Abstract: Soil contamination phenomena are a wide world issue that has received the important attention in the last decades. The main pollutants that have affected soils are especially those resulted from the oil extraction, transport and processing. This paper presents results obtained in the framework of a research project focused on the management of contaminated sites with petroleum products/ REMPET. One of the specific objectives of the REMPET project was to assess the electrochemical treatment (improved with polarity change respect to the typical approach) as a treatment option for the remediation of total petroleum hydrocarbons (TPHs) from contaminated soils. Petroleum hydrocarbon compounds attach to soil components and are difficult to remove and degrade. Electrochemical treatment is a physicochemical treatment that has gained acceptance as an alternative method, for the remediation of organic contaminated soils comparing with the traditional methods as bioremediation and chemical oxidation. This type of treatment need short time and have high removal efficiency, being usually applied in heterogeneous soils with low permeability. During the experimental tests, the following parameters were monitored: pH, redox potential, humidity, current intensity, energy consumption. The electrochemical method was applied in an experimental setup with the next dimensions: 450 mm x 150 mm x 150 mm (L x l x h). The setup length was devised in three electrochemical cells that were connected at two power supplies. The power supplies configuration was provided in such manner that each cell has a cathode and an anode without overlapping. The initial value of TPH concentration in soil was of 1420.28 mg/kgdw. The remediation method has been applied for only 21 days, when it was already noticed an average removal efficiency of 31 %, with better results in the anode area respect to the cathode one (33% respect to 27%). The energy consumption registered after the development of the experiment was 10.6 kWh for exterior power supply and 16.1 kWh for the interior one. Taking into account that at national level, the most used methods for soil remediation are bioremediation (which needs too much time to be implemented and depends on many factors) and thermal desorption (which involves high costs in order to be implemented), the study of electrochemical treatment will give an alternative to these two methods (and their limitations).
Abstract: This paper discusses the importance of having a good initial characterization of soil samples when thermal desorption has to be applied to polluted soils for the removal of contaminants. Particular attention has to be devoted on the desorption kinetics of the samples to identify the gases evolved during the heating, and contaminant degradation pathways. In this study, two samples coming from different points of the same contaminated site were considered. The samples are much different from each other. Moreover, the presence of high initial quantity of heavy hydrocarbons strongly affected the performance of thermal desorption, resulting in formation of dangerous intermediates. Analytical techniques such TGA (Thermogravimetric Analysis), DSC (Differential Scanning Calorimetry) and GC-MS (Gas Chromatography-Mass) provided a good support to give correct indication for field application.
Abstract: This paper reveals the interaction between hydrogen
and surface stress in austenitic stainless steel by X-ray diffraction
stress measurement and thermal desorption analysis before and after
being charged with hydrogen. The surface residual stress was varied
by surface finishing using several disc polishing agents. The obtained
results show that the residual stress near surface had a significant
effect on hydrogen absorption behavior, that is, tensile residual stress
promoted the hydrogen absorption and compressive one did opposite.
Also, hydrogen induced equi-biaxial stress and this stress has a linear
correlation with hydrogen content.
Abstract: Smoke from domestic wood burning has been
identified as a major contributor to air pollution, motivating detailed
emission measurements under controlled conditions. A series of
experiments was performed to characterise the emissions from wood
combustion in a fireplace and in a woodstove of two common species
of trees grown in Spain: Pyrenean oak (Quercus pyrenaica) and
black poplar (Populus nigra). Volatile organic compounds (VOCs) in
the exhaust emissions were collected in Tedlar bags, re-sampled in
sorbent tubes and analysed by thermal desorption-gas
chromatography-flame ionisation detection. Pyrenean oak presented
substantially higher emissions in the woodstove than in the fireplace,
for the majority of compounds. The opposite was observed for
poplar. Among the 45 identified species, benzene and benzenerelated
compounds represent the most abundant group, followed by
oxygenated VOCs and aliphatics. Emission factors obtained in this
study are generally of the same order than those reported for
residential experiments in the USA.