Abstract: This study deals with Computational Fluid Dynamics
(CFD) studies of the interactions between the air flow and louvered
fins which equipped the automotive heat exchangers. 3D numerical
simulation results are obtained by using the ANSYS Fluent 13.0 code
and compared to experimental data. The paper studies the effect of
louver angle and louver pitch geometrical parameters, on overall
thermal hydraulic performances of louvered fins.
The comparison between CFD simulations and experimental data
show that established 3-D CFD model gives a good agreement. The
validation agrees, with about 7% of deviation respectively of friction
and Colburn factors to experimental results. As first, it is found that
the louver angle has a strong influence on the heat transfer rate. Then,
louver angle and louver pitch variation of the louvers and their effects
on thermal hydraulic performances are studied. In addition to this
study, it is shown that the second half of the fin takes has a
significant contribution on pressure drop increase without any
increase in heat transfer.
Abstract: CFD simulations are carried out in arterial stenoses
with 48 % areal occlusion. Non-newtonian fluid model is selected for
the blood flow as the same problem has been solved before with
Newtonian fluid model. Studies on flow resistance with the presence
of surface irregularities are carried out. Investigations are also
performed on the pressure drop at various Reynolds numbers. The
present study revealed that the pressure drop across a stenosed artery
is practically unaffected by surface irregularities at low Reynolds
numbers, while flow features are observed and discussed at higher
Reynolds numbers.
Abstract: The objective of this study is to investigate fire
behaviors, experimentally and numerically, in a scaled version of an
underground station. The effect of ventilation velocity on the fire is
examined. Fire experiments are simulated by burning 10 ml
isopropyl alcohol fuel in a fire pool with dimensions 5cm x 10cm x 4
mm at the center of 1/100 scaled underground station model. A
commercial CFD program FLUENT was used in numerical
simulations. For air flow simulations, k-ω SST turbulence model and
for combustion simulation, non-premixed combustion model are
used. This study showed that, the ventilation velocity is increased
from 1 m/s to 3 m/s the maximum temperature in the station is found
to be less for ventilation velocity of 1 m/s. The reason for these
experimental result lies on the relative dominance of oxygen supply
effect on cooling effect. Without piston effect, maximum temperature
occurs above the fuel pool. However, when the ventilation velocity
increased the flame was tilted in the direction of ventilation and the
location of maximum temperature moves along the flow direction.
The velocities measured experimentally in the station at different
locations are well matched by the CFD simulation results. The
prediction of general flow pattern is satisfactory with the smoke
visualization tests. The backlayering in velocity is well predicted by
CFD simulation. However, all over the station, the CFD simulations
predicted higher temperatures compared to experimental
measurements.
Abstract: Feeder is one of the airships of the Multibody Advanced Airship for Transport (MAAT) system, under development within the EU FP7 project. MAAT is based on a modular concept composed of two different parts that have the possibility to join; respectively they are the so-called Cruiser and Feeder, designed on the lighter than air principle. Feeder, also named ATEN (Airship Transport Elevator Network), is the smaller one which joins the bigger one, Cruiser, also named PTAH (Photovoltaic modular Transport Airship for High altitude),envisaged to happen at 15km altitude. During the MAAT design phase, the aerodynamic studies of the both airships and their interactions are analyzed. The objective of these studies is to understand the aerodynamic behavior of all the preselected configurations, as an important element in the overall MAAT system design. The most of these configurations are only simulated by CFD, while the most feasible one is experimentally analyzed in order to validate and thrust the CFD predictions. This paper presents the numerical and experimental investigation of the Feeder “conical like" shape configuration. The experiments are focused on the aerodynamic force coefficients and the pressure distribution over the Feeder outer surface, while the numerical simulation cover also the analysis of the velocity and pressure distribution. Finally, the wind tunnel experiment is compared with its CFD model in order to validate such specific simulations with respective experiments and to better understand the difference between the wind tunnel and in-flight circumstances.
Abstract: Natural ventilation has played an important role for
many low energy-building designs. It has been also noticed as a
essential subject to persistently bring the fresh cool air from the
outside into a building. This study carried out the computational fluid
dynamics (CFD)-based simulations to examine the natural ventilation
development of a work area in a public building. The simulated results
can be useful to better understand the indoor microclimate and the
interaction of wind with buildings. Besides, this CFD simulation
procedure can serve as an effective analysis tool to characterize the
airing performance, and thereby optimize the building ventilation for
strengthening the architects, planners and other decision makers on
improving the natural ventilation design of public buildings.