Abstract: Work is focused to the study of unburned carbon in
ash from coal (and wastes) combustion in 8 combustion tests at 3
fluidised-bed power station, at co-combustion of coal and wastes
(also at fluidized bed) and at bench-scale unit simulating coal
combustion in small domestic furnaces. The attention is paid to
unburned carbon contents in bottom ashes and fly ashes at these 8
combustion tests and to morphology of unburned carbons. Specific
surface area of coals, unburned carbons and ashes and the relation of
specific surface area of unburned carbon and the content of volatile
combustibles in coal were studied as well.
Abstract: Fly ash is a significant waste that is released of
thermal power plants and defined as very fine particles that are drifted upward with up taken by the flue gases due to the burning of
used coal [1]. The fly-ash is capable of removing organic
contaminants in consequence of high carbon content, a large surface area per unit volume and contained heavy metals. Therefore, fly ash
is used as an effective coagulant and adsorbent by pelletization [2, 3].
In this study, the possibility of use of fly ash taken from Turkey like low-cost adsorbent for adsorption of zinc ions found in waste
water was investigated. The fly ash taken from Turkey was pelletized with bentonite and molass to evaluate the adsorption capaticity. For
this purpose; analyses such as sieve analysis, XRD, XRF, FTIR and SEM were performed. As a result, it was seen that pellets prepared
from fly ash, bentonite and molass would be used for zinc adsorption.
Abstract: The increased number of automobiles in recent years
has resulted in great demand for fossil fuel. This has led to the
development of automobile by using alternative fuels which include
gaseous fuels, biofuels and vegetables oils as fuel. Energy from
biomass and more specific bio-diesel is one of the opportunities that
could cover the future demand of fossil fuel shortage. Biomass in the
form of cashew nut shell represents a new energy source and
abundant source of energy in India. The bio-fuel is derived from
cashew nut shell oil and its blend with diesel are promising
alternative fuel for diesel engine. In this work the pyrolysis Cashew
Nut Shell Liquid (CNSL)-Diesel Blends (CDB) was used to run the
Direct Injection (DI) diesel engine. The experiments were conducted
with various blends of CNSL and Diesel namely B20, B40, B60, B80
and B100. The results are compared with neat diesel operation. The
brake thermal efficiency was decreased for blends of CNSL and
Diesel except the lower blends of B20. The brake thermal efficiency
of B20 is nearly closer to that of diesel fuel. Also the emission level
of the all CNSL and Diesel blends was increased compared to neat
diesel. The higher viscosity and lower volatility of CNSL leads to
poor mixture formation and hence lower brake thermal efficiency and
higher emission levels. The higher emission level can be reduced by
adding suitable additives and oxygenates with CNSL and Diesel
blends.
Abstract: This paper presents a mathematical model and a
methodology to analyze the losses in transmission expansion
planning (TEP) under uncertainty in demand. The methodology is
based on discrete particle swarm optimization (DPSO). DPSO is a
useful and powerful stochastic evolutionary algorithm to solve the
large-scale, discrete and nonlinear optimization problems like TEP.
The effectiveness of the proposed idea is tested on an actual
transmission network of the Azerbaijan regional electric company,
Iran. The simulation results show that considering the losses even for
transmission expansion planning of a network with low load growth
is caused that operational costs decreases considerably and the
network satisfies the requirement of delivering electric power more
reliable to load centers.
Abstract: Soil washing process with a surfactant solution is a potential technology for the rapid removal of hydrophobic organic compound (HOC) from soil. However, large amount of washed water would be produced during operation and this should be treated effectively by proper methods. The soil washed water for complex contaminated site with HOC and heavy metals might contain high amount of pollutants such as HOC and heavy metals as well as used surfactant. The heavy metals in the soil washed water have toxic effects on microbial activities thus these should be removed from the washed water before proceeding to a biological waste-water treatment system. Moreover, the used surfactant solutions are necessary to be recovered for reducing the soil washing operation cost. In order to simultaneously remove the heavy metals and HOC from soil-washed water, activated carbon (AC) was used in the present study. In an anionic-nonionic surfactant mixed solution, the Cd(II) and phenanthrene (PHE) were effectively removed by adsorption on activated carbon. The removal efficiency for Cd(II) was increased from 0.027 mmol-Cd/g-AC to 0.142 mmol-Cd/g-AC as the mole ratio of SDS increased in the presence of PHE. The adsorptive capacity of PHE was also increased according to the SDS mole ratio due to the decrement of molar solubilization ratios (MSR) for PHE in an anionic-nonionic surfactant mixture. The simultaneous adsorption of HOC and cationic heavy metals using activated carbon could be a useful method for surfactant recovery and the reduction of heavy metal toxicity in a surfactant-enhanced soil washing process.
Abstract: In order to perform on-line measuring and detection
of PD signals, a total solution composing of an HFCT, A/D
converter and a complete software package is proposed. The
software package includes compensation of HFCT contribution,
filtering and noise reduction using wavelet transform and soft
calibration routines. The results have shown good performance and
high accuracy.
Abstract: Influence of octane and benzene on plant cell
ultrastructure and enzymes of basic metabolism, such as nitrogen
assimilation and energy generation have been studied. Different
plants: perennial ryegrass (Lolium perenne) and alfalfa (Medicago
sativa); crops- maize (Zea mays L.) and bean (Phaseolus vulgaris);
shrubs – privet (Ligustrum sempervirens) and trifoliate orange
(Poncirus trifoliate); trees - poplar (Populus deltoides) and white
mulberry (Morus alba L.) were exposed to hydrocarbons of different
concentrations (1, 10 and 100 mM). Destructive changes in bean and
maize leaves cells ultrastructure under the influence of benzene
vapour were revealed at the level of photosynthetic and energy
generation subcellular organells. Different deviations at the level of
subcellular organelles structure and distribution were observed in
alfalfa and ryegrass root cells under the influence of benzene and
octane, absorbed through roots. The level of destructive changes is
concentration dependent. Benzene at low 1 and 10 mM concentration
caused the increase in glutamate dehydrogenase (GDH) activity in
maize roots and leaves and in poplar and mulberry shoots, though to
higher extent in case of lower, 1mM concentration. The induction
was more intensive in plant roots. The highest tested 100mM
concentration of benzene was inhibitory to the enzyme in all plants.
Octane caused induction of GDH in all grassy plants at all tested
concentrations; however the rate of induction decreased parallel to
increase of the hydrocarbon concentration. Octane at concentration 1
mM caused induction of GDH in privet, trifoliate and white mulberry
shoots. The highest, 100mM octane was characterized by inhibitory
effect to GDH activity in all plants. Octane had inductive effect on
malate dehydrogenase in almost all plants and tested concentrations,
indicating the intensification of Trycarboxylic Acid Cycle.
The data could be suggested for elaboration of criteria for plant
selection for phytoremediation of oil hydrocarbons contaminated
soils.
Abstract: The evaluation of residual reliability of large sized
parallel computer interconnection systems is not practicable with
the existing methods. Under such conditions, one must go for
approximation techniques which provide the upper bound and lower
bound on this reliability. In this context, a new approximation method
for providing bounds on residual reliability is proposed here. The
proposed method is well supported by two algorithms for simulation
purpose. The bounds on residual reliability of three different categories
of interconnection topologies are efficiently found by using
the proposed method
Abstract: We have developed a microfluidic device system for the continuous producting of nanoparticles, and we have clarified the relationship between the mixing performance of reactors and the particle size. First, we evaluated the mixing performance of reactors by carring out the Villermaux–Dushman reaction and determined the experimental conditions for producing AgCl nanoparticles. Next, we produced AgCl nanoparticles and evaluated the mixing performance and the particle size. We found that as the mixing performance improves the size of produced particles decreases and the particle size distribution becomes sharper. We produced AgCl nanoparticles with a size of 86 nm using the microfluidic device that had the best mixing performance among the three reactors we tested in this study; the coefficient of variation (Cv) of the size distribution of the produced nanoparticles was 26.1%.
Abstract: Day by day technology increases and problems
associated with this technology also increase. Several researches
were carried out to investigate the deployment of such material safely
in geotechnical engineering in particular and civil engineering in
general. However, different types of waste material have such as
cement duct, fly ash and slag been proven to be suitable in several
applications. In this research cement dust mixed with different
percentages of sand will be used in some civil engineering
application as will be explained later in this paper throughout filed
and laboratory test. The used mixer (waste material with sand) prove
high performance, durability to environmental condition, low cost
and high benefits. At higher cement dust ratio, small cement ratio is
valuable for compressive strength and permeability. Also at small
cement dust ratio higher cement ratio is valuable for compressive
strength.
Abstract: Results are presented from a combined experimental
and modeling study undertaken to understand the effect of fuel spray
angle on soot production in turbulent liquid spray flames. The
experimental work was conducted in a cylindrical laboratory furnace
at fuel spray cone angle of 30º, 45º and 60º. Soot concentrations
inside the combustor are measured by filter paper technique. The soot
concentration is modeled by using the soot particle number density
and the mass density based acetylene concentrations. Soot oxidation
occurred by both hydroxide radicals and oxygen molecules. The
comparison of calculated results against experimental measurements
shows good agreement. Both the numerical and experimental results
show that the peak value of soot and its location in the furnace
depend on fuel spray cone angle. An increase in spray angle enhances
the evaporating rate and peak temperature near the nozzle. Although
peak soot concentration increase with enhance of fuel spray angle but
soot emission from the furnace decreases.
Abstract: Proper orthogonal decomposition (POD) is used to reconstruct spatio-temporal data of a fully developed turbulent channel flow with density variation at Reynolds number of 150, based on the friction velocity and the channel half-width, and Prandtl number of 0.71. To apply POD to the fully developed turbulent channel flow with density variation, the flow field (velocities, density, and temperature) is scaled by the corresponding root mean square values (rms) so that the flow field becomes dimensionless. A five-vector POD problem is solved numerically. The reconstructed second-order moments of velocity, temperature, and density from POD eigenfunctions compare favorably to the original Direct Numerical Simulation (DNS) data.
Abstract: In image processing and visualization, comparing two
bitmapped images needs to be compared from their pixels by matching
pixel-by-pixel. Consequently, it takes a lot of computational time
while the comparison of two vector-based images is significantly
faster. Sometimes these raster graphics images can be approximately
converted into the vector-based images by various techniques. After
conversion, the problem of comparing two raster graphics images
can be reduced to the problem of comparing vector graphics images.
Hence, the problem of comparing pixel-by-pixel can be reduced to
the problem of polynomial comparisons. In computer aided geometric
design (CAGD), the vector graphics images are the composition of
curves and surfaces. Curves are defined by a sequence of control
points and their polynomials. In this paper, the control points will be
considerably used to compare curves. The same curves after relocated
or rotated are treated to be equivalent while two curves after different
scaled are considered to be similar curves. This paper proposed an
algorithm for comparing the polynomial curves by using the control
points for equivalence and similarity. In addition, the geometric
object-oriented database used to keep the curve information has also
been defined in XML format for further used in curve comparisons.
Abstract: In a very simple form a Mobile Agent is an independent piece of code that has mobility and autonomy behavior. One of the main advantages of using Mobile Agent in a network is - it reduces network traffic load. In an, ad hoc network Mobile Agent can be used to protect the network by using agent based IDS or IPS. Besides, to deploy dynamic software in the network or to retrieve information from network nodes Mobile Agent can be useful. But in an ad hoc network the Mobile Agent itself needs some security. Security services should be guaranteed both for Mobile Agent and for Agent Server. In this paper to protect the Mobile Agent and Agent Server in an ad hoc network we have proposed a solution which is based on Threshold Cryptography, a new vibe in the cryptographic world where trust is distributed among multiple nodes in the network.
Abstract: A method and apparatus for noninvasive measurement
of blood glucose concentration based on transilluminated laser beam
via the Index Finger has been reported in this paper. This method
depends on atomic gas (He-Ne) laser operating at 632.8nm
wavelength. During measurement, the index finger is inserted into the
glucose sensing unit, the transilluminated optical signal is converted
into an electrical signal, compared with the reference electrical
signal, and the obtained difference signal is processed by signal
processing unit which presents the results in the form of blood
glucose concentration. This method would enable the monitoring
blood glucose level of the diabetic patient continuously, safely and
noninvasively.
Abstract: Soil stabilization has been widely used to improve
soil strength and durability or to prevent erosion and dust generation.
Generally to reduce problems of clayey soils in engineering work and
to stabilize these soils additional materials are used. The most
common materials are lime, fly ash and cement. Using this materials,
although improve soil property , but in some cases due to financial
problems and the need to use special equipment are limited .One of
the best methods for stabilization clayey soils is neutralization the
clay particles. For this purpose we can use ion exchange materials.
Ion exchange solution like CBR plus can be used for soil
stabilization. One of the most important things in using CBR plus is
determination the amount of this solution for various soils with
different properties. In this study a laboratory experiment is conduct
to evaluate the ion exchange capacity of three soils with various
plasticity index (PI) to determine amount or required CBR plus
solution for soil stabilization.
Abstract: Wind farms (WFs) with high level of penetration are
being established in power systems worldwide more rapidly than
other renewable resources. The Independent System Operator (ISO),
as a policy maker, should propose appropriate places for WF
installation in order to maximize the benefits for the investors. There
is also a possibility of congestion relief using the new installation of
WFs which should be taken into account by the ISO when proposing
the locations for WF installation. In this context, efficient wind farm
(WF) placement method is proposed in order to reduce burdens on
congested lines. Since the wind speed is a random variable and load
forecasts also contain uncertainties, probabilistic approaches are used
for this type of study. AC probabilistic optimal power flow (P-OPF)
is formulated and solved using Monte Carlo Simulations (MCS). In
order to reduce computation time, point estimate methods (PEM) are
introduced as efficient alternative for time-demanding MCS.
Subsequently, WF optimal placement is determined using generation
shift distribution factors (GSDF) considering a new parameter
entitled, wind availability factor (WAF). In order to obtain more
realistic results, N-1 contingency analysis is employed to find the
optimal size of WF, by means of line outage distribution factors
(LODF). The IEEE 30-bus test system is used to show and compare
the accuracy of proposed methodology.
Abstract: Tourism and coastal lines are the business sectors
since centuries especially in the European Nations and Albania is one
such spots. However, in recent decades tourism is experienced as
vulnerability of the surrounding ecological conditions of air, soil,
water, land and the communities that are dependant and sharing the
ecosystem among flora and fauna. Experts opine that apart from the
maintenance of near-originality of ecological biodiversity the tourism
rather known as ecotourism an indigenous socio-cultural
maintenance of indigenous/traditional knowledge of the local people
must be well cared in order to sustain on sustainable grounds. As a
general tendency, growth of tourism has been affected by the deterioration in the economic conditions on one aspect and unsustainable ecological areas affected since human interventions
earlier to this has negative impact on futuristic tourist spots. However, tourism in Albania as of now is 11% of GDP and coastal regions accounting to 2-4%. An amicable Mediterranean
climate with 300 sunny days similar parameters of Greece and Spain
throws up sustainable ecotourism in future decades provided public services namely, transportation, road safety, lodging, food
availability, recreational regiments, banking accessibility are as per
the World Tourism Organizations- protocols. Thus as of Albanian
situation, classification of ecotourism activities to safe-guard the localities with its maintenance of ecological land, water and climate
has become a paramount importance with a wanting and satisfactory options through harnessing human energy for profit and fitness of
ecological flora and fauna. A check on anthropogenic wastes and
their safer utilizations inclusive of agricultural and industrial
operations in line with Lalzi Bay Coastal Line are of utmost importance for the reason that the Adriatic Sea Coast is the one long
stretch of Albanian Lifeline. The present work is based on the methodology of the sustainable management of the same issue.
Abstract: In this paper, a new efficient method for load balancing in low voltage distribution systems is presented. The proposed method introduces an improved Leap-frog method for optimization. The proposed objective function includes the difference between three phase currents, as well as two other terms to provide the integer property of the variables; where the latter are the status of the connection of loads to different phases. Afterwards, a new algorithm is supplemented to undertake the integer values for the load connection status. Finally, the method is applied to different parts of Tabriz low voltage network, where the results have shown the good performance of the proposed method.
Abstract: In this study, inhibition of Microcystis aeruginosa by
antialgal alleochemical gramine, was studied by analyzing algal
metabolic activity (represented by esterase and total dehydrogenase
activities) and cell ultrastructure (showing morphological and
ultrastructure alterations using transmission electron microscopy and
DNA ladder analysis). After gramine exposure, esterase and total
dehydrogenase activities were increased firstly but decreased later. In
contrast with the controls, the cells exposed to gramine showed
apparent ultrastructure alterations with thylakoids in breakage,
phycobilins in decrease, lipid and cyanophycin granules abundant
firstly but dissolved afterwards, DNA in fragementation. The
occurrence of increase of metabolic activity and specific granules
reflected that the resistance of cellular response to gramine was
initiated. DNA fragementation associated with the increase of
metabolic activity and specific granules hinted that gramine caused M.
aeruginosa cells to initiate some morphotype of programmed cell
death.