Abstract: In this study, ZnO nano rods and ZnO ultrafine particles were synthesized by Gel-casting method. The synthesized ZnO powder has a hexagonal zincite structure. The ZnO aggregates with rod-like morphology are typically 1.4 μm in length and 120 nm in diameter, which consist of many small nanocrystals with diameters of 10 nm. Longer wires connected by many hexahedral ZnO nanocrystals were obtained after calcinations at the temperature over 600° C.The crystalline structures and morphologies of the powder have been characterized by X-ray diffraction(XRD) and Scaning electron microscopy (SEM).The result shows that the different preparation conditions such as concentration H2O, calcinations time and calcinations temperature have a lot of influences upon the properties of nano ZnO powders, an increase in the temperature of the calcinations results in an increase of the grain size and also the increase of the calcinations time in high temperature makes the size of the grains bigger. The existences of extra watter prevent nano grains from improving like rod morphology. We have obtained the smallest grain size of ZnO powder by controlling the process conditions. Finally In a suitable condition, a novel nanostructure, namely bi-rod-like ZnO nano rods was found which is different from known ZnO nanostructures.
Abstract: This study fabricates p-type Ni1−xO:Li/n-Si heterojunction solar cells (P+/n HJSCs) by using radio frequency (RF) magnetron sputtering and investigates the effect of substrate temperature on photovoltaic cell properties. Grazing incidence x-ray diffraction, four point probe, and ultraviolet-visible-near infrared discover the optoelectrical properties of p-Ni1-xO thin films. The results show that p-Ni1-xO thin films deposited at 300 oC has the highest grain size (22.4 nm), average visible transmittance (~42%), and electrical resistivity (2.7 Ωcm). However, the conversion efficiency of cell is shown only 2.33% which is lower than the cell (3.39%) fabricated at room temperature. This result can be mainly attributed to interfacial layer thickness (SiOx) reduces from 2.35 nm to 1.70 nm, as verified by high-resolution transmission electron microscopy.
Abstract: Safety, river environment, and sediment utilization are the elements of the target of sediment management. As a change in an element by sediment management, may affect the other two elements, and the priority among three elements depends on stakeholders. It is necessary to develop a method to evaluate the effect of sediment management on each element and an integrated evaluation method for socio-economic effect. In this study, taking Mount Merapi basin as an investigation field, the method for an active volcanic basin was developed. An integrated evaluation method for sediment management was discussed from a socio-economic point on safety, environment, and sediment utilization and a case study of sediment management was evaluated by means of this method. To evaluate the effect of sediment management, some parameters on safety, utilization, and environment have been introduced. From a utilization point of view, job opportunity, additional income of local people, and tax income to local government were used to evaluate the effectiveness of sediment management. The risk degree of river infrastructure was used to describe the effect of sediment management on a safety aspect. To evaluate the effects of sediment management on environment, the mean diameter of grain size distribution of riverbed surface was used. On the coordinate system designating these elements, the direction of change in basin condition by sediment management can be predicted, so that the most preferable sediment management can be decided. The results indicate that the cases of sediment management tend to give the negative impacts on sediment utilization. However, these sediment managements will give positive impacts on safety and environment condition. Evaluation result from a social-economic point of view shows that the case study of sediment management reduces job opportunity and additional income for inhabitants as well as tax income for government. Therefore, it is necessary to make another policy for creating job opportunity for inhabitants to support these sediment managements.
Abstract: (Bi0.5Na0.5)TiO3 doped with 8 mol % BaTiO3 powder
(BNT-BT0.08), prepared by sol-gel method was compacted and
sintered by Spark Plasma Sintering (SPS) process. The influence of
SPS temperature on the densification of BNT-BT0.08 ceramic was
investigated. Starting from sol-gel nanopowder of BNT-BT
containing 8 mol % BaTiO3 with an average particles size of about
30 nm, were obtained ceramics with density around 98 % of the
theoretical density value when the SPS temperature used was about
850 °C. The average grain size of the resulting ceramics was 80 nm.
The BNT-BT0.08 ceramic sample obtained by SPS method has shown
good electric properties at various frequencies.
Abstract: The gel-supported precipitation (GSP) process can be
used to make spherical particles (spherules) of nuclear fuel,
particularly for very high temperature reactors (VHTR) and even for
implementing the process called SPHEREPAC. In these different
cases, the main characteristics are the sphericity of the particles to be
manufactured and the control over their grain size. Nonetheless,
depending on the specifications defined for these spherical particles,
the GSP process has intrinsic limits, particularly when fabricating
very small particles. This paper describes the use of secondary
fragmentation (water, water/PVA and uranyl nitrate) on solid
surfaces under varying temperature and vibration conditions to assess
the relevance of using this new technique to manufacture very small
spherical particles by means of a modified GSP process. The
fragmentation mechanisms are monitored and analysed, before the
trends for its subsequent optimised application are described.
Abstract: This study investigated the effect of cross sectional
geometry on sediment transport rate. The processes of sediment
transport are generally associated to environmental management,
such as pollution caused by the forming of suspended sediment in the
channel network of a watershed and preserving physical habitats and
native vegetations, and engineering applications, such as the
influence of sediment transport on hydraulic structures and flood
control design. Many equations have been proposed for computing
the sediment transport, the influence of many variables on sediment
transport has been understood; however, the effect of other variables
still requires further research. For open channel flow, sediment
transport capacity is recognized to be a function of friction slope,
flow velocity, grain size, grain roughness and form roughness, the
hydraulic radius of the bed section and the type and quantity of
vegetation cover. The effect of cross sectional geometry of the
channel on sediment transport is one of the variables that need
additional investigation. The width-depth ratio (W/d) is a
comparative indicator of the channel shape. The width is the total
distance across the channel and the depth is the mean depth of the
channel. The mean depth is best calculated as total cross-sectional
area divided by the top width. Channels with high W/d ratios tend to
be shallow and wide, while channels with low (W/d) ratios tend to be
narrow and deep. In this study, the effects of the width-depth ratio on
sediment transport was demonstrated theoretically by inserting the
shape factor in sediment continuity equation and analytically by
utilizing the field data sets for Yalobusha River. It was found by
utilizing the two approaches as a width-depth ratio increases the
sediment transport decreases.
Abstract: Sediment loads transfer in hydraulic installations and their consequences for the O&M of modern canal systems is emerging as one of the most important considerations in hydraulic engineering projects apriticularly those which are inteded to feed the irrigation and draiange schemes of large command areas such as the Dez and Mogahn in Iran.. The aim of this paper is to investigate the applicability of the vortex tube as a viable means of extracting sediment loads entering the canal systems in general and the water inatke structures in particulars. The Western conveyance canal of the Dez Diversion weir which feeds the Karkheh Flood Plain in Sothwestern Dezful has been used as the case study using the data from the Dastmashan Hydrometric Station. The SHARC software has been used as an analytical framework to interprete the data. Results show that given the grain size D50 and the canal turbulence the adaption length from the beginning of the canal and after the diversion dam is estimated at 477 m, a point which is suitable for laying the vortex tube.
Abstract: Low oxygen content vanadium powder was
prepared by hydrogenation dehydrogenization (HDH). The
effect of purification treatment on hydrogen absorption kinetics
of dendritic vanadium was tested, and the effects of milling
technique on powder yield and grain size were studied. The
crystal phase, oxygen and nitrgen content, and grain size of
prepared powder were characterized and analyzed by X-ray
diffraction (XRD), oxygen and nitrogen analyzer and grain size
analyzer. The results show that the alkaline cleaning can
improve the hydrogen absorption of vanadium. The yield of
vanadium hydride powder can reach as high as 90% by 4h
ball-milling, The resultant product also have an oxygen content
less than 600μg/g, and the grain size is smaller than 37μm.
Meanwhile, the XRD results show that the phase of hydride
vanadium powder is mainly VH0.81. After a hydrogen
desorption treatment in vacuum at 700Ôäâ, the phase of the
powder converts into V and a little of V2H.
Abstract: Equal Channel Angular Pressing (ECAP) is currently
being widely investigated because of its potential to produce ultrafine
grained microstructures in metals and alloys. A sound
knowledge of the plastic deformation and strain distribution is
necessary for understanding the relationships between strain
inhomogeneity and die geometry. Considerable research has been
reported on finite element analysis of this process, assuming threedimensional
plane strain condition. However, the two-dimensional
models are not suitable due to the geometry of the dies, especially in
cylindrical ones. In the present work, three-dimensional simulation of
ECAP process was carried out for six outer corner radii (sharp to 10
mm in steps of 2 mm), with channel angle 105¶Çü▒, for strain hardening
aluminium alloy (AA 6101) using ABAQUS/Standard software.
Strain inhomogeneity is presented and discussed for all cases. Pattern
of strain variation along selected radial lines in the body of the workpiece
is presented. It is found from the results that the outer corner
has a significant influence on the strain distribution in the body of
work-piece. Based on inhomogeneity and average strain criteria,
there is an optimum outer corner radius.
Abstract: Sedimentation formation is a complex hydraulic phenomenon that has emerged as a major operational and maintenance consideration in modern hydraulic engineering in general and river engineering in particular. Sediments accumulation along the river course and their eventual storage in a form of islands affect water intake in the canal systems that are fed by the storage reservoirs. Without proper management, sediment transport can lead to major operational challenges in water distribution system of arid regions like the Dez and Hamidieh command areas. The paper aims to investigate sedimentation in the Western Canal of Dez Diversion Weir using the SHARC model and compare the results with the two intake structures of the Hamidieh dam in Iran using SSIIM model. The objective was to identify the factors which influence the process, check reliability of outcome and provide ways in which to mitigate the implications on operation and maintenance of the structures. Results estimated sand and silt bed loads concentrations to be 193 ppm and 827ppm respectively. This followed ,ore or less similar pattern in Hamidieh where the sediment formation impeded water intake in the canal system. Given the available data on average annual bed loads and average suspended sediment loads of 165ppm and 837ppm in the Dez, there was a significant statistical difference (16%) between the sand grains, whereas no significant difference (1.2%) was find in the silt grain sizes. One explanation for such finding being that along the 6 Km river course there was considerable meandering effects which explains recent shift in the hydraulic behavior along the stream course under investigation. The sand concentration in downstream relative to present state of the canal showed a steep descending curve. Sediment trapping on the other hand indicated a steep ascending curve. These occurred because the diversion weir was not considered in the simulation model. The comparative study showed very close similarities in the results which explains the fact that both software can be used as accurate and reliable analytical tools for simulation of the sedimentation in hydraulic engineering.
Abstract: The ferroelectric behavior of barium strontium
titanate (BST) in thin film form has been investigated in order to
study the possibility of using BST for ferroelectric gate-field effect
transistor (FeFET) for memory devices application. BST thin films
have been fabricated as Al/BST/Pt/SiO2/Si-gate configuration. The
variation of the dielectric constant (ε) and tan δ with frequency have
been studied to ensure the dielectric quality of the material. The
results show that at low frequencies, ε increases as the Ba content
increases, whereas at high frequencies, it shows the opposite
variation, which is attributed to the dipole dynamics. tan δ shows low
values with a peak at the mid-frequency range. The ferroelectric
behavior of the Al/BST/Pt/SiO2/Si has been investigated using C-V
characteristics. The results show that the strength of the ferroelectric
hysteresis loop increases as the Ba content increases; this is attributed
to the grain size and dipole dynamics effect.
Abstract: Nano sized zirconium dioxide in monoclinic phase (m-ZrO2) has been synthesized in pure form through co-precipitation processing at different calcination temperatures and has been characterized by several techniques such as XRD, FT-IR, UV-Vis Spectroscopy and SEM. The dielectric and capacitance values of the pelletized samples have been examined at room temperature as the functions of frequency. The higher dielectric constant value of the sample having larger grain size proves the strong influence of grain size on the dielectric constant.
Abstract: Metallic micro parts are playing an important role in micro-fabrication industry. Recently, we have demonstrated a new deformation mechanism for micro-formability of polycrystalline materials. Different depressed micro-features smaller than the grain size have been successfully fabricated on 6061 aluminum alloy (AA6061) substrates with good fidelity. To further verify this proposed deformation mechanism that grain size is not a limiting factor, we demonstrate here that in addition of depressed features, protruded micro-features on a polycrystalline substrate can similarly be fabricated.
Abstract: The distribution, enrichment, accumulation, and potential ecological risk of copper (Cu) in the surface sediments of northern Kaohsiung Harbor, Taiwan were investigated. Sediment samples from 12 locations of northern Kaohsiung Harbor were collected and characterized for Cu, aluminum, water content, organic matter, total nitrogen, total phosphorous, total grease and grain size. Results showed that the Cu concentrations varied from 6.9–244 mg/kg with an average of 109±66 mg/kg. The spatial distribution of Cu reveals that the Cu concentration is relatively high in the river mouth region, and gradually diminishes toward the harbor entrance region. This indicates that upstream industrial and municipal wastewater discharges along the river bank are major sources of Cu pollution. Results from the enrichment factor and geo-accumulation index analyses imply that the sediments collected from the river mouth can be characterized between moderate and moderately severe degree enrichment and between none to medium and moderate accumulation of Cu, respectively. However, results of potential ecological risk index indicate that the sediment has low ecological potential risk.
Abstract: Superplastic deformation and high temperature load
relaxation behavior of coarse-grained iron aluminides with the
composition of Fe-28 at.% Al have been investigated. A series of load
relaxation and tensile tests were conducted at temperatures ranging
from 600 to 850oC. The flow curves obtained from load relaxation
tests were found to have a sigmoidal shape and to exhibit stress vs.
strain rate data in a very wide strain rate range from 10-7/s to 10-2/s.
Tensile tests have been conducted at various initial strain rates ranging
from 3×10-5/s to 1×10-2/s. Maximum elongation of ~500 % was
obtained at the initial strain rate of 3×10-5/s and the maximum strain
rate sensitivity was found to be 0.68 at 850oC in binary Fe-28Al alloy.
Microstructure observation through the optical microscopy (OM) and
the electron back-scattered diffraction (EBSD) technique has been
carried out on the deformed specimens and it has revealed the
evidences for grain boundary migration and grain refinement to occur
during superplastic deformation, suggesting the dynamic
recrystallization mechanism. The addition of Cr by the amount of 5
at.% appeared to deteriorate the superplasticity of the binary iron
aluminide. By applying the internal variable theory of structural
superplasticity, the addition of Cr has been revealed to lower the
contribution of the frictional resistance to dislocation glide during high
temperature deformation of the Fe3Al alloy.
Abstract: Abrasive Jet Machining is an Unconventional
machining process in which the metal is removed from brittle and
hard material in the form of micro-chips. With increase in need of
materials like ceramics, composites, in manufacturing of various
Mechanical & Electronic components, AJM has become a useful
technique for micro machining. The present study highlights the
influence of different parameters like Pressure, SOD, Time, Abrasive
grain size, nozzle diameter on the Metal removal of FRP (Fiber
Reinforced Polymer) composite by Abrasive jet machining. The
results of the Experiments conducted were analyzed and optimized
with TAGUCHI method of Optimization and ANOVA for Optimal
Value.
Abstract: This paper addresses modeling and optimization of process parameters in powder mixed electrical discharge machining (PMEDM). The process output characteristics include metal removal rate (MRR) and electrode wear rate (EWR). Grain size of Aluminum powder (S), concentration of the powder (C), discharge current (I) pulse on time (T) are chosen as control variables to study the process performance. The experimental results are used to develop the regression models based on second order polynomial equations for the different process characteristics. Then, a genetic algorithm (GA) has been employed to determine optimal process parameters for any desired output values of machining characteristics.
Abstract: Field mapping activity for an active volcano mainly in
the Torrid Zone is usually hampered by several problems such as steep
terrain and bad atmosphere conditions. In this paper we present a
simple solution for such problem by a combination Synthetic Aperture
Radar (SAR) and geostatistical methods. By this combination, we
could reduce the speckle effect from the SAR data and then estimate
roughness distribution of the pyroclastic flow deposits. The main
purpose of this study is to detect spatial distribution of new pyroclastic
flow deposits termed as P-zone accurately using the β°data from two
RADARSAT-1 SAR level-0 data. Single scene of Hyperion data and
field observation were used for cross-validation of the SAR results.
Mt. Merapi in central Java, Indonesia, was chosen as a study site and
the eruptions in May-June 2006 were examined. The P-zones were
found in the western and southern flanks. The area size and the longest
flow distance were calculated as 2.3 km2 and 6.8 km, respectively. The
grain size variation of the P-zone was mapped in detail from fine to
coarse deposits regarding the C-band wavelength of 5.6 cm.
Abstract: The distribution, enrichment, and accumulation of zinc
(Zn) in the sediments of Kaohsiung Ocean Disposal Site (KODS),
Taiwan were investigated. Sediment samples from two outer disposal
site stations and nine disposed stations in the KODS were collected per
quarterly in 2009 and characterized for Zn, aluminum, organic matter,
and grain size. Results showed that the mean Zn concentrations varied
from 48 mg/kg to 456 mg/kg. Results from the enrichment factor (EF)
and geo-accumulation index (Igeo) analyses imply that the sediments
collected from the KODS can be characterized between moderate and
moderately severe degree enrichment and between none and none to
medium accumulation of Zn, respectively. However, results of
potential ecological risk index indicate that the sediment has low
ecological potential risk. The EF, Igeo, and Zn concentrations at the
disposed stations were slightly higher than those at outer disposal site.
This indicated that the disposed area centers may be subjected to the
disposal impaction of harbor dredged sediments.
Abstract: The systematic manipulations of shapes and sizes of
inorganic compounds greatly benefit the various application fields
including optics, magnetic, electronics, catalysis and medicine.
However shape control has been much more difficult to achieve.
Hence exploration of novel method for the preparation of differently
shaped nanoparticles is challenging research area. II-VI group of
semiconductor cadmium sulphide (CdS) nanostructure with different
morphologies (such as, acicular like, mesoporous, spherical shapes)
and of crystallite sizes vary from 11 to 16 nm were successfully
synthesized by chemical aqueous precipitation of Cd2+ ions with
homogeneously released S2- ions from decomposition of cadmium
sulphate (CdSO4) and thioacetamide (CH3CSNH2) by annealing at
different radiations (microwave, ultrasonic and sunlight) with matter
and systematic research has been done for various factors affecting
the controlled growth rate of CdS nanoparticles. The obtained
nanomaterials have been characterized by X-ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FTIR),
Thermogravometric (DSC-TGA) analysis and Scanning Electron
Microscopy (SEM). The result indicates that on increasing the
reaction time particle size increases but on increasing the molar ratios
grain size decreases.