force of the frame. At the
same time it is expected to cause the slab displacement magnification
by sliding movement. To obtain the general comprehensive seismic
response of a single story structure, inelastic response spectra were
computed for a large ensemble of ground motions and a practical range
of structural periods and friction coefficient values. It was shown that
long period structures have no trade-off relation between force
reduction and displacement magnification with respect to elastic
response, unlike short period structures. For structures with the
majority of mass in the slab, the displacement magnification value can
be predicted according to simple inelastic displacement relation for
inelastically responding SDOF structures because the system behaves
elastically to a SDOF structure.
Abstract: Mangabeira (Hancornia speciosa Gomes), a native plant in Brazil, is found growing spontaneously in various regions of the country. The high perishability of tropical fruits such as mangaba, causes it to be necessary to use technologies that promote conservation, aiming to increase the shelf life of this fruit and add value. The objective of this study was to compare the mangabas lyophilization curves behaviors with different sizes and maturation stages. The fruits were freeze-dried for a period of approximately 45 hours at lyophilizer Liotop brand, model L -108. It has been considered large the fruits between 38 and 58 mm diameter and small, between 23 and 28 mm diameter and the two states of maturation, intermediate and mature. Large size mangabas drying curves in both states of maturation were linear behavior at all process, while the kinetic drying curves related to small fruits, independent of maturation state, had a typical behavior of drying, with all the well-defined steps. With these results it was noted that the time of lyophilization was suitable for small mangabas, a fact that did not happen with the larger one. This may indicate that the large mangabas require a longer time to freeze until reaches the equilibrium level, as it happens with the small fruits, going to have constant moisture at the end of the process. For both types of fruit were analyzed water activity, acidity, protein, lipid, and vitamin C before and after the process.
Abstract: The paper presents an analysis of the innovation performance of small and medium-sized furniture enterprises in Bulgaria, accounting for over 97% of the companies in the sector. It contains advanced features of innovation in enterprises, specific features of the furniture industry in Bulgaria and analysis of the results of studies on the topic. The results from studies of three successive periods - 2006-2008; 2008-2010; 2010-2012, during which were studied 594 small and medium-sized furniture enterprises. There are commonly used in the EU definitions and indicators (European Commission, OECD, Oslo Manual), which allows for the comparability of results.
Abstract: Patients under health treatments that involve long
stays at a hospital or health center (e.g. cancer, organ transplants and
severe burns), tend to get bored or depressed because of the lack of
social interaction with family and friends. Such a situation also
affects the evolution and effectiveness of their treatments. In many
cases, the solution to this problem involves extra challenges, since
many patients need to rest quietly (or remain in bed) to their being
contagious. Considering the weak health condition in which usually
are these kinds, keeping them motivated and quiet represents an
important challenge for nurses and caregivers. This article presents a
mobile ubiquitous game called MagicRace, which allows hospitalized
kinds to interact socially with one another without putting to risk
their sensitive health conditions. The game does not require a
communication infrastructure at the hospital, but instead, it uses a
mobile ad hoc network composed of the handheld devices used by
the kids to play. The usability and performance of this application
was tested in two different sessions. The preliminary results show
that users experienced positive feelings from this experience.
Abstract: The main aim of the current work is to examine if 14N
is candidate to be clusterized nuclei or not. In order to check this
attendance, we have measured the angular distributions for 14N ion
beam elastically scattered on 12C target nuclei at different low
energies; 17.5, 21, and 24.5MeV which are close to the Coulomb
barrier energy for 14N+12C nuclear system. Study of various transfer
reactions could provide us with useful information about the
attendance of nuclei to be in a composite form (core + valence). The
experimental data were analyzed using two approaches;
Phenomenological (Optical Potential) and semi-microscopic (Double
Folding Potential). The agreement between the experimental data and
the theoretical predictions is fairly good in the whole angular range.