Abstract: This paper presents the results of thermo-mechanical
characterization of Glass/Epoxy composite specimens using Infrared
Thermography technique. The specimens used for the study were
fabricated in-house with three different lay-up sequences and tested
on a servo hydraulic machine under uni-axial loading. Infrared
Camera was used for on-line monitoring surface temperature changes
of composite specimens during tensile deformation.
Experimental results showed that thermomechanical
characteristics of each type of specimens were distinct. Temperature
was found to be decreasing linearly with increasing tensile stress in
the elastic region due to thermo-elastic effect. Yield point could be
observed by monitoring the change in temperature profile during
tensile testing and this value could be correlated with the results
obtained from stress-strain response. The extent of prior plastic
deformation in the post-yield region influenced the slopes of
temperature response during tensile loading. Partial unloading and
reloading of specimens post-yield results in change in slope in elastic
and plastic regions of composite specimens.
Abstract: This study deals with the experimental investigation
and theoretical modeling of Semi crystalline polymeric materials with
a rubbery amorphous phase (HDPE) subjected to a uniaxial cyclic
tests with various maximum strain levels, even at large deformation.
Each cycle is loaded in tension up to certain maximum strain and
then unloaded down to zero stress with N number of cycles. This
work is focuses on the measure of the volume strain due to the
phenomena of damage during this kind of tests. On the basis of
thermodynamics of relaxation processes, a constitutive model for
large strain deformation has been developed, taking into account the
damage effect, to predict the complex elasto-viscoelastic-viscoplastic
behavior of material. A direct comparison between the model
predictions and the experimental data show that the model accurately
captures the material response. The model is also capable of
predicting the influence damage causing volume variation.
Abstract: The performance of sensor-less controlled induction
motor drive depends on the accuracy of the estimated speed.
Conventional estimation techniques being mathematically complex
require more execution time resulting in poor dynamic response. The
nonlinear mapping capability and powerful learning algorithms of
neural network provides a promising alternative for on-line speed
estimation. The on-line speed estimator requires the NN model to be
accurate, simpler in design, structurally compact and computationally
less complex to ensure faster execution and effective control in real
time implementation. This in turn to a large extent depends on the
type of Neural Architecture. This paper investigates three types of
neural architectures for on-line speed estimation and their
performance is compared in terms of accuracy, structural
compactness, computational complexity and execution time. The
suitable neural architecture for on-line speed estimation is identified
and the promising results obtained are presented.
Abstract: A DC-to-DC converter for applications involving a
source with widely varying voltage conditions with loads requiring
constant voltage from full load down to no load is presented.
The switching regulator considered is a Buck converter with Pulse
Skipping Modulation control whereby pulses applied to the switch
are blocked or released on output voltage crossing a predetermined
value. Results of the study on the performance of regulator circuit
are presented. The regulator regulates over a wide input voltage range
with slightly higher ripple content and good transient response. Input
current spectrum indicates a good EMI performance with crowding
of components at low frequency range.
Abstract: In Indonesia, goat milk is often consumed and
believed as anti-allergy. The objective of this research was to study
the effect of goat milk and their fractions (casein and whey)
supplementation on total serum IgE concentrations and leukocytes
count in rat sensitized with contact allergen dinitrochlorobenzene
(DNCB). Female Wistar rats 6-8 weeks old were divided into four
groups: 1) whey, 2) casein, 3) whole milk supplementation and 4)
phosphate-buffered saline/PBS (control). The results showed that
supplementation of goat milk on rats did not affects on total serum
IgE concentrations and number of leukocytes. After sensitized with
DNCB, the monocyte percentage in rats was higher (P
Abstract: This paper presents a new method to detect high impedance faults in radial distribution systems. Magnitudes of third and fifth harmonic components of voltages and currents are used as a feature vector for fault discrimination. The proposed methodology uses a learning vector quantization (LVQ) neural network as a classifier for identifying high impedance arc-type faults. The network learns from the data obtained from simulation of a simple radial system under different fault and system conditions. Compared to a feed-forward neural network, a properly tuned LVQ network gives quicker response.
Abstract: An influence of intranasal combined injection of live
cold-adapted influenza vaccine with chitosan derivatives as adjuvants
on the subpopulation structure of mononuclear leukocytes of mouse
spleen which reflects the orientation of the immune response was
studied. It is found that the inclusion of chitosan preparations
promotes activation of cellular-level of immune response.
Abstract: In this study, the effect of L-arginine was examined at the neuromuscular junction of the chick biventer cervicis muscle. LArginine at 500 μg/ ml, decreased twitch response to electerical stimulation, and produced rightward shift of the dose- response curve for acetylcholine or carbachol. L-Arginine at 1000μg/ ml produced a strong shift to the right of the dose – response curve for acetylcholine or carbachol with a reduction in the efficacy. The inhibitory effect of L-arginine on the twitch response was blocked by caffeine (200μg/ ml). NO levels were also measured in the chick biventer cervicis muscle homogenates, using spectrophotometric method for the direct detection of NO, nitrite and nitrate. Total nitrite (nitrite + nitrate) was measured by a spectrophotometer at 540 nm after the conversion of nitrate to nitrite by copperized cadmium granules. NO levels were found to be significantly increased in concentrations 500 and 1000μg/ ml of L-arginine in comparison with the control group (p
Abstract: The authors present optimization parameters of rotary
positioner controller in hard disk drive servo track writing process
using coefficient diagram method; CDM. Due to estimation
parameters in PI Positioning Control System by expected ratio
method cannot meet the required specification of response
effectively, we suggest coefficient diagram method for defining
controller parameters under the requirement of the system. Finally,
the simulation results show that our proposed method can improve
the problem in tuning parameter of rotary positioner controller. It is
satisfied specification of performance of control system. Furthermore,
it is very convenient as a fast adjustment damping ratio as well as a
high speed response.
Abstract: A novel three-phase active power filter (APF) circuit with photovoltaic (PV) system to improve the quality of service and to reduce the capacity of energy storage capacitor is presented. The energy balance concept and sampling technique were used to simplify the calculation algorithm for the required utility source current and to control the voltage of the energy storage capacitor. The feasibility was verified by using the Pspice simulations and experiments. When the APF mode was used during non-operational period, not only the utilization rate, power factor and power quality could be improved, but also the capacity of energy storage capacitor could sparing. As the results, the advantages of the APF circuit are simplicity of control circuits, low cost, and good transient response.
Abstract: This paper presents a speed sensorless direct torque
control scheme using space vector modulation (DTC-SVM) for
permanent magnet synchronous motor (PMSM) drive based a Model
Reference Adaptive System (MRAS) algorithm and stator resistance
estimator. The MRAS is utilized to estimate speed and stator
resistance and compensate the effects of parameter variation on stator
resistance, which makes flux and torque estimation more accurate
and insensitive to parameter variation. In other hand the use of SVM
method reduces the torque ripple while achieving a good dynamic
response. Simulation results are presented and show the effectiveness
of the proposed method.
Abstract: Due to increased number of terrorist attacks in recent years, loads induced by explosions need to be incorporated in building designs. For safer performance of a structure, its foundation should have sufficient strength and stability. Therefore, prior to any reconstruction or rehabilitation of a building subjected to blast, it is important to examine adverse effects on the foundation caused by blast induced ground shocks. This paper evaluates the effects of a buried explosion on a pile foundation. It treats the dynamic response of the pile in saturated sand, using explicit dynamic nonlinear finite element software LS-DYNA. The blast induced wave propagation in the soil and the horizontal deformation of pile are presented and the results are discussed. Further, a parametric study is carried out to evaluate the effect of varying the explosive shape on the pile response. This information can be used to evaluate the vulnerability of piled foundations to credible blast events as well as develop guidance for their design.
Abstract: En bloc assumes modeling all phases of the orthostatic test with the only one mathematical model, which allows the complex parametric view of orthostatic response. The work presents the implementation of a mathematical model for processing of the measurements of systolic, diastolic blood pressure and heart rate performed on volunteers during orthostatic test. The original assumption of model hypothesis that every postural change means only one Stressor, did not complying with the measurements of physiological circulation factor-time profiles. Results of the identification support the hypothesis that second postural change of orthostatic test causes induced Stressors, with the observation of a physiological regulation mechanism. Maximal demonstrations are on the heart rate and diastolic blood pressure-time profile, minimal are for the measurements of the systolic blood pressure. Presented study gives a new view on orthostatic test with impact on clinical practice.
Abstract: The Chichiawan stream in the Wulin catchment in
Taiwan is the natural habitat of Formosan landlocked salmon. Human
and agriculture activities gradually worsen water quality and impact
the fish habitat negatively. To protect and manage Formosan
landlocked salmon habitat, it is important to understand a variety
land-uses affect on the watershed responses to storms. This study
discusses watershed responses to the dry-day before a storm event and
a variety of land-uses in the Wulin catchment. Under the land-use
planning in the Wulin catchment, the peak flows during typhoon
events do not have noticeable difference. However, the nutrient
exports can be highly reduced under the strategies of restraining
agriculture activities. Due to the higher affinity of P for soil than that
of N, the exports of TN from overall Wuling catchment were much
greater than Ortho-P. Agriculture mainly centralized in subbasin A,
which is the important source of nutrients in nonpoint source discharge.
The subbasin A supplied about 26% of the TN and 32% of the Ortho-P
discharge in 2004, despite the fact it only covers 19% area of the
Wuling catchment. The subbasin analysis displayed that the
agricultural subbasin A exports higher nutrients per unit area than
other forest subbasins. Additionally, the agricultural subbasin A
contributed a higher percentage to total Ortho-P exports compares to
TN. The results of subbasin analysis might imply the transport of
Ortho-P was similar to the particulate matter which was mainly
influenced by the runoff and affected by the desorption from soil
particles while the TN (dominated as nitrate-N) was mainly influenced
by base-flow.
Abstract: This paper considers the control of the longitudinal
flight dynamics of an F-16 aircraft. The primary design objective
is model-following of the pitch rate q, which is the preferred
system for aircraft approach and landing. Regulation of the aircraft
velocity V (or the Mach-hold autopilot) is also considered, but
as a secondary objective. The problem is challenging because the
system is nonlinear, and also non-affine in the input. A sliding
mode controller is designed for the pitch rate, that exploits the
modal decomposition of the linearized dynamics into its short-period
and phugoid approximations. The inherent robustness of the SMC
design provides a convenient way to design controllers without gain
scheduling, with a steady-state response that is comparable to that
of a conventional polynomial based gain-scheduled approach with
integral control, but with improved transient performance. Integral
action is introduced in the sliding mode design using the recently
developed technique of “conditional integrators", and it is shown that
robust regulation is achieved with asymptotically constant exogenous
signals, without degrading the transient response. Through extensive
simulation on the nonlinear multiple-input multiple-output (MIMO)
longitudinal model of the F-16 aircraft, it is shown that the conditional
integrator design outperforms the one based on the conventional linear
control, without requiring any scheduling.
Abstract: The vibrations produced by a single point defect on
various parts of the bearing under constant radial load are predicted
by using a theoretical model. The model includes variation in the
response due to the effect of bearing dimensions, rotating frequency
distribution of load. The excitation forces are generated when the
defects on the races strike to rolling elements. In case of the outer
ring defect, the pulses generated are with periodicity of outer ring
defect frequency where as for inner ring defect, the pulses are with
periodicity of inner ring defect frequency. The effort has been carried
out in preparing the physical model of the system. Different defect
frequencies are obtained and are used to find out the amplitudes of
the vibration due to excitation of the bearing parts. Increase in the
radial load or severity of the defect produces a significant change in
bearing signature characteristics.
Abstract: This paper presents the approach to design the Auto-
Tuning PID controller for interactive Water Level Process using
integral step response. The Integral Step Response (ISR) is the
method to model a dynamic process which can be done easily,
conveniently and very efficiently. Therefore this method is advantage
for design the auto tune PID controller. Our scheme uses the root
locus technique to design PID controller. In this paper MATLAB is
used for modeling and testing of the control system. The
experimental results of the interacting water level process can be
satisfyingly illustrated the transient response and the steady state
response.
Abstract: The Institute of Product Development is dealing
with the development, design and dimensioning of micro components
and systems as a member of the Collaborative Research
Centre 499 “Design, Production and Quality Assurance of
Molded micro components made of Metallic and Ceramic Materials".
Because of technological restrictions in the miniaturization
of conventional manufacturing techniques, shape and
material deviations cannot be scaled down in the same proportion
as the micro parts, rendering components with relatively
wide tolerance fields. Systems that include such components
should be designed with this particularity in mind, often requiring
large clearance. On the end, the output of such systems
results variable and prone to dynamical instability. To save
production time and resources, every study of these effects
should happen early in the product development process and
base on computer simulation to avoid costly prototypes. A
suitable method is proposed here and exemplary applied to a
micro technology demonstrator developed by the CRC499. It
consists of a one stage planetary gear train in a sun-planet-ring
configuration, with input through the sun gear and output
through the carrier. The simulation procedure relies on ordinary
Multi Body Simulation methods and subsequently adds
other techniques to further investigate details of the system-s
behavior and to predict its response. The selection of the relevant
parameters and output functions followed the engineering
standards for regular sized gear trains. The first step is to
quantify the variability and to reveal the most critical points of
the system, performed through a whole-mechanism Sensitivity
Analysis. Due to the lack of previous knowledge about the system-s
behavior, different DOE methods involving small and
large amount of experiments were selected to perform the SA.
In this particular case the parameter space can be divided into
two well defined groups, one of them containing the gear-s profile
information and the other the components- spatial location.
This has been exploited to explore the different DOE techniques
more promptly. A reduced set of parameters is derived for
further investigation and to feed the final optimization process,
whether as optimization parameters or as external perturbation
collective. The 10 most relevant perturbation factors and 4 to 6
prospective variable parameters are considered in a new, simplified
model. All of the parameters are affected by the mentioned
production variability. The objective functions of interest
are based on scalar output-s variability measures, so the
problem becomes an optimization under robustness and reliability constrains. The study shows an initial step on the development
path of a method to design and optimize complex micro
mechanisms composed of wide tolerated elements accounting
for the robustness and reliability of the systems- output.
Abstract: This paper investigated the organizational
innovativeness of public listed housing developers in Malaysia. We
conceptualized organizational innovativeness as a multi-dimensional
construct consisting of 5 dimensions: market innovativeness, product
innovativeness, process innovativeness, behavior innovativeness and
strategic innovativeness. We carried out questionnaire survey with all
accessible public listed developers in Malaysia and received a 56
percent response. We found that the innovativeness of public listed
housing developers is low. The study extends the knowledge on
innovativeness theory by using a multi-dimensional contructs to
conceptualize the innovativeness of public listed housing developers
in Malaysia where all this while most studies focused on single
dimensional construct of innovativeness. The paper ends by
providing some explanations for the results.
Abstract: Shape memory alloy (SMA) actuators have found a
wide range of applications due to their unique properties such as high
force, small size, lightweight and silent operation. This paper presents
the development of compact (SMA) actuator and cooling system in
one unit. This actuator is developed for multi-fingered hand. It
consists of nickel-titanium (Nitinol) SMA wires in compact forming.
The new arrangement insulates SMA wires from the human body by
housing it in a heat sink and uses a thermoelectric device for rejecting
heat to improve the actuator performance. The study uses
optimization methods for selecting the SMA wires geometrical
parameters and the material of a heat sink. The experimental work
implements the actuator prototype and measures its response.