Abstract: In order to monitor for traffic traversal, sensors can be
deployed to perform collaborative target detection. Such a sensor
network achieves a certain level of detection performance with the
associated costs of deployment and routing protocol. This paper
addresses these two points of sensor deployment and routing algorithm
in the situation where the absolute quantity of sensors or total energy
becomes insufficient. This discussion on the best deployment system
concluded that two kinds of deployments; Normal and Power law
distributions, show 6 and 3 times longer than Random distribution in
the duration of coverage, respectively. The other discussion on routing
algorithm to achieve good performance in each deployment system
was also addressed. This discussion concluded that, in place of the
traditional algorithm, a new algorithm can extend the time of coverage
duration by 4 times in a Normal distribution, and in the circumstance
where every deployed sensor operates as a binary model.
Abstract: Due to their high power-to-weight ratio and low cost, pneumatic actuators are attractive for robotics and automation applications; however, achieving fast and accurate control of their position have been known as a complex control problem. The paper presents a methodology for obtaining controllers that achieve high position accuracy and preserve the closed-loop characteristics over a broad operating range. Experimentation with a number of conventional (or "classical") three-term controllers shows that, as repeated operations accumulate, the characteristics of the pneumatic actuator change requiring frequent re-tuning of the controller parameters (PID gains). Furthermore, three-term controllers are found to perform poorly in recovering the closed-loop system after the application of load or other external disturbances. The key reason for these problems lies in the non-linear exchange of energy inside the cylinder relating, in particular, to the complex friction forces that develop on the piston-wall interface. In order to overcome this problem but still remain within the boundaries of classical control methods, we designed an auto selective classicaql controller so that the system performance would benefit from all three control gains (KP, Kd, Ki) according to system requirements and the characteristics of each type of controller. This challenging experimentation took place for consistent performance in the face of modelling imprecision and disturbances. In the work presented, a selective PID controller is presented for an experimental rig comprising an air cylinder driven by a variable-opening pneumatic valve and equipped with position and pressure sensors. The paper reports on tests carried out to investigate the capability of this specific controller to achieve consistent control performance under, repeated operations and other changes in operating conditions.
Abstract: Most of the collision warning systems currently
available in the automotive market are mainly designed to warn
against imminent rear-end and lane-changing collisions. No collision
warning system is commercially available to warn against imminent
turning collisions at intersections, especially for left-turn collisions
when a driver attempts to make a left-turn at either a signalized or
non-signalized intersection, conflicting with the path of other
approaching vehicles traveling on the opposite-direction traffic
stream. One of the major factors that lead to left-turn collisions is the
human error and misjudgment of the driver of the turning vehicle
when perceiving the speed and acceleration of other vehicles
traveling on the opposite-direction traffic stream; therefore, using a
properly-designed collision warning system will likely reduce, or
even eliminate, this type of collisions by reducing human error. This
paper introduces perceptual framework for a proposed collision
warning system that can detect imminent left-turn collisions at
intersections. The system utilizes a commercially-available detection
sensor (either a radar sensor or a laser detector) to detect approaching
vehicles traveling on the opposite-direction traffic stream and
calculate their speeds and acceleration rates to estimate the time-tocollision
and compare that time to the time required for the turning
vehicle to clear the intersection. When calculating the time required
for the turning vehicle to clear the intersection, consideration is given
to the perception-reaction time of the driver of the turning vehicle,
which is the time required by the driver to perceive the message
given by the warning system and react to it by engaging the throttle.
A regression model was developed to estimate perception-reaction
time based on age and gender of the driver of the host vehicle.
Desired acceleration rate selected by the driver of the turning vehicle,
when making the left-turn movement, is another human factor that is
considered by the system. Another regression model was developed
to estimate the acceleration rate selected by the driver of the turning
vehicle based on driver-s age and gender as well as on the location
and speed of the nearest approaching vehicle along with the
maximum acceleration rate provided by the mechanical
characteristics of the turning vehicle. By comparing time-to-collision
with the time required for the turning vehicle to clear the intersection,
the system displays a message to the driver of the turning vehicle
when departure is safe. An application example is provided to
illustrate the logic algorithm of the proposed system.
Abstract: One of the important steps in a safety and risk management system is the economical evaluation of occupational accident and diseases costs in order to decrease accidents from reoccurring in the workplace. This study proposed a plausible method for calculating occupational accident costs and illnesses in work place. This method design for cost estimation takes into account both the personnel, organizational level as well as the community level especially intended for an Iranian work place. The research indicates that a using systematic method for calculating costs which also provides risk evaluation can help managers to plan correctly the investment in health and safety measures. Using this method is that not only is it comprehensive, easy and practical and could be applied in practice by a manager within a short period of time but it also shows the importance of accident costs as well as calculates the real cost of an accident and illnesses.
Abstract: The paper presents the service learning project titled
DicDucFac (idea-leadership-product), that was planned and
conducted by the team of information sciences students. It was
planned as a workshop dealing with the application of modern social
media (Facebook, YouTube, Gmail) for the purposes of selfpromotion,
free advertising via social networks and marketing own
ideas and/or products in the virtual world. The workshop was
organized for highly-skilled computer literate unemployed youth.
These youth, as final beneficiaries, will be able to apply what they
learned in this workshop to “the real world“, increasing their chances
for employment and self-employment. The results of the project
reveal that the basic, active-learning principles embodied in our
teaching approach allow students to learn more effectively and gain
essential life skills (from computer applications to teamwork) that
can only be learned by doing. It also shows that our students received
the essentials of professional ethics and citizenship through direct,
personal engagement in professional activities and the life of the
community.
Abstract: In this paper, we research the standard 13-point difference schemes for solving the biharmonic equation. Heuristic method is applied to judging the stability of multi-level difference schemes of the biharmonic equation. It is showed that the standard 13-point difference schemes are stable.
Abstract: This article provides a comparative analysis of poetries of diverse nations around the world while largely focusing on Kazakh lyric poetry (Kazakh zhyraulyq oneri). Alongside, it sheds the light to the historical development and contemporary progress path of foremost poetry school located along the Syr Darya coast. Hereby, it-s content and central motives are examined.
Abstract: Hong Kong is one of the regions in the world where Total Fertility Rate (TFR) is very low. In 2001, the TFR dropped until 0.931, which means 1 woman even cannot give birth to one child on average. However, after the reformation of the 'Right of Abode of Hong Kong' in 2001 and the Chinese Central Government loosened the disembarkation procedure of mainland Chinese (mainlander) to enter Hong Kong in 2003; mainlander couples started to cross the border for giving births in Hong Kong. This action raises Hong Kong-s TFR quickly from 0.931 (2001) to 1.094 (2010). Usually, an increasing trend of TFR means a sign of rejuvenation in low-fertility, but in the case of Hong Kong, the increase of TFR does not, rather it generates other population problems. This paper is going to discuss do mainlanders- births help to solve the low-fertility problem in Hong Kong.
Abstract: Categorical data based on description of the
agricultural landscape imposed some mathematical and analytical
limitations. This problem however can be overcome by data
transformation through coding scheme and the use of non-parametric
multivariate approach. The present study describes data
transformation from qualitative to numerical descriptors. In a
collection of 103 random soil samples over a 60 hectare field,
categorical data were obtained from the following variables: levels of
nitrogen, phosphorus, potassium, pH, hue, chroma, value and data on
topography, vegetation type, and the presence of rocks. Categorical
data were coded, and Spearman-s rho correlation was then calculated
using PAST software ver. 1.78 in which Principal Component
Analysis was based. Results revealed successful data transformation,
generating 1030 quantitative descriptors. Visualization based on the
new set of descriptors showed clear differences among sites, and
amount of variation was successfully measured. Possible applications
of data transformation are discussed.
Abstract: A handful of propagation textbooks that discuss radio frequency (RF) propagation models merely list out the models and perhaps discuss them rather briefly; this may well be frustrating for the potential first time modeller who's got no idea on how these models could have been derived. This paper fundamentally provides an overture in modelling the radio channel. Explicitly, for the modelling practice discussed here, signal strength field measurements had to be conducted beforehand (this was done at 469 MHz); to be precise, this paper primarily concerns empirically/statistically modelling the radio channel, and thus provides results obtained from empirically modelling the environments in question. This paper, on the whole, proposes three propagation models, corresponding to three experimented environments. Perceptibly, the models have been derived by way of making the most use of statistical measures. Generally speaking, the first two models were derived via simple linear regression analysis, whereas the third have been originated using multiple regression analysis (with five various predictors). Additionally, as implied by the title of this paper, both indoor and outdoor environments have been experimented; however, (somewhat) two of the environments are neither entirely indoor nor entirely outdoor. The other environment, however, is completely indoor.
Abstract: Many metrics were proposed to evaluate the
characteristics of the analysis and design model of a given product
which in turn help to assess the quality of the product. Function point
metric is a measure of the 'functionality' delivery by the software.
This paper presents an analysis of a set of programs of a project
developed in Cµ through Function Points metric. Function points
are measured for a Data Flow Diagram (DFD) of the case developed
at initial stage. Lines of Codes (LOCs) and possible errors are
calculated with the help of measured Function Points (FPs). The
calculations are performed using suitable established functions.
Calculated LOCs and errors are compared with actual LOCs and
errors found at the time of analysis & design review, implementation
and testing. It has been observed that actual found errors are more
than calculated errors. On the basis of analysis and observations,
authors conclude that function point provides useful insight and helps
to analyze the drawbacks in the development process.
Abstract: Transient Stability is an important issue in power systems planning, operation and extension. The objective of transient stability analysis problem is not satisfied with mere transient instability detection or evaluation and it is most important to complement it by defining fast and efficient control measures in order to ensure system security. This paper presents a new Fuzzy Support Vector Machines (FSVM) to investigate the stability status of power systems and a modified generation rescheduling scheme to bring back the identified unstable cases to a more economical and stable operating point. FSVM improves the traditional SVM (Support Vector Machines) by adding fuzzy membership to each training sample to indicate the degree of membership of this sample to different classes. The preventive control based on economic generator rescheduling avoids the instability of the power systems with minimum change in operating cost under disturbed conditions. Numerical results on the New England 39 bus test system show the effectiveness of the proposed method.
Abstract: Thailand is one of the world-s leaders of rice
producers and exporters. Farmers have to increase the rice cultivation
frequency for serving the national increasing of export-s demand. It
leads to an elimination of rice residues by open burning which is the
quickest and costless management method. The open burning of rice
residue is one of the major causes of air pollutants and greenhouse
gas (GHG) emission. Under ASEAN agreement on trans-boundary
haze, Thailand set the master plan to mitigate air pollutant emission
from open burning of agricultural residues. In this master plan,
residues incorporation is promoted as alternative management
method to open burning. However, the assessment of both options in
term of GHG emission in order to investigate their contribution to
long-term global warming is still scarce or inexistent. In this study, a
method on rice residues assessment was first developed in order to
estimate and compare GHG emissions from rice cultivation under
rice residues open burning and the case with incorporation of the
same amount of rice residues, using 2006 IPCC guidelines for
emission estimation and Life Cycle Analysis technique. The
emission from rice cultivation in different preparing area practice
was also discussed.
Abstract: Hospitals in southern Hualien teamed with the
Hypertension Joint Care Network. Working with the network, the
team provided a special designed health education to the individual
who had been identified as a hypertension patient in the outpatient
department. Some metabolism improvements achieved. This is a
retrospective study by purposively taking 106 patients from a hospital
between 2008 and 2010. Records of before and after education
intervention of the objects was collected and analyzed to see the how
the intervention affected the patients- hypertension control via clinical
parameter monitoring. The results showed that the clinical indicators,
the LDL-C, the cholesterol and the systolic blood pressure were
significantly improved. The study provides evidence for the
effectiveness of the network in controlling hypertension.
Abstract: By analyzing the sources of energy and power
loss in PWM (Pulse Width Modulation) controlled drivers of
water electrolysis cells, it is possible to reduce the power
dissipation and enhance the efficiency of such hydrogen
production units. A PWM controlled power driver is based on
a semiconductor switching element where its power
dissipation might be a remarkable fraction of the total power
demand of an electrolysis system. Power dissipation in a
semiconductor switching element is related to many different
parameters which could be fitted into two main categories:
switching losses and conduction losses. Conduction losses are
directly related to the built, structure and capabilities of a
switching device itself and indeed the conditions in which the
element is handling the switching application such as voltage,
current, temperature and of course the fabrication technology.
On the other hand, switching losses have some other
influencing variables other than the mentioned such as control
system, switching method and power electronics circuitry of
the PWM power driver. By analyzings the characteristics of
recently developed power switching transistors from different
families of Bipolar Junction Transistors (BJT), Metal Oxide
Semiconductor Field Effect Transistors (MOSFET) and
Insulated Gate Bipolar Transistors (IGBT), some
recommendations are made in this paper which are able to
lead to achieve higher hydrogen production efficiency by
utilizing PWM controlled water electrolysis cells.
Abstract: In this paper, perceptions of actors on changes in
crop productivity, quantity and quality of water, and determinants of
their perception are analyzed using descriptive statistics and ordered
logit model. Data collected from 297 Ethiopian farmers and 103
agricultural professionals from December 2009 to January 2010 are
employed. Results show that the majority of the farmers and
professionals recognized decline in water resources, reasoning
climate changes and soil erosion as some of the causes. However,
there is a variation in views on changes in productivity. The
household asset, education level, age and geographical positions are
found to affect farmers- perception on changes in crop productivity.
But, the study underlines that there is no evidence that farmers-
economic status, age, or education level affects recognition of
degradation of water resources. Thus, more focus shall be given on
providing them different coping mechanisms and alternative
resource conserving technologies than educating about the
problems.
Abstract: Space-time block codes (STBC) and spatial multiplexing
(SM) are promising techniques that effectively exploit multipleinput
multiple-output (MIMO) transmission to achieve more reliable
communication and a higher multiplexing rate, respectively. In this
paper, we study a practical design for hybrid scheme with multi-input
multi-output orthogonal frequency division multiplexing (MIMOOFDM)
systems to flexibly maximize the tradeoff between diversity
and multiplexing gains. Unlike the existing STBC and SM designs
which are suitable for the integer multiplexing rate, the proposed
design can achieve arbitrary number of multiplexing rate.
Abstract: Supply chain consists of all stages involved, directly
or indirectly, includes all functions involved in fulfilling a customer
demand. In two stage transportation supply chain problem,
transportation costs are of a significant proportion of final product
costs. It is often crucial for successful decisions making approaches
in two stage supply chain to explicit account for non-linear
transportation costs. In this paper, deterministic demand and finite
supply of products was considered. The optimized distribution level
and the routing structure from the manufacturing plants to the
distribution centres and to the end customers is determined using
developed mathematical model and solved by proposed particle
swarm optimization based genetic algorithm. Numerical analysis of
the case study is carried out to validate the model.
Abstract: The current situation in the eurozone raises a number of topics for discussion and to help in finding an answer to the question of whether a common currency is a more suitable means of coping with the impact of the financial crisis or whether national currencies are better suited to this. The economic situation in the EU is now considerably volatile and, due to problems with the fulfilment of the Maastricht convergence criteria, it is now being considered whether, in their further development, new member states will decide to distance themselves from the euro or will, in an attempt to overcome the crisis, speed up the adoption of the euro. The Czech Republic is one country with little interest in adopting the euro, justified by the fact that a better alternative to dealing with this crisis is an independent monetary policy and its ability to respond flexibly to the economic situation not only in Europe, but around the world. One attribute of the crisis in the Czech Republic and its mitigation is the freely floating exchange rate of the national currency. It is not only the Czech Republic that is attempting to alleviate the impact of the crisis, but also new EU member countries facing fresh questions to which theory have yet to provide wholly satisfactory answers. These questions undoubtedly include the problem of inflation targeting and the choice of appropriate instruments for achieving financial stability. The difficulty lies in the fact that these objectives may be contradictory and may require more than one means of achieving them. In this respect we may assume that membership of the euro zone might not in itself mitigate the development of the recession or protect the nation from future crises. We are of the opinion that the decisive factor in the development of any economy will continue to be the domestic economic policy and the operability of market economic mechanisms. We attempt to document this fact using selected countries as examples, these being the Czech Republic, Poland, Hungary, and Slovakia.
Abstract: In the modern manufacturing systems, the use of
thermal cutting techniques using oxyfuel, plasma and laser have
become indispensable for the shape forming of high quality complex
components; however, the conventional chip removal production
techniques still have its widespread space in the manufacturing
industry. Both these types of machining operations require the
positioning of end effector tool at the edge where the cutting process
commences. This repositioning of the cutting tool in every machining
operation is repeated several times and is termed as non-productive
time or airtime motion. Minimization of this non-productive
machining time plays an important role in mass production with high
speed machining. As, the tool moves from one region to the other by
rapid movement and visits a meticulous region once in the whole
operation, hence the non-productive time can be minimized by
synchronizing the tool movements. In this work, this problem is
being formulated as a general travelling salesman problem (TSP) and
a genetic algorithm approach has been applied to solve the same. For
improving the efficiency of the algorithm, the GA has been
hybridized with a noble special heuristic and simulating annealing
(SA). In the present work a novel heuristic in the combination of GA
has been developed for synchronization of toolpath movements
during repositioning of the tool. A comparative analysis of new Meta
heuristic techniques with simple genetic algorithm has been
performed. The proposed metaheuristic approach shows better
performance than simple genetic algorithm for minimization of nonproductive
toolpath length. Also, the results obtained with the help of
hybrid simulated annealing genetic algorithm (HSAGA) are also
found better than the results using simple genetic algorithm only.