Abstract: Simulation of the flow and sedimentation process in
the reservoir dams can be made by two methods of physical and mathematical modeling. The study area was within a region which
ranged from the Jelogir hydrometric station to the Karkheh reservoir
dam aimed at investigating the effects of stream tubes on the
GSTARS-3 model behavior. The methodologies was to run the model based on 5 stream tubes in order to observe the influence of
each scenario on longitudinal profiles, cross-section, flow velocity and bed load sediment size. Results further suggest that the use of
two stream tubes or more which result in the semi-two-dimensional
model will yield relatively closer results to the observational data
than a singular stream tube modeling. Moreover, the results of
modeling with three stream tubes shown to yield a relatively close
results with the observational data. The overall conclusion of the paper is with applying various stream tubes; it would be possible to yield a significant influence on the modeling behavior Vis-a Vis the bed load sediment size.
Abstract: The System Identification problem looks for a
suitably parameterized model, representing a given process. The
parameters of the model are adjusted to optimize a performance
function based on error between the given process output and
identified process output. The linear system identification field is
well established with many classical approaches whereas most of
those methods cannot be applied for nonlinear systems. The problem
becomes tougher if the system is completely unknown with only the
output time series is available. It has been reported that the
capability of Artificial Neural Network to approximate all linear and
nonlinear input-output maps makes it predominantly suitable for the
identification of nonlinear systems, where only the output time series
is available. [1][2][4][5]. The work reported here is an attempt to
implement few of the well known algorithms in the context of
modeling of nonlinear systems, and to make a performance
comparison to establish the relative merits and demerits.
Abstract: Efforts to secure supervisory control and data acquisition
(SCADA) systems must be supported under the guidance of
sound security policies and mechanisms to enforce them. Critical
elements of the policy must be systematically translated into a format
that can be used by policy enforcement components. Ideally, the
goal is to ensure that the enforced policy is a close reflection of
the specified policy. However, security controls commonly used to
enforce policies in the IT environment were not designed to satisfy
the specific needs of the SCADA environment. This paper presents
a language, based on the well-known XACML framework, for the
expression of authorization policies for SCADA systems.
Abstract: This paper presents an overview of the design and
implementation of an online rule-based Expert Systems for Islamic
medication. T his Online Islamic Medication Expert System (OIMES)
focuses on physical illnesses only. Knowledge base of this Expert
System contains exhaustively the types of illness together with their
related cures or treatments/therapies, obtained exclusively from the
Quran and Hadith. Extensive research and study are conducted to
ensure that the Expert System is able to provide the most suitable
treatment with reference to the relevant verses cited in Quran or
Hadith. These verses come together with their related 'actions'
(bodily actions/gestures or some acts) to be performed by the patient
to treat a particular illness/sickness. These verses and the instructions
for the 'actions' are to be displayed unambiguously on the computer
screen. The online platform provides the advantage for patient getting
treatment practically anytime and anywhere as long as the computer
and Internet facility exist. Patient does not need to make appointment
to see an expert for a therapy.
Abstract: In this paper, a novel approach is presented
for designing multiplier-free state-space digital filters. The
multiplier-free design is obtained by finding power-of-2 coefficients
and also quantizing the state variables to power-of-2
numbers. Expressions for the noise variance are derived for the
quantized state vector and the output of the filter. A “structuretransformation
matrix" is incorporated in these expressions. It
is shown that quantization effects can be minimized by properly
designing the structure-transformation matrix. Simulation
results are very promising and illustrate the design algorithm.
Abstract: We report the electronic structure and optical
properties of NdF3 compound. Our calculations are based on density
functional theory (DFT) using the full potential linearized augmented
plane wave (FPLAPW) method with the inclusion of spin orbit
coupling. We employed the local spin density approximation (LSDA)
and Coulomb-corrected local spin density approximation, known for
treating the highly correlated 4f electrons properly, is able to
reproduce the correct insulating ground state. We find that the
standard LSDA approach is incapable of correctly describing the
electronic properties of such materials since it positions the f-bands
incorrectly resulting in an incorrect metallic ground state. On the
other hand, LSDA + U approximation, known for treating the highly
correlated 4f electrons properly, is able to reproduce the correct
insulating ground state. Interestingly, however, we do not find any
significant differences in the optical properties calculated using
LSDA, and LSDA + U suggesting that the 4f electrons do not play a
decisive role in the optical properties of these compounds. The
reflectivity for NdF3 compound stays low till 7 eV which is
consistent with their large energy gaps. The calculated energy gaps
are in good agreement with experiments. Our calculated reflectivity
compares well with the experimental data and the results are analyzed
in the light of band to band transitions.
Abstract: New methodologies for XOR-XNOR circuits are
proposed to improve the speed and power as these circuits are basic
building blocks of many arithmetic circuits. This paper evaluates and
compares the performance of various XOR-XNOR circuits. The
performance of the XOR-XNOR circuits based on TSMC 0.18μm
process models at all range of the supply voltage starting from 0.6V
to 3.3V is evaluated by the comparison of the simulation results
obtained from HSPICE. Simulation results reveal that the proposed
circuit exhibit lower PDP and EDP, more power efficient and faster
when compared with best available XOR-XNOR circuits in the
literature.
Abstract: Mixed model assembly lines (MMAL) are a type of
production line where a variety of product models similar in product
characteristics are assembled. The effective design of these lines
requires that schedule for assembling the different products is
determined. In this paper we tried to fit the sequencing problem with
the main characteristics of make to order (MTO) environment. The
problem solved in this paper is a multiple objective sequencing
problem in mixed model assembly lines sequencing using weighted
Sum Method (WSM) using GAMS software for small problem and
an effective GA for large scale problems because of the nature of
NP-hardness of our problem and vast time consume to find the
optimum solution in large problems. In this problem three practically
important objectives are minimizing: total utility work, keeping a
constant production rate variation, and minimizing earliness and
tardiness cost which consider the priority of each customer and
different due date which is a real situation in mixed model assembly
lines and it is the first time we consider different attribute to
prioritize the customers which help the company to reduce the cost of
earliness and tardiness. This mechanism is a way to apply an advance
available to promise (ATP) in mixed model assembly line sequencing
which is the main contribution of this paper.
Abstract: One of the most important applications of
wireless sensor networks is data collection. This paper
proposes as efficient approach for data collection in wireless
sensor networks by introducing Member Forward List. This list
includes the nodes with highest priority for forwarding the data.
When a node fails or dies, this list is used to select the next node
with higher priority. The benefit of this node is that it prevents
the algorithm from repeating when a node fails or dies. The
results show that Member Forward List decreases power
consumption and latency in wireless sensor networks.
Abstract: This paper presented a novel combined cycle of air separation and natural gas liquefaction. The idea is that natural gas can be liquefied, meanwhile gaseous or liquid nitrogen and oxygen are produced in one combined cryogenic system. Cycle simulation and exergy analysis were performed to evaluate the process and thereby reveal the influence of the crucial parameter, i.e., flow rate ratio through two stages expanders β on heat transfer temperature difference, its distribution and consequent exergy loss. Composite curves for the combined hot streams (feeding natural gas and recycled nitrogen) and the cold stream showed the degree of optimization available in this process if appropriate β was designed. The results indicated that increasing β reduces temperature difference and exergy loss in heat exchange process. However, the maximum limit value of β should be confined in terms of minimum temperature difference proposed in heat exchanger design standard and heat exchanger size. The optimal βopt under different operation conditions corresponding to the required minimum temperature differences was investigated.
Abstract: This paper focuses on the Mega-Sub Controlled
Structure Systems (MSCSS) performances and characteristics
regarding the new control principle contained in MSCSS subjected to
strong earthquake excitations. The adopted control scheme consists of
modulated sub-structures where the control action is achieved by
viscous dampers and sub-structure own configuration. The
elastic-plastic time history analysis under severe earthquake excitation
is analyzed base on the Finite Element Analysis Method (FEAM), and
some comparison results are also given in this paper. The result shows
that the MSCSS systems can remarkably reduce vibrations effects
more than the mega-sub structure (MSS). The study illustrates that the
improved MSCSS presents good seismic resistance ability even at 1.2g
and can absorb seismic energy in the structure, thus imply that
structural members cross section can be reduce and achieve to good
economic characteristics. Furthermore, the elasto-plastic analysis
demonstrates that the MSCSS is accurate enough regarding
international building evaluation and design codes. This paper also
shows that the elasto-plastic dynamic analysis method is a reasonable
and reliable analysis method for structures subjected to strong
earthquake excitations and that the computed results are more precise.
Abstract: In diversity rich environments, such as in Ultra-
Wideband (UWB) applications, the a priori determination of the
number of strong diversity branches is difficult, because of the considerably large number of diversity paths, which are characterized
by a variety of power delay profiles (PDPs). Several
Rake implementations have been proposed in the past, in order to reduce the number of the estimated and combined paths. To this
aim, we introduce two adaptive Rake receivers, which combine
a subset of the resolvable paths considering simultaneously the
quality of both the total combining output signal-to-noise ratio (SNR) and the individual SNR of each path. These schemes achieve
better adaptation to channel conditions compared to other known receivers, without further increasing the complexity. Their performance
is evaluated in different practical UWB channels, whose models are based on extensive propagation measurements. The
proposed receivers compromise between the power consumption,
complexity and performance gain for the additional paths, resulting in important savings in power and computational resources.
Abstract: This study presents the improvement of thermal
performance of heat pipe using copper nanofluid with aqueous
solution of n-Butanol. The nanofluids kept in the suspension of
conventional fluids have the potential of superior heat transfer
capability than the conventional fluids due to their improved thermal
conductivity. In this work, the copper nanofluid which has a 40 nm
size with a concentration of 100 mg/lit is kept in the suspension of
the de-ionized (DI) water and an aqueous solution of n-Butanol and
these fluids are used as a working medium in the heat pipe. The study
discusses about the effect of heat pipe inclination, type of working
fluid and heat input on the thermal efficiency and thermal resistance.
The experimental results are evaluated in terms of its performance
metrics and are compared with that of DI water.
Abstract: This study was designed to formulate,
pharmaceutically evaluate a topical skin-care cream (w/o emulsion)
of Aloe Vera versus its vehicle (Base) as control and determine their
effects on Stratum Corneum (SC) water content and Transepidermal
water loss (TEWL). Base containing no extract and a Formulation
containing 3% concentrated extract of Aloe Vera was developed by
entrapping in the inner aqueous phase of w/o emulsion (cream).
Lemon oil was incorporated to improve the odor. Both the Base and
Formulation were stored at 8°C ±0.1°C (in refrigerator), 25°C±0.1°C,
40°C±0.1°C and 40°C± 0.1°C with 75% RH (in incubator) for a
period of 4 weeks to predict their stability. The evaluation parameters
consisted of color, smell, type of emulsion, phase separation,
electrical conductivity, centrifugation, liquefaction and pH. Both the
Base and Formulation were applied to the cheeks of 21 healthy
human volunteers for a period of 8 weeks Stratum corneum (SC)
water content and Transepidermal water loss (TEWL) were
monitored every week to measure any effect produced by these
topical creams. The expected organoleptic stability of creams was
achieved from 4 weeks in-vitro study period. Odor was disappeared
with the passage of time due to volatilization of lemon oil. Both the
Base and Formulation produced significant (p≤0.05) changes in
TEWL with respect to time. SC water content was significantly
(p≤0.05) increased by the Formulation while the Base has
insignificant (p 0.05) effects on SC water content. The newly
formulated cream of Aloe Vera, applied is suitable for improvement
and quantitative monitoring of skin hydration level (SC water
content/ moisturizing effects) and reducing TEWL in people with dry
skin.
Abstract: Size based filtration is one of the common methods
employed to isolate circulating tumor cells (CTCs) from whole
blood. It is well known that this method suffers from isolation
efficiency to purity tradeoff. However, this tradeoff is poorly
understood. In this paper, we present the design and manufacturing
of a special rectangular slit filter. The filter was designed to retain
maximal amounts of nucleated cells, while minimizing the pressure
on cells, thereby preserving their morphology. The key parameter,
namely, input pressure, was optimized to retain the maximal number
of tumor cells, whilst maximizing the depletion of normal blood cells
(red and white blood cells and platelets). Our results indicate that for
a slit geometry of 5 × 40 μm on a 13 mm circular membrane with a
fill factor of 21%, a pressure of 6.9 mBar yields the optimum for
maximizing isolation of MCF-7 and depletion of normal blood cells.
Abstract: In this paper, the criteria of Ψ-eventual stability have been established for generalized impulsive differential systems of multiple dependent variables. The sufficient conditions have been obtained using piecewise continuous Lyapunov function. An example is given to support our theoretical result.
Abstract: Virtual environment induces simulator sickness effect
for some users. The purpose of this research is to compare the
simulation sickness relative with parallax affect in one-screen and
three-screen HoloStageTM system, measured by Simulation Sickness
Questionnaire (SSQ). The results show the subjects tested in
three-screen has less sickness than one-screen and effect from the
Oculomotor (O) more than from the Disorientation (D) and more than
from the Nausea (N) or represented in O>D>N.
Abstract: It is important to give input information without other device in AR system. One solution is using hand for augmented reality application. Many researchers have proposed different solutions for hand interface in augmented reality. Analyze Histogram and connecting factor is can be example for that. Various Direction searching is one of robust way to recognition hand but it takes too much calculating time. And background should be distinguished with skin color. This paper proposes a hand tracking method to control the 3D object in augmented reality using depth device and skin color. Also in this work discussed relationship between several markers, which is based on relationship between camera and marker. One marker used for displaying virtual object and three markers for detecting hand gesture and manipulating the virtual object.
Abstract: In this paper a modified version NXM of traditional 5X5 playfair cipher is introduced which enable the user to encrypt message of any Natural language by taking appropriate size of the matrix depending upon the size of the natural language. 5X5 matrix has the capability of storing only 26 characters of English language and unable to store characters of any language having more than 26 characters. To overcome this limitation NXM matrix is introduced which solve this limitation. In this paper a special case of Urdu language is discussed. Where # is used for completing odd pair and * is used for repeating letters.
Abstract: Basic ingredients of concrete are cement, fine aggregate, coarse aggregate and water. To produce a concrete of certain specific properties, optimum proportion of these ingredients are mixed. The important factors which govern the mix design are grade of concrete, type of cement and size, shape and grading of aggregates. Concrete mix design method is based on experimentally evolved empirical relationship between the factors in the choice of mix design. Basic draw backs of this method are that it does not produce desired strength, calculations are cumbersome and a number of tables are to be referred for arriving at trial mix proportion moreover, the variation in attainment of desired strength is uncertain below the target strength and may even fail. To solve this problem, a lot of cubes of standard grades were prepared and attained 28 days strength determined for different combination of cement, fine aggregate, coarse aggregate and water. An artificial neural network (ANN) was prepared using these data. The input of ANN were grade of concrete, type of cement, size, shape and grading of aggregates and output were proportions of various ingredients. With the help of these inputs and outputs, ANN was trained using feed forward back proportion model. Finally trained ANN was validated, it was seen that it gave the result with/ error of maximum 4 to 5%. Hence, specific type of concrete can be prepared from given material properties and proportions of these materials can be quickly evaluated using the proposed ANN.