Abstract: As a part of routine oesophageal HDR Brachytherapy procedure, treatment planning takes about 45 minutes while patients are under light sedation. Some patients may suffer gagging and/or spasms before the 90-minute brachytherapy procedure complete, and the treatment may need to be aborted. A pre-prepared plan generated before patient’s sedation may reduce the brachytherapy procedure time by 40 minutes. This paper reports rationality and evidence of pre-prepared treatment plans. A retrospective study of 28 patients confirms that pre-prepared plans would be acceptable for all reviewed patients. The rationality is further confirmed by a systemic study with a wide range of applicator curvature and treatment volume. Detailed comparison between CT based treatment plans and pre-prepared plans are discussed. The argument holds for endobronchial HDR brachytherapy too. With the above evidence, pre-prepared plans have been used for all oesophageal and endobronchial HDR brachytherapy cases in our clinic.
Abstract: This paper explains the cause of nonlinearity in floor
attenuation hither to left unexplained. The performance degradation
occurring in air interface for GSM signals is quantitatively analysed
using the concept of Radiating Columns of buildings. The signal
levels were measured using Wireless Network Optimising Drive Test
Tool (E6474A of Agilent Technologies). The measurements were
taken in reflected signal environment under usual fading conditions
on actual GSM signals radiated from base stations. A mathematical
model is derived from the measurements to predict the GSM signal
levels in different floors. It was applied on three buildings and found
that the predicted signal levels deviated from the measured levels
with in +/- 2 dB for all floors. It is more accurate than the prediction
models based on Floor Attenuation Factor. It can be used for
planning proper indoor coverage in multi storey buildings.
Abstract: The localization of software products is essential for reaching the users of the international market. An important task for this is the translation of the user interface into local national languages. As graphical interfaces are usually optimized for the size of the texts in the original language, after the translation certain user controls (e.g. text labels and buttons in dialogs) may grow in such a manner that they slip above each other. This not only causes an unpleasant appearance but also makes the use of the program more difficult (or even impossible) which implies that the arrangement of the controls must be corrected subsequently. The correction should preserve the original structure of the interface (e.g. the relation of logically coherent controls), furthermore, it is important to keep the nicely proportioned design: the formation of large empty areas should be avoided. This paper describes an algorithm that automatically rearranges the controls of a graphical user interface based on the principles above. The algorithm has been implemented and integrated into a translation support system and reached results pleasant for the human eye in most test cases.
Abstract: This paper has as its main aim to analyse how
corporate web pages can become an essential tool in order to detect
strategic trends by firms or sectors, and even a primary source for
benchmarking. This technique has made it possible to identify the key
issues in the strategic management of the most excellent large Spanish
firms and also to describe trends in their long-range planning, a way of
working that can be generalised to any country or firm group. More
precisely, two objectives were sought. The first one consisted in showing
the way in which corporate websites make it possible to obtain direct
information about the strategic variables which can define firms. This
tool is dynamic (since web pages are constantly updated) as well as
direct and reliable, since the information comes from the firm itself, not
from comments of third parties (such as journalists, academicians,
consultants...). When this information is analysed for a group of firms,
one can observe their characteristics in terms of both managerial tasks
and business management. As for the second objective, the methodology
proposed served to describe the corporate profile of the large Spanish
enterprises included in the Ibex35 (the Ibex35 or Iberia Index is the
reference index in the Spanish Stock Exchange and gathers periodically
the 35 most outstanding Spanish firms). An attempt is therefore made to
define the long-range planning that would be characteristic of the largest
Spanish firms.
Abstract: Widespread use of asbestos over the last century has left a terrible legacy of lung disease. Doctors knew of the health risks long ago, but almost nothing was done to protect workers and the public. Some aspects of nanotechnology may have risks similar to asbestos.
Abstract: The objective of this study was to evaluate the
distribution patterns of Cd, Zn and Hg in groundwater by geospatial
interpolation. The study was performed at Rayong province in the
eastern part of Thailand, with high agricultural and industrial
activities. Groundwater samples were collected twice a year from 31
tubewells around this area. Inductively Coupled Plasma-Atomic
Emission Spectrometer (ICP-AES) was used to measure the
concentrations of Cd, Zn, and Hg in groundwater samples. The
results demonstrated that concentrations of Cd, Zn and Hg range
from 0.000-0.297 mg/L (x = 0.021±0.033 mg/L), 0.022-33.236 mg/L
(x = 4.214±4.766 mg/L) and 0.000-0.289 mg/L (x = 0.023±0.034
mg/L), respectively. Most of the heavy metals concentrations were
exceeded groundwater quality standards as specified in the Ministry
of Natural Resources and Environment, Thailand. The trend
distribution of heavy metals were high concentrations at the
southeastern part of the area that especially vulnerable to heavy
metals and other contaminants.
Abstract: The effects of upflow liquid velocity (ULV) on
performance of expanded granular sludge bed (EGSB) system were
investigated. The EGSB reactor, made from galvanized steel pipe
0.10 m diameter and 5 m height, had been used to treat piggery
wastewater, after passing through acidification tank. It consisted of
39.3 l working volume in reaction zone and 122 l working volume in
sedimentation zone, at the upper part. The reactor was seeded with
anaerobically digested sludge and operated at the ULVs of 4, 8, 12
and 16 m/h, consecutively, corresponding to organic loading rates of
9.6 – 13.0 kg COD/ (m3.d). The average COD concentrations in the
influent were 9,601 – 13,050 mg/l. The COD removal was not
significantly different, i.e. 93.0% - 94.0%, except at ULV 12 m/h where
SS in the influent was exceptionally high so that VSS washout had
occurred, leading to low COD removal. The FCOD and VFA
concentrations in the effluent of all experiments were not much
different, indicating the same range of treatment performance. The
biogas production decreased at higher ULV and ULV of 4 m/h is
suggested as design criterion for EGSB system.
Abstract: Clustering is one of an interesting data mining topics
that can be applied in many fields. Recently, the problem of cluster
analysis is formulated as a problem of nonsmooth, nonconvex optimization,
and an algorithm for solving the cluster analysis problem
based on nonsmooth optimization techniques is developed. This
optimization problem has a number of characteristics that make it
challenging: it has many local minimum, the optimization variables
can be either continuous or categorical, and there are no exact
analytical derivatives. In this study we show how to apply a particular
class of optimization methods known as pattern search methods
to address these challenges. These methods do not explicitly use
derivatives, an important feature that has not been addressed in
previous studies. Results of numerical experiments are presented
which demonstrate the effectiveness of the proposed method.
Abstract: Recently, we have presented an initial implementation
of a model agent-based e-commerce system, which utilized a simple
price negotiation mechanism–English Auction. In this note we
discuss how a Dutch Auction involving multiple units of a product
can be included in our system. We present UML diagrams of
agents involved in price negotiations and briefly discuss rule-based
mechanism exemplifying Dutch Auction.
Abstract: Potassium monopersulfate has been decomposed in
aqueous solution in the presence of Co(II). The effect of the main
operating variables has been assessed. Minimum variations in pH
exert a considerable influence on the process kinetics. Thus, when no
pH adjustment is considered, the actual effect of variables like initial
monopersulfate and/or catalyst concentration may be hindered. As
expected, temperature enhances the monopersulfate decomposition
rate by following the Arrhenius law. The activation energy in the
proximity of 85 kJ/mol has been obtained. Amongst the different
solids tested in the monopersulfate decomposition, only the
perovskite LaTi0.15Cu0.85O3 has shown a significant catalytic activity.
Abstract: The machining of Carbon Fiber Reinforced Plastics
has come to constitute a significant challenge for many fields of
industry. The resulting surface finish of machined parts is of primary
concern for several reasons, including contact quality and impact on
the assembly. Therefore, the characterization and prediction of
roughness based on machining parameters are crucial for costeffective
operations. In this study, a PCD tool comprised of two
straight flutes was used to trim 32-ply carbon fiber laminates in a bid
to analyze the effects of the feed rate and the cutting speed on the
surface roughness. The results show that while the speed has but a
slight impact on the surface finish, the feed rate for its part affects it
strongly. A detailed study was also conducted on the effect of fiber
orientation on surface roughness, for quasi-isotropic laminates used
in aerospace. The resulting roughness profiles for the four-ply
orientation lay-up were compared, and it was found that fiber angle is
a critical parameter relating to surface roughness. One of the four
orientations studied led to very poor surface finishes, and
characteristic roughness profiles were identified and found to only
relate to the ply orientations of multilayer carbon fiber laminates.
Abstract: This comparison of valuation techniques for bone age
assessment is a work carried out by the Telemedicine Research Group
of the Military University - TIGUM, as a preliminary to the Design
and development a treatment system of hand and wrist radiological
images for children aged 0-6 years to bone age assessment . In this
paper the techniques mentioned for decades have been the most
widely used and the statistically significant.
Althought, initially with the current project, it wants to work with
children who have limit age, this comparison and evaluation
techniques work will help in the future to expand the study subject in
the system to bone age assessment, implementing more techniques,
tools and deeper analysis to accomplish this purpose.
Abstract: This paper presents a new type of mechanism and trajectory planning strategy for bipedal walking robot. The newly designed mechanism is able to improve the performance of bipedal walking robot in terms of energy efficiency and weight reduction by utilizing minimum number of actuators. The usage of parallelogram mechanism eliminates the needs of having an extra actuator at the knee joint. This mechanism works together with the joint space trajectory planning in order to realize straight legged walking which cannot be achieved by conventional inverse kinematics trajectory planning due to the singularity. The effectiveness of the proposed strategy is confirmed by computer simulation results.
Abstract: In this study, we introduced a communication system
where human body was used as medium through which data were
transferred. Multiple biosignal sensing units were attached to a subject
and wireless personal area network was formed. Data of the sensing
units were shared among them. We used wideband pulse
communication that was simple, low-power consuming and high data
rated. Each unit functioned as independent communication device or
node. A method of channel search and communication among the
modes was developed. A protocol of carrier sense multiple
access/collision detect was implemented in order to avoid data
collision or interferences. Biosignal sensing units should be located at
different locations due to the nature of biosignal origin. Our research
provided a flexibility of collecting data without using electrical wires.
More non-constrained measurement was accomplished which was
more suitable for u-Health monitoring.
Abstract: The estrus female Etawah cross bred goats were
synchronized estrus by controlled internal drug release (CIDR)
implants for 10 days combined with PGF2α injection, and continued
by artificial insemination (AI) within the hours of 24 period. Vaginal
epithelium was taken to determine estrus cycle of the goats without
estrus synchronization. The estrus responds (the puffy of vulva and
vaginal pH) and percentage of pregnancy were investigated. The data
were analyzed descriptively and Independent Sample T-Test. The
results showed that the puffy of vulva and vaginal pH were
significantly different in synchronized estrus goats and control goats
(2.18 ± 0.33 cm vs. 1.20 ± 0.16 cm and 8.55 ± 0.63 vs. 8.22 ± 0.22).
Percentage of pregnancy was higher in synchronized estrus goats
(73.33%) than in control (53.3%). Estrus synchronization by using
CIDR implants and PGF2, continued by AI was effective to improve
reproduction performance of Etawah cross bred goats.
Abstract: The aim of this work is to investigate on the internalflow
patterns in a plate heat exchanger channel, which affect the
rate of sedimentation fouling on the heat transfer surface of the
plate heat exchanger. The research methodologies were the
computer simulation using Computational Fluid Dynamics (CFD)
and the experimental works. COMSOL MULTIPHYSICS™
Version 3.3 was used to simulate the velocity flow fields to verify
the low and high flow regions. The results from the CFD technique
were then compared with the images obtained from the
experiments in which the fouling test rig was set up with a singlechannel
plate heat exchanger to monitor the fouling of calcium
carbonate. Two parameters were varied i.e., the crossing angle of
the two plate: 55/55, 10/10, and 55/10 degree, and the fluid flow
rate at the inlet: 0.0566, 0.1132 and 0.1698 m/s. The type of plate
“GX-12" (the surface area 0.12 m2, the depth 2.9 mm, the width of
fluid flow 215 mm and the thickness of stainless plate of 0.5 mm)
was used in this study. The results indicated that the velocity
distribution for the case of 55/55 degree seems to be very well
organized when compared with the others. Also, an increase in the
inlet velocity resulted in the reduction of fouling rate on the surface
of plate heat exchangers.
Abstract: This study suggests how an order-receiving company
can avoid disclosing schedule information on unit tasks to the
order-placing company when carrying out a collaborative project on
the value chain in an order-oriented industry. Specifically, it suggests
methods for keeping schedule information confidential, and
categorizes potential situations by inter-task dependency. Lastly, an
approach to select the most optimal non-disclosure method is
discussed. With the methods for not disclosing work-related
information suggested in the study, order-receiving companies can
logically deal with political issues relating to the question of whether
or not to disclose information upon the execution of a collaborative
project in cooperation with an order-placing firm. Moreover,
order-placing companies can monitor undistorted information, while
respecting the legitimate rights of an order-receiving company.
Therefore, it is fair to say that the suggestions made in this study will
contribute to the smooth operation of collaborative intercompany
projects.
Abstract: In this paper, we propose a method to reduce the
various kinds of noise while gathering and recording the
electrocardiogram (ECG) signal. Because of the defects of former
method in the noise elimination of ECG signal, we use translation
invariant (TI) multiwavelet denoising method to the noise elimination.
The advantage of the proposed method is that it may not only remain
the geometrical characteristics of the original ECG signal and keep the
amplitudes of various ECG waveforms efficiently, but also suppress
impulsive noise to some extent. The simulation results indicate that the
proposed method are better than former removing noise method in
aspects of remaining geometrical characteristics of ECG signal and the
signal-to-noise ratio (SNR).
Abstract: One of the important steps in a safety and risk management system is the economical evaluation of occupational accident and diseases costs in order to decrease accidents from reoccurring in the workplace. This study proposed a plausible method for calculating occupational accident costs and illnesses in work place. This method design for cost estimation takes into account both the personnel, organizational level as well as the community level especially intended for an Iranian work place. The research indicates that a using systematic method for calculating costs which also provides risk evaluation can help managers to plan correctly the investment in health and safety measures. Using this method is that not only is it comprehensive, easy and practical and could be applied in practice by a manager within a short period of time but it also shows the importance of accident costs as well as calculates the real cost of an accident and illnesses.
Abstract: In this paper, we research the standard 13-point difference schemes for solving the biharmonic equation. Heuristic method is applied to judging the stability of multi-level difference schemes of the biharmonic equation. It is showed that the standard 13-point difference schemes are stable.