Abstract: One of the primary uses of higher order statistics in
signal processing has been for detecting and estimation of non-
Gaussian signals in Gaussian noise of unknown covariance. This is
motivated by the ability of higher order statistics to suppress additive
Gaussian noise. In this paper, several methods to test for non-
Gaussianity of a given process are presented. These methods include
histogram plot, kurtosis test, and hypothesis testing using cumulants
and bispectrum of the available sequence. The hypothesis testing is
performed by constructing a statistic to test whether the bispectrum
of the given signal is non-zero. A zero bispectrum is not a proof of
Gaussianity. Hence, other tests such as the kurtosis test should be
employed. Examples are given to demonstrate the performance of the
presented methods.
Abstract: This paper addresses the problems encountered by conventional distance relays when protecting double-circuit transmission lines. The problems arise principally as a result of the mutual coupling between the two circuits under different fault conditions; this mutual coupling is highly nonlinear in nature. An adaptive protection scheme is proposed for such lines based on application of artificial neural network (ANN). ANN has the ability to classify the nonlinear relationship between measured signals by identifying different patterns of the associated signals. One of the key points of the present work is that only current signals measured at local end have been used to detect and classify the faults in the double circuit transmission line with double end infeed. The adaptive protection scheme is tested under a specific fault type, but varying fault location, fault resistance, fault inception angle and with remote end infeed. An improved performance is experienced once the neural network is trained adequately, which performs precisely when faced with different system parameters and conditions. The entire test results clearly show that the fault is detected and classified within a quarter cycle; thus the proposed adaptive protection technique is well suited for double circuit transmission line fault detection & classification. Results of performance studies show that the proposed neural network-based module can improve the performance of conventional fault selection algorithms.
Abstract: An innovative approach utilizing highly alkaline oil
shale waste ash and carbon dioxide gas (CO2), associated with power
production, as a resource for production of precipitated calcium
carbonate (PCC) is introduced in this paper. The specifics and
feasibility of the integrated ash valorization and CO2 sequestration
process by indirect aqueous carbonation of lime-consisting ash were
elaborated and the main parameters established. Detailed description
of the formed precipitates was included. Complimentary carbonation
experiments with commercial CaO fine powder were conducted for
comparative characterization of the final products obtained on the
basis of two different raw materials. Finally, the expected CO2
uptake was evaluated.
Abstract: The C3 plants are frequently suffering from exposure
to high temperature stress which limits the growth and yield of these
plants. This study seeks to clarify the physiological mechanisms of
heat tolerance in relation to oxidative stress in C3 species. Fifteen C3
species were exposed to prolonged moderately high temperature
stress 36/30°C for 40 days in a growth chamber. Chlorophyll
fluorescence (Fv/Fm) showed great difference among species at 40
days of the stress. The species showed decreases in Fv/Fm and
increases in malondialdehyde (MDA) content under stress condition
as well as negative correlation between Fv/Fm and MDA (r = -0.61*)
at 40 days of the stress. Hydrogen peroxide (H2O2) content before
and after stress in addition to its response under stress showed great
differences among species. The results suggest that the difference in
heat tolerance among C3 species is closely associated with the ability
to suppress oxidative damage but not with the content of reactive
oxygen species (ROS) which is regulated by complex network.
Abstract: When studying electronics, hands-on experience is considered to be very valuable for a better understanding of the concepts of electricity and electronics. Students lacking sufficient time in the lab are often put at disadvantage. A way to overcome this, is by using interactive multimedia in a virtual environment. Instead of proposing another new ad-hoc simulator for e-learning, we propose in this paper an e-learning platform integrating the SPICE simulator as a web service. This enables to make use of all the functions of the de-facto standard simulator SPICE inelectronics when developing new simulations.
Abstract: The objective of positioning the fixture elements in
the fixture is to make the workpiece stiff, so that geometric errors in
the manufacturing process can be reduced. Most of the work for
optimal fixture layout used the minimization of the sum of the nodal
deflection normal to the surface as objective function. All deflections
in other direction have been neglected. We propose a new method for
fixture layout optimization in this paper, which uses the element
strain energy. The deformations in all the directions have been
considered in this way. The objective function in this method is to
minimize the sum of square of element strain energy. Strain energy
and stiffness are inversely proportional to each other. The
optimization problem is solved by the sequential quadratic
programming method. Three different kinds of case studies are
presented, and results are compared with the method using nodal
deflections as objective function to verify the propose method.
Abstract: The paper presents an analysis of linkages and
structures of co-operation and their intensity like the potential for the
establishment of clusters in the Central and Eastern (Pannonian)
Croatian. Starting from the theoretical elaboration of the need for
entrepreneurs to organize through the cluster model and the terms of
their self-actualization, related to the importance of traditional values
in terms of benefits, social capital and assess where the company now
is, in order to prove the need to create their own identity in terms of
clustering. The institutional dimensions of social capital where the
public sector has the best role in creating the social structure of
clusters, and social dimensions of social capital in terms of trust,
cooperation and networking will be analyzed to what extent the trust
and coherency are present between companies in the Brod posavina
and Pozega slavonia County, expressed through the readiness of
inclusion in clusters in the NUTS II region - Central and Eastern
(Pannonian) Croatia, as a homogeneous economic entity, with
emphasis on limiting factors that stand in the way of greater
competitiveness.
Abstract: This paper examines the impact of information and
communication technology (ICT) usage, internal relationship,
supplier-retailer relationship, logistics services and inventory
management on convenience store suppliers- performance. Data was
collected from 275 convenience store managers in Malaysia using a
set of questionnaire. The multiple linear regression results indicate
that inventory management, supplier-retailer relationship, logistics
services and internal relationship are predictors of supplier
performance as perceived by convenience store managers. However,
ICT usage is not a predictor of supplier performance. The study
focuses only on convenience stores and petrol station convenience
stores and concentrates only on managers. The results provide
insights to suppliers who serve convenience stores and possibly
similar retail format on factors to consider in improving their service
to retailers. The results also provide insights to government in its
aspiration to improve business operations of convenience store to
consider ways to enhance the adoption of ICT by retailers and
suppliers.
Abstract: A wide spectrum of systems require reliable
personal recognition schemes to either confirm or determine the
identity of an individual person. This paper considers multimodal
biometric system and their applicability to access control,
authentication and security applications. Strategies for feature
extraction and sensor fusion are considered and contrasted. Issues
related to performance assessment, deployment and standardization
are discussed. Finally future directions of biometric systems
development are discussed.
Abstract: The state of the art in instructional design for
computer-assisted learning has been strongly influenced by advances
in information technology, Internet and Web-based systems. The
emphasis of educational systems has shifted from training to
learning. The course delivered has also been changed from large
inflexible content to sequential small chunks of learning objects. The
concepts of learning objects together with the advanced technologies
of Web and communications support the reusability, interoperability,
and accessibility design criteria currently exploited by most learning
systems. These concepts enable just-in-time learning. We propose to
extend theses design criteria further to include the learnability
concept that will help adapting content to the needs of learners. The
learnability concept offers a better personalization leading to the
creation and delivery of course content more appropriate to
performance and interest of each learner. In this paper we present a
new framework of learning environments containing knowledge
discovery as a tool to automatically learn patterns of learning
behavior from learners' profiles and history.
Abstract: Laser soldering is based on applying some soldering material (albumin) onto the approximated edges of the cut and heating the solder (and the underlying tissues) by a laser beam. Endogenous and exogenous materials such as indocyanine green (ICG) are often added to solders to enhance light absorption. Gold nanoshells are new materials which have an optical response dictated by the plasmon resonance. The wavelength at which the resonance occurs depends on the core and shell sizes, allowing nanoshells to be tailored for particular applications. The purposes of this study was use combination of ICG and different concentration of gold nanoshells for skin tissue soldering and also to examine the effect of laser soldering parameters on the properties of repaired skin. Two mixtures of albumin solder and different combinations of ICG and gold nanoshells were prepared. A full thickness incision of 2×20 mm2 was made on the surface and after addition of mixtures it was irradiated by an 810nm diode laser at different power densities. The changes of tensile strength σt due to temperature rise, number of scan (Ns), and scan velocity (Vs) were investigated. The results showed at constant laser power density (I), σt of repaired incisions increases by increasing the concentration of gold nanoshells in solder, Ns and decreasing Vs. It is therefore important to consider the tradeoff between the scan velocity and the surface temperature for achieving an optimum operating condition. In our case this corresponds to σt =1800 gr/cm2 at I~ 47 Wcm-2, T ~ 85ºC, Ns =10 and Vs=0.3mms-1.
Abstract: A clustering based technique has been developed and implemented for Short Term Load Forecasting, in this article. Formulation has been done using Mean Absolute Percentage Error (MAPE) as an objective function. Data Matrix and cluster size are optimization variables. Model designed, uses two temperature variables. This is compared with six input Radial Basis Function Neural Network (RBFNN) and Fuzzy Inference Neural Network (FINN) for the data of the same system, for same time period. The fuzzy inference system has the network structure and the training procedure of a neural network which initially creates a rule base from existing historical load data. It is observed that the proposed clustering based model is giving better forecasting accuracy as compared to the other two methods. Test results also indicate that the RBFNN can forecast future loads with accuracy comparable to that of proposed method, where as the training time required in the case of FINN is much less.
Abstract: Radio Frequency Identification (RFID) initially introduced
during WW-II, has revolutionized the world with its numerous
benefits and plethora of implementations in diverse areas ranging
from manufacturing to agriculture to healthcare to hotel management.
This work reviews the current research in this area with emphasis
on applications for supply chain management and to develop a
taxonomic framework to classify literature which will enable swift
and easy content analysis and also help identify areas for future
research.
Abstract: In the present communication, we have proposed
some new generalized measure of fuzzy entropy based upon real
parameters, discussed their and desirable properties, and presented
these measures graphically. An important property, that is,
monotonicity of the proposed measures has also been studied.
Abstract: Color categorization is shared among members in a
society. This allows communication of color, especially when using
natural language such as English. Hence sociable robot, to live
coexist with human in human society, must also have the shared
color categorization. To achieve this, many works have been done
relying on modeling of human color perception and mathematical
complexities. In contrast, in this work, the computer as brain of the
robot learns color categorization through interaction with humans
without much mathematical complexities.
Abstract: Mechanical design of the thin-film solar framed
module and mounting system is important to enhance module
reliability and to increase areas of applications. The stress induced by
different mounting positions played a main role controlling the
stability of the whole mechanical structure. From the finite element
method, under the pressure from the back of module, the stress at Lc
(center point of the Long frame) increased and the stresses at Center,
Corner and Sc (center point of the Short frame) decreased while the
mounting position was away from the center of the module. In addition,
not only the stress of the glass but also the stress of the frame
decreased. Accordingly it was safer to mount in the position away
from the center of the module. The emphasis of designing frame
system of the module was on the upper support of the Short frame.
Strength of the overall structure and design of the corner were also
important due to the complexity of the stress in the Long frame.
Abstract: In this study, we investigated the effects of ginger and
L-carnitine on the reproductive performance of male rats with respect
to semen parameters, male sex hormones and the testicular
antioxidant system. A total of sixty mature male albino rats were
divided into four groups of fifteen rats. The control group received
saline, whereas the other three groups received ginger (100 mg kg-1 d-
1.), L-carnitine (150 mg kg-1 d-1.) or a combination of both ginger
(100 mg kg-1 d-1.) and L-carnitine (150 mg kg-1 d-1.) via a stomach
tube daily for one month. At the end of the treatment period, the rats
were sacrificed, and their sperm characteristics (count, motility and
viability), antioxidant enzyme factors levels (reduced glutathione,
catalase, superoxide dismutase and total antioxidant capacity) and sex
hormone levels (testosterone, Follicle stimulating hormone(FSH) and
luteinizing hormone (LH) were analysed. Our results showed that the
three experimental treatments improved sperm parameters,
antioxidant enzyme activity and testosterone hormone levels; the
most pronounced positive effects were observed in the group that
received a combination of both ginger and L-carnitine. Therefore, the
administration of a combination of ginger and L-carnitine may be
beneficial for improving male sexual performance.
Abstract: ECG analysis method was developed using ROC
analysis of PVC detecting algorithm. ECG signal of MIT-BIH
arrhythmia database was analyzed by MATLAB. First of all, the
baseline was removed by median filter to preprocess the ECG signal.
R peaks were detected for ECG analysis method, and normal VCG
was extracted for VCG analysis method. Four PVC detecting
algorithm was analyzed by ROC curve, which parameters are
maximum amplitude of QRS complex, width of QRS complex, r-r
interval and geometric mean of VCG. To set cut-off value of
parameters, ROC curve was estimated by true-positive rate
(sensitivity) and false-positive rate. sensitivity and false negative rate
(specificity) of ROC curve calculated, and ECG was analyzed using
cut-off value which was estimated from ROC curve. As a result, PVC
detecting algorithm of VCG geometric mean have high availability,
and PVC could be detected more accurately with amplitude and width
of QRS complex.
Abstract: Named Entity Recognition (NER) aims to classify each word of a document into predefined target named entity classes and is now-a-days considered to be fundamental for many Natural Language Processing (NLP) tasks such as information retrieval, machine translation, information extraction, question answering systems and others. This paper reports about the development of a NER system for Bengali and Hindi using Support Vector Machine (SVM). Though this state of the art machine learning technique has been widely applied to NER in several well-studied languages, the use of this technique to Indian languages (ILs) is very new. The system makes use of the different contextual information of the words along with the variety of features that are helpful in predicting the four different named (NE) classes, such as Person name, Location name, Organization name and Miscellaneous name. We have used the annotated corpora of 122,467 tokens of Bengali and 502,974 tokens of Hindi tagged with the twelve different NE classes 1, defined as part of the IJCNLP-08 NER Shared Task for South and South East Asian Languages (SSEAL) 2. In addition, we have manually annotated 150K wordforms of the Bengali news corpus, developed from the web-archive of a leading Bengali newspaper. We have also developed an unsupervised algorithm in order to generate the lexical context patterns from a part of the unlabeled Bengali news corpus. Lexical patterns have been used as the features of SVM in order to improve the system performance. The NER system has been tested with the gold standard test sets of 35K, and 60K tokens for Bengali, and Hindi, respectively. Evaluation results have demonstrated the recall, precision, and f-score values of 88.61%, 80.12%, and 84.15%, respectively, for Bengali and 80.23%, 74.34%, and 77.17%, respectively, for Hindi. Results show the improvement in the f-score by 5.13% with the use of context patterns. Statistical analysis, ANOVA is also performed to compare the performance of the proposed NER system with that of the existing HMM based system for both the languages.
Abstract: In this article an evolutionary technique has been used
for the solution of nonlinear Riccati differential equations of fractional order. In this method, genetic algorithm is used as a tool for
the competent global search method hybridized with active-set algorithm for efficient local search. The proposed method has been
successfully applied to solve the different forms of Riccati
differential equations. The strength of proposed method has in its
equal applicability for the integer order case, as well as, fractional
order case. Comparison of the method has been made with standard
numerical techniques as well as the analytic solutions. It is found
that the designed method can provide the solution to the equation
with better accuracy than its counterpart deterministic approaches.
Another advantage of the given approach is to provide results on
entire finite continuous domain unlike other numerical methods
which provide solutions only on discrete grid of points.