Abstract: This paper focuses on a critical component of the situational awareness (SA), the control of autonomous vertical flight for tactical unmanned aerial vehicle (TUAV). With the SA strategy, we proposed a two stage flight control procedure using two autonomous control subsystems to address the dynamics variation and performance requirement difference in initial and final stages of flight trajectory for an unmanned helicopter model with coaxial rotor and ducted fan configuration. This control strategy for chosen model of TUAV has been verified by simulation of hovering maneuvers using software package Simulink and demonstrated good performance for fast stabilization of engines in hovering, consequently, fast SA with economy in energy can be asserted during search-and-rescue operations.
Abstract: The steady mixed convection boundary layer flow from
a vertical cone in a porous medium filled with a nanofluid is
numerically investigated using different types of nanoparticles as Cu
(copper), Al2O3 (alumina) and TiO2 (titania). The boundary value
problem is solved by using the shooting technique by reducing it
into an ordinary differential equation. Results of interest for the local
Nusselt number with various values of the constant mixed convection
parameter and nanoparticle volume fraction parameter are evaluated.
It is found that dual solutions exist for a certain range of mixed
convection parameter.
Abstract: A dead leg is a typical subsea production system
component. CFD is required to model heat transfer within the dead
leg. Unfortunately its solution is time demanding and thus not
suitable for fast prediction or repeated simulations. Therefore there is
a need to create a thermal FEA model, mimicking the heat flows and
temperatures seen in CFD cool down simulations.
This paper describes the conventional way of tuning and a new
automated way using parametric model order reduction (PMOR)
together with an optimization algorithm. The tuned FE analyses
replicate the steady state CFD parameters within a maximum error in
heat flow of 6 % and 3 % using manual and PMOR method
respectively. During cool down, the relative error of the tuned FEA
models with respect to temperature is below 5% comparing to the
CFD. In addition, the PMOR method obtained the correct FEA setup
five times faster than the manually tuned FEA.
Abstract: The cup method is applied for the measurement of water vapor transport properties of porous materials worldwide. However, in practical applications the experimental results are often used without taking into account some secondary effects which can play an important role under specific conditions. In this paper, the effect of temperature on water vapor transport properties of cellular concrete is studied, together with the influence of sample thickness. At first, the bulk density, matrix density, total open porosity and sorption and desorption isotherms are measured for material characterization purposes. Then, the steady state cup method is used for determination of water vapor transport properties, whereas the measurements are performed at several temperatures and for three different sample thicknesses.
Abstract: Software project effort estimation is frequently seen
as complex and expensive for individual software engineers.
Software production is in a crisis. It suffers from excessive costs.
Software production is often out of control. It has been suggested that
software production is out of control because we do not measure.
You cannot control what you cannot measure. During last decade, a
number of researches on cost estimation have been conducted. The
metric-set selection has a vital role in software cost estimation
studies; its importance has been ignored especially in neural network
based studies. In this study we have explored the reasons of those
disappointing results and implemented different neural network
models using augmented new metrics. The results obtained are
compared with previous studies using traditional metrics. To be able
to make comparisons, two types of data have been used. The first
part of the data is taken from the Constructive Cost Model
(COCOMO'81) which is commonly used in previous studies and the
second part is collected according to new metrics in a leading
international company in Turkey. The accuracy of the selected
metrics and the data samples are verified using statistical techniques.
The model presented here is based on Multi-Layer Perceptron
(MLP). Another difficulty associated with the cost estimation studies
is the fact that the data collection requires time and care. To make a
more thorough use of the samples collected, k-fold, cross validation
method is also implemented. It is concluded that, as long as an
accurate and quantifiable set of metrics are defined and measured
correctly, neural networks can be applied in software cost estimation
studies with success
Abstract: There are various overlay structures that provide
efficient and scalable solutions for point and range query in a peer-topeer
network. Overlay structure based on m-Binary Search Tree
(BST) is one such popular technique. It deals with the division of the
tree into different key intervals and then assigning the key intervals to
a BST. The popularity of the BST makes this overlay structure
vulnerable to different kinds of attacks. Here we present four such
possible attacks namely index poisoning attack, eclipse attack,
pollution attack and syn flooding attack. The functionality of BST is
affected by these attacks. We also provide different security
techniques that can be applied against these attacks.
Abstract: The influence of eccentric discharge of stored solids in
squat silos has been highly valued by many researchers. However,
calculation method of lateral pressure under eccentric flowing still
needs to be deeply studied. In particular, the lateral pressure
distribution on vertical wall could not be accurately recognized
mainly because of its asymmetry. In order to build mechanical model
of lateral pressure, flow channel and flow pattern of stored solids in
squat silo are studied. In this passage, based on Janssen-s theory, the
method for calculating lateral static pressure in squat silos after
eccentric discharge is proposed. Calculative formulae are deduced for
each of three possible cases. This method is also focusing on
unsymmetrical distribution characteristic of silo wall normal
pressure. Finite element model is used to analysis and compare the
results of lateral pressure and the numerical results illustrate the
practicability of the theoretical method.
Abstract: This paper considers various channels of gammaquantum
generation via an ultra-short high-power laser pulse
interaction with different targets.We analyse the possibilities to create
a pulsed gamma-radiation source using laser triggering of some
nuclear reactions and isomer targets. It is shown that sub-MeV
monochromatic short pulse of gamma-radiation can be obtained with
pulse energy of sub-mJ level from isomer target irradiated by intense
laser pulse. For nuclear reaction channel in light- atom materials, it is
shown that sub-PW laser pulse gives rise to formation about million
gamma-photons of multi-MeV energy.
Abstract: The security of their network remains the priorities of almost all companies. Existing security systems have shown their limit; thus a new type of security systems was born: honeypots. Honeypots are defined as programs or intended servers which have to attract pirates to study theirs behaviours. It is in this context that the leurre.com project of gathering about twenty platforms was born. This article aims to specify a model of honeypots attack. Our model describes, on a given platform, the evolution of attacks according to theirs hours. Afterward, we show the most attacked services by the studies of attacks on the various ports. It is advisable to note that this article was elaborated within the framework of the research projects on honeyspots within the LABTIC (Laboratory of Information Technologies and Communication).
Abstract: In this paper we present a novel approach for face image coding. The proposed method makes a use of the features of video encoders like motion prediction. At first encoder selects appropriate prototype from the database and warps it according to features of encoding face. Warped prototype is placed as first I frame. Encoding face is placed as second frame as P frame type. Information about features positions, color change, selected prototype and data flow of P frame will be sent to decoder. The condition is both encoder and decoder own the same database of prototypes. We have run experiment with H.264 video encoder and obtained results were compared to results achieved by JPEG and JPEG2000. Obtained results show that our approach is able to achieve 3 times lower bitrate and two times higher PSNR in comparison with JPEG. According to comparison with JPEG2000 the bitrate was very similar, but subjective quality achieved by proposed method is better.
Abstract: The incorporation of renewable energy sources for the sustainable electricity production is undertaking a more prominent role in electric power systems. Thus, it will be an indispensable incident that the characteristics of future power networks, their prospective stability for instance, get influenced by the imposed features of sustainable energy sources. One of the distinctive attributes of the sustainable energy sources is exhibiting the stochastic behavior. This paper investigates the impacts of this stochastic behavior on the small disturbance rotor angle stability in the upcoming electric power networks. Considering the various types of renewable energy sources and the vast variety of system configurations, the sensitivity analysis can be an efficient breakthrough towards generalizing the effects of new energy sources on the concept of stability. In this paper, the definition of small disturbance angle stability for future power systems and the iterative-stochastic way of its analysis are presented. Also, the effects of system parameters on this type of stability are described by performing a sensitivity analysis for an electric power test system.
Abstract: The stereophotogrammetry modality is gaining more widespread use in the clinical setting. Registration and visualization of this data, in conjunction with conventional 3D volumetric image modalities, provides virtual human data with textured soft tissue and internal anatomical and structural information. In this investigation computed tomography (CT) and stereophotogrammetry data is acquired from 4 anatomical phantoms and registered using the trimmed iterative closest point (TrICP) algorithm. This paper fully addresses the issue of imaging artifacts around the stereophotogrammetry surface edge using the registered CT data as a reference. Several iterative algorithms are implemented to automatically identify and remove stereophotogrammetry surface edge outliers, improving the overall visualization of the combined stereophotogrammetry and CT data. This paper shows that outliers at the surface edge of stereophotogrammetry data can be successfully removed automatically.
Abstract: Trace element speciation of an integrated soil
amendment matrix was studied with a modified BCR sequential
extraction procedure. The analysis included pseudo-total
concentration determinations according to USEPA 3051A and
relevant physicochemical properties by standardized methods. Based
on the results, the soil amendment matrix possessed neutralization
capacity comparable to commercial fertilizers. Additionally, the
pseudo-total concentrations of all trace elements included in the
Finnish regulation for agricultural fertilizers were lower than the
respective statutory limit values. According to chemical speciation,
the lability of trace elements increased in the following order: Hg <
Cr < Co < Cu < As < Zn < Ni < Pb < Cd < V < Mo < Ba. The
validity of the BCR approach as a tool for chemical speciation was
confirmed by the additional acid digestion phase. Recovery of trace
elements during the procedure assured the validity of the approach
and indicated good quality of the analytical work.
Abstract: This paper proposes a solution to the motion planning
and control problem of a point-mass robot which is required to move
safely to a designated target in a priori known workspace cluttered
with fixed elliptical obstacles of arbitrary position and sizes. A
tailored and unique algorithm for target convergence and obstacle
avoidance is proposed that will work for any number of fixed
obstacles. The control laws proposed in this paper also ensures that
the equilibrium point of the given system is asymptotically stable.
Computer simulations with the proposed technique and applications
to a planar (RP) manipulator will be presented.
Abstract: In this paper we proposed comparison of four content based objective metrics with results of subjective tests from 80 video sequences. We also include two objective metrics VQM and SSIM to our comparison to serve as “reference” objective metrics because their pros and cons have already been published. Each of the video sequence was preprocessed by the region recognition algorithm and then the particular objective video quality metric were calculated i.e. mutual information, angular distance, moment of angle and normalized cross-correlation measure. The Pearson coefficient was calculated to express metrics relationship to accuracy of the model and the Spearman rank order correlation coefficient to represent the metrics relationship to monotonicity. The results show that model with the mutual information as objective metric provides best result and it is suitable for evaluating quality of video sequences.
Abstract: The protection of parallel transmission lines has been a challenging task due to mutual coupling between the adjacent circuits of the line. This paper presents a novel scheme for detection and classification of faults on parallel transmission lines. The proposed approach uses combination of wavelet transform and neural network, to solve the problem. While wavelet transform is a powerful mathematical tool which can be employed as a fast and very effective means of analyzing power system transient signals, artificial neural network has a ability to classify non-linear relationship between measured signals by identifying different patterns of the associated signals. The proposed algorithm consists of time-frequency analysis of fault generated transients using wavelet transform, followed by pattern recognition using artificial neural network to identify the type of the fault. MATLAB/Simulink is used to generate fault signals and verify the correctness of the algorithm. The adaptive discrimination scheme is tested by simulating different types of fault and varying fault resistance, fault location and fault inception time, on a given power system model. The simulation results show that the proposed scheme for fault diagnosis is able to classify all the faults on the parallel transmission line rapidly and correctly.
Abstract: The induction hardening machines are utilized in
the industries which modify machine parts and tools needed to
achieve high ware resistance. This paper describes the model of
induction heating process design of inverter circuit and the results
of induction surface hardening of heating coil. In the design of
heating coil, the shape and the turn numbers of the coil are very
important design factors because they decide the overall operating
performance of induction heater including resonant frequency, Q
factor, efficiency and power factor. The performance will be tested
by experiments in some cases high frequency induction hardening
machine.
Abstract: This paper presents the development of a Bayesian
belief network classifier for prediction of graft status and survival
period in renal transplantation using the patient profile information
prior to the transplantation. The objective was to explore feasibility
of developing a decision making tool for identifying the most suitable
recipient among the candidate pool members. The dataset was
compiled from the University of Toledo Medical Center Hospital
patients as reported to the United Network Organ Sharing, and had
1228 patient records for the period covering 1987 through 2009. The
Bayes net classifiers were developed using the Weka machine
learning software workbench. Two separate classifiers were induced
from the data set, one to predict the status of the graft as either failed
or living, and a second classifier to predict the graft survival period.
The classifier for graft status prediction performed very well with a
prediction accuracy of 97.8% and true positive values of 0.967 and
0.988 for the living and failed classes, respectively. The second
classifier to predict the graft survival period yielded a prediction
accuracy of 68.2% and a true positive rate of 0.85 for the class
representing those instances with kidneys failing during the first year
following transplantation. Simulation results indicated that it is
feasible to develop a successful Bayesian belief network classifier for
prediction of graft status, but not the graft survival period, using the
information in UNOS database.
Abstract: In this paper, an experimentation to enhance the
visibility of hot objects in a thermal image acquired with ordinary
digital camera is reported, after the applications of lowpass and
median filters to suppress the distracting granular noises. The
common thresholding and slicing techniques were used on the
histogram at different gray levels, followed by a subjective
comparative evaluation. The best result came out with the threshold
level 115 and the number of slices 3.
Abstract: Due to a high unemployment rate among local people
and a high reliance on expatriate workers, the governments in the
Gulf Co-operation Council (GCC) countries have been implementing
programmes of localisation (replacing foreign workers with GCC
nationals). These programmes have been successful in the public
sector but much less so in the private sector. However, there are now
insufficient jobs for locals in the public sector and the onus to provide
employment has fallen on the private sector. This paper is concerned
with a study, which is a work in progress (certain elements are
complete but not the whole study), investigating the effective
implementation of localisation policies in four- and five-star hotels in
the Kingdom of Saudi Arabia (KSA) and the United Arab Emirates
(UAE). The purpose of the paper is to identify the research gap, and
to present the need for the research. Further, it will explain how this
research was conducted.
Studies of localisation in the GCC countries are under-represented
in scholarly literature. Currently, the hotel sectors in KSA and UAE
play an important part in the countries’ economies. However, the
total proportion of Saudis working in the hotel sector in KSA is
slightly under 8%, and in the UAE, the hotel sector remains highly
reliant on expatriates. There is therefore a need for research on
strategies to enhance the implementation of the localisation policies
in general and in the hotel sector in particular.
Further, despite the importance of the hotel sector to their
economies, there remains a dearth of research into the
implementation of localisation policies in this sector. Indeed, as far as
the researchers are aware, there is no study examining localisation in
the hotel sector in KSA, and few in the UAE. This represents a
considerable research gap.
Regarding how the research was carried out, a multiple case study
strategy was used. The four- and five-star hotel sector in KSA is one
of the cases, while the four- and five-star hotel sector in the UAE is
the other case. Four- and five-star hotels in KSA and the UAE were
chosen as these countries have the longest established localisation
policies of all the GCC states and there are more hotels of these
classifications in these countries than in any of the other Gulf
countries. A literature review was carried out to underpin the
research. The empirical data were gathered in three phases. In order
to gain a pre-understanding of the issues pertaining to the research
context, Phase I involved eight unstructured interviews with officials
from the Saudi Commission for Tourism and Antiquities (three
interviewees); the Saudi Human Resources Development Fund (one);
the Abu Dhabi Tourism and Culture Authority (three); and the Abu
Dhabi Development Fund (one).
In Phase II, a questionnaire was administered to 24 managers and
24 employees in four- and five-star hotels in each country to obtain
their beliefs, attitudes, opinions, preferences and practices concerning
localisation.
Unstructured interviews were carried out in Phase III with six
managers in each country in order to allow them to express opinions
that may not have been explored in sufficient depth in the
questionnaire. The interviews in Phases I and III were analysed using
thematic analysis and SPSS will be used to analyse the questionnaire
data.
It is recommended that future research be undertaken on a larger
scale, with a larger sample taken from all over KSA and the UAE
rather than from only four cities (i.e., Riyadh and Jeddah in KSA and
Abu Dhabi and Sharjah in the UAE), as was the case in this research.