Abstract: A Comparison and evaluation of the different
condition monitoring (CM) techniques was applied experimentally
on RC e.g. Dynamic cylinder pressure and crankshaft Instantaneous
Angular Speed (IAS), for the detection and diagnosis of valve faults
in a two - stage reciprocating compressor for a programme of
condition monitoring which can successfully detect and diagnose a
fault in machine. Leakage in the valve plate was introduced
experimentally into a two-stage reciprocating compressor. The effect
of the faults on compressor performance was monitored and the
differences with the normal, healthy performance noted as a fault
signature been used for the detection and diagnosis of faults.
The paper concludes with what is considered to be a unique
approach to condition monitoring. First, each of the two most useful
techniques is used to produce a Truth Table which details the
circumstances in which each method can be used to detect and
diagnose a fault. The two Truth Tables are then combined into a
single Decision Table to provide a unique and reliable method of
detection and diagnosis of each of the individual faults introduced
into the compressor. This gives accurate diagnosis of compressor
faults.
Abstract: Dredged sediment (DS) was utilized as source of
silt-clay and organic matter in artificially prepared eelgrass substrates with mountain sand (MS) as the sand media. Addition of DS showed
improved growth of eelgrass in the mixed substrates. Increase in added
DS up to 15% silt-clay showed increased shoot growth but additional
DS in 20% silt-clay mixture didn-t result to further increase in eelgrass
growth. Improved root establishment were also found for plants in pots
with added DS as shown by the increased resistance to uprooting, increased number of rhizome nodes and longer roots. Results demonstrated that addition of DS may be beneficial to eelgrass up to a
certain extent only and too much of it might be harmful to eelgrass plants.
Abstract: Let R be a ring and n a fixed positive integer, we
investigate the properties of n-strongly Gorenstein projective, injective
and flat modules. Using the homological theory , we prove that
the tensor product of an n-strongly Gorenstein projective (flat) right
R -module and projective (flat) left R-module is also n-strongly
Gorenstein projective (flat). Let R be a coherent ring ,we prove that
the character module of an n -strongly Gorenstein flat left R -module
is an n-strongly Gorenstein injective right R -module . At last, let
R be a commutative ring and S a multiplicatively closed set of R ,
we establish the relation between n -strongly Gorenstein projective
(injective , flat ) R -modules and n-strongly Gorenstein projective
(injective , flat ) S−1R-modules. All conclusions in this paper is
helpful for the research of Gorenstein dimensions in future.
Abstract: In the past few years there is a change in the view of high performance applications and parallel computing. Initially such applications were targeted towards dedicated parallel machines. Recently trend is changing towards building meta-applications composed of several modules that exploit heterogeneous platforms and employ hybrid forms of parallelism. The aim of this paper is to propose a model of virtual parallel computing. Virtual parallel computing system provides a flexible object oriented software framework that makes it easy for programmers to write various parallel applications.
Abstract: The purpose of this paper is to solve the problem of protecting aerial lines from high impedance faults (HIFs) in distribution systems. This investigation successfully applies 3I0 zero sequence current to solve HIF problems. The feature extraction system based on discrete wavelet transform (DWT) and the feature identification technique found on statistical confidence are then applied to discriminate effectively between the HIFs and the switch operations. Based on continuous wavelet transform (CWT) pattern recognition of HIFs is proposed, also. Staged fault testing results demonstrate that the proposed wavelet based algorithm is feasible performance well.
Abstract: This paper presents the modeling results of an
innovative system for the temperature control in the interior
compartment of a stationary automobile facing the solar energy from
the sun. A very thin layer of PCM inside a pouch placed in the
ceiling of the car in which the heating energy is absorbed and release
with melting and solidification of phase change materials. As a result
the temperature of the car interior is maintained in the comfort
condition. The amount of required PCM has been calculated to be
about 755 g. The PCM-temperature controlling system is simple and
has a potential to be implemented as a practical solution to prevent
undesirable heating of the automobile-s cabin.
Abstract: In this paper, to resolve the problem of existing
schemes, an alternative fast handover Proxy Mobile IPv6 (PMIPv6)
scheme using the IEEE 802.21 Media Independent Handover (MIH)
function is proposed for heterogeneous wireless networks. The proposed
scheme comes to support fast handover for the mobile node
(MN) irrespective of the presence or absence of MIH functionality
as well as L3 mobility functionality, whereas the MN in existing
schemes has to implement MIH functionality. That is, the proposed
scheme does not require the MN to be involved in MIH related signaling
required for handover procedure. The base station (BS) with MIH
functionality performs handover on behalf of the MN. Therefore, the
proposed scheme can reduce burden and power consumption of MNs
with limited resource and battery power since MNs are not required
to be involved for the handover procedure. In addition, the proposed
scheme can reduce considerably traffic overhead over wireless links
between MN and BS since signaling messages are reduced.
Abstract: This paper describes the Multilingual Virtual Simulated Patient framework. It has been created to train the social skills and testing the knowledge of primary health care medical students. The framework generates conversational agents which perform in serveral languages as virtual simulated patients that help to improve the communication and diagnosis skills of the students complementing their training process.
Abstract: The main objective of this paper is to analyse the influence of preparation and control of orders on performance. The focused activities explored in this research are: procurement, production and distribution. These changes in performance were obtained through improvement of the supply chain. It is proved using all the company activities that it is possible to increase de efficiency and do services in an adequate way, placing the products in the market efficiently. For that, it was explored the importance of the supply chain, with privilege to the practical environment and the quantification of the obtained results.
Abstract: Car accident is one of the major causes of death in many countries. Many researchers have attempted to design and develop techniques to increase car safety in the past recent years. In spite of all the efforts, it is still challenging to design a system adaptive to the driver rather than the automotive characteristics. In this paper, the adaptive car safety system is explained which attempts to find a balance.
Abstract: For stable bipedal gait generation on the level floor,
efficient restoring of mechanical energy lost by heel collision at
the ground is necessary. Parametric excitation principle is one of
the solutions. We dealt with the robot-s total center of mass as
an inverted pendulum to consider the total dynamics of the robot.
Parametrically excited walking requires the use of continuous target
trajectory that is close to discontinuous optimal trajectory. In this
paper, we proposed the new target trajectory based on a position
in the walking direction. We surveyed relations between walking
performance and the parameters that form the target trajectory via
numerical simulations. As a result, it was found that our target
trajectory has the similar characteristics of a parametrically excited
inverted pendulum.
Abstract: In this paper we present a method of abrupt cut detection with a novel logic of frames- comparison. Actual frame is compared with its motion estimated prediction instead of comparison with successive frame. Four different similarity metrics were employed to estimate the resemblance of compared frames. Obtained results were evaluated by standard used measures of test accuracy and compared with existing approach. Based on the results, we claim the proposed method is more effective and Pearson correlation coefficient obtained the best results among chosen similarity metrics.
Abstract: This paper presents a experiment to estimate the
influences of cutting conditions in microstructure changes of
machining austenitic 304 stainless steel, especially for wear insert. The
wear insert were prefabricated with a width of 0.5 mm. And the forces,
temperature distribution, RS, and microstructure changes were
measured by force dynamometer, infrared thermal camera, X-ray
diffraction, XRD, SEM, respectively. The results told that the different
combinations of machining condition have a significant influence on
machined surface microstructure changes. In addition to that, the
ANOVA and AOMwere used to tell the different influences of cutting
speed, feed rate, and wear insert.
Abstract: The extraction of meaningful information from image
could be an alternative method for time series analysis. In this paper,
we propose a graphical analysis of time series grouped into table
with adjusted colour scale for numerical values. The advantages of
this method are also discussed. The proposed method is easy to
understand and is flexible to implement the standard methods of
pattern recognition and verification, especially for noisy
environmental data.
Abstract: In this paper, we present local image descriptor using
VQ-SIFT for more effective and efficient image retrieval. Instead of
SIFT's weighted orientation histograms, we apply vector quantization
(VQ) histogram as an alternate representation for SIFT features.
Experimental results show that SIFT features using VQ-based local
descriptors can achieve better image retrieval accuracy than the
conventional algorithm while the computational cost is significantly
reduced.
Abstract: Work stress causes the organizational work-life
imbalance of employees. Because of this imbalance, workers perform
with lower effort to finish assignments and thus an organization will
experience reduced productivity. In order to investigate the problem
of an organizational work-life imbalance, this qualitative case study
focuses on an organizational work-life imbalance among Thai
software developers in a German-owned company in Chiang Mai,
Thailand. In terms of knowledge management, fishbone diagram is
useful analysis tool to investigate the root causes of an organizational
work-life imbalance systematically in focus-group discussions.
Furthermore, fishbone diagram shows the relationship between
causes and effects clearly. It was found that an organizational worklife
imbalance among Thai software developers is influenced by
management team, work environment, and information tools used in
the company over time.
Abstract: The effect of wheat flour extraction rates on flour
composition, farinographic characteristics and the quality of
sourdough naans was investigated. The results indicated that by
increasing the extraction rate, the amount of protein, fiber, fat and
ash increased, whereas moisture content decreased. Farinographic
characteristic like water absorption and dough development time
increased with an increase in flour extraction rate but the dough
stabilities and tolerance indices were reduced with an increase in
flour extraction rates. Titratable acidity for both sourdough and
sourdough naans also increased along with flour extraction rate. The
study showed that overall quality of sourdough naans were affected
by both flour extraction rate and starter culture used. Sensory
analysis of sourdough naans revealed that desirable extraction rate
for sourdough naan was 76%.
Abstract: Groundwater has become the most dependable source
of fresh water for agriculture, domestic and industrial uses in the past
few decades. This wide use of groundwater if left uncontrolled and
unseen will lead to overexploitation causing sea water intrusion in the
coastal areas and illegal water marketing. Several Policies and Acts
have been enacted to regulate and manage the use of this valuable
resource. In spite of this the over extraction of groundwater beyond
the recharging capacity of aquifers and depletion in the quality of
groundwater is continuing. The current study aims at reviewing the
Acts and Policies existing in the State of Tamil Nadu and in the
National level regarding groundwater regulation and management.
Further an analysis is made on the rights associated with the usage of
groundwater resources and the gaps in these policies have been
analyzed. Some suggestions are made to reform the existing
groundwater policies for better management and regulation of the
resource.
Abstract: In this paper, a delayed physiological control system is investigated. The sufficient conditions for stability of positive equilibrium and existence of local Hopf bifurcation are derived. Furthermore, global existence of periodic solutions is established by using the global Hopf bifurcation theory. Finally, numerical examples are given to support the theoretical analysis.
Abstract: In this paper, a new formulation for acoustics coupled with linear elasticity is presented. The primary objective of the work is to develop a three dimensional hp adaptive finite element method code destinated for modeling of acoustics of human head. The code will have numerous applications e.g. in designing hearing protection devices for individuals working in high noise environments. The presented work is in the preliminary stage. The variational formulation has been implemented and tested on a sequence of meshes with concentric multi-layer spheres, with material data representing the tissue (the brain), skull and the air. Thus, an efficient solver for coupled elasticity/acoustics problems has been developed, and tested on high contrast material data representing the human head.