Abstract: This paper reports the tensile fracture location
characterizations of dissimilar friction stir welds between 5754
aluminium alloy and C11000 copper. The welds were produced using
three shoulder diameter tools; namely, 15, 18 and 25 mm by varying
the process parameters. The rotational speeds considered were 600,
950 and 1200 rpm while the feed rates employed were 50, 150 and
300 mm/min to represent the low, medium and high settings
respectively. The tensile fracture locations were evaluated using the
optical microscope to identify the fracture locations and were
characterized. It was observed that 70% of the tensile samples failed
in the Thermo Mechanically Affected Zone (TMAZ) of copper at the
weld joints. Further evaluation of the fracture surfaces of the pulled
tensile samples revealed that welds with low Ultimate Tensile
Strength either have defects or intermetallics present at their joint
interfaces.
Abstract: One of the major, difficult tasks in automated video
surveillance is the segmentation of relevant objects in the scene.
Current implementations often yield inconsistent results on average
from frame to frame when trying to differentiate partly occluding
objects. This paper presents an efficient block-based segmentation
algorithm which is capable of separating partly occluding objects and
detecting shadows. It has been proven to perform in real time with a
maximum duration of 47.48 ms per frame (for 8x8 blocks on a
720x576 image) with a true positive rate of 89.2%. The flexible
structure of the algorithm enables adaptations and improvements with
little effort. Most of the parameters correspond to relative differences
between quantities extracted from the image and should therefore not
depend on scene and lighting conditions. Thus presenting a
performance oriented segmentation algorithm which is applicable in
all critical real time scenarios.
Abstract: The ITE Project is a project that has 1800 km length
and across the Turkey's land through east to west. The project of
pipeline enters geographically from Iran to Doğubayazit (Turkey) in
the east, exits to Greece from Ipsala province of Turkey in the west.
This project is the one of the international projects in such scale that
provides the natural gas of Iran and Caspian Sea through the
European continent. In this investigation, some information will be
given about the methods used to verify the direction of the pipeline
and the technical properties of the results obtained. The cost of
project itself entirely depends on the direction of the pipeline which
would be as short as possible and the specifications of the land cover.
Production standards of 1/2000 scaled digital orthophoto and vectoral
maps as a results of the use of map production materials and methods
(such as high resolution satellite images, and digital aerial images
captured from digital aerial cameras), will also be given in this report.
According to Turkish national map production standards, TM
((Transversal Mercator, 3 degree) projection is used for large scale
map and UTM (Universal Transversal Mercator, 6 degree) is used for
small scale map production standards. Some information is also given
about the projection used in the ITE natural gas pipeline project.
Abstract: This paper describes the development of an electronic
instrument that looks like a flute, which is able to sense the basic musical notes being executed by a specific user. The principal function of the instrument is to teach how to play a flute. This device
will generate a significant academic impact, in a field of virtual reality interactive that combine art and technology. With this example is expected to contribute in research and implementation of teaching devices around the world.
Abstract: Despite of many scholars and practitioners recognize
the knowledge management implementation in an organizations but
insufficient attention has been paid by researchers to select suitable
knowledge portal system (KPS) selection. This study develops a
Multi Criteria Decision making model based on the fuzzy VIKOR
approach to help organizations in selecting KPS. The suitable portal
is the critical influential factors on the success of knowledge
management (KM) implementation in an organization.
Abstract: The p53 tumor suppressor gene plays two important
roles in genomic stability: blocking cell proliferation after DNA
damage until it has been repaired, and starting apoptosis if the
damage is too critical. Codon 72 exon4 polymorphism (Arg72Pro) of
the P53 gene has been implicated in cancer risk. Various studies have
been done to investigate the status of p53 at codon 72 for arginine
(Arg) and proline (Pro) alleles in different populations and also the
association of this codon 72 polymorphism with various tumors. Our
objective was to investigate the possible association between P53
Arg72Pro polymorphism and susceptibility to colorectal cancer
among Isfahan and Chaharmahal Va Bakhtiari (a part of south west
of Iran) population. We investigated the status of p53 at codon 72 for
Arg/Arg, Arg/Pro and Pro/Pro allele polymorphisms in blood
samples from 145 colorectal cancer patients and 140 controls by
Nested-PCR of p53 exon 4 and digestion with BstUI restriction
enzyme and the DNA fragments were then resolved by
electrophoresis in 2% agarose gel. The Pro allele was 279 bp, while
the Arg allele was restricted into two fragments of 160 and 119 bp.
Among the 145 colorectal cancer cases 49 cases (33.79%) were
homozygous for the Arg72 allele (Arg/Arg), 18 cases (12.41%) were
homozygous for the Pro72 allele (Pro/Pro) and 78 cases (53.8%)
found in heterozygous (Arg/Pro).
In conclusion, it can be said that p53Arg/Arg genotype may be
correlated with possible increased risk of this kind of cancers in south
west of Iran.
Abstract: In this paper, the effect of atmospheric turbulence on
bit error probability in free-space optical CDMA scheme with
Sequence Inverse Keyed (SIK) optical correlator receiver is analyzed.
Here Intensity Modulation scheme is considered for transmission.
The turbulence induced fading is described by the newly introduced
gamma-gamma pdf[1] as a tractable mathematical model for
atmospheric turbulence. Results are evaluated with Gold and Kasami
code & it is shown that Gold sequence can be used for more
efficient transmission than Kasami sequence in an atmospheric
turbulence channel.
Abstract: This paper presents the results of the experimental
tests of the cooling performance of a 12,000-Btu/h modified air
conditioner (referred to as M-AC) that use the ground as a heat sink
of a condenser. In the tests, cooling capacity of M-AC with an
optimal length of a condensing coil as well as life expectancy of
copper coil buried underground were investigated. The lengths of
copper coil fabricated and used as condenser coil of M-AC were set
at 67, 50, 40 and 30 m whereas that of a 12,000-Btu/h conventional
split-type air conditioner (referred to as C-AC) was about 22 m. The
results showed that the ground can absorb heat rejected from a
condenser of M-AC. The coefficient of performance (COP) of C-AC
was about 2.5 whereas those of M-AC were found to be higher. It
was found that the values of COP of M-AC with condensing coils of
67, 50 and 40 m long were about 6.9, 5.5 and 3.3, respectively, while
that of 30-m-long one was found to be about 2.1. The electrical
consumptions of M-AC were found lower than that of C-AC in the
range of 11.5 – 15.5%. Additionally, life expectancy of underground
condensing coil of M-AC was found to be over 7 years.
Abstract: In the past few years there is a change in the view of high performance applications and parallel computing. Initially such applications were targeted towards dedicated parallel machines. Recently trend is changing towards building meta-applications composed of several modules that exploit heterogeneous platforms and employ hybrid forms of parallelism. The aim of this paper is to propose a model of virtual parallel computing. Virtual parallel computing system provides a flexible object oriented software framework that makes it easy for programmers to write various parallel applications.
Abstract: The technology usages of high speed Internet leads to
establish and start new era of online education. With the
advancement of the information technology and communication
systems new opportunities have been created. This leads universities
to have various online education channels to meet the demand of
different learners- needs. One of these channels is M-learning, which
can be used to improve the online education environment. With using
such mobile technology in learning both students and instructors can
easily access educational courses anytime from anywhere. The paper
first presents literature about mobile learning and to what extent this
approach can be utilized to enhance the overall learning system. It
provides a comparison between mobile learning and traditional elearning
showing the wide array of benefits of the new generation of
technology. The possible challenges and potential advantages of Mlearning
in the online education system are also discussed.
Abstract: The purpose of this paper is to solve the problem of protecting aerial lines from high impedance faults (HIFs) in distribution systems. This investigation successfully applies 3I0 zero sequence current to solve HIF problems. The feature extraction system based on discrete wavelet transform (DWT) and the feature identification technique found on statistical confidence are then applied to discriminate effectively between the HIFs and the switch operations. Based on continuous wavelet transform (CWT) pattern recognition of HIFs is proposed, also. Staged fault testing results demonstrate that the proposed wavelet based algorithm is feasible performance well.
Abstract: A simple mobile engine-driven pneumatic paddy
collector made of locally available materials using local
manufacturing technology was designed, fabricated, and tested for
collecting and bagging of paddy dried on concrete pavement. The
pneumatic paddy collector had the following major components:
radial flat bladed type centrifugal fan, power transmission system,
bagging area, frame and the conveyance system. Results showed
significant differences on the collecting capacity, noise level, and fuel
consumption when rotational speed of the air mover shaft was varied.
Other parameters such as collecting efficiency, air velocity,
augmented cracked grain percentage, and germination rate were not
significantly affected by varying rotational speed of the air mover
shaft. The pneumatic paddy collector had a collecting efficiency of
99.33 % with a collecting capacity of 2685.00 kg/h at maximum
rotational speed of centrifugal fan shaft of about 4200 rpm. The
machine entailed an investment cost of P 62,829.25. The break-even
weight of paddy was 510,606.75 kg/yr at a collecting cost of 0.11
P/kg of paddy. Utilizing the machine for 400 hours per year
generated an income of P 23,887.73. The projected time needed to
recover cost of the machine based on 2685 kg/h collecting capacity
was 2.63 year.
Abstract: A traffic light gives security from traffic congestion,reducing the traffic jam, and organizing the traffic flow. Furthermore,increasing congestion level in public road networks is a growingproblem in many countries. Using Intelligent Transportation Systemsto provide emergency vehicles a green light at intersections canreduce driver confusion, reduce conflicts, and improve emergencyresponse times. Nowadays, the technology of wireless sensornetworks can solve many problems and can offer a good managementof the crossroad. In this paper, we develop a new approach based onthe technique of clustering and the graphical possibilistic fusionmodeling. So, the proposed model is elaborated in three phases. Thefirst one consists to decompose the environment into clusters,following by the fusion intra and inter clusters processes. Finally, wewill show some experimental results by simulation that proves theefficiency of our proposed approach.KeywordsTraffic light, Wireless sensor network, Controller,Possibilistic network/Bayesain network.
Abstract: There are several approaches for handling multiclass classification. Aside from one-against-one (OAO) and one-against-all (OAA), hierarchical classification technique is also commonly used. A binary classification tree is a hierarchical classification structure that breaks down a k-class problem into binary sub-problems, each solved by a binary classifier. In each node, a set of classes is divided into two subsets. A good class partition should be able to group similar classes together. Many algorithms measure similarity in term of distance between class centroids. Classes are grouped together by a clustering algorithm when distances between their centroids are small. In this paper, we present a binary classification tree with tuned observation-based clustering (BCT-TOB) that finds a class partition by performing clustering on observations instead of class centroids. A merging step is introduced to merge any insignificant class split. The experiment shows that performance of BCT-TOB is comparable to other algorithms.
Abstract: This study examines the possibility to apply the theory of multidimensional accounting (momentum accounting) in a Brazilian Navy-s Services Provider Military Organization (Organização Militar Prestadora de Serviços - OMPS). In general, the core of the said theory is the fact that Accounting does not recognize the inertia of transactions occurring in an entity, and that occur repeatedly in some cases, regardless of the implementation of new actions by its managers. The study evaluates the possibility of greater use of information recorded in the financial statements of the unit of analysis, within the strategic decisions of the organization. As a research strategy, we adopted the case study. The results infer that it is possible to use the theory in the context of a multidimensional OMPS, promoting useful information for decision-making and thereby contributing to the strengthening of the necessary alignment of its administration with the current desires of the Brazilian society.
Abstract: This study was carried out in Ankara, the capital city of Turkey, in order to determine how people living in the slums of Ankara benefit from educational equality. Within the scope of the research, interviews were made with 64 families whose children have been getting education from the primary schools of these parts and the data of the study was collected by the researcher. The results of the research demonstrate that the children getting education in the slums of Ankara can not experience educational equality and justice. The results of this study show that the opportunities of the schools in the slums of Ankara are very limited, so the individuals in these districts can not equally benefit from the education. The families are aware of the problem they are faced with. KeywordsDiscrimination, inequality, primary education, slums of Turkey.
Abstract: Groundwater has become the most dependable source
of fresh water for agriculture, domestic and industrial uses in the past
few decades. This wide use of groundwater if left uncontrolled and
unseen will lead to overexploitation causing sea water intrusion in the
coastal areas and illegal water marketing. Several Policies and Acts
have been enacted to regulate and manage the use of this valuable
resource. In spite of this the over extraction of groundwater beyond
the recharging capacity of aquifers and depletion in the quality of
groundwater is continuing. The current study aims at reviewing the
Acts and Policies existing in the State of Tamil Nadu and in the
National level regarding groundwater regulation and management.
Further an analysis is made on the rights associated with the usage of
groundwater resources and the gaps in these policies have been
analyzed. Some suggestions are made to reform the existing
groundwater policies for better management and regulation of the
resource.
Abstract: The thermal, epithermal and fast fluxes were
calculated for three irradiation channels at Egypt Second Research
Reactor (ETRR-2) using CITVAP code. The validity of the
calculations was verified by experimental measurements. There are
some deviations between measurements and calculations. This is due
to approximations in the calculation models used, homogenization of
regions, condensation of energy groups and uncertainty in nuclear
data used. Neutron flux data for the three irradiation channels are
now available. This would enable predicting the irradiation
conditions needed for future radioisotope production.
Abstract: The power consumption of an Optical Packet Switch
equipped with SOA technology based Spanke switching fabric is
evaluated. Sophisticated analytical models are introduced to evaluate
the power consumption versus the offered traffic, the main
switch parameters, and the used device characteristics. The impact
of Amplifier Spontaneous Emission (ASE) noise generated by a
transmission system on the power consumption is investigated. As
a matter of example for 32×32 switches supporting 64 wavelengths
and offered traffic equal to 0,8, the average energy consumption per
bit is 5, 07 · 10-2 nJ/bit and increases if ASE noise introduced by
the transmission systems is increased.
Abstract: Buildings and associated construction methods have a significant impact on the environment. As construction activity increases in Kuwait, there is a need to create design and construction strategies which will minimize the environmental impact of new buildings. Green construction is a design philosophy intended to improve the sustainability of construction by the minimization of resource depletion and CO2 emissions throughout the life cycle of buildings. This paper presents and discusses the results of a survey that was conducted in Kuwait, with the objective of investigating the awareness of developers and other stakeholders regarding their understanding and use of green construction strategies. The results of the survey demonstrate that whilst there seems to be a reasonable level of awareness amongst the stakeholders, this awareness is not currently well reflected in the design and construction practices actually being applied. It is therefore concluded is there is a pressing need for intervention from Government in order that the use of sustainable green design and construction strategies becomes the norm in Kuwait.