Abstract: In order to give high expertise the computer aided
design of mechanical systems involves specific activities focused on
processing two type of information: knowledge and data. Expert rule
based knowledge is generally processing qualitative information and
involves searching for proper solutions and their combination into
synthetic variant. Data processing is based on computational models
and it is supposed to be inter-related with reasoning in the knowledge
processing. In this paper an Intelligent Integrated System is proposed,
for the objective of choosing the adequate material. The software is
developed in Prolog – Flex software and takes into account various
constraints that appear in the accurate operation of gears.
Abstract: One of the best ways for achievement of conventional
vehicle changing to hybrid case is trustworthy simulation result and
using of driving realities. For this object, in this paper, at first sevendegree-
of-freedom dynamical model of vehicle will be shown. Then
by using of statically model of engine, gear box, clutch, differential,
electrical machine and battery, the hybrid automobile modeling will
be down and forward simulation of vehicle for pedals to wheels
power transformation will be obtained. Then by design of a fuzzy
controller and using the proper rule base, fuel economy and
regenerative braking will be marked. Finally a series of
MATLAB/SIMULINK simulation results will be proved the
effectiveness of proposed structure.
Abstract: Recent medical studies have investigated the importance of enteral feeding and the use of feeding pumps for recovering patients unable to feed themselves or gain nourishment and nutrients by natural means. The most of enteral feeding system uses a peristaltic tube pump. A peristaltic pump is a form of positive displacement pump in which a flexible tube is progressively squeezed externally to allow the resulting enclosed pillow of fluid to progress along it. The squeezing of the tube requires a precise and robust controller of the geared motor to overcome parametric uncertainty of the pumping system which generates due to a wide variation of friction and slip between tube and roller. So, this paper proposes fuzzy adaptive controller for the robust control of the peristaltic tube pump. This new adaptive controller uses a fuzzy multi-layered architecture which has several independent fuzzy controllers in parallel, each with different robust stability area. Out of several independent fuzzy controllers, the most suited one is selected by a system identifier which observes variations in the controlled system parameter. This paper proposes a design procedure which can be carried out mathematically and systematically from the model of a controlled system. Finally, the good control performance, accurate dose rate and robust system stability, of the developed feeding pump is confirmed through experimental and clinic testing.
Abstract: The accelerated growth in aircraft industries desire
effectual schemes, programs, innovative designs of advanced systems
to accomplishing the augmenting need for home-free air
transportation. In this paper, a contemporary conceptual design of an
airplane has been proposed without landing gear systems in order to
reducing accidents, time consumption, and to eliminating drawbacks
by using superconducting levitation phenomenon. This invention of
an airplane with superconductive material coating, on the solar plexus
region assist to reduce weight by approximately 4% of the total takeoff
weight, and cost effective. Moreover, we conjectured that
superconductor landing system reduces ground friction, mission fuel,
total drag, take-off and landing distance.
Abstract: In this paper, some common gearboxes vibration analysis methods and condition monitoring systems are explained. In addition, an experimental gearbox vibration analysis is discussed through a critical case history for a mixer gearbox related to Iran oil industry. The case history also consists of gear manufacturing (machining) recommendations, lubrication condition of gearbox and machinery maintenance activities that caused reduction in noise and vibration of the gearbox. Besides some of the recent patents and innovations in gearboxes, lubrication and vibration monitoring systems explained. Finally micro pitting and surface fatigue in pinion and bevel of mentioned horizontal to vertical gearbox discussed in details.
Abstract: The Institute of Product Development is dealing
with the development, design and dimensioning of micro components
and systems as a member of the Collaborative Research
Centre 499 “Design, Production and Quality Assurance of
Molded micro components made of Metallic and Ceramic Materials".
Because of technological restrictions in the miniaturization
of conventional manufacturing techniques, shape and
material deviations cannot be scaled down in the same proportion
as the micro parts, rendering components with relatively
wide tolerance fields. Systems that include such components
should be designed with this particularity in mind, often requiring
large clearance. On the end, the output of such systems
results variable and prone to dynamical instability. To save
production time and resources, every study of these effects
should happen early in the product development process and
base on computer simulation to avoid costly prototypes. A
suitable method is proposed here and exemplary applied to a
micro technology demonstrator developed by the CRC499. It
consists of a one stage planetary gear train in a sun-planet-ring
configuration, with input through the sun gear and output
through the carrier. The simulation procedure relies on ordinary
Multi Body Simulation methods and subsequently adds
other techniques to further investigate details of the system-s
behavior and to predict its response. The selection of the relevant
parameters and output functions followed the engineering
standards for regular sized gear trains. The first step is to
quantify the variability and to reveal the most critical points of
the system, performed through a whole-mechanism Sensitivity
Analysis. Due to the lack of previous knowledge about the system-s
behavior, different DOE methods involving small and
large amount of experiments were selected to perform the SA.
In this particular case the parameter space can be divided into
two well defined groups, one of them containing the gear-s profile
information and the other the components- spatial location.
This has been exploited to explore the different DOE techniques
more promptly. A reduced set of parameters is derived for
further investigation and to feed the final optimization process,
whether as optimization parameters or as external perturbation
collective. The 10 most relevant perturbation factors and 4 to 6
prospective variable parameters are considered in a new, simplified
model. All of the parameters are affected by the mentioned
production variability. The objective functions of interest
are based on scalar output-s variability measures, so the
problem becomes an optimization under robustness and reliability constrains. The study shows an initial step on the development
path of a method to design and optimize complex micro
mechanisms composed of wide tolerated elements accounting
for the robustness and reliability of the systems- output.
Abstract: In this paper, a study on the applications of the
optimization and regression techniques for optimal calculation of
partial ratios of helical gearboxes with second-step double gear-sets
for minimal cross section dimension is introduced. From the condition
of the moment equilibrium of a mechanic system including three gear
units and their regular resistance condition, models for calculation of
the partial ratios of helical gearboxes with second-step double
gear-sets were given. Especially, by regression analysis, explicit
models for calculation of the partial ratios are introduced. These
models allow determining the partial ratios accurately and simply.
Abstract: This paper presents a digital engineering library – the
Digital Mechanism and Gear Library, DMG-Lib – providing a multimedia collection of e-books, pictures, videos and animations in the domain of mechanisms and machines. The specific characteristic
about DMG-Lib is the enrichment and cross-linking of the different
sources. DMG-Lib e-books not only present pages as pixel images
but also selected figures augmented with interactive animations. The
presentation of animations in e-books increases the clearness of the
information.
To present the multimedia e-books and make them available in the
DMG-Lib internet portal a special e-book reader called StreamBook
was developed for optimal presentation of digitized books and to
enable reading the e-books as well as working efficiently and individually with the enriched information. The objective is to support different user tasks ranging from information retrieval to
development and design of mechanisms.
Abstract: Injection forging is a Nett-shape manufacturing
process in which one or two punches move axially causing a radial
flow into a die cavity in a form which is prescribed by the exitgeometry,
such as pulley, flanges, gears and splines on a shaft. This
paper presents an experimental and numerical study of the injection
forging of splines in terms of load requirement and material flow.
Three dimensional finite element analyses are used to investigate the
effect of some important parameters in this process. The experiment
has been carried out using solid commercial lead billets with two
different billet diameters and four different dies.
Abstract: In this paper, the wear of high speed steel hobs during
hobbing has been studied. The wear mechanisms are strongly
influenced by the choice of cutting speed. At moderate and high
cutting speeds three major wear mechanisms were identified:
abrasion, mild adhesive and severe adhesive. The microstructure and
wear behavior of two high speed steel grades (M2 and ASP30) has
been compared. In contrast, a variation in chemical composition or
microstructure of HSS tool material generally did not change the
dominant wear mechanism. However, the tool material properties
determine the resistance against the operating wear mechanism and
consequently the tool life. The metallographic analysis and wear
measurement at the tip of hob teeth included scanning electron
microscopy and stereoscope microscopy. Roughness profilometery is
used for measuring the gear surface roughness.
Abstract: In this paper an analytical crack propagation scenario
is proposed which assumes that a crack propagates in the tooth root in
both the crack depth direction and the tooth width direction, and
which is more reasonable and realistic for non-uniform load
distribution cases than the other presented scenarios. An analytical
approach is used for quantifying the loss of time-varying gear mesh
stiffness with the presence of crack propagation in the gear tooth root.
The proposed crack propagation scenario can be applied for crack
propagation modelling and monitoring simulation, but further
research is required for comparison and evaluation of all the
presented crack propagation scenarios from the condition monitoring
point of view.
Abstract: Antioxidant activities of ethanolic extracts of Ardisia
japonica Blume., Ageartum conyzoides Linn., and Cocculus hirsutus
Linn Diels. leaves was determined qualitatively and quantitatively in
this research. 1, 1-diphenyl-2-picrylhydrazyl (DPPH) free radical
solution was used to investigate free radical scavenging activity of
these leaves extracts. Ascorbic acid (Vitamin C) was used as the
standard. In the present investigation, it is found that all of these
extracts have remarkable antioxidant activities. The EC50 values of
these ethanolic extracts were 12.72 μg/ml for A. japonica, 15.19
μg/ml for A. conyzoides, 10.68 μg/ml for C. hirsutus respectively.
Among these Myanmar medicinal plants, C. hirsutus showed higher
antioxidant activities as well as free radical scavenging activity than
black tea (Camellia sinensis), the famous antioxidant, and A.
japonica and A. conyzoides showed a rather lower antioxidant
activity than tea extracts. According to results from bioassay with
carrot discs infected with Agrobacterium tumefaciens, all extracts
showed anti-tumor activity after 3 weeks of incubation. No gall was
detected in carrot disks treated with C. hirsutus and A. japonica
extracts in the dose of 100ppm and in carrot discs treated with A.
conyzoides extract in the dose of 1000 ppm. Therefore, the research
clearly indicates that these weedy plants of dry farm land are
exceptionally advantageous for human health.
Abstract: The proposed paper examines strategies whose aim is
to counter the all too often sighted process of abandonment that
characterizes contemporary cities. The city of Nicosia in Cyprus is
used as an indicative case study, whereby several recent projects are
presented as capitalizing on traditional cultural assets to revive the
downtown. The reuse of existing building stock as museums,
performing arts centers and theaters but also as in the form of various
housing typologies is geared to strengthen the ranks of local residents
and to spur economic growth. Unlike the examples from the 1960s,
the architecture of more recent adaptive reuse for urban regeneration
seems to be geared in reinforcing a connection to the city where the
buildings often reflect the characteristics of their urban context.
Abstract: This paper addresses issues of integral steering of
vehicles with two steering axles, where the rear wheels are pivoted in
the direction of the front wheels, but also in the opposite direction.
The steering box of the rear axle is presented with simple linkages
(single contour) that correlate the pivoting of the rear wheels
according to the direction of the front wheels, respectively to the
rotation angle of the steering wheel. The functionality of the system
is analyzed – the extent to which the requirements of the integral
steering are met by the considered/proposed mechanisms. The paper
highlights the quality of the single contour linkages, with two driving
elements for meeting these requirements, emphasizing diagrams of
mechanisms with 2 driving elements. Cam variants are analyzed and
proposed for the rear axle steering box. Cam profiles are determined
by various factors.
Abstract: This study presents a systematic analysis of the
dynamic behaviors of a gear-bearing system with porous squeeze film
damper (PSFD) under nonlinear suspension, nonlinear oil-film force
and nonlinear gear meshing force effect. It can be found that the
system exhibits very rich forms of sub-harmonic and even the chaotic
vibrations. The bifurcation diagrams also reveal that greater values of
permeability may not only improve non-periodic motions effectively,
but also suppress dynamic amplitudes of the system. Therefore, porous
effect plays an important role to improve dynamic stability of
gear-bearing systems or other mechanical systems. The results
presented in this study provide some useful insights into the design
and development of a gear-bearing system for rotating machinery that
operates in highly rotational speed and highly nonlinear regimes.
Abstract: Research on damage of gears and gear pairs using
vibration signals remains very attractive, because vibration signals
from a gear pair are complex in nature and not easy to interpret.
Predicting gear pair defects by analyzing changes in vibration signal
of gears pairs in operation is a very reliable method. Therefore, a
suitable vibration signal processing technique is necessary to extract
defect information generally obscured by the noise from dynamic
factors of other gear pairs.This article presents the value of cepstrum
analysis in vehicle gearbox fault diagnosis. Cepstrum represents the
overall power content of a whole family of harmonics and sidebands
when more than one family of sidebands is present at the same time.
The concept for the measurement and analysis involved in using the
technique are briefly outlined. Cepstrum analysis is used for detection
of an artificial pitting defect in a vehicle gearbox loaded with
different speeds and torques. The test stand is equipped with three
dynamometers; the input dynamometer serves asthe internal
combustion engine, the output dynamometers introduce the load on
the flanges of the output joint shafts. The pitting defect is
manufactured on the tooth side of a gear of the fifth speed on the
secondary shaft. Also, a method for fault diagnosis of gear faults is
presented based on order Cepstrum. The procedure is illustrated with
the experimental vibration data of the vehicle gearbox. The results
show the effectiveness of Cepstrum analysis in detection and
diagnosis of the gear condition.
Abstract: Optimizing equipment selection in heavy earthwork
operations is a critical key in the success of any construction project.
The objective of this research incentive was geared towards
developing a computer model to assist contractors and construction
managers in estimating the cost of heavy earthwork operations.
Economical operation analysis was conducted for an equipment fleet
taking into consideration the owning and operating costs involved in
earthwork operations. The model is being developed in a Microsoft
environment and is capable of being integrated with other estimating
and optimization models. In this study, Caterpillar® Performance
Handbook [5] was the main resource used to obtain specifications of
selected equipment. The implementation of the model shall give
optimum selection of equipment fleet not only based on cost
effectiveness but also in terms of versatility. To validate the model, a
case study of an actual dam construction project was selected to
quantify its degree of accuracy.
Abstract: This paper presents the study of hardness profile of spur gear heated by induction heating process in function of the machine parameters, such as the power (kW), the heating time (s) and the generator frequency (kHz). The global work is realized by 3D finite-element simulation applied to the process by coupling and resolving the electromagnetic field and the heat transfer problems, and it was performed in three distinguished steps. First, a Comsol 3D model was built using an adequate formulation and taking into account the material properties and the machine parameters. Second, the convergence study was conducted to optimize the mesh. Then, the surface temperatures and the case depths were deeply analyzed in function of the initial current density and the heating time in medium frequency (MF) and high frequency (HF) heating modes and the edge effect were studied. Finally, the simulations results are validated using experimental tests.
Abstract: Above Elbow Prosthesis is one of the most commonly
amputated or missing limbs. The research is done for modelling
techniques of upper limb prosthesis and design of high torque, light
weight and compact in size elbow actuator. The purposed actuator
consists of a DC motor, planetary gear set and a harmonic drive. The
calculations show that the actuator is good enough to be used in real
life powered prosthetic upper limb or rehabilitation exoskeleton.
Abstract: The world's population continues to grow at a quarter of a million people per day, increasing the consumption of energy. This has made the world to face the problem of energy crisis now days. In response to the energy crisis, the principles of renewable energy gained popularity. There are much advancement made in developing the wind and solar energy farms across the world. These energy farms are not enough to meet the energy requirement of world. This has attracted investors to procure new sources of energy to be substituted. Among these sources, extraction of energy from the waves is considered as best option. The world oceans contain enough energy to meet the requirement of world. Significant advancements in design and technology are being made to make waves as a continuous source of energy. One major hurdle in launching wave energy devices in a developing country like Pakistan is the initial cost. A simple, reliable and cost effective wave energy converter (WEC) is required to meet the nation-s energy need. This paper will present a novel design proposed by team SAS for harnessing wave energy. This paper has three major sections. The first section will give a brief and concise view of ocean wave creation, propagation and the energy carried by them. The second section will explain the designing of SAS-2. A gear chain mechanism is used for transferring the energy from the buoy to a rotary generator. The third section will explain the manufacturing of scaled down model for SAS-2 .Many modifications are made in the trouble shooting stage. The design of SAS-2 is simple and very less maintenance is required. SAS-2 is producing electricity at Clifton. The initial cost of SAS-2 is very low. This has proved SAS- 2 as one of the cost effective and reliable source of harnessing wave energy for developing countries.