Abstract: A finite element analysis (FEA) computer software HyperWorks is utilized in re-designing an automotive component to reduce its mass. Reduction of components mass contributes towards environmental sustainability by saving world-s valuable metal resources and by reducing carbon emission through improved overall vehicle fuel efficiency. A shape optimization analysis was performed on a rear spindle component. Pre-processing and solving procedures were performed using HyperMesh and RADIOSS respectively. Shape variables were defined using HyperMorph. Then optimization solver OptiStruct was utilized with fatigue life set as a design constraint. Since Stress-Number of Cycle (S-N) theory deals with uni-axial stress, the Signed von Misses stress on the component was used for looking up damage on S-N curve, and Gerber criterion for mean stress corrections. The optimization analysis resulted in mass reduction of 24% of the original mass. The study proved that the adopted approach has high potential use for environmental sustainability.
Abstract: A wireless Ad-hoc network consists of wireless nodes
communicating without the need for a centralized administration, in
which all nodes potentially contribute to the routing process.In this
paper, we report the simulation results of four different scenarios for
wireless ad hoc networks having thirty nodes. The performances of
proposed networks are evaluated in terms of number of hops per
route, delay and throughput with the help of OPNET simulator.
Channel speed 1 Mbps and simulation time 600 sim-seconds were
taken for all scenarios. For the above analysis DSR routing protocols
has been used. The throughput obtained from the above analysis
(four scenario) are compared as shown in Figure 3. The average
media access delay at node_20 for two routes and at node_20 for four
different scenario are compared as shown in Figures 4 and 5. It is
observed that the throughput will degrade when it will follow
different hops for same source to destination (i.e. it has dropped from
1.55 Mbps to 1.43 Mbps which is around 9.7%, and then dropped to
0.48Mbps which is around 35%).
Abstract: In this study, a software has been developed to predict
the optimum conditions for drying of cotton based yarn bobbins in a
hot air dryer. For this purpose, firstly, a suitable drying model has
been specified using experimental drying behavior for different
values of drying parameters. Drying parameters in the experiments
were drying temperature, drying pressure, and volumetric flow rate of
drying air. After obtaining a suitable drying model, additional curve
fittings have been performed to obtain equations for drying time and
energy consumption taking into account the effects of drying
parameters. Then, a software has been developed using Visual Basic
programming language to predict the optimum drying conditions for
drying time and energy consumption.
Abstract: Glaucoma diagnosis involves extracting three features
of the fundus image; optic cup, optic disc and vernacular. Present
manual diagnosis is expensive, tedious and time consuming. A
number of researches have been conducted to automate this process.
However, the variability between the diagnostic capability of an
automated system and ophthalmologist has yet to be established. This
paper discusses the efficiency and variability between
ophthalmologist opinion and digital technique; threshold. The
efficiency and variability measures are based on image quality
grading; poor, satisfactory or good. The images are separated into
four channels; gray, red, green and blue. A scientific investigation
was conducted on three ophthalmologists who graded the images
based on the image quality. The images are threshold using multithresholding
and graded as done by the ophthalmologist. A
comparison of grade from the ophthalmologist and threshold is made.
The results show there is a small variability between result of
ophthalmologists and digital threshold.
Abstract: In the paper, the results of sensitivity analysis of the influence of initial imperfections on the web stress state of a thinwalled girder are presented. The results of the study corroborate a very good and effective agreement of experiments with theory. Most input random quantities were found experimentally. The change of sensitivity coefficients in dependence on working load value is analysed. The stress was analysed by means of a geometrically and materially non-linear solution by applying the program ANSYS. This research study offers important background for theoretical studies of stability problems, post-critical effects and limit states of thin-walled steel structures.
Abstract: Despite the fact that B2c eCommerce has become
important in numerous economies, its adoption varies from country to
country. This paper aims to identify the factors affecting (enabling or
inhibiting) B2c eCommerce and to determine their quantitative
impact on the diffusion of online sales across countries. A dynamic
panel model analyzing the relationship between 13 factors
(Macroeconomic, Demographic, Socio-Cultural, Infrastructural and
Offer related) stemming from a complete literature analysis and the
B2c eCommerce value in 45 countries over 9 years has been
developed. Having a positive correlation coefficient, GDP, mobile
penetration, Internet user penetration and credit card penetration
resulted as enabling drivers of the B2c eCommerce value across
countries, whereas, having a negative correlation coefficient,equal
distribution of income and the development of traditional retailing
network act as inhibiting factors.
Abstract: This paper proposes a feed-forward control in a halfbridge
resonant dc link inverter. The configuration of feed-forward
control is based on synchronous sigma-delta modulation and the halfbridge
resonant dc link inverter consists of two inductors, one
capacitor and two power switches. The simulation results show the
proposed technique can reject non-ideal dc bus improving the total
harmonic distortion.
Abstract: The conceptually construction of axially chiral indolostilbenesi.eN-(2-{(E)-2-[2'-(1-Acetyl-1H-indol-2-yl)-3'chloro-4,4',6,6'-tetramethoxy[1,1'-biphenyl]-2yl]ethenyl}phenyl)acetamide and N-(2-{(E)-2-[2'-(1-Acetyl-1H-indol-2-yl)-3'-chloro-2,4',6,6'-tetramethoxy[1,1'-biphenyl]-4-yl]ethenyl}phenyl) acetamide are described in this paper. These structure, were obtained by the tactical combination of palladium-catalyzed coupling which produced 10-acetamido-3,5-dimethoxystilbene, follow by FeCl3-induced oxidative cyclization/dimerisation. All structures were unambiguously confirmed by 1D (1H, 13C) and 2D NMR experiment, (COSY, HMQC, HMBC) and mass spectrometry.
Abstract: In this paper, we study the stability of a fractional order delayed predator-prey model. By using the Laplace transform, we introduce a characteristic equation for the above system. It is shown that if all roots of the characteristic equation have negative parts, then the equilibrium of the above fractional order predator-prey system is Lyapunov globally asymptotical stable. An example is given to show the effectiveness of the approach presented in this paper.
Abstract: The development of competences and practical
capacities of students is getting an important incidence into the
guidelines of the European Higher Education Area (EHEA). The
methodology applied in this work is based on the education through
directed resolution of practical cases. All cases are related to
professional tasks that the students will have to develop in their
future career. The method is intended to form the necessary
competences of students of the Marine Engineering and Maritime
Transport Degree in the matter of “Physics".
The experience was applied in the course of 2011/2012. Students
were grouped, and a practical task was assigned to them, that should
be developed and solved within the team. The aim was to realize
students learning by three ways: their own knowledge, the
contribution of their teammates and the teacher's direction. The
results of the evaluation were compared with those obtained
previously by the traditional teaching method.
Abstract: Although lots of experiments have been done in enhanced oil recovery, the number of experiments which consider the effects of local and global heterogeneity on efficiency of enhanced oil recovery based on the polymer-surfactant flooding is low and rarely done. In this research, we have done numerous experiments of water flooding and polymer-surfactant flooding on a five spot glass micromodel in different conditions such as different positions of layers. In these experiments, five different micromodels with three different pore structures are designed. Three models with different layer orientation, one homogenous model and one heterogeneous model are designed. In order to import the effect of heterogeneity of porous media, three types of pore structures are distributed accidentally and with equal ratio throughout heterogeneous micromodel network according to random normal distribution. The results show that maximum EOR recovery factor will happen in a situation where the layers are orthogonal to the path of mainstream and the minimum EOR recovery factor will happen in a situation where the model is heterogeneous. This experiments show that in polymer-surfactant flooding, with increase of angles of layers the EOR recovery factor will increase and this recovery factor is strongly affected by local heterogeneity around the injection zone.
Abstract: In this paper we present an efficient system for
independent speaker speech recognition based on neural network
approach. The proposed architecture comprises two phases: a
preprocessing phase which consists in segmental normalization and
features extraction and a classification phase which uses neural
networks based on nonparametric density estimation namely the
general regression neural network (GRNN). The relative
performances of the proposed model are compared to the similar
recognition systems based on the Multilayer Perceptron (MLP), the
Recurrent Neural Network (RNN) and the well known Discrete
Hidden Markov Model (HMM-VQ) that we have achieved also.
Experimental results obtained with Arabic digits have shown that the
use of nonparametric density estimation with an appropriate
smoothing factor (spread) improves the generalization power of the
neural network. The word error rate (WER) is reduced significantly
over the baseline HMM method. GRNN computation is a successful
alternative to the other neural network and DHMM.
Abstract: The effect of antifungal compound from Bacillus
subtilis strain LB5 was tested against conidial germination of
Colletotrichum gloeosporioides and Pestalotiopsis eugeniae, causal
agent of anthracnose and fruit rot of wax apple, respectively.
Observation under scanning electron microscope and light compound
microscope revealed that conidial germination was completely
inhibited when treated with culture broth, culture filtrate, or crude
extract from strain LB5. Identification of purified antifungal
compound produced by strain LB5 in cell-free supernatant by nuclear
magnetic resonance and fast atom bombardment showed that the
active compound was iturin A-2.
Abstract: In this paper an attempt has been made to correlate the usefulness of electrodes made through powder metallurgy (PM) in comparison with conventional copper electrode during electric discharge machining. Experimental results are presented on electric discharge machining of AISI D2 steel in kerosene with copper tungsten (30% Cu and 70% W) tool electrode made through powder metallurgy (PM) technique and Cu electrode. An L18 (21 37) orthogonal array of Taguchi methodology was used to identify the effect of process input factors (viz. current, duty cycle and flushing pressure) on the output factors {viz. material removal rate (MRR) and surface roughness (SR)}. It was found that CuW electrode (made through PM) gives high surface finish where as the Cu electrode is better for higher material removal rate.
Abstract: In this study we tried to replicate the unconscious
thought advantage (UTA), which states that complex decisions are
better handled by unconscious thinking. We designed an experiment
in e-prime using similar material as the original study (choosing
between four different apartments, each described by 12 attributes).
A total of 73 participants (52 women (71.2%); 18 to 62 age:
M=24.63; SD=8.7) took part in the experiment. We did not replicate
the results suggested by UTT. However, from the present study we
cannot conclude whether this was the case of flaws in the theory or
flaws in our experiment and we discuss several ways in which the
issue of UTA could be examined further.
Abstract: In the last few years, three multivariate spectral
analysis techniques namely, Principal Component Analysis (PCA),
Independent Component Analysis (ICA) and Non-negative Matrix
Factorization (NMF) have emerged as effective tools for oscillation
detection and isolation. While the first method is used in determining
the number of oscillatory sources, the latter two methods
are used to identify source signatures by formulating the detection
problem as a source identification problem in the spectral domain.
In this paper, we present a critical drawback of the underlying linear
(mixing) model which strongly limits the ability of the associated
source separation methods to determine the number of sources
and/or identify the physical source signatures. It is shown that the
assumed mixing model is only valid if each unit of the process gives
equal weighting (all-pass filter) to all oscillatory components in its
inputs. This is in contrast to the fact that each unit, in general, acts
as a filter with non-uniform frequency response. Thus, the model
can only facilitate correct identification of a source with a single
frequency component, which is again unrealistic. To overcome
this deficiency, an iterative post-processing algorithm that correctly
identifies the physical source(s) is developed. An additional issue
with the existing methods is that they lack a procedure to pre-screen
non-oscillatory/noisy measurements which obscure the identification
of oscillatory sources. In this regard, a pre-screening procedure
is prescribed based on the notion of sparseness index to eliminate
the noisy and non-oscillatory measurements from the data set used
for analysis.
Abstract: Knowing the geometrical object pose of products in manufacturing line before robot manipulation is required and less time consuming for overall shape measurement. In order to perform it, the information of shape representation and matching of objects is become required. Objects are compared with its descriptor that conceptually subtracted from each other to form scalar metric. When the metric value is smaller, the object is considered closed to each other. Rotating the object from static pose in some direction introduce the change of value in scalar metric value of boundary information after feature extraction of related object. In this paper, a proposal method for indexing technique for retrieval of 3D geometrical models based on similarity between boundaries shapes in order to measure 3D CAD object pose using object shape feature matching for Computer Aided Testing (CAT) system in production line is proposed. In experimental results shows the effectiveness of proposed method.
Abstract: Knowledge of patterns of genetic diversity enhances
the efficiency of germplasm conservation and improvement. In this
study 96 Iranian landraces of Triticum turgidum originating from
different geographical areas of Iran, along with 18 durum cultivars
from ten countries were evaluated for variation in morphological and
high molecular weight glutenin subunit (HMW-GS) composition.
The first two principal components clearly separated the Iranian
landraces from cultivars. Three alleles were present at the Glu-A1
locus and 11 alleles at Glu-B1. In both cultivars and landraces of
durum wheat, the null allele (Glu-A1c) was observed more
frequently than the Glu-A1a and Glu-A1b alleles. Two alleles,
namely Glu-B1a (subunit 7) and Glu-B1e (subunit 20) represented
the more frequent alleles at Glu-B1 locus. The results showed that
the evaluated Iranian landraces formed an interesting source of
favourable glutenin subunits that might be very desirable in breeding
activities for improving pasta-making quality.
Abstract: In this paper, the experimental design of using the
Taguchi method is employed to optimize the processing parameters in
the plasma arc surface hardening process. The processing parameters
evaluated are arc current, scanning velocity and carbon content of
steel. In addition, other significant effects such as the relation between
processing parameters are also investigated. An orthogonal array,
signal-to-noise (S/N) ratio and analysis of variance (ANOVA) are
employed to investigate the effects of these processing parameters.
Through this study, not only the hardened depth increased and surface
roughness improved, but also the parameters that significantly affect
the hardening performance are identified. Experimental results are
provided to verify the effectiveness of this approach.
Abstract: The most Malaria cases are occur along Thai-Mynmar border. Mathematical model for the transmission of Plasmodium falciparum and Plasmodium vivax malaria in a mixed population of Thais and migrant Burmese living along the Thai-Myanmar Border is studied. The population is separated into two groups, Thai and Burmese. Each population is divided into susceptible, infected, dormant and recovered subclasses. The loss of immunity by individuals in the infected class causes them to move back into the susceptible class. The person who is infected with Plasmodium vivax and is a member of the dormant class can relapse back into the infected class. A standard dynamical method is used to analyze the behaviors of the model. Two stable equilibrium states, a disease-free state and an epidemic state, are found to be possible in each population. A disease-free equilibrium state in the Thai population occurs when there are no infected Burmese entering the community. When infected Burmese enter the Thai community, an epidemic state can occur. It is found that the disease-free state is stable when the threshold number is less than one. The epidemic state is stable when a second threshold number is greater than one. Numerical simulations are used to confirm the results of our model.