Abstract: The dispersion of heavy particles line in an isotropic
and incompressible three-dimensional turbulent flow has been
studied using the Kinematic Simulation techniques to find out the
evolution of the line fractal dimension. In this study, the fractal
dimension of the line is found for different cases of heavy particles
inertia (different Stokes numbers) in the absence of the particle
gravity with a comparison with the fractal dimension obtained in the
diffusion case of material line at the same Reynolds number. It can
be concluded for the dispersion of heavy particles line in turbulent
flow that the particle inertia affect the fractal dimension of a line
released in a turbulent flow for Stokes numbers 0.02 < St < 2. At the
beginning for small times, most of the different cases are not affected
by the inertia until a certain time, the particle response time τa, with
larger time as the particles inertia increases, the fractal dimension of
the line increases owing to the particles becoming more sensitive to
the small scales which cause the change in the line shape during its
journey.
Abstract: Different agricultural waste peels were assessed for
their suitability to be used as primary substrates for the
bioremediation of free cyanide (CN-) by a cyanide-degrading fungus
Aspergillus awamori isolated from cyanide containing wastewater.
The bioremediated CN- concentration were in the range of 36 to 110
mg CN-/L, with Orange (C. sinensis) > Carrot (D. carota) > Onion
(A. cepa) > Apple (M. pumila), being chosen as suitable substrates
for large scale CN- degradation processes due to: 1) the high
concentration of bioremediated CN-, 2) total reduced sugars released
into solution to sustain the biocatalyst, and 3) minimal residual NH4-
N concentration after fermentation. The bioremediation rate constants
(k) were 0.017h-1 (0h < t < 24h), with improved bioremediation rates
(0.02189h-1) observed after 24h. The averaged nitrilase activity was
~10 U/L.
Abstract: Polyurethane foams (PUF) were formed by a chemical
reaction of polyol and isocyanate. The polyol was manufactured by
ring-opening hydrolysis of epoxidized soybean oil in the presence of
phosphoric acid under varying experimental conditions. Other
factors in the foam formulation such as water content and surfactant
were kept constant. The effect of the amount of solvents, phosphoric
acid, and their derivates in the foam formulation on the properties of
polyurethane foams were studied. The properties of the material were
measured via a number of parameters, which are water content of
prepared polyol, polymer density and cellular structures.
Abstract: The Brazilian legislation has only established
diagnostic reference levels (DRLs) in terms of Multiple Scan
Average Dose (MSAD) as a quality control parameter for computed
tomography (CT) scanners. Compliance with DRLs can be verified
by measuring the Computed Tomography Kerma Index (Ca,100) with
a pencil ionization chamber or by obtaining the kerma distribution in
CT scans with radiochromic films or rod shape lithium fluoride
termoluminescent dosimeters (TLD-100). TL dosimeters were used
to record kerma profiles and to determine MSAD values of a Bright
Speed model GE CT scanner. Measurements were done with
radiochromic films and TL dosimeters distributed in cylinders
positioned in the center and in four peripheral bores of a standard
polymethylmethacrylate (PMMA) body CT dosimetry phantom.
Irradiations were done using a protocol for adult chest. The
maximum values were found at the midpoint of the longitudinal axis.
The MSAD values obtained with three dosimetric techniques were
compared.
Abstract: In this paper a controller for the pitch angle of an
aircraft regarding to the elevator deflection angle is designed.
The way how the elevator angle affects pitching motion of the
aircraft is pointed out, as well as, how a pitch controller can be
applied for the aircraft to reach certain pitch angle. In this digital
optimal system, the elevator deflection angle and pitching angle
of the plane are considered to be input and output respectively.
A single input single output (SISO) system is presented. A
digital pitch aircraft control is demonstrated. A simulation for
the whole system has been performed. The optimal control
weighting vectors, Q and R have been determined.
Abstract: The purpose of the experiments described in this article was the comparison of integrated fixed film activated sludge (IFAS) and activated sludge (AS) system. The IFAS applied system consists of the cigarette filter rods (wasted filter in tobacco factories) as a biofilm carrier. The comparison with activated sludge was performed by two parallel treatment lines. Organic substance, ammonia and TP removal was investigated over four month period. Synthetic wastewater was prepared with ordinary tap water and glucose as the main sources of carbon and energy, plus balanced macro and micro nutrients. COD removal percentages of 94.55%, and 81.62% were achieved for IFAS and activated sludge system, respectively. Also, ammonia concentration significantly decreased by increasing the HRT in both systems. The average ammonia removal of 97.40 % and 96.34% were achieved for IFAS and activated sludge system, respectively. The removal efficiency of total phosphorus (TP-P) was 60.64%, higher than AS process by 56.63% respectively.
Abstract: Meeting users- requirements is one of predictors of project success. There should be a match between the expectations of the users and the perception of key project personnel with respect to usability and functionality. The aim of this study is to make a comparison of key project personnel-s and potential users- (customer representatives) evaluations of the relative importance of usability and functionality factors in a software design project. Analytical Network Process (ANP) was used to analyze the relative importance of the factors. The results show that navigation and interaction are the most significant factors,andsatisfaction and efficiency are the least important factors for both groups. Further, it can be concluded that having similar orders and scores of usability and functionality factors for both groups shows that key project personnel have captured the expectations and requirements of potential users accurately.
Abstract: Vermicomposting is the conversion of organic waste
into bio-fertilizers through the action of earthworm. This technology
is widely used for organic solid waste management. Waste corn pulp
blended with cow dung manure was vermicomposted over 30 days
using Eisenia fetida earthworms species. pH, temperature, moisture
content, and electrical conductivity were daily monitored. The
feedstock, vermicompost and vermiwash were analyzed for nutrient
composition. The average temperature and moisture content in the
vermi-reactor was 22.5°C and 42.5% respectively. The vermicompost
and vermiwash had an almost neutral pH whilst the electrical
conductivity was 21% higher in the vermicompost. The nitrogen and
potassium content was 57% and 79.6% richer in the vermicompost
respectively compared to the vermiwash. However, the vermiwash
was 84% richer in phosphorous as compared to vermicompost.
Furthermore, the vermiwash was 89.1% and 97.6% richer in Ca and
Mg respectively and was 97.8% richer in Na salts compared to the
vermicompost. The vermiwash also indicated a significantly higher
amount of micronutrients. Both bio-fertilizers were rich in nutrients
specification for fertilizers.
Abstract: Poly (ethylene glycol) (PEG) molecules attached to surfaces have shown high potential as a protein repellent due to their flexibility and highly water solubility. A quartz crystal microbalance recording frequency and dissipation changes (QCM-D) has been used to study the adsorption from aqueous solutions, of lysozyme and α-lactalbumin proteins (the last with and without calcium) onto modified stainless steel surfaces. Surfaces were coated with poly(ethylene imine) (PEI) and silicate before grafting on PEG molecules. Protein adsorption was also performed on the bare stainless steel surface as a control. All adsorptions were conducted at 23°C and pH 7.2. The results showed that the presence of PEG molecules significantly reduced the adsorption of lysozyme and α- lactalbumin (with calcium) onto the stainless steel surface. By contrast, and unexpected, PEG molecules enhanced the adsorption of α-lactalbumin (without calcium). It is suggested that the PEG -α- lactalbumin hydrophobic interaction plays a dominant role which leads to protein aggregation at the surface for this latter observation. The findings also lead to the general conclusion that PEG molecules are not a universal protein repellent. PEG-on-PEI surfaces were better at inhibiting the adsorption of lysozyme and α-lactalbumin (with calcium) than with PEG-on-silicate surfaces.
Abstract: This paper deals with new concept of using compressed atmospheric air as a zero pollution power source for running motorbikes. The motorbike is equipped with an air turbine in place of an internal combustion engine, and transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor to casing diameter ratios with respect to different vane angles (number of vanes) have been considered and analyzed. It is found that the shaft work output is optimum for some typical values of rotor / casing diameter ratios at a particular value of vane angle (no. of vanes). In this study, the maximum power is obtained as 4.5kW - 5.3kW (5.5-6.25 HP) when casing diameter is taken 100 mm, and rotor to casing diameter ratios are kept from 0.65 to 0.55. This value of output is sufficient to run motorbike.
Abstract: This paper presented two new efficient algorithms
for contour approximation. The proposed algorithm is compared
with Ramer (good quality), Triangle (faster) and Trapezoid (fastest)
in this work; which are briefly described. Cartesian co-ordinates of
an input contour are processed in such a manner that finally
contours is presented by a set of selected vertices of the edge of the
contour. In the paper the main idea of the analyzed procedures for
contour compression is performed. For comparison, the mean
square error and signal-to-noise ratio criterions are used.
Computational time of analyzed methods is estimated depending on
a number of numerical operations. Experimental results are
obtained both in terms of image quality, compression ratios, and
speed. The main advantages of the analyzed algorithm is small
numbers of the arithmetic operations compared to the existing
algorithms.
Abstract: We study the performance of compressed beamforming
weights feedback technique in generalized triangular decomposition
(GTD) based MIMO system. GTD is a beamforming technique that
enjoys QoS flexibility. The technique, however, will perform at its
optimum only when the full knowledge of channel state information
(CSI) is available at the transmitter. This would be impossible in
the real system, where there are channel estimation error and limited
feedback. We suggest a way to implement the quantized beamforming
weights feedback, which can significantly reduce the feedback data,
on GTD-based MIMO system and investigate the performance of
the system. Interestingly, we found that compressed beamforming
weights feedback does not degrade the BER performance of the
system at low input power, while the channel estimation error
and quantization do. For comparison, GTD is more sensitive to
compression and quantization, while SVD is more sensitive to the
channel estimation error. We also explore the performance of GTDbased
MU-MIMO system, and find that the BER performance starts
to degrade largely at around -20 dB channel estimation error.
Abstract: This paper deals with the thermo-mechanical deformation behavior of shear deformable functionally graded ceramicmetal (FGM) plates. Theoretical formulations are based on higher order shear deformation theory with a considerable amendment in the transverse displacement using finite element method (FEM). The mechanical properties of the plate are assumed to be temperaturedependent and graded in the thickness direction according to a powerlaw distribution in terms of the volume fractions of the constituents. The temperature field is supposed to be a uniform distribution over the plate surface (XY plane) and varied in the thickness direction only. The fundamental equations for the FGM plates are obtained using variational approach by considering traction free boundary conditions on the top and bottom faces of the plate. A C0 continuous isoparametric Lagrangian finite element with thirteen degrees of freedom per node have been employed to accomplish the results. Convergence and comparison studies have been performed to demonstrate the efficiency of the present model. The numerical results are obtained for different thickness ratios, aspect ratios, volume fraction index and temperature rise with different loading and boundary conditions. Numerical results for the FGM plates are provided in dimensionless tabular and graphical forms. The results proclaim that the temperature field and the gradient in the material properties have significant role on the thermo-mechanical deformation behavior of the FGM plates.
Abstract: Kuwait-s electric power system is vertically integrated
organization owned and operated by the government. For more than
five decades, the government of Kuwait has provided relatively
reliable electric services to consumers with subsidized electric
service fees. Given the country-s rapid socio-economical
development and consequently the increase of electricity demand, a
question that inflicts itself: Is it necessary to reform the power system
to face the fast growing demand? This paper recommends that the
government should consider the private sector as a partner in
operating the power system. Therefore, power system restructuring is
needed to allow such partnership. There are challenges that prevent
such restructuring. Abstract recommendations toward resolving these
challenges are proposed.
Abstract: This article is a piece of the doctoral thesis
"Syncretism of traditional Kazakh culture in the light of the
innovation direction of circus and choreographic art of Kazakhstan
and its integration into the world civilization", and reveals the
features of the creative personalities of the traditional culture of
shamans, sals, seris, paluans in the comparative characteristic of the
European histriones and Russian skomorokhs.
Abstract: Image interpolation is a common problem in imaging applications. However, most interpolation algorithms in existence suffer visually the effects of blurred edges and jagged artifacts in the image to some extent. This paper presents an adaptive feature preserving bidirectional flow process, where an inverse diffusion is performed to sharpen edges along the normal directions to the isophote lines (edges), while a normal diffusion is done to remove artifacts (“jaggies") along the tangent directions. In order to preserve image features such as edges, corners and textures, the nonlinear diffusion coefficients are locally adjusted according to the directional derivatives of the image. Experimental results on synthetic images and nature images demonstrate that our interpolation algorithm substantially improves the subjective quality of the interpolated images over conventional interpolations.
Abstract: In text categorization problem the most used method
for documents representation is based on words frequency vectors
called VSM (Vector Space Model). This representation is based only
on words from documents and in this case loses any “word context"
information found in the document. In this article we make a
comparison between the classical method of document representation
and a method called Suffix Tree Document Model (STDM) that is
based on representing documents in the Suffix Tree format. For the
STDM model we proposed a new approach for documents
representation and a new formula for computing the similarity
between two documents. Thus we propose to build the suffix tree
only for any two documents at a time. This approach is faster, it has
lower memory consumption and use entire document representation
without using methods for disposing nodes. Also for this method is
proposed a formula for computing the similarity between documents,
which improves substantially the clustering quality. This
representation method was validated using HAC - Hierarchical
Agglomerative Clustering. In this context we experiment also the
stemming influence in the document preprocessing step and highlight
the difference between similarity or dissimilarity measures to find
“closer" documents.
Abstract: The purpose of this study is to introduce a new
interface program to calculate a dose distribution with Monte Carlo method in complex heterogeneous systems such as organs or tissues
in proton therapy. This interface program was developed under
MATLAB software and includes a friendly graphical user interface
with several tools such as image properties adjustment or results display. Quadtree decomposition technique was used as an image
segmentation algorithm to create optimum geometries from Computed Tomography (CT) images for dose calculations of proton
beam. The result of the mentioned technique is a number of nonoverlapped
squares with different sizes in every image. By this way
the resolution of image segmentation is high enough in and near
heterogeneous areas to preserve the precision of dose calculations
and is low enough in homogeneous areas to reduce the number of
cells directly. Furthermore a cell reduction algorithm can be used to combine neighboring cells with the same material. The validation of this method has been done in two ways; first, in comparison with experimental data obtained with 80 MeV proton beam in Cyclotron
and Radioisotope Center (CYRIC) in Tohoku University and second, in comparison with data based on polybinary tissue calibration method, performed in CYRIC. These results are presented in this paper. This program can read the output file of Monte Carlo code while region of interest is selected manually, and give a plot of dose distribution of proton beam superimposed onto the CT images.
Abstract: In this paper a bank of velocity filters is devised to be
used for isolating a moving object with specific velocity in a sequence of frames. The approach used is a 3-D FFT based experimental procedure without applying any theoretical concept
from velocity filters. Accordingly, velocity filters are built using the
spectral signature of each separate moving object. Experimentation
reveals the capabilities of the constructed filter bank to separate moving objects as far as the amplitude as well as the direction of the
velocity are concerned.
Abstract: The normalized difference vegetation index (NDVI)
and normalized difference moisture index (NDMI) derived from the
moderate resolution imaging spectroradiometer (MODIS) have been
widely used to identify spatial information of drought condition. The
relationship between NDVI and NDMI has been analyzed using
Pearson correlation analysis and showed strong positive relationship.
The drought indices have detected drought conditions and identified
spatial extents of drought. A comparison between normal year and
drought year demonstrates that the amplitude analysis considered both
vegetation and moisture condition is an effective method to identify
drought condition. We proposed the amplitude analysis is useful for
quick spatial assessment of drought information at a regional scale.