Abstract: Wind turbines with double output induction
generators can operate at variable speed permitting conversion
efficiency maximization over a wide range of wind velocities. This
paper presents the performance analysis of a wind driven double
output induction generator (DOIG) operating at varying shafts speed.
A periodic transient state analysis of DOIG equipped with two
converters is carried out using a hybrid induction machine model.
This paper simulates the harmonic content of waveforms in various
points of drive at different speeds, based on the hybrid model
(dqabc). Then the sinusoidal and trapezoidal pulse-width–modulation
control techniques are used in order to improve the power factor of
the machine and to weaken the injected low order harmonics to the
supply. Based on the frequency spectrum, total harmonics distortion,
distortion factor and power factor. Finally advantages of sinusoidal
and trapezoidal pulse width modulation techniques are compared.
Abstract: Semiconductor materials with coatings have a wide range of applications in MEMS and NEMS. This work uses transfermatrix method for calculating the radiative properties. Dopped silicon is used and the coherent formulation is applied. The Drude model for the optical constants of doped silicon is employed. Results showed that for the visible wavelengths, more emittance occurs in greater concentrations and the reflectance decreases as the concentration increases. In these wavelengths, transmittance is negligible. Donars and acceptors act similar in visible wavelengths. The effect of wave interference can be understood by plotting the spectral properties such as reflectance or transmittance of a thin dielectric film versus the film thickness and analyzing the oscillations of properties due to constructive and destructive interferences. But this effect has not been shown at visible wavelengths. At room temperature, the scattering process is dominated by lattice scattering for lightly doped silicon, and the impurity scattering becomes important for heavily doped silicon when the dopant concentration exceeds1018cm-3 .
Abstract: Environmental aspects plays a central role in environmental management system (EMS) because it is the basis for the identification of an organization-s environmental targets. The
existing methods for the assessment of environmental aspects are grouped into three categories: risk assessment-based (RA-based),
LCA-based and criterion-based methods. To combine the benefits of
these three categories of research, this study proposes an integrated framework, combining RA-, LCA- and criterion-based methods. The
integrated framework incorporates LCA techniques for the identification of the causal linkage for aspect, pathway, receptor and
impact, uses fuzzy logic to assess aspects, considers fuzzy conditions,
in likelihood assessment, and employs a new multi-criteria decision analysis method - multi-criteria and multi-connection comprehensive
assessment (MMCA) - to estimate significant aspects in EMS. The proposed model is verified, using a real case study and the results show
that this method successfully prioritizes the environmental aspects.
Abstract: This study aims to clarify constructions which enable to improve socio-cultural values of environments and also to obtain new knowledge on selecting development plans. CVM is adopted as a method of evaluation. As a case of the research, university campus (CP; the following) is selected on account of its various environments, institutions and many users. Investigations were conducted from 4 points of view, total value and utility value of whole CP environments, values of each environment existing in CP or development plan assumed in CP. Furthermore, respondents- attributes were also investigated. In consequence, the following is obtained. 1) Almost all of total value of CP is composed of utility value of direct use. 2) Each of environment and development plans whose value is the highest is clarified. 3) Moreover, development plan to improve environmental value the most is specified.
Abstract: Weather systems use enormously complex
combinations of numerical tools for study and forecasting.
Unfortunately, due to phenomena in the world climate, such
as the greenhouse effect, classical models may become
insufficient mostly because they lack adaptation. Therefore,
the weather forecast problem is matched for heuristic
approaches, such as Evolutionary Algorithms.
Experimentation with heuristic methods like Particle Swarm
Optimization (PSO) algorithm can lead to the development of
new insights or promising models that can be fine tuned with
more focused techniques. This paper describes a PSO
approach for analysis and prediction of data and provides
experimental results of the aforementioned method on realworld
meteorological time series.
Abstract: A multivariable discontinuous feedback linearization approach is proposed to position control of an electrically driven fast robot manipulator. A desired performance is achieved by selecting a useful controller and suitable sampling rate and considering saturation for actuators. There is a high flexibility to apply the proposed control approach on different electrically driven manipulators. The control approach can guarantee the stability and satisfactory tracking performance. A PUMA 560 robot driven by geared permanent magnet dc motors is simulated. The simulation results show a desired performance for control system under technical specifications.
Abstract: The increasing competitiveness in manufacturing
industry is forcing manufacturers to seek effective processing
schedules. The paper presents an optimization manufacture
scheduling approach for dependent details processing with given
processing sequences and times on multiple machines. By defining
decision variables as start and end moments of details processing it is
possible to use straightforward variables restrictions to satisfy
different technological requirements and to formulate easy to
understand and solve optimization tasks for multiple numbers of
details and machines. A case study example is solved for seven base
moldings for CNC metalworking machines processed on five
different machines with given processing order among details and
machines and known processing time-s duration. As a result of linear
optimization task solution the optimal manufacturing schedule
minimizing the overall processing time is obtained. The
manufacturing schedule defines the moments of moldings delivery
thus minimizing storage costs and provides mounting due-time
satisfaction. The proposed optimization approach is based on real
manufacturing plant problem. Different processing schedules variants
for different technological restrictions were defined and implemented
in the practice of Bulgarian company RAIS Ltd. The proposed
approach could be generalized for other job shop scheduling
problems for different applications.
Abstract: Whereas in the third generation nuclear reactors,
dimensions of core and also the kind of coolant and enrichment
percent of fuel have significantly changed than the second
generation, therefore in this article the aim is based on a
comparative investigation between two same power reactors of
second and third generations, that the neutronic parameters of both
reactors such as: K∞, Keff and its details and thermal hydraulic
parameters such as: power density, specific power, volumetric heat
rate, released power per fuel volume unit, volume and mass of clad
and fuel (consisting fissile and fertile fuels), be calculated and
compared together. By this comparing the efficiency and
modification of third generation nuclear reactors than second
generation which have same power can be distinguished.
In order to calculate the cited parameters, some information
such as: core dimensions, the pitch of lattice, the fuel matter, the
percent of enrichment and the kind of coolant are used. For
calculating the neutronic parameters, a neutronic program entitled:
SIXFAC and also related formulas have been used. Meantime for
calculating the thermal hydraulic and other parameters, analytical
method and related formulas have been applied.
Abstract: In this paper, we consider a food-limited population model with delay and feedback control. By applying the comparison theorem of the differential equation and constructing a suitable Lyapunov functional, sufficient conditions which guarantee the permanence and existence of a unique globally attractive positive almost periodic solution of the system are obtained.
Abstract: In recent years, many researches to mine the exploding Web world, especially User Generated Content (UGC) such as
weblogs, for knowledge about various phenomena and events in the physical world have been done actively, and also Web services
with the Web-mined knowledge have begun to be developed for
the public. However, there are few detailed investigations on how accurately Web-mined data reflect physical-world data. It must be
problematic to idolatrously utilize the Web-mined data in public Web services without ensuring their accuracy sufficiently. Therefore,
this paper introduces the simplest Web Sensor and spatiotemporallynormalized
Web Sensor to extract spatiotemporal data about a target
phenomenon from weblogs searched by keyword(s) representing the
target phenomenon, and tries to validate the potential and reliability of the Web-sensed spatiotemporal data by four kinds of granularity
analyses of coefficient correlation with temperature, rainfall, snowfall,
and earthquake statistics per day by region of Japan Meteorological
Agency as physical-world data: spatial granularity (region-s population
density), temporal granularity (time period, e.g., per day vs. per week), representation granularity (e.g., “rain" vs. “heavy rain"), and
media granularity (weblogs vs. microblogs such as Tweets).
Abstract: Most electrical distribution systems are incurring large
losses as the loads are wide spread, inadequate reactive power
compensation facilities and their improper control. A typical static
VAR compensator consists of capacitor bank in binary sequential
steps operated in conjunction with a thyristor controlled reactor of the
smallest step size. This SVC facilitates stepless control of reactive
power closely matching with load requirements so as to maintain
power factor nearer to unity. This type of SVC-s requiring a
appropriately controlled TCR. This paper deals with an air cored
reactor suitable for distribution transformer of 3phase, 50Hz, Dy11,
11KV/433V, 125 KVA capacity. Air cored reactors are designed,
built, tested and operated in conjunction with capacitor bank in five
binary sequential steps. It is established how the delta connected TCR
minimizes the harmonic components and the operating range for
various electrical quantities as a function of firing angle is
investigated. In particular firing angle v/s line & phase currents, D.C.
components, THD-s, active and reactive powers, odd and even triplen
harmonics, dominant characteristic harmonics are all investigated and
range of firing angle is fixed for satisfactory operation. The harmonic
spectra for phase and line quantities at specified firing angles are
given. In case the TCR is operated within the bound specified in this
paper established through simulation studies are yielding the best
possible operating condition particularly free from all dominant
harmonics.
Abstract: In real-time networks a large number of application programs are relying on video data and heterogeneous data transmission techniques. The aim of this research is presenting a method for end-to-end vouch quality service in surface applicationlayer for sending video data in comparison form in wireless heterogeneous networks. This method tries to improve the video sending over the wireless heterogeneous networks with used techniques in surface layer, link and application. The offered method is showing a considerable improvement in quality observing by user. In addition to this, other specifications such as shortage of data load that had require to resending and limited the relation period length to require time for second data sending, help to be used the offered method in the wireless devices that have a limited energy. The presented method and the achieved improvement is simulated and presented in the NS-2 software.
Abstract: This paper reviews designs of the built environment
from a sustainability perspective, emphasizing their importance in
achieving ecological and sustainable economic objectives. The built
environment has traditionally resulted in loss of biodiversity,
extinction of some species, climate change, excessive water use, land
degradation, space depletion, waste accumulation, energy
consumption and environmental pollution. Materials used like
plastics, metals, bricks, concrete, cement, natural aggregates, glass
and plaster have wreaked havoc on the earth´s resources, since they
have high levels of embodied energy hence not sustainable.
Additional resources are consumed during use and disposal phases.
Proposed designs for sustainability solutions include: ecological
sanitation and eco-efficiency systems that ensure social, economic,
environmental and technical sustainability. Renewable materials and
energy systems, passive cooling and heating systems and material
and energy reduction, reuse and recycling can improve the sector.
These ideas are intended to inform the field of ecological design of
the built environment.
Abstract: As global industry developed rapidly, the energy
demand also rises simultaneously. In the production process, there’s a
lot of energy consumed in the process. Formally, the energy used in
generating the heat in the production process. In the total energy
consumption, 40% of the heat was used in process heat, mechanical
work, chemical energy and electricity. The remaining 50% were
released into the environment. It will cause energy waste and
environment pollution. There are many ways for recovering the waste
heat in factory. Organic Rankine Cycle (ORC) system can produce
electricity and reduce energy costs by recovering the waste of low
temperature heat in the factory. In addition, ORC is the technology
with the highest power generating efficiency in low-temperature heat
recycling. However, most of factories executives are still hesitated
because of the high implementation cost of the ORC system, even a lot
of heat are wasted. Therefore, this study constructs a nonlinear
mathematical model of waste heat recovery equipment configuration
to maximize profits. A particle swarm optimization algorithm is
developed to generate the optimal facility installation plan for the ORC
system.
Abstract: Accident in spent fuel pool (SFP) of Fukushima
Daiichi Unit 4 showed the importance of continuous monitoring of the
key environmental parameters such as water temperature, water level,
and radiation level in the SFP at accident conditions. Because the SFP
water temperature is one of the key parameters indicating SFP
conditions, its behavior at accident conditions shall be understood to
prepare appropriate measures. This study estimated temporal change
in the SFP water temperature at Kori Unit 1 with 587 MWe for 1 hour
after initiation of a loss-of-pool-cooling accident. For the estimation,
ANSYS CFX 13.0 code was used. The estimation showed that the
increasing rate of the water temperature was 3.90C per hour and the
SFP water temperature could reach 1000C in 25.6 hours after the
initiation of loss-of-pool-cooling accident.
Abstract: In this work, we analyze the deformation of surface
waves in shallow flows conditions, propagating in a channel of
slowly varying cross-section. Based on a singular perturbation
technique, the main purpose is to predict the motion of waves by
using a dimensionless formulation of the governing equations,
considering that the longitudinal variation of the transversal section
obey a power-law distribution. We show that the spatial distribution
of the waves in the varying cross-section is a function of a kinematic
parameter,κ , and two geometrical parameters εh
and w ε . The above
spatial behavior of the surface elevation is modeled by an ordinary
differential equation. The use of single formulas to model the varying
cross sections or transitions considered in this work can be a useful
approximation to natural or artificial geometrical configurations.
Abstract: Deoxygenation of beef fat for the production of hydrogenated biodiesel is investigated in a high pressure continuous flow fixed bed reactor over palladium-supported mesoporous titania catalyst synthesized via a combined single-step sol-gel process with surfactant-assisted templating method (SATM). The catalyst possessed a mesoporous charactheristic with high surface area and narrow pore size distribution. The main products of all Pd/TiO2 catalysts are n-heptadecane (n-C17) and n-pentadecane (n-C15) resulting from decarbonylation reaction. Pd/TiO2 catalyst synthesized via a combined single-step sol-gel process with SATM (SSSG) gave higher activity and selectivity to the desired products when compared to IWI/SG-TiO2 and IWI/P25-TiO2, respectively. SSSG catalyst gave the average conversion up to 80-90 % and 80 % for the selectivity in diesel range hydrocarbons. This result may cause by the higher surface area and the ability in dispersion of palladium ion in mesoporous of TiO2 during sol-gel process.
Abstract: Cryptographic protocols are widely used in various
applications to provide secure communications. They are usually
represented as communicating agents that send and receive messages.
These agents use their knowledge to exchange information and
communicate with other agents involved in the protocol. An agent
knowledge can be partitioned into explicit knowledge and procedural
knowledge. The explicit knowledge refers to the set of information
which is either proper to the agent or directly obtained from other
agents through communication. The procedural knowledge relates to
the set of mechanisms used to get new information from what is
already available to the agent.
In this paper, we propose a mathematical framework which specifies
the explicit knowledge of an agent involved in a cryptographic
protocol. Modelling this knowledge is crucial for the specification,
analysis, and implementation of cryptographic protocols. We also,
report on a prototype tool that allows the representation and the
manipulation of the explicit knowledge.
Abstract: The shortest path (SP) problem concerns with finding the shortest path from a specific origin to a specified destination in a given network while minimizing the total cost associated with the path. This problem has widespread applications. Important applications of the SP problem include vehicle routing in transportation systems particularly in the field of in-vehicle Route Guidance System (RGS) and traffic assignment problem (in transportation planning). Well known applications of evolutionary methods like Genetic Algorithms (GA), Ant Colony Optimization, Particle Swarm Optimization (PSO) have come up to solve complex optimization problems to overcome the shortcomings of existing shortest path analysis methods. It has been reported by various researchers that PSO performs better than other evolutionary optimization algorithms in terms of success rate and solution quality. Further Geographic Information Systems (GIS) have emerged as key information systems for geospatial data analysis and visualization. This research paper is focused towards the application of PSO for solving the shortest path problem between multiple points of interest (POI) based on spatial data of Allahabad City and traffic speed data collected using GPS. Geovisualization of results of analysis is carried out in GIS.
Abstract: Testing accounts for the major percentage of technical
contribution in the software development process. Typically, it
consumes more than 50 percent of the total cost of developing a
piece of software. The selection of software tests is a very important
activity within this process to ensure the software reliability
requirements are met. Generally tests are run to achieve maximum
coverage of the software code and very little attention is given to the
achieved reliability of the software. Using an existing methodology,
this paper describes how to use Bayesian Belief Networks (BBNs) to
select unit tests based on their contribution to the reliability of the
module under consideration. In particular the work examines how the
approach can enhance test-first development by assessing the quality
of test suites resulting from this development methodology and
providing insight into additional tests that can significantly reduce
the achieved reliability. In this way the method can produce an
optimal selection of inputs and the order in which the tests are
executed to maximize the software reliability. To illustrate this
approach, a belief network is constructed for a modern software
system incorporating the expert opinion, expressed through
probabilities of the relative quality of the elements of the software,
and the potential effectiveness of the software tests. The steps
involved in constructing the Bayesian Network are explained as is a
method to allow for the test suite resulting from test-driven
development.