Abstract: Network coding has recently attracted attention as an efficient technique in multicast/broadcast services. The problem of finding the optimal network coding mechanism maximizing the bandwidth efficiency is hard to solve and hard to approximate. Lots of network coding-based schemes have been suggested in the literature to improve the bandwidth efficiency, especially network coding-based automatic repeat request (NCARQ) schemes. However, existing schemes have several limitations which cause the performance degradation in resource limited systems. To improve the performance in resource limited systems, we propose NCARQ with overlapping selection (OS-NCARQ) scheme. The advantages of OS-NCARQ scheme over the traditional ARQ scheme and existing NCARQ schemes are shown through the analysis and simulations.
Abstract: The machining performance is determined by the
frequency characteristics of the machine-tool structure and the
dynamics of the cutting process. Therefore, the prediction of dynamic
vibration behavior of spindle tool system is of great importance for the
design of a machine tool capable of high-precision and high-speed
machining. The aim of this study is to develop a finite element model
to predict the dynamic characteristics of milling machine tool and
hence evaluate the influence of the preload of the spindle bearings. To
this purpose, a three dimensional spindle bearing model of a high
speed engraving spindle tool was created. In this model, the rolling
interfaces with contact stiffness defined by Harris model were used to
simulate the spindle bearing components. Then a full finite element
model of a vertical milling machine was established by coupling the
spindle tool unit with the machine frame structure. Using this model,
the vibration mode that had a dominant influence on the dynamic
stiffness was determined. The results of the finite element simulations
reveal that spindle bearing with different preloads greatly affect the
dynamic behavior of the spindle tool unit and hence the dynamic
responses of the vertical column milling system. These results were
validated by performing vibration on the individual spindle tool unit
and the milling machine prototype, respectively. We conclude that
preload of the spindle bearings is an important component affecting
the dynamic characteristics and machining performance of the entire
vertical column structure of the milling machine.
Abstract: This article is devoted to the numerical solution of
large-scale quadratic eigenvalue problems. Such problems arise in
a wide variety of applications, such as the dynamic analysis of
structural mechanical systems, acoustic systems, fluid mechanics,
and signal processing. We first introduce a generalized second-order
Krylov subspace based on a pair of square matrices and two initial
vectors and present a generalized second-order Arnoldi process for
constructing an orthonormal basis of the generalized second-order
Krylov subspace. Then, by using the projection technique and the
refined projection technique, we propose a restarted generalized
second-order Arnoldi method and a restarted refined generalized
second-order Arnoldi method for computing some eigenpairs of largescale
quadratic eigenvalue problems. Some theoretical results are also
presented. Some numerical examples are presented to illustrate the
effectiveness of the proposed methods.
Abstract: By the application of an improved back-propagation
neural network (BPNN), a model of current densities for a solid oxide
fuel cell (SOFC) with 10 layers is established in this study. To build
the learning data of BPNN, Taguchi orthogonal array is applied to
arrange the conditions of operating parameters, which totally 7 factors
act as the inputs of BPNN. Also, the average current densities
achieved by numerical method acts as the outputs of BPNN.
Comparing with the direct solution, the learning errors for all learning
data are smaller than 0.117%, and the predicting errors for 27
forecasting cases are less than 0.231%. The results show that the
presented model effectively builds a mathematical algorithm to predict
performance of a SOFC stack immediately in real time.
Also, the calculating algorithms are applied to proceed with the
optimization of the average current density for a SOFC stack. The
operating performance window of a SOFC stack is found to be
between 41137.11 and 53907.89. Furthermore, an inverse predicting
model of operating parameters of a SOFC stack is developed here by
the calculating algorithms of the improved BPNN, which is proved to
effectively predict operating parameters to achieve a desired
performance output of a SOFC stack.
Abstract: Architecture as a form of art, whilst actively
developing, finds new methods and conceptions. Currently,
architectural animation is actively developing as a step, successive to
architectural visualization. Interesting vistas of architectural ideas
were discovered by artists of Japanese animation, in which there are
traditional spirits, kami, and imaginary spaces relating to them.
Anime art should be considered abstract painting, another kind of an
architectural workshop, where new architectural ideas are generated.
Abstract: Automatic detection of syllable repetition is one of the
important parameter in assessing the stuttered speech objectively.
The existing method which uses artificial neural network (ANN)
requires high levels of agreement as prerequisite before attempting to
train and test ANNs to separate fluent and nonfluent. We propose
automatic detection method for syllable repetition in read speech for
objective assessment of stuttered disfluencies which uses a novel
approach and has four stages comprising of segmentation, feature
extraction, score matching and decision logic. Feature extraction is
implemented using well know Mel frequency Cepstra coefficient
(MFCC). Score matching is done using Dynamic Time Warping
(DTW) between the syllables. The Decision logic is implemented by
Perceptron based on the score given by score matching. Although
many methods are available for segmentation, in this paper it is done
manually. Here the assessment by human judges on the read speech
of 10 adults who stutter are described using corresponding method
and the result was 83%.
Abstract: We report the electronic structure and optical
properties of NdF3 compound. Our calculations are based on density
functional theory (DFT) using the full potential linearized augmented
plane wave (FPLAPW) method with the inclusion of spin orbit
coupling. We employed the local spin density approximation (LSDA)
and Coulomb-corrected local spin density approximation, known for
treating the highly correlated 4f electrons properly, is able to
reproduce the correct insulating ground state. We find that the
standard LSDA approach is incapable of correctly describing the
electronic properties of such materials since it positions the f-bands
incorrectly resulting in an incorrect metallic ground state. On the
other hand, LSDA + U approximation, known for treating the highly
correlated 4f electrons properly, is able to reproduce the correct
insulating ground state. Interestingly, however, we do not find any
significant differences in the optical properties calculated using
LSDA, and LSDA + U suggesting that the 4f electrons do not play a
decisive role in the optical properties of these compounds. The
reflectivity for NdF3 compound stays low till 7 eV which is
consistent with their large energy gaps. The calculated energy gaps
are in good agreement with experiments. Our calculated reflectivity
compares well with the experimental data and the results are analyzed
in the light of band to band transitions.
Abstract: Concrete pavement has superior durability and longer
structural life than asphalt pavement. Concrete pavement requires
less maintenance compared to asphalt pavement which requires maintenance and major rehabilitation. Use of the concrete pavement
has been grown over the past decade in developing countries. Fibre reinforced concrete (FRC) has been successfully used in design of concrete pavement in past decade. In this research, the effect of fibre
volume fraction in modulus of rupture, load-deflection, equivalent flexural strength (fe,3) and the equivalent flexural strength ratio (Re,3)
has been used in different fibre volume fraction. Crimped-type flat
steel fibre of size 50 x 2.0 x 0.6 mm was used with 1.0%, 1.5% and 2.0% volume fraction. Beam specimens of size 500 x 100 x 100 mm were used for flexural as well as with JCI method for analysis flexural toughness, equivalent flexural strength. It was obtained as the 2% fibre volume fractions; reduce 45% of the concrete pavement
thickness.
Abstract: This paper proposes a novel architecture for developing decision support systems. Unlike conventional decision support systems, the proposed architecture endeavors to reveal the decision-making process such that humans' subjectivity can be incorporated into a computerized system and, at the same time, to preserve the capability of the computerized system in processing information objectively. A number of techniques used in developing the decision support system are elaborated to make the decisionmarking process transparent. These include procedures for high dimensional data visualization, pattern classification, prediction, and evolutionary computational search. An artificial data set is first employed to compare the proposed approach with other methods. A simulated handwritten data set and a real data set on liver disease diagnosis are then employed to evaluate the efficacy of the proposed approach. The results are analyzed and discussed. The potentials of the proposed architecture as a useful decision support system are demonstrated.
Abstract: Keystroke authentication is a new access control system
to identify legitimate users via their typing behavior. In this paper,
machine learning techniques are adapted for keystroke authentication.
Seven learning methods are used to build models to differentiate user
keystroke patterns. The selected classification methods are Decision
Tree, Naive Bayesian, Instance Based Learning, Decision Table, One
Rule, Random Tree and K-star. Among these methods, three of them
are studied in more details. The results show that machine learning
is a feasible alternative for keystroke authentication. Compared to
the conventional Nearest Neighbour method in the recent research,
learning methods especially Decision Tree can be more accurate. In
addition, the experiment results reveal that 3-Grams is more accurate
than 2-Grams and 4-Grams for feature extraction. Also, combination
of attributes tend to result higher accuracy.
Abstract: In this paper, the effect of bolt clamping force on the fatigue behavior of bolted single lap joints of aluminum alloy 2024- T3 have been studied using numerical finite element method. To do so, a three dimensional model according to the bolted single lap joint has been created and numerical analysis has been carried out using finite element based package. Then the stress distribution and also the slip amplitudes have been calculated in the critical regions and the outcome have been compared with the available experimental fatigue tests results. The numerical results show that in low applied clamping force, the fatigue failure of the specimens occur around the stress concentration location (the bolted hole edge) due to the tensile stresses and thus fatigue crack propagation, but with increase of the clamping force, the fatigue life increases and the cracks nucleate and propagate far from the hole edge because of fretting fatigue. In other words, with the further increase of clamping force value of the joint, the fatigue life reduces due to occurrence of the fretting fatigue in the critical location where the slip amplitude is within its critical occurs earlier.
Abstract: The main goal of the study is to analyze all relevant
properties of the electro hydraulic systems and based on that to make
a proper choice of the control strategy that may be used for the
control of the servomechanism system. A combination of electronic
and hydraulic systems is widely used since it combines the
advantages of both. Hydraulic systems are widely spread because of
their properties as accuracy, flexibility, high horsepower-to-weight
ratio, fast starting, stopping and reversal with smoothness and
precision, and simplicity of operations. On the other hand, the
modern control of hydraulic systems is based on control of the circuit
fed to the inductive solenoid that controls the position of the
hydraulic valve. Since this circuit may be easily handled by PWM
(Pulse Width Modulation) signal with a proper frequency, the
combination of electrical and hydraulic systems became very fruitful
and usable in specific areas as airplane and military industry.
The study shows and discusses the experimental results obtained
by the control strategy (classical feedback (PID) & neural network)
using MATLAB and SIMULINK [1]. Finally, the special attention
was paid to the possibility of neuro-controller design and its
application to control of electro-hydraulic systems and to make
comparative with classical control.
Abstract: Mixed model assembly lines (MMAL) are a type of
production line where a variety of product models similar in product
characteristics are assembled. The effective design of these lines
requires that schedule for assembling the different products is
determined. In this paper we tried to fit the sequencing problem with
the main characteristics of make to order (MTO) environment. The
problem solved in this paper is a multiple objective sequencing
problem in mixed model assembly lines sequencing using weighted
Sum Method (WSM) using GAMS software for small problem and
an effective GA for large scale problems because of the nature of
NP-hardness of our problem and vast time consume to find the
optimum solution in large problems. In this problem three practically
important objectives are minimizing: total utility work, keeping a
constant production rate variation, and minimizing earliness and
tardiness cost which consider the priority of each customer and
different due date which is a real situation in mixed model assembly
lines and it is the first time we consider different attribute to
prioritize the customers which help the company to reduce the cost of
earliness and tardiness. This mechanism is a way to apply an advance
available to promise (ATP) in mixed model assembly line sequencing
which is the main contribution of this paper.
Abstract: Real-time hand tracking is a challenging task in many
computer vision applications such as gesture recognition. This paper
proposes a robust method for hand tracking in a complex environment
using Mean-shift analysis and Kalman filter in conjunction with 3D
depth map. The depth information solve the overlapping problem
between hands and face, which is obtained by passive stereo measuring
based on cross correlation and the known calibration data of
the cameras. Mean-shift analysis uses the gradient of Bhattacharyya
coefficient as a similarity function to derive the candidate of the hand
that is most similar to a given hand target model. And then, Kalman
filter is used to estimate the position of the hand target. The results
of hand tracking, tested on various video sequences, are robust to
changes in shape as well as partial occlusion.
Abstract: Exploring an autistic child in Elementary school is a
difficult task that must be fully thought out and the teachers should
be aware of the many challenges they face raising their child
especially the behavioral problems of autistic children. Hence there
arises a need for developing Artificial intelligence (AI)
Contemporary Techniques to help diagnosis to discover autistic
people.
In this research, we suggest designing architecture of expert
system that combine Cognitive Maps (CM) with Case Based
Reasoning technique (CBR) in order to reduce time and costs of
traditional diagnosis process for the early detection to discover
autistic children. The teacher is supposed to enter child's information
for analyzing by CM module. Then, the reasoning processor would
translate the output into a case to be solved a current problem by
CBR module. We will implement a prototype for the model as a
proof of concept using java and MYSQL.
This will be provided a new hybrid approach that will achieve new
synergies and improve problem solving capabilities in AI. And we
will predict that will reduce time, costs, the number of human errors
and make expertise available to more people who want who want to
serve autistic children and their families.
Abstract: Many states are now committed to implementing
international human rights standards domestically. In terms of
practical governance, how might effectiveness be measured? A facevalue
answer can be found in domestic laws and institutions relating
to human rights. However, this article provides two further tools to
help states assess their status on the spectrum of robust to fragile
human rights governance. The first recognises that each state has its
own 'human rights history' and the ideal end stage is robust human
rights governance, and the second is developing criteria to assess
robustness. Although a New Zealand case study is used to illustrate
these tools, the widespread adoption of human rights standards by
many states inevitably means that the issues are relevant to other
countries. This is even though there will always be varying degrees of
similarity-difference in constitutional background and developed or
emerging human rights systems.
Abstract: This study was designed to formulate,
pharmaceutically evaluate a topical skin-care cream (w/o emulsion)
of Aloe Vera versus its vehicle (Base) as control and determine their
effects on Stratum Corneum (SC) water content and Transepidermal
water loss (TEWL). Base containing no extract and a Formulation
containing 3% concentrated extract of Aloe Vera was developed by
entrapping in the inner aqueous phase of w/o emulsion (cream).
Lemon oil was incorporated to improve the odor. Both the Base and
Formulation were stored at 8°C ±0.1°C (in refrigerator), 25°C±0.1°C,
40°C±0.1°C and 40°C± 0.1°C with 75% RH (in incubator) for a
period of 4 weeks to predict their stability. The evaluation parameters
consisted of color, smell, type of emulsion, phase separation,
electrical conductivity, centrifugation, liquefaction and pH. Both the
Base and Formulation were applied to the cheeks of 21 healthy
human volunteers for a period of 8 weeks Stratum corneum (SC)
water content and Transepidermal water loss (TEWL) were
monitored every week to measure any effect produced by these
topical creams. The expected organoleptic stability of creams was
achieved from 4 weeks in-vitro study period. Odor was disappeared
with the passage of time due to volatilization of lemon oil. Both the
Base and Formulation produced significant (p≤0.05) changes in
TEWL with respect to time. SC water content was significantly
(p≤0.05) increased by the Formulation while the Base has
insignificant (p 0.05) effects on SC water content. The newly
formulated cream of Aloe Vera, applied is suitable for improvement
and quantitative monitoring of skin hydration level (SC water
content/ moisturizing effects) and reducing TEWL in people with dry
skin.
Abstract: Size based filtration is one of the common methods
employed to isolate circulating tumor cells (CTCs) from whole
blood. It is well known that this method suffers from isolation
efficiency to purity tradeoff. However, this tradeoff is poorly
understood. In this paper, we present the design and manufacturing
of a special rectangular slit filter. The filter was designed to retain
maximal amounts of nucleated cells, while minimizing the pressure
on cells, thereby preserving their morphology. The key parameter,
namely, input pressure, was optimized to retain the maximal number
of tumor cells, whilst maximizing the depletion of normal blood cells
(red and white blood cells and platelets). Our results indicate that for
a slit geometry of 5 × 40 μm on a 13 mm circular membrane with a
fill factor of 21%, a pressure of 6.9 mBar yields the optimum for
maximizing isolation of MCF-7 and depletion of normal blood cells.
Abstract: Increasing the demand for effectively use of the
production facility requires the tools for sharing the manufacturing
facility through remote operation of the machining process. This
research introduces the methodology of machining technology for
direct remote operation of networked milling machine. The
integrated tools with virtual simulation, remote desktop protocol and
Setup Free Attachment for remote operation of milling process are
proposed. Accessing and monitoring of machining operation is
performed by remote desktop interface and 3D virtual simulations.
Capability of remote operation is supported by an auto setup
attachment with a reconfigurable pin type setup free technology
installed on the table of CNC milling machine to perform unattended
machining process. The system is designed using a computer server
and connected to a PC based controlled CNC machine for real time
monitoring. A client will access the server through internet
communication and virtually simulate the machine activity. The
result has been presented that combination between real time virtual
simulation and remote desktop tool is enabling to operate all machine
tool functions and as well as workpiece setup..
Abstract: Graph has become increasingly important in modeling
complicated structures and schemaless data such as proteins, chemical
compounds, and XML documents. Given a graph query, it is desirable
to retrieve graphs quickly from a large database via graph-based
indices. Different from the existing methods, our approach, called
VFM (Vertex to Frequent Feature Mapping), makes use of vertices
and decision features as the basic indexing feature. VFM constructs
two mappings between vertices and frequent features to answer graph
queries. The VFM approach not only provides an elegant solution to
the graph indexing problem, but also demonstrates how database
indexing and query processing can benefit from data mining,
especially frequent pattern mining. The results show that the proposed
method not only avoids the enumeration method of getting subgraphs
of query graph, but also effectively reduces the subgraph isomorphism
tests between the query graph and graphs in candidate answer set in
verification stage.