Abstract: Rapid urbanization, industrialization and population
growth have led to an increase in number of automobiles that cause
air pollution. It is estimated that road traffic contributes 60% of air
pollution in urban areas. A case by case assessment is required to
predict the air quality in urban situations, so as to evolve certain
traffic management measures to maintain the air quality levels with
in the tolerable limits. Calicut city in the state of Kerala, India has
been chosen as the study area. Carbon Monoxide (CO) concentration
was monitored at 15 links in Calicut city and air quality performance
was evaluated over each link. The CO pollutant concentration values
were compared with the National Ambient Air Quality Standards
(NAAQS), and the CO values were predicted by using CALINE4 and
IITLS and Linear regression models. The study has revealed that
linear regression model performs better than the CALINE4 and
IITLS models. The possible association between CO pollutant
concentration and traffic parameters like traffic flow, type of vehicle,
and traffic stream speed was also evaluated.
Abstract: Camera calibration is an indispensable step for augmented
reality or image guided applications where quantitative information
should be derived from the images. Usually, a camera
calibration is obtained by taking images of a special calibration object
and extracting the image coordinates of projected calibration marks
enabling the calculation of the projection from the 3d world coordinates
to the 2d image coordinates. Thus such a procedure exhibits
typical steps, including feature point localization in the acquired
images, camera model fitting, correction of distortion introduced by
the optics and finally an optimization of the model-s parameters. In
this paper we propose to extend this list by further step concerning
the identification of the optimal subset of images yielding the smallest
overall calibration error. For this, we present a Monte Carlo based
algorithm along with a deterministic extension that automatically
determines the images yielding an optimal calibration. Finally, we
present results proving that the calibration can be significantly
improved by automated image selection.
Abstract: Fuzzy logic control (FLC) systems have been tested in
many technical and industrial applications as a useful modeling tool
that can handle the uncertainties and nonlinearities of modern control
systems. The main drawback of the FLC methodologies in the
industrial environment is challenging for selecting the number of
optimum tuning parameters.
In this paper, a method has been proposed for finding the optimum
membership functions of a fuzzy system using particle swarm
optimization (PSO) algorithm. A synthetic algorithm combined from
fuzzy logic control and PSO algorithm is used to design a controller
for a continuous stirred tank reactor (CSTR) with the aim of
achieving the accurate and acceptable desired results. To exhibit the
effectiveness of proposed algorithm, it is used to optimize the
Gaussian membership functions of the fuzzy model of a nonlinear
CSTR system as a case study. It is clearly proved that the optimized
membership functions (MFs) provided better performance than a
fuzzy model for the same system, when the MFs were heuristically
defined.
Abstract: The stochastic nature of tool life using conventional discrete-wear data from experimental tests usually exists due to many individual and interacting parameters. It is a common practice in batch production to continually use the same tool to machine different parts, using disparate machining parameters. In such an environment, the optimal points at which tools have to be changed, while achieving minimum production cost and maximum production rate within the surface roughness specifications, have not been adequately studied. In the current study, two relevant aspects are investigated using coated and uncoated inserts in turning operations: (i) the accuracy of using machinability information, from fixed parameters testing procedures, when variable parameters situations are emerged, and (ii) the credibility of tool life machinability data from prior discrete testing procedures in a non-stop machining. A novel technique is proposed and verified to normalize the conventional fixed parameters machinability data to suit the cases when parameters have to be changed for the same tool. Also, an experimental investigation has been established to evaluate the error in the tool life assessment when machinability from discrete testing procedures is employed in uninterrupted practical machining.
Abstract: Soil chemical and physical properties have important
roles in compartment of the environment and agricultural
sustainability and human health. The objectives of this research is
determination of spatial distribution patterns of Cd, Zn, K, pH, TNV,
organic material and electrical conductivity (EC) in agricultural soils
of Natanz region in Esfehan province. In this study geostatistic and
non-geostatistic methods were used for prediction of spatial
distribution of these parameters. 64 composite soils samples were
taken at 0-20 cm depth. The study area is located in south of
NATANZ agricultural lands with area of 21660 hectares. Spatial
distribution of Cd, Zn, K, pH, TNV, organic material and electrical
conductivity (EC) was determined using geostatistic and geographic
information system. Results showed that Cd, pH, TNV and K data
has normal distribution and Zn, OC and EC data had not normal
distribution. Kriging, Inverse Distance Weighting (IDW), Local
Polynomial Interpolation (LPI) and Redial Basis functions (RBF)
methods were used to interpolation. Trend analysis showed that
organic carbon in north-south and east to west did not have trend
while K and TNV had second degree trend. We used some error
measurements include, mean absolute error(MAE), mean squared
error (MSE) and mean biased error(MBE). Ordinary
kriging(exponential model), LPI(Local polynomial interpolation),
RBF(radial basis functions) and IDW methods have been chosen as
the best methods to interpolating of the soil parameters. Prediction
maps by disjunctive kriging was shown that in whole study area was
intensive shortage of organic matter and more than 63.4 percent of
study area had shortage of K amount.
Abstract: Mathematical models can be used to describe the
transmission of disease. Dengue disease is the most significant
mosquito-borne viral disease of human. It now a leading cause of
childhood deaths and hospitalizations in many countries. Variations
in environmental conditions, especially seasonal climatic parameters,
effect to the transmission of dengue viruses the dengue viruses and
their principal mosquito vector, Aedes aegypti. A transmission model
for dengue disease is discussed in this paper. We assume that the
human and vector populations are constant. We showed that the local
stability is completely determined by the threshold parameter, 0 B . If
0 B is less than one, the disease free equilibrium state is stable. If
0 B is more than one, a unique endemic equilibrium state exists and
is stable. The numerical results are shown for the different values of
the transmission probability from vector to human populations.
Abstract: In the present work flow past circular cylinder and
cylinder with rectangular and triangular wake splitter is studied to
improve aerodynamic parameters. The Comparison of drag
coefficient is tabulated for bare cylinder, cylinder with rectangular
and triangular wake splitters. Flow past circular cylinder and cylinder
with triangular and rectangular wake splitter is performed at
Reynoldsnumber 5, 20, 40, 50,80, 100.An incompressible PISO finite
volume code employing a non-staggered grid arrangement is used, a
second order upwind scheme is used for convective terms. The time
discretization is implicit and a Second order Crank-Nicholson scheme
is employed. Length of wake splitter in both configurations is taken
to be equal to diameter of cylinder. Wake length is found to be less
with rectangular wake splitter when compared to bare cylinder and
cylinder with triangular wake splitter. Coefficient of drag is found to
be less for triangular wake splitter when compared to bare cylinder &
cylinder with rectangular wake splitter.
Abstract: In this paper, we propose a single sample path based
algorithm with state aggregation to optimize the average rewards of
singularly perturbed Markov reward processes (SPMRPs) with a
large scale state spaces. It is assumed that such a reward process
depend on a set of parameters. Differing from the other kinds of
Markov chain, SPMRPs have their own hierarchical structure. Based
on this special structure, our algorithm can alleviate the load in the
optimization for performance. Moreover, our method can be applied
on line because of its evolution with the sample path simulated.
Compared with the original algorithm applied on these problems of
general MRPs, a new gradient formula for average reward
performance metric in SPMRPs is brought in, which will be proved
in Appendix, and then based on these gradients, the schedule of the
iteration algorithm is presented, which is based on a single sample
path, and eventually a special case in which parameters only
dominate the disturbance matrices will be analyzed, and a precise
comparison with be displayed between our algorithm with the old
ones which is aim to solve these problems in general Markov reward
processes. When applied in SPMRPs, our method will approach a fast
pace in these cases. Furthermore, to illustrate the practical value of
SPMRPs, a simple example in multiple programming in computer
systems will be listed and simulated. Corresponding to some practical
model, physical meanings of SPMRPs in networks of queues will be
clarified.
Abstract: In this study, a software has been developed to predict
the optimum conditions for drying of cotton based yarn bobbins in a
hot air dryer. For this purpose, firstly, a suitable drying model has
been specified using experimental drying behavior for different
values of drying parameters. Drying parameters in the experiments
were drying temperature, drying pressure, and volumetric flow rate of
drying air. After obtaining a suitable drying model, additional curve
fittings have been performed to obtain equations for drying time and
energy consumption taking into account the effects of drying
parameters. Then, a software has been developed using Visual Basic
programming language to predict the optimum drying conditions for
drying time and energy consumption.
Abstract: In this paper, the experimental design of using the
Taguchi method is employed to optimize the processing parameters in
the plasma arc surface hardening process. The processing parameters
evaluated are arc current, scanning velocity and carbon content of
steel. In addition, other significant effects such as the relation between
processing parameters are also investigated. An orthogonal array,
signal-to-noise (S/N) ratio and analysis of variance (ANOVA) are
employed to investigate the effects of these processing parameters.
Through this study, not only the hardened depth increased and surface
roughness improved, but also the parameters that significantly affect
the hardening performance are identified. Experimental results are
provided to verify the effectiveness of this approach.
Abstract: Musculoskeletal problems are common in high
performance dance population. This study attempts to identify lower
extremity muscle flexibility parameters prevailing among
bharatanatyam dancers and analyze if there is any significant
difference exist between normal and injured dancers in flexibility
parameters. Four hundred and one female dancers and 17 male
dancers were participated in this study. Flexibility parameters
(hamstring tightness, hip internal and external rotation and
tendoachilles in supine and sitting posture) were measured using
goniometer. Results of our study it is evident that injured female
bharathnatyam dancers had significantly (p < 0.05) high hamstring
tightness on left side lower extremity compared to normal female
dancers. The range of motion for left tendoachilles was significantly
(p < 0.05) high for the normal female group when compared to
injured dancers during supine lying posture. Majority of the injured
dancers had high hamstring tightness that could be a possible reason
for pain and MSDs.
Abstract: A decomposition of a graph G is a collection ψ of
graphs H1,H2, . . . , Hr of G such that every edge of G belongs
to exactly one Hi. If each Hi is either an induced path in G,
then ψ is called an induced acyclic path decomposition of G and
if each Hi is a (induced) cycle in G then ψ is called a (induced)
cycle decomposition of G. The minimum cardinality of an induced
acyclic path decomposition of G is called the induced acyclic path
decomposition number of G and is denoted by ¤Çia(G). Similarly
the cyclic decomposition number ¤Çc(G) is defined. In this paper we
begin an investigation of these parameters.