Abstract: Large metal and concrete structures suffer by various kinds of deterioration, and accurate prediction of the remaining life is important. This paper informs about two methods for its assessment. One method, suitable for steel bridges and other constructions exposed to fatigue, monitors the loads and damage accumulation using information systems for the operation and the finite element model of the construction. In addition to the operation load, the dead weight of the construction and thermal stresses can be included into the model. The second method is suitable for concrete bridges and other structures, which suffer by carbonatation and other degradation processes, driven by diffusion. The diffusion constant, important for the prediction of future development, can be determined from the depth-profile of pH, obtained by pH measurement at various depths. Comparison with measurements on real objects illustrates the suitability of both methods.
Abstract: The development of biomimetic micro-aerial-vehicles
(MAVs) with flapping wings is the future trend in military/domestic
field. The successful flight of MAVs is strongly related to the
understanding of unsteady aerodynamic performance of low Reynolds
number airfoils under dynamic flapping motion. This study explored
the effects of flapping frequency, stroke amplitude, and the inclined
angle of stroke plane on lift force and thrust force of a bio-inspiration
corrugated airfoil with 33 full factorial design of experiment and
ANOVA analysis. Unsteady vorticity flows over a corrugated thin
airfoil executing flapping motion are computed with time-dependent
two-dimensional laminar incompressible Reynolds-averaged
Navier-Stokes equations with the conformal hybrid mesh. The tested
freestream Reynolds number based on the chord length of airfoil as
characteristic length is fixed of 103. The dynamic mesh technique is
applied to model the flapping motion of a corrugated airfoil. Instant
vorticity contours over a complete flapping cycle clearly reveals the
flow mechanisms for lift force generation are dynamic stall, rotational
circulation, and wake capture. The thrust force is produced as the
leading edge vortex shedding from the trailing edge of airfoil to form a
reverse von Karman vortex. Results also indicated that the inclined
angle is the most significant factor on both the lift force and thrust
force. There are strong interactions between tested factors which mean
an optimization study on parameters should be conducted in further
runs.
Abstract: This paper presents one comprehensive modelling approach for maintenance scheduling problem of thermal power units in competitive market. This problem is formulated as a 0/1 mixedinteger linear programming model. Model incorporates long-term bilateral contracts with defined profiles of power and price, and weekly forecasted market prices for market auction. The effectiveness of the proposed model is demonstrated through case study with detailed discussion.
Abstract: Petri Net being one of the most useful graphical tools for modelling complex asynchronous systems, we have used Petri Net to model multi-track railway level crossing system. The roadway has been augmented with four half-size barriers. For better control, a three stage control mechanism has been introduced to ensure that no road-vehicle is trapped on the level crossing. Timed Petri Net is used to include the temporal nature of the signalling system. Safeness analysis has also been included in the discussion section.
Abstract: In this paper, the 1-D conduction-radiation problem is solved by the lattice Boltzmann method. The effects of various parameters such as the scattering albedo, the conduction–radiation parameter and the wall emissivity are studied. In order to check on the accuracy of the numerical technique employed for the solution of the considered problem, the present numerical code was validated with the published study. The found results are in good agreement with those published
Abstract: The possible therapeutic effect of cannabidiol, the major non-psychotropic Cannabis constituent, was investigated against acute hepatotoxicity induced by a single oral dose of acetaminophen (500mg/kg) in mice. Cannabidiol (two intraperitoneal injections, 5mg/kg, each) was given 1 hour and 12 hours following acetaminophen administration. Acetaminophen administration caused significant elevations of serum alanine aminotransferase, and hepatic malondialdehyde, and nitric oxide levels, and a significant decrease in hepatic reduced glutathione. Cannabidiol significantly attenuated the deterioration in the measured biochemical parameters resulted from acetaminophen administration. Also, histopathological examination showed that cannabidiol markedly attenuated ameliorated acetaminophen-induced liver tissue damage. These results emphasize that cannabidiol represents a potential therapeutic option to protect against acetaminophen hepartotoxicity which is a common clinical problem.
Abstract: The purpose of this paper is applied Taguchi method on the optimization for PEMFC performance, and a representative Computational Fluid Dynamics (CFD) model is selectively performed for statistical analysis. The studied factors in this paper are pressure of fuel cell, operating temperature, the relative humidity of anode and cathode, porosity of gas diffusion electrode (GDE) and conductivity of GDE. The optimal combination for maximum power density is gained by using a three-level statistical method. The results confirmed that the robustness of the optimum design parameters influencing the performance of fuel cell are founded by pressure of fuel cell, 3atm; operating temperature, 353K; the relative humidity of anode, 50%; conductivity of GDE, 1000 S/m, but the relative humidity of cathode and porosity of GDE are pooled as error due to a small sum of squares. The present simulation results give designers the ideas ratify the effectiveness of the proposed robust design methodology for the performance of fuel cell.
Abstract: Single nucleotide polymorphisms (SNPs) hold much promise as a basis for disease-gene association. However, research is limited by the cost of genotyping the tremendous number of SNPs. Therefore, it is important to identify a small subset of informative SNPs, the so-called tag SNPs. This subset consists of selected SNPs of the genotypes, and accurately represents the rest of the SNPs. Furthermore, an effective evaluation method is needed to evaluate prediction accuracy of a set of tag SNPs. In this paper, a genetic algorithm (GA) is applied to tag SNP problems, and the K-nearest neighbor (K-NN) serves as a prediction method of tag SNP selection. The experimental data used was taken from the HapMap project; it consists of genotype data rather than haplotype data. The proposed method consistently identified tag SNPs with considerably better prediction accuracy than methods from the literature. At the same time, the number of tag SNPs identified was smaller than the number of tag SNPs in the other methods. The run time of the proposed method was much shorter than the run time of the SVM/STSA method when the same accuracy was reached.
Abstract: Scale Time Offset Robust Modulation (STORM) [1]–
[3] is a high bandwidth waveform design that adds time-scale
to embedded reference modulations using only time-delay [4]. In
an environment where each user has a specific delay and scale,
identification of the user with the highest signal power and that
user-s phase is facilitated by the STORM processor. Both of these
parameters are required in an efficient multiuser detection algorithm.
In this paper, the STORM modulation approach is evaluated with
a direct sequence spread quadrature phase shift keying (DS-QPSK)
system. A misconception of the STORM time scale modulation is that
a fine temporal resolution is required at the receiver. STORM will
be applied to a QPSK code division multiaccess (CDMA) system
by modifying the spreading codes. Specifically, the in-phase code
will use a typical spreading code, and the quadrature code will
use a time-delayed and time-scaled version of the in-phase code.
Subsequently, the same temporal resolution in the receiver is required
before and after the application of STORM. In this paper, the bit error
performance of STORM in a synchronous CDMA system is evaluated
and compared to theory, and the bit error performance of STORM
incorporated in a single user WCDMA downlink is presented to
demonstrate the applicability of STORM in a modern communication
system.
Abstract: A social network is a set of people or organization or other social entities connected by some form of relationships. Analysis of social network broadly elaborates visual and mathematical representation of that relationship. Web can also be considered as a social network. This paper presents an innovative approach to analyze a social network using a variant of existing ant colony optimization algorithm called as Clever Ant Colony Metaphor. Experiments are performed and interesting findings and observations have been inferred based on the proposed model.
Abstract: In this paper, a framework is presented trying to make
the most secure web system out of the available generic and web
security technology which can be used as a guideline for
organizations building their web sites. The framework is designed to
provide necessary security services, to address the known security
threats, and to provide some cover to other security problems
especially unknown threats. The requirements for the design are
discussed which guided us to the design of secure web system. The
designed security framework is then simulated and various quality of
service (QoS) metrics are calculated to measure the performance of
this system.
Abstract: The most planted cover crops in the Czech Republic
are mustard (Sinapis alba) and phacelia (Phacelia tanacetifolia
Benth.). A field trial was executed to evaluate root system size (RSS)
in eight varieties of mustard and five varieties of phacelia on two
locations, in three BBCH phases and in two years. The relationship
between RSS and aboveground biomass was inquired. The root
system was assessed by measuring its electric capacity. Aboveground
mass and root samples to be evaluated by means of a digital image
analysis were recovered in the BBCH phase 70. The yield of
aboveground biomass of mustard was always statistically
significantly higher than that of phacelia. Mustard showed a
statistically significant negative correlation between root length
density (RLD) within 10 cm and aboveground biomass weight (r = -
0.46*). Phacelia featured a statistically significant correlation
between aboveground biomass production and nitrate nitrogen
content in soil (r=0.782**).
Abstract: This paper presents Simulated Annealing based
approach to estimate solar cell model parameters. Single diode solar
cell model is used in this study to validate the proposed approach
outcomes. The developed technique is used to estimate different
model parameters such as generated photocurrent, saturation current,
series resistance, shunt resistance, and ideality factor that govern the
current-voltage relationship of a solar cell. A practical case study is
used to test and verify the consistency of accurately estimating
various parameters of single diode solar cell model. Comparative
study among different parameter estimation techniques is presented
to show the effectiveness of the developed approach.
Abstract: The detection of outliers is very essential because of
their responsibility for producing huge interpretative problem in
linear as well as in nonlinear regression analysis. Much work has
been accomplished on the identification of outlier in linear
regression, but not in nonlinear regression. In this article we propose
several outlier detection techniques for nonlinear regression. The
main idea is to use the linear approximation of a nonlinear model and
consider the gradient as the design matrix. Subsequently, the
detection techniques are formulated. Six detection measures are
developed that combined with three estimation techniques such as the
Least-Squares, M and MM-estimators. The study shows that among
the six measures, only the studentized residual and Cook Distance
which combined with the MM estimator, consistently capable of
identifying the correct outliers.
Abstract: In this paper the Differential Quadrature Method (DQM) is employed to study the coupled lateral-torsional free vibration behavior of the laminated composite beams. In such structures due to the fiber orientations in various layers, the lateral displacement leads to a twisting moment. The coupling of lateral and torsional vibrations is modeled by the bending-twisting material coupling rigidity. In the present study, in addition to the material coupling, the effects of shear deformation and rotary inertia are taken into account in the definition of the potential and kinetic energies of the beam. The governing differential equations of motion which form a system of three coupled PDEs are solved numerically using DQ procedure under different boundary conditions consist of the combinations of simply, clamped, free and other end conditions. The resulting natural frequencies and mode shapes for cantilever beam are compared with similar results in the literature and good agreement is achieved.
Abstract: A nucleotide sequence can be expressed as a numerical sequence when each nucleotide is assigned its proton number. A resulting gene numerical sequence can be investigated for its fractal dimension in terms of evolution and chemical properties for comparative studies. We have investigated such nucleotide fluctuation in the 16S rRNA gene of archaea thermophiles. The studied archaea thermophiles were archaeoglobus fulgidus, methanothermobacter thermautotrophicus, methanocaldococcus jannaschii, pyrococcus horikoshii, and thermoplasma acidophilum. The studied five archaea-euryarchaeota thermophiles have fractal dimension values ranging from 1.93 to 1.97. Computer simulation shows that random sequences would have an average of about 2 with a standard deviation about 0.015. The fractal dimension was found to correlate (negative correlation) with the thermophile-s optimal growth temperature with R2 value of 0.90 (N =5). The inclusion of two aracheae-crenarchaeota thermophiles reduces the R2 value to 0.66 (N = 7). Further inclusion of two bacterial thermophiles reduces the R2 value to 0.50 (N =9). The fractal dimension is correlated (positive) to the sequence GC content with an R2 value of 0.89 for the five archaea-euryarchaeota thermophiles (and 0.74 for the entire set of N = 9), although computer simulation shows little correlation. The highest correlation (positive) was found to be between the fractal dimension and di-nucleotide Shannon entropy. However Shannon entropy and sequence GC content were observed to correlate with optimal growth temperature having an R2 of 0.8 (negative), and 0.88 (positive), respectively, for the entire set of 9 thermophiles; thus the correlation lacks species specificity. Together with another correlation study of bacterial radiation dosage with RecA repair gene sequence fractal dimension, it is postulated that fractal dimension analysis is a sensitive tool for studying the relationship between genotype and phenotype among closely related sequences.
Abstract: The development and application of wind power for
renewable energy has attracted growing interest in recent years. Renewable energy sources are attracting much alteration as they can
reduce both environmental damage and dependence on fossil fuels. With the growing need for sustainable energy supplies, a case is made
for decentralized, stand-alone power supplies (SAPS) as an alternative to power grids. In the era which traditional petroleum energy resource
decreasing and the green house affect significant increasing, the development and usage of regenerative resources is inevitable. Due to the contribution of the pioneers, the development of regenerative resources already has a remarkable achievement; however, in the view of economy and quantity, it is still a long road for regenerative energy
to replace traditional petroleum energy. In our prospective, in stead of
investigate larger regenerative energy equipment, it is much wiser to
think about the blind side and breakthrough of the current technique.
Abstract: Construction projects generally take place in
uncontrolled and dynamic environments where construction waste is
a serious environmental problem in many large cities. The total
amount of waste and carbon dioxide emissions from transportation
vehicles are still out of control due to increasing construction
projects, massive urban development projects and the lack of
effective tools for minimizing adverse environmental impacts in
construction. This research is about utilization of the integrated
applications of automated advanced tracking and data storage
technologies in the area of environmental management to monitor
and control adverse environmental impacts such as construction
waste and carbon dioxide emissions. Radio Frequency Identification
(RFID) integrated with the Global Position System (GPS) provides
an opportunity to uniquely identify materials, components, and
equipments and to locate and track them using minimal or no worker
input. The transmission of data to the central database will be carried
out with the help of Global System for Mobile Communications
(GSM).
Abstract: The zinc and iron environments in different growth
stages have been studied with EXAFS and XANES with Brookhaven
Synchrotron Light Source. Tissue samples included meat, organ,
vegetable, leaf, and yeast. The project studied the EXAFS and
XANES of tissue samples using Zn and Fe K-edges. Duck embryo
samples show that brain and intestine would contain shorter EXFAS
determined Zn-N/O bond; as with the cases of fresh yeast versus
reconstituted live yeast and green leaf versus yellow leaf. The
XANES Fourier transform characteristic-length would be useful as a
functionality index for selected types of tissue samples in various
physical states. The extension to the development of functional
synchrotron imaging for tissue engineering application based on
spectroscopic technique is discussed.
Abstract: The operation performance of a valveless micro-pump
is strongly dependent on the shape of connected nozzle/diffuser and
Reynolds number. The aims of present work are to compare the
performance curves of micropump with the original straight
nozzle/diffuser and contoured nozzle/diffuser under different back
pressure conditions. The tested valveless micropumps are assembled
of five pieces of patterned PMMA plates with hot-embracing
technique. The structures of central chamber, the inlet/outlet
reservoirs and the connected nozzle/diffuser are fabricated with laser
cutting machine. The micropump is actuated with circular-type PZT
film embraced on the bottom of central chamber. The deformation of
PZT membrane with various input voltages is measured with a
displacement laser probe. A simple testing facility is also constructed
to evaluate the performance curves for comparison.
In order to observe the evaluation of low Reynolds number
multiple vortex flow patterns within the micropump during suction
and pumping modes, the unsteady, incompressible laminar
three-dimensional Reynolds-averaged Navier-Stokes equations are
solved. The working fluid is DI water with constant thermo-physical
properties. The oscillating behavior of PZT film is modeled with the
moving boundary wall in way of UDF program. With the dynamic
mesh method, the instants pressure and velocity fields are obtained
and discussed.Results indicated that the volume flow rate is not
monotony increased with the oscillating frequency of PZT film,
regardless of the shapes of nozzle/diffuser. The present micropump
can generate the maximum volume flow rate of 13.53 ml/min when
the operation frequency is 64Hz and the input voltage is 140 volts.
The micropump with contoured nozzle/diffuser can provide 7ml/min
flow rate even when the back pressure is up to 400 mm-H2O. CFD
results revealed that the flow central chamber was occupied with
multiple pairs of counter-rotating vortices during suction and
pumping modes. The net volume flow rate over a complete
oscillating periodic of PZT