Abstract: This paper presents a study on the effect of
second-order slip on forced convection through a long isoflux heated
or cooled planar microchannel. The fully developed solutions of flow
and thermal fields are analytically obtained on the basis of the
second-order Maxwell-Burnett slip and local heat flux boundary
conditions. Results reveal that when the average flow velocity
increases or the wall heat flux amount decreases, the role of thermal
creep becomes more insignificant, while the effect of second-order slip
becomes larger. The second-order term in the Deissler slip boundary
condition is found to contribute a positive velocity slip and then to lead
to a lower pressure drop as well as a lower temperature rise for the
heated-wall case or to a higher temperature rise for the cooled-wall
case. These findings are contrary to predictions made by the
Karniadakis slip model.
Abstract: In this study, the static behavior of super elliptical Winkler plate is analyzed by applying the double side approach method. The lack of information about super elliptical Winkler plates is the motivation of this study and we use the double side approach method to solve this problem because of its superior ability on efficiently treating problems with complex boundary shape. The double side approach method has the advantages of high accuracy, easy calculation procedure and less calculation load required. Most important of all, it can give the error bound of the approximate solution. The numerical results not only show that the double side approach method works well on this problem but also provide us the knowledge of static behavior of super elliptical Winkler plate in practical use.
Abstract: Today automobile and aerospace industries realise Laser Beam Welding for a clean and non contact source of heating and fusion for joining of sheets. The welding performance is mainly based on by the laser welding parameters. Some concepts related to Artificial Neural Networks and how can be applied to model weld bead geometry and mechanical properties in terms of equipment parameters are reported in order to evaluate the accuracy and compare it with traditional modeling schemes. This review reveals the output features of Titanium and Aluminium weld bead geometry and mechanical properties such as ultimate tensile strength, yield strength, elongation and reduction of the area of the weld using Artificial Neural Network.
Abstract: In this paper, the structural genetic algorithm is used to optimize the neural network to control the joint movements of robotic arm. The robotic arm has also been modeled in 3D and simulated in real-time in MATLAB. It is found that Neural Networks provide a simple and effective way to control the robot tasks. Computer simulation examples are given to illustrate the significance of this method. By combining Genetic Algorithm optimization method and Neural Networks for the given robotic arm with 5 D.O.F. the obtained the results shown that the base joint movements overshooting time without controller was about 0.5 seconds, while with Neural Network controller (optimized with Genetic Algorithm) was about 0.2 seconds, and the population size of 150 gave best results.
Abstract: Numerical study is performed to investigate the
temperature distribution in an annular diffuser fitted with helical tape
hub. Different pitches (Y = 20 mm, and Y = 30 mm) for the helical
tape are studied with different heights (H = 20 mm, 22 mm, and 24
mm) to be compared. The geometry of the annular diffuser and the
inlet condition for both hub arrangements are kept constant. The
result obtains that using helical tape insert with different pitches and
different heights will force the temperature to distribute in a helical
direction; however the use of helical tape hub with height (H = 22
mm) for both pitches enhance the temperature distribution in a good
manner.
Abstract: The influence of twist arrangement on the temperature
distribution in an annular diffuser fitted with twisted rectangular hub
is investigated. Different pitches (Y = 120 mm, 100 mm, 80 mm, and
60 mm) for the twist arrangements are simulated to be compared. The
geometry of the annular diffuser and the inlet condition for the hub
arrangements are kept constant. The result reveals that using twisted
rectangular hub insert with different pitches will force the
temperature to distribute in a circular direction. However,
temperature distribution will be enhanced with the length pitch
increases.
Abstract: Flow around a flat tube is studied numerically. Reynolds number is defined base on equivalent circular tube and it is varied in range of 100 to 300. Equations are solved by using finite volume method and results are presented in form of drag and lift coefficient. Results show that drag coefficient of flat tube is up to 66% lower than circular tube with equivalent diameter. In addition, by increasing l/D from 1 to 2, the drag coefficient of flat tube is decreased about 14-27%.
Abstract: During the last decade ultrafine grained (UFG) and nano-structured (NS) materials have experienced a rapid development. In this research work finite element analysis has been carried out to investigate the plastic strain distribution in equal channel angular process (ECAP). The magnitudes of Standard deviation (S. D.) and inhomogeneity index (Ci) were compared for different ECAP passes. Verification of a three-dimensional finite element model was performed with experimental tests. Finally the mechanical property including impact energy of ultrafine grained pure commercially pure Aluminum produced by severe plastic deformation method has been examined. For this aim, equal channel angular pressing die with the channel angle, outer corner angle and channel diameter of 90°, 20° and 20mm had been designed and manufactured. Commercial pure Aluminum billets were ECAPed up to four passes by route BC at the ambient temperature. The results indicated that there is a great improvement at the hardness measurement, yield strength and ultimate tensile strength after ECAP process. It is found that the magnitudes of HV reach 67HV from 21HV after the final stage of process. Also, about 330% and 285% enhancement at the YS and UTS values have been obtained after the fourth pass as compared to the as-received conditions, respectively. On the other hand, the elongation to failure and impact energy have been reduced by 23% and 50% after imposing four passes of ECAP process, respectively.
Abstract: Numerical investigation of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann methods at different Reynolds numbers. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations, streamlines and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The Reynolds numbers affected the physical quantities.