Abstract: We present a novel scheme to evaluate sinusoidal functions with low complexity and high precision using cubic spline interpolation. To this end, two different approaches are proposed to find the interpolating polynomial of sin(x) within the range [- π , π]. The first one deals with only a single data point while the other with two to keep the realization cost as low as possible. An approximation error optimization technique for cubic spline interpolation is introduced next and is shown to increase the interpolator accuracy without increasing complexity of the associated hardware. The architectures for the proposed approaches are also developed, which exhibit flexibility of implementation with low power requirement.
Abstract: The crystalline quality of the AlGaN/GaN high electron mobility transistor (HEMT) structure grown on a 200 mm silicon substrate has been investigated using UV-visible micro- Raman scattering and photoluminescence (PL). The visible Raman scattering probes the whole nitride stack with the Si substrate and shows the presence of a small component of residual in-plane stress in the thick GaN buffer resulting from a wafer bowing, while the UV micro-Raman indicates a tensile interfacial stress induced at the top GaN/AlGaN/AlN layers. PL shows a good crystal quality GaN channel where the yellow band intensity is very low compared to that of the near-band-edge transition. The uniformity of this sample is shown by measurements from several points across the epiwafer.
Abstract: In this empirical research, how marketing managers evaluate their firms- performances and decide to make innovation is examined. They use some standards which are past performance of the firm, target performance of the firm, competitor performance, and average performance of the industry to compare and evaluate the firms- performances. It is hypothesized that marketing managers and owners of the firm compare the firms- current performance with these four standards at the same time to decide when to make innovation relating to any aspects of the firm, either management style or products. Relationship between the comparison of the firm-s performance with these standards and innovation are searched in the same regression model. The results of the regression analysis are discussed and some recommendations are made for future studies and applicants.
Abstract: The objectives of this research are to produce
prototype coconut oil based solvent offset printing inks and to
analyze a basic quality of printing work derived from coconut oil
based solvent offset printing inks, by mean of bringing coconut oil
for producing varnish and bringing such varnish to produce black
offset printing inks. Then, analysis of qualities i.e. CIELAB value,
density value, and dot gain value of printing work from coconut oil
based solvent offset printing inks which printed on gloss-coated
woodfree paper weighs 130 grams were done. The research result of
coconut oil based solvent offset printing inks indicated that the
suitable varnish formulation is using 51% of coconut oil, 36% of
phenolic resin, and 14% of solvent oil 14%, while the result of
producing black offset ink displayed that the suitable formula of
printing ink is using varnish mixed with 20% of coconut oil, and the
analyzing printing work of coconut oil based solvent offset printing
inks which printed on paper, the results were as follows: CIELAB
value of black offset printing ink is at L* = 31.90, a* = 0.27, and b* =
1.86, density value is at 1.27 and dot gain value was high at mid tone
area of image area.
Abstract: The National Agricultural Biotechnology Information
Center (NABIC) plays a leading role in the biotechnology information
database for agricultural plants in Korea. Since 2002, we have
concentrated on functional genomics of major crops, building an
integrated biotechnology database for agro-biotech information that
focuses on bioinformatics of major agricultural resources such as rice,
Chinese cabbage, and microorganisms. In the NABIC,
integration-based biotechnology database provides useful information
through a user-friendly web interface that allows analysis of genome
infrastructure, multiple plants, microbial resources, and living
modified organisms.
Abstract: Falling has been one of the major concerns and threats
to the independence of the elderly in their daily lives. With the
worldwide significant growth of the aging population, it is essential
to have a promising solution of fall detection which is able to operate
at high accuracy in real-time and supports large scale implementation
using multiple cameras. Field Programmable Gate Array (FPGA) is a
highly promising tool to be used as a hardware accelerator in many
emerging embedded vision based system. Thus, it is the main
objective of this paper to present an FPGA-based solution of visual
based fall detection to meet stringent real-time requirements with
high accuracy. The hardware architecture of visual based fall
detection which utilizes the pixel locality to reduce memory accesses
is proposed. By exploiting the parallel and pipeline architecture of
FPGA, our hardware implementation of visual based fall detection
using FGPA is able to achieve a performance of 60fps for a series of
video analytical functions at VGA resolutions (640x480). The results
of this work show that FPGA has great potentials and impacts in
enabling large scale vision system in the future healthcare industry
due to its flexibility and scalability.
Abstract: Research in quantum computation is looking for the consequences of having information encoding, processing and communication exploit the laws of quantum physics, i.e. the laws which govern the ultimate knowledge that we have, today, of the foreign world of elementary particles, as described by quantum mechanics. This paper starts with a short survey of the principles which underlie quantum computing, and of some of the major breakthroughs brought by the first ten to fifteen years of research in this domain; quantum algorithms and quantum teleportation are very biefly presented. The next sections are devoted to one among the many directions of current research in the quantum computation paradigm, namely quantum programming languages and their semantics. A few other hot topics and open problems in quantum information processing and communication are mentionned in few words in the concluding remarks, the most difficult of them being the physical implementation of a quantum computer. The interested reader will find a list of useful references at the end of the paper.
Abstract: In this manuscript, a wavelet-based blind
watermarking scheme has been proposed as a means to provide
security to authenticity of a fingerprint. The information used for
identification or verification of a fingerprint mainly lies in its
minutiae. By robust watermarking of the minutiae in the fingerprint
image itself, the useful information can be extracted accurately even
if the fingerprint is severely degraded. The minutiae are converted in
a binary watermark and embedding these watermarks in the detail
regions increases the robustness of watermarking, at little to no
additional impact on image quality. It has been experimentally shown
that when the minutiae is embedded into wavelet detail coefficients
of a fingerprint image in spread spectrum fashion using a
pseudorandom sequence, the robustness is observed to have a
proportional response while perceptual invisibility has an inversely
proportional response to amplification factor “K". The DWT-based
technique has been found to be very robust against noises,
geometrical distortions filtering and JPEG compression attacks and is
also found to give remarkably better performance than DCT-based
technique in terms of correlation coefficient and number of erroneous
minutiae.
Abstract: An Optimal Power Flow based on Improved Particle
Swarm Optimization (OPF-IPSO) with Generator Capability Curve
Constraint is used by NN-OPF as a reference to get pattern of
generator scheduling. There are three stages in Designing NN-OPF.
The first stage is design of OPF-IPSO with generator capability curve
constraint. The second stage is clustering load to specific range and
calculating its index. The third stage is training NN-OPF using
constructive back propagation method. In training process total load
and load index used as input, and pattern of generator scheduling
used as output. Data used in this paper is power system of Java-Bali.
Software used in this simulation is MATLAB.
Abstract: This paper presents nonlinear elastic dynamic analysis
of 3-D semi-rigid steel frames including geometric and connection
nonlinearities. The geometric nonlinearity is considered by using
stability functions and updating geometric stiffness matrix. The
nonlinear behavior of the steel beam-to-column connection is
considered by using a zero-length independent connection element
comprising of six translational and rotational springs. The nonlinear
dynamic equilibrium equations are solved by the Newmark numerical
integration method. The nonlinear time-history analysis results are
compared with those of previous studies and commercial SAP2000
software to verify the accuracy and efficiency of the proposed
procedure.
Abstract: This paper presents an application of level sets for the segmentation of abdominal and thoracic aortic aneurysms in CTA
datasets. An important challenge in reliably detecting aortic is the
need to overcome problems associated with intensity
inhomogeneities. Level sets are part of an important class of methods
that utilize partial differential equations (PDEs) and have been extensively applied in image segmentation. A kernel function in the
level set formulation aids the suppression of noise in the extracted
regions of interest and then guides the motion of the evolving contour
for the detection of weak boundaries. The speed of curve evolution
has been significantly improved with a resulting decrease in segmentation time compared with previous implementations of level
sets, and are shown to be more effective than other approaches in
coping with intensity inhomogeneities. We have applied the Courant
Friedrichs Levy (CFL) condition as stability criterion for our algorithm.
Abstract: The most severe damage of the turbine rotor is its
distortion. The rotor straightening process must lead, at the first
stage, to removal of the stresses from the material by annealing and
next, to straightening of the plastic distortion without leaving any
stress by hot spotting. The straightening method does not produce
stress accumulations and the heating technique, developed
specifically for solid forged rotors and disks, enables to avoid local
overheating and structural changes in the material. This process also
does not leave stresses in the shaft material. An experimental study
of hot spotting is carried out on a large turbine rotor and some of the
most important effective parameters that must be considered on
annealing and hot spotting processes are investigated in this paper.
Abstract: The organic farmers use wider range of crop varieties than the conventional farming. Bread wheat is the most favorite and the most common food crop. The organic bread wheat is usually of worse technological quality. Therefore, it is supposed to be an attractive alternative to the hulled wheat species (einkorn, emmer wheat and spelt). Twenty-five hulled bread wheat varieties and control bread wheat ones were grown on the certified organic parcel in České Budějovice (the Czech Republic) between 2009 and 2012. Their baking quality was measured and evaluated with standard methods, and in accordance with ICC. The results have shown that the grain of hulled wheat varieties contain a lot of proteins in grains (up to 18 percent); even the organic hulled bread wheat varieties are characterized by such good baking quality. Einkorn and emmer wheat are of worse technological quality of proteins (low values of gluten index and Zeleny test), which is a disadvantage of these two wheat species. On the other hand, spelt wheat is of better technological quality and is similar to the control bread wheat varieties. Mixtures consisting of bread wheat, among others, are considered good alternatives; they may contribute to wider range of use of the hulled wheat species. It is one of the possibilities which may increase the proportion of proteins in bread wheat grains; the nutrition-rich hulled wheat grains may be also used in such way at the same time.
Abstract: The ever growing sentiment of environmentalism across the globe has made many people think on the green lines. But most of such ideas halt short of implementation because of the short term economic viability issues with the concept of going green. In this paper we have tried to amalgamate the green concept with social entrepreneurship for solving a variety of issues faced by the society today. In addition the paper also tries to ensure that the short term economic viability does not act as a deterrent. The paper comes up three sustainable models of social entrepreneurship which tackle a wide assortment of issues such as nutrition problem, land problems, pollution problems and employment problems. The models described fall under the following heads: - Spirulina cultivation: The model addresses nutrition, land and employment issues. It deals with cultivation of a blue green alga called Spirulina which can be used as a very nutritious food. Also, the implementation of this model would bring forth employment to the poor people of the area. - Biocomposites: The model comes up with various avenues in which biocomposites can be used in an economically sustainable manner. This model deals with the environmental concerns and addresses the depletion of natural resources. - Packaging material from empty fruit bunches (EFB) of oil palm: This one deals with air and land pollution. It is intended to be a substitute for packaging materials made from Styrofoam and plastics which are non-biodegradable. It takes care of the biodegradability and land pollution issues. It also reduces air pollution as the empty fruit bunches are not incinerated. All the three models are sustainable and do not deplete the natural resources any further. This paper explains each of the models in detail and deals with the operational/manufacturing procedures and cost analysis while also throwing light on the benefits derived and sustainability aspects.
Abstract: The research object was apple-black currant
marmalade candies. Experiments were carried out at the Faculty of
Food Technology of the Latvia University of Agriculture. An active
packaging in combination with modified atmosphere (MAP, CO2
100%) was examined and compared with traditional packaging in air
ambiance. Polymer Multibarrier 60 and paper bags were used.
Influence of iron based oxygen absorber in sachets of 500 cc
obtained from Mitsubishi Gas Chemical Europe Ageless® was tested
on the quality during the shelf of marmalade. Samples of 80±5 g
were packaged in polymer pouches (110 mm x 110 mm),
hermetically sealed by MULTIVAC C300 vacuum chamber machine,
and stored in room temperature +20.0±1.0 °C. The physiochemical
properties – weight losses, moisture content, hardness, aw, pH, colour,
changes of atmosphere content (CO2 and O2) in headspace of packs,
and microbial conditions were analysed before packaging and in the
1st, 3rd , 5th, 8th, 11th and 15th weeks of storage.
Abstract: Skin color based tracking techniques often assume a
static skin color model obtained either from an offline set of library
images or the first few frames of a video stream. These models
can show a weak performance in presence of changing lighting or
imaging conditions. We propose an adaptive skin color model based
on the Gaussian mixture model to handle the changing conditions.
Initial estimation of the number and weights of skin color clusters
are obtained using a modified form of the general Expectation
maximization algorithm, The model adapts to changes in imaging
conditions and refines the model parameters dynamically using spatial
and temporal constraints. Experimental results show that the method
can be used in effectively tracking of hand and face regions.
Abstract: A supervisory scheme is proposed that implements Stepwise Safe Switching Logic. The functionality of the supervisory scheme is organized in the following eight functional units: Step- Wise Safe Switching unit, Common controllers design unit, Experimentation unit, Simulation unit, Identification unit, Trajectory cruise unit, Operating points unit and Expert system unit. The supervisory scheme orchestrates both the off-line preparative actions, as well as the on-line actions that implement the Stepwise Safe Switching Logic. The proposed scheme is a generic tool, that may be easily applied for a variety of industrial control processes and may be implemented as an automation software system, with the use of a high level programming environment, like Matlab.
Abstract: Content-based music retrieval generally involves analyzing, searching and retrieving music based on low or high level features of a song which normally used to represent artists, songs or music genre. Identifying them would normally involve feature extraction and classification tasks. Theoretically the greater features analyzed, the better the classification accuracy can be achieved but with longer execution time. Technique to select significant features is important as it will reduce dimensions of feature used in classification and contributes to the accuracy. Artificial Immune System (AIS) approach will be investigated and applied in the classification task. Bio-inspired audio content-based retrieval framework (B-ACRF) is proposed at the end of this paper where it embraces issues that need further consideration in music retrieval performances.
Abstract: This research aims to create a model for analysis of student motivation behavior on e-Learning based on association rule mining techniques in case of the Information Technology for Communication and Learning Course at Suan Sunandha Rajabhat University. The model was created under association rules, one of the data mining techniques with minimum confidence. The results showed that the student motivation behavior model by using association rule technique can indicate the important variables that influence the student motivation behavior on e-Learning.
Abstract: In this paper, a novel contrast enhancement technique
for contrast enhancement of a low-contrast satellite image has been
proposed based on the singular value decomposition (SVD) and
discrete cosine transform (DCT). The singular value matrix
represents the intensity information of the given image and any
change on the singular values change the intensity of the input image.
The proposed technique converts the image into the SVD-DCT
domain and after normalizing the singular value matrix; the enhanced
image is reconstructed by using inverse DCT. The visual and
quantitative results suggest that the proposed SVD-DCT method
clearly shows the increased efficiency and flexibility of the proposed
method over the exiting methods such as Linear Contrast Stretching
technique, GHE technique, DWT-SVD technique, DWT technique,
Decorrelation Stretching technique, Gamma Correction method
based techniques.