Abstract: The effect of upstream surface roughness over a
smooth forward facing step in an open channel was investigated
using a particle image velocimetry technique. Three different
upstream surface topographies consisting of hydraulically smooth
wall, sandpaper 36 grit and sand grains were examined. Besides the
wall roughness conditions, all other upstream flow characteristics
were kept constant. It was also observed that upstream roughness
decreased the approach velocity by 2% and 10% but increased the
turbulence intensity by 14% and 35% at the wall-normal distance
corresponding to the top plane of the step compared to smooth
upstream. The results showed that roughness decreased the
reattachment lengths by 14% and 30% compared to smooth upstream.
Although the magnitudes of maximum positive and negative
Reynolds shear stress in separated and reattached region were 0.02Ue
for all the cases, the physical size of both the maximum and
minimum contour levels were decreased by increasing upstream
roughness.
Abstract: The exploitation of flow pulsation in micro- and
mini-channels is a potentially useful technique for enhancing cooling
of high-end photonics and electronics systems. It is thought that
pulsation alters the thickness of the hydrodynamic and thermal
boundary layers, and hence affects the overall thermal resistance
of the heat sink. Although the fluid mechanics and heat transfer
are inextricably linked, it can be useful to decouple the parameters
to better understand the mechanisms underlying any heat transfer
enhancement. Using two-dimensional, two-component particle image
velocimetry, the current work intends to characterize the heat transfer
mechanisms in pulsating flow with a mean Reynolds number of
48 by experimentally quantifying the hydrodynamics of a generic
liquid-cooled channel geometry. Flows circulated through the test
section by a gear pump are modulated using a controller to achieve
sinusoidal flow pulsations with Womersley numbers of 7.45 and
2.36 and an amplitude ratio of 0.75. It is found that the transient
characteristics of the measured velocity profiles are dependent on the
speed of oscillation, in accordance with the analytical solution for
flow in a rectangular channel. A large velocity overshoot is observed
close to the wall at high frequencies, resulting from the interaction
of near-wall viscous stresses and inertial effects of the main fluid
body. The steep velocity gradients at the wall are indicative of
augmented heat transfer, although the local flow reversal may reduce
the upstream temperature difference in heat transfer applications.
While unsteady effects remain evident at the lower frequency, the
annular effect subsides and retreats from the wall. The shear rate at
the wall is increased during the accelerating half-cycle and decreased
during deceleration compared to steady flow, suggesting that the flow
may experience both enhanced and diminished heat transfer during
a single period. Hence, the thickness of the hydrodynamic boundary
layer is reduced for positively moving flow during one half of the
pulsation cycle at the investigated frequencies. It is expected that the
size of the thermal boundary layer is similarly reduced during the
cycle, leading to intervals of heat transfer enhancement.
Abstract: The boundary layer separation and new active flow control of a NACA 0025 airfoil were studied experimentally. This new flow control is sometimes known as a co-flow jet (cfj) airfoil. This paper presents the fluctuating velocity in a wall jet over the co-flow jet airfoil subjected to an adverse pressure gradient and a curved surface. In these results, the fluctuating velocity at the inner part increasing by increased the angle of attack up to 12o and this has due to the jet energized, while the angle of attack 20o has different. The airfoil cord based Reynolds number has 105.
Abstract: Flash flood is occurred in short time rainfall interval:
from 1 hour to 12 hours in small and medium basins. Flash floods
typically have two characteristics: large water flow and big flow
velocity. Flash flood is occurred at hill valley site (strip of lowland of
terrain) in a catchment with large enough distribution area, steep
basin slope, and heavy rainfall. The risk of flash floods is determined
through Gridded Basin Flash Flood Potential Index (GBFFPI). Flash
Flood Potential Index (FFPI) is determined through terrain slope
flash flood index, soil erosion flash flood index, land cover flash
floods index, land use flash flood index, rainfall flash flood index.
Determining GBFFPI, each cell in a map can be considered as outlet
of a water accumulation basin. GBFFPI of the cell is determined as
basin average value of FFPI of the corresponding water accumulation
basin. Based on GIS, a tool is developed to compute GBFFPI using
ArcObjects SDK for .NET. The maps of GBFFPI are built in two
types: GBFFPI including rainfall flash flood index (real time flash
flood warning) or GBFFPI excluding rainfall flash flood index.
GBFFPI Tool can be used to determine a high flash flood potential
site in a large region as quick as possible. The GBFFPI is improved
from conventional FFPI. The advantage of GBFFPI is that GBFFPI is
taking into account the basin response (interaction of cells) and
determines more true flash flood site (strip of lowland of terrain)
while conventional FFPI is taking into account single cell and does
not consider the interaction between cells. The GBFFPI Map of
QuangNam, QuangNgai, DaNang, Hue is built and exported to
Google Earth. The obtained map proves scientific basis of GBFFPI.
Abstract: The construction of most coastal infrastructure developments around the world are usually made considering wave height, current velocities and river discharges; however, little effort has been paid to surveying sediment transport during dredging or the modification to currents outside the ports or marinas during and after the construction. This study shows a complete survey during the construction of one of the largest ports of the Gulf of Mexico. An anchored Acoustic Doppler Current Velocity profiler (ADCP), a towed ADCP and a combination of model outputs were used at the Veracruz port construction in order to describe the hourly sediment transport and current modifications in and out of the new port. Owing to the stability of the system the new port was construction inside Vergara Bay, a low wave energy system with a tidal range of up to 0.40 m. The results show a two-current system pattern within the bay. The north side of the bay has an anticyclonic gyre, while the southern part of the bay shows a cyclonic gyre. Sediment transport trajectories were made every hour using the anchored ADCP, a numerical model and the weekly data obtained from the towed ADCP within the entire bay. The sediment transport trajectories were carefully tracked since the bay is surrounded by coral reef structures which are sensitive to sedimentation rate and water turbidity. The survey shows that during dredging and rock input used to build the wave breaker sediments were locally added (< 2500 m2) and local currents disperse it in less than 4 h. While the river input located in the middle of the bay and the sewer system plant may add more than 10 times this amount during a rainy day or during the tourist season. Finally, the coastal line obtained seasonally with a drone suggests that the southern part of the bay has not been modified by the construction of the new port located in the northern part of the bay, owing to the two subsystem division of the bay.
Abstract: The aim of this study is to examine, through
experimentation in the laboratory, the supercritical flow in the
presence of an obstacle in a rectangular channel. The supercritical
regime in the whole hydraulic channel is achieved by adding a
convergent. We will observe the influence of the obstacle shape and
dimension on the characteristics of the supercritical flow, mainly the
free-surface elevation and the velocity profile. The velocity
measurements have been conducted with the one dimension laser
anemometry technique.
Abstract: Journal bearings used in IC engines are prone to premature
failures and are likely to fail earlier than the rated life due to
highly impulsive and unstable operating conditions and frequent
starts/stops. Vibration signature extraction and wear debris analysis
techniques are prevalent in industry for condition monitoring of
rotary machinery. However, both techniques involve a great deal of
technical expertise, time, and cost. Limited literature is available on
the application of these techniques for fault detection in reciprocating
machinery, due to the complex nature of impact forces that
confounds the extraction of fault signals for vibration-based analysis
and wear prediction. In present study, a simulation model was developed to investigate
the bearing wear behaviour, resulting because of different operating
conditions, to complement the vibration analysis. In current
simulation, the dynamics of the engine was established first, based on
which the hydrodynamic journal bearing forces were evaluated by
numerical solution of the Reynold’s equation. In addition, the
essential outputs of interest in this study, critical to determine wear
rates are the tangential velocity and oil film thickness between the
journals and bearing sleeve, which if not maintained appropriately,
have a detrimental effect on the bearing performance. Archard’s wear prediction model was used in the simulation to
calculate the wear rate of bearings with specific location information
as all determinative parameters were obtained with reference to crank
rotation. Oil film thickness obtained from the model was used as a
criterion to determine if the lubrication is sufficient to prevent contact
between the journal and bearing thus causing accelerated wear. A
limiting value of 1 μm was used as the minimum oil film thickness
needed to prevent contact. The increased wear rate with growing
severity of operating conditions is analogous and comparable to the
rise in amplitude of the squared envelope of the referenced vibration
signals. Thus on one hand, the developed model demonstrated its
capability to explain wear behaviour and on the other hand it also
helps to establish a co-relation between wear based and vibration
based analysis. Therefore, the model provides a cost effective and
quick approach to predict the impending wear in IC engine bearings
under various operating conditions.
Abstract: This paper focuses on the mathematical modeling for
solidification of Al alloy in a cube mold cavity to study the
solidification behavior of casting process. The parametric
investigation of solidification process inside the cavity was
performed by using computational solidification/melting model
coupled with Volume of fluid (VOF) model. The implicit filling
algorithm is used in this study to understand the overall process from
the filling stage to solidification in a model metal casting process.
The model is validated with past studied at same conditions. The
solidification process is analyzed by including the effect of pouring
velocity as well as natural convection from the wall and geometry of
the cavity. These studies show the possibility of various defects
during solidification process.
Abstract: Considering the challenges of short product life cycles
and growing variant diversity, cost minimization and manufacturing
flexibility increasingly gain importance to maintain a competitive
edge in today’s global and dynamic markets. In this context, an
aerodynamic part feeding system for high-speed industrial assembly
applications has been developed at the Institute of Production
Systems and Logistics (IFA), Leibniz Universitaet Hannover. The
aerodynamic part feeding system outperforms conventional systems
with respect to its process safety, reliability, and operating speed. In
this paper, a multi-objective optimisation of the aerodynamic feeding
system regarding the orientation rate, the feeding velocity, and the
required nozzle pressure is presented.
Abstract: Production fluids are transported from the platform to
tankers or process facilities through transfer pipelines. Water being
one of the heavier phases tends to settle at the bottom of pipelines
especially at low flow velocities and this has adverse consequences
for pipeline integrity. On restart after a shutdown, this could result in
corrosion and issues for process equipment, thus the need to have the
heavier liquid dispersed into the flowing lighter fluid. This study
looked at the flow regime of low water cut and low flow velocity oil
and water flow using conductive film thickness probes in a large
diameter 4-inch pipe to obtain oil and water interface height and the
interface structural velocity. A wide range of 0.1–1.0 m/s oil and
water mixture velocities was investigated for 0.5–5% water cut. Two
fluid model predictions were used to compare with the experimental
results.
Abstract: Geological and tectonic framework indicates that
Bangladesh is one of the most seismically active regions in the world.
The Bengal Basin is at the junction of three major interacting plates:
the Indian, Eurasian, and Burma Plates. Besides there are many
active faults within the region, e.g. the large Dauki fault in the north.
The country has experienced a number of destructive earthquakes due
to the movement of these active faults. Current seismic provisions of
Bangladesh are mostly based on earthquake data prior to the 1990.
Given the record of earthquakes post 1990, there is a need to revisit
the design provisions of the code. This paper compares the base shear
demand of three major cities in Bangladesh: Dhaka (the capital city),
Sylhet, and Chittagong for earthquake scenarios of magnitudes
7.0MW, 7.5MW, 8.0MW, and 8.5MW using a stochastic model. In
particular, the stochastic model allows the flexibility to input region
specific parameters such as shear wave velocity profile (that were
developed from Global Crustal Model CRUST2.0) and include the
effects of attenuation as individual components. Effects of soil
amplification were analysed using the Extended Component
Attenuation Model (ECAM). Results show that the estimated base
shear demand is higher in comparison with code provisions leading to
the suggestion of additional seismic design consideration in the study
regions.
Abstract: The understanding of geotechnical characteristics of
near-surface material and the effects of the groundwater is very
important problem in such as site studies. For showing the relations
between seismic data and groundwater, we selected about 25 km2 as
the study area. It has been presented which is a detailed work of
seismic data and groundwater depths of Gokpinar Damp area.
Seismic waves velocity (Vp and Vs) are very important parameters
showing the soil properties. The seismic records were used the
method of the multichannel analysis of surface waves near area of
Gokpinar Damp area. Sixty sites in this area have been investigated
with survey lines about 60 m in length. MASW (Multichannel
analysis of surface wave) method has been used to generate onedimensional
shear wave velocity profile at locations. These shear
wave velocities are used to estimate equivalent shear wave velocity in
the study area at every 2 and 5 m intervals up to a depth of 45 m.
Levels of equivalent shear wave velocity of soil are used the
classified of the study area. After the results of the study, it must be
considered as components of urban planning and building design of
Gokpinar Damp area, Denizli and the application and use of these
results should be required and enforced by municipal authorities.
Abstract: A solar receiver is designed for operation under
extremely uneven heat flux distribution, cyclic weather, and cloud
transient cycle conditions, which can include large thermal stress and
even receiver failure. In this study, the effect of different oil velocity
on convection coefficient factor and impact of wind velocity on local
Nusselt number by Finite Volume Method will be analyzed. This
study is organized to give an overview of the numerical modeling
using a MATLAB software, as an accurate, time efficient and
economical way of analyzing the heat transfer trends over stationary
receiver tube for different Reynolds number. The results reveal when
oil velocity is below 0.33m/s, the value of convection coefficient is
negligible at low temperature. The numerical graphs indicate that
when oil velocity increases up to 1.2 m/s, heat convection coefficient
increases significantly. In fact, a reduction in oil velocity causes a
reduction in heat conduction through the glass envelope. In addition,
the different local Nusselt number is reduced when the wind blows
toward the concave side of the collector and it has a significant effect
on heat losses reduction through the glass envelope.
Abstract: The laser-ultrasonic method is realized for
quantifying the influence of porosity on the local Young’s
modulus of isotropic composite materials. The method is based on
a laser thermooptical method of ultrasound generation combined
with measurement of the phase velocity of longitudinal and shear
acoustic waves in samples. The main advantage of this method
compared with traditional ultrasonic research methods is the
efficient generation of short and powerful probing acoustic pulses
required for reliable testing of ultrasound absorbing and
scattering heterogeneous materials. Using as an example samples
of a metal matrix composite with reinforcing microparticles of
silicon carbide in various concentrations, it is shown that to
provide an effective increase in Young’s modulus with increasing
concentration of microparticles, the porosity of the final sample
should not exceed 2%.
Abstract: The steady flow of a second order fluid through
constricted tube with slip velocity at wall is modeled and analyzed
theoretically. The governing equations are simplified by implying no
slip in radial direction. Based on Karman Pohlhausen procedure
polynomial solution for axial velocity profile is presented.
Expressions for pressure gradient, shear stress, separation and
reattachment points, and radial velocity are also calculated. The
effect of slip and no slip velocity on magnitude velocity, shear stress,
and pressure gradient are discussed and depicted graphically. It is
noted that when Reynolds number increases magnitude velocity of
the fluid decreases in both slip and no slip conditions. It is also found
that the wall shear stress, separation, and reattachment points are
strongly affected by Reynolds number.
Abstract: Exact solution of an unsteady MHD flow of elasticoviscous
fluid through a porous media in a tube of elliptic cross
section under the influence of magnetic field and constant pressure
gradient has been obtained in this paper. Initially, the flow is
generated by a constant pressure gradient. After attaining the steady
state, the pressure gradient is suddenly withdrawn and the resulting
fluid motion in a tube of elliptical cross section by taking into
account of the porosity factor and magnetic parameter of the
bounding surface is investigated. The problem is solved in two-stages
the first stage is a steady motion in tube under the influence of a
constant pressure gradient, the second stage concern with an unsteady
motion. The problem is solved employing separation of variables
technique. The results are expressed in terms of a non-dimensional
porosity parameter, magnetic parameter and elastico-viscosity
parameter, which depends on the Non-Newtonian coefficient. The
flow parameters are found to be identical with that of Newtonian case
as elastic-viscosity parameter, magnetic parameter tends to zero, and
porosity tends to infinity. The numerical results were simulated in
MATLAB software to analyze the effect of Elastico-viscous
parameter, porosity parameter, and magnetic parameter on velocity
profile. Boundary conditions were satisfied. It is seen that the effect
of elastico-viscosity parameter, porosity parameter and magnetic
parameter of the bounding surface has significant effect on the
velocity parameter.
Abstract: This study, tries to suggest a design method based on
displacement using finite difference numerical modeling in
reinforcing soil retaining wall with steel strip. In this case, dynamic
loading characteristics such as duration, frequency, peak ground
acceleration, geometrical characteristics of reinforced soil structure
and type of the site are considered to correct the pseudo static method
and finally introduce the pseudo static coefficient as a function of
seismic performance level and peak ground acceleration. For this
purpose, the influence of dynamic loading characteristics,
reinforcement length, height of reinforced system and type of the site
are investigated on seismic behavior of reinforcing soil retaining wall
with steel strip. Numerical results illustrate that the seismic response
of this type of wall is highly dependent to cumulative absolute
velocity, maximum acceleration, and height and reinforcement length
so that the reinforcement length can be introduced as the main factor
in shape of failure. Considering the loading parameters, geometric parameters of the
wall and type of the site showed that the used method in this study
leads to efficient designs in comparison with other methods, which
are usually based on limit-equilibrium concept. The outputs show the
over-estimation of equilibrium design methods in comparison with
proposed displacement based methods here.
Abstract: In the present study, analysis of heat transfer is carried
out in the slip flow region for the fluid flowing between two parallel
plates by employing the asymmetric heat fluxes at surface of the
plates. The flow is assumed to be hydrodynamically and thermally
fully developed for the analysis. The second order velocity slip and
viscous dissipation effects are considered for the analysis. Closed
form expressions are obtained for the Nusselt number as a function of
Knudsen number and modified Brinkman number. The limiting
condition of the present prediction for Kn = 0, Kn2 = 0, and Brq1 = 0
is considered and found to agree well with other analytical results.
Abstract: This work deals with the problem of MHD mixed
convection in a completely porous and differentially heated vertical
channel. The model of Darcy-Brinkman-Forchheimer with the
Boussinesq approximation is adopted and the governing equations are
solved by the finite volume method. The effects of magnetic field and
buoyancy force intensities are given by the Hartmann and Richardson
numbers respectively, as well as the Joule heating represented by
Eckert number on the velocity and temperature fields, are examined.
The main results show an augmentation of heat transfer rate with the
decrease of Darcy number and the increase of Ri and Ha when Joule
heating is neglected.
Abstract: An experimental study with four different types of bed
conditions was carried out to understand the effect of roughness in
open channel flow at two different Reynolds numbers. The bed
conditions include a smooth surface and three different roughness
conditions, which were generated using sand grains with a median
diameter of 2.46 mm. The three rough conditions include a surface
with distributed roughness, a surface with continuously distributed
roughness and a sand bed with a permeable interface. A commercial
two-component fibre-optic LDA system was used to conduct the
velocity measurements. The variables of interest include the mean
velocity, turbulence intensity, correlation between the streamwise and
the wall normal turbulence, Reynolds shear stress and velocity triple
products. Quadrant decomposition was used to extract the magnitude
of the Reynolds shear stress of the turbulent bursting events. The
effect of roughness was evident throughout the flow depth. The
results show that distributed roughness has the greatest roughness
effect followed by the sand bed and the continuous roughness.
Compared to the smooth bed, the streamwise turbulence intensity
reduces but the vertical turbulence intensity increases at a location
very close to the bed due to the introduction of roughness. Although
the same sand grain is used to create the three different rough bed
conditions, the difference in the turbulence intensity is an indication
that the specific geometry of the roughness has an influence on
turbulence structure.