Abstract: A very large percentage of bridge failures are attributed to scouring around bridge piers and this directly influences public safety. Experiments are carried out in a 12-m long rectangular open channel flume made of transparent tempered glass. A 300 mm thick bed made up of sand particles is leveled horizontally to create the test bed and a 50 mm hollow plastic cylinder is used as a model bridge pier. Tests are carried out with varying flow depths and velocities. Data points of various scour parameters such as scour depth, width, and length are collected based on different flow conditions and visual observations of changes in the stream bed downstream the bridge pier are also made as the scour progresses. Result shows that all three major flow characteristics (flow depth, Froude number and densimetric Froude number) have one way or other affect the scour profile.
Abstract: Sudden change of bed condition is frequent in open channel flow. Change of bed condition affects the turbulence characteristics in both streamwise and wall-normal direction. Understanding the turbulence intensity in open channel flow is of vital importance to the modeling of sediment transport and resuspension, bed formation, entrainment, and the exchange of energy and momentum. A comprehensive study was carried out to understand the extent of the effect of Reynolds number and bed roughness on different turbulence characteristics in an open channel flow. Four different bed conditions (impervious smooth bed, impervious continuous rough bed, pervious rough sand bed, and impervious distributed roughness) and two different Reynolds numbers were adopted for this cause. The effect of bed roughness on different turbulence characteristics is seen to be prevalent for most of the flow depth. Effect of Reynolds number on different turbulence characteristics is also evident for flow over different bed, but the extent varies on bed condition. Although the same sand grain is used to create the different rough bed conditions, the difference in turbulence characteristics is an indication that specific geometry of the roughness has an influence on turbulence characteristics. Roughness increases the contribution of the extreme turbulent events which produces very large instantaneous Reynolds shear stress and can potentially influence the sediment transport, resuspension of pollutant from bed and alter the nutrient composition, which eventually affect the sustainability of benthic organisms.
Abstract: The present study was carried out to understand the extent of effect of roughness and Reynolds number in open channel flow (OCF). To this extent, four different types of bed surface conditions consisting smooth, distributed roughness, continuous roughness, natural sand bed and two different Reynolds number for each bed surfaces were adopted in this study. Particular attention was given on mean velocity, turbulence intensity, Reynolds shear stress, correlation, higher order moments and quadrant analysis. Further, the extent of influence of roughness and Reynolds number in the depth-wise direction also studied. Increasing Reynolds shear stress near rough beds are noticed due to arrays of discrete roughness elements and flow over these elements generating a series of wakes which contributes to the generation of significantly higher Reynolds shear stress.
Abstract: An experimental study with four different types of bed
conditions was carried out to understand the effect of roughness in
open channel flow at two different Reynolds numbers. The bed
conditions include a smooth surface and three different roughness
conditions, which were generated using sand grains with a median
diameter of 2.46 mm. The three rough conditions include a surface
with distributed roughness, a surface with continuously distributed
roughness and a sand bed with a permeable interface. A commercial
two-component fibre-optic LDA system was used to conduct the
velocity measurements. The variables of interest include the mean
velocity, turbulence intensity, correlation between the streamwise and
the wall normal turbulence, Reynolds shear stress and velocity triple
products. Quadrant decomposition was used to extract the magnitude
of the Reynolds shear stress of the turbulent bursting events. The
effect of roughness was evident throughout the flow depth. The
results show that distributed roughness has the greatest roughness
effect followed by the sand bed and the continuous roughness.
Compared to the smooth bed, the streamwise turbulence intensity
reduces but the vertical turbulence intensity increases at a location
very close to the bed due to the introduction of roughness. Although
the same sand grain is used to create the three different rough bed
conditions, the difference in the turbulence intensity is an indication
that the specific geometry of the roughness has an influence on
turbulence structure.
Abstract: Series of laboratory tests were carried out to study the
extent of scour caused by a three-dimensional wall jets exiting from a
square cross-section nozzle and into a non-cohesive sand beds.
Previous observations have indicated that the effect of the tail water
depth was significant for densimetric Froude number greater than ten.
However, the present results indicate that the cut off value could be
lower depending on the value of grain size-to-nozzle width ratio.
Numbers of equations are drawn out for a better scaling of numerous
scour parameters. Also suggested the empirical prediction of scour to
predict the scour centre line profile and plan view of scour profile at
any particular time.