Abstract: This paper evaluate the multilevel modulation for
different techniques such as amplitude shift keying (M-ASK), MASK,
differential phase shift keying (M-ASK-Bipolar), Quaternary
Amplitude Shift Keying (QASK) and Quaternary Polarization-ASK
(QPol-ASK) at a total bit rate of 107 Gbps. The aim is to find a costeffective
very high speed transport solution. Numerical investigation
was performed using Monte Carlo simulations. The obtained results
indicate that some modulation formats can be operated at 100Gbps
in optical communication systems with low implementation effort
and high spectral efficiency.
Abstract: Many accidents were happened because of fast driving, habitual working overtime or tired spirit. This paper presents a solution of remote warning for vehicles collision avoidance using vehicular communication. The development system integrates dedicated short range communication (DSRC) and global position system (GPS) with embedded system into a powerful remote warning system. To transmit the vehicular information and broadcast vehicle position; DSRC communication technology is adopt as the bridge. The proposed system is divided into two parts of the positioning andvehicular units in a vehicle. The positioning unit is used to provide the position and heading information from GPS module, and furthermore the vehicular unit is used to receive the break, throttle, and othersignals via controller area network (CAN) interface connected to each mechanism. The mobile hardware are built with an embedded system using X86 processor in Linux system. A vehicle is communicated with other vehicles via DSRC in non-addressed protocol with wireless access in vehicular environments (WAVE) short message protocol. From the position data and vehicular information, this paper provided a conflict detection algorithm to do time separation and remote warning with error bubble consideration. And the warning information is on-line displayed in the screen. This system is able to enhance driver assistance service and realize critical safety by using vehicular information from the neighbor vehicles.KeywordsDedicated short range communication, GPS, Control area network, Collision avoidance warning system.
Abstract: Hemodialysis patients might suffer from unhealthy
care behaviors or long-term dialysis treatments. Ultimately they need
to be hospitalized. If the hospitalization rate of a hemodialysis center
is high, its quality of service would be low. Therefore, how to decrease
hospitalization rate is a crucial problem for health care. In this study
we combined temporal abstraction with data mining techniques for
analyzing the dialysis patients' biochemical data to develop a decision
support system. The mined temporal patterns are helpful for clinicians
to predict hospitalization of hemodialysis patients and to suggest them
some treatments immediately to avoid hospitalization.
Abstract: In this study, production possibilities of hydrogen and/or methane via SCWG from black grape residues have been investigated. For this aim, grape residues which remain as a byproduct of the wine making process have been used. Since utilization from grape residues is limited due to the high moisture content, supercritical water gasification is the most convenient method. The effect of the gasification temperature and type of catalyst on supercritical water gasification have been investigated. Gasification experiments were performed in a batch autoclave at four different temperatures 300, 400, 500 and 600°C. K2CO3 and Trona (NaHCO3.Na2CO3·2H2O) were used as catalyst. Real biomass types of black grape residues have been successfully gasified and the product gas (hydrogen, methane, carbon dioxide, carbon monoxide and a small amount of ethane and ethylene) were identified by using gas chromatography. A TOC analyzer was used to determine total organic carbon (TOC) content of aqueous phase. The amounts of carboxylic acids, aldehydes, ketones, furfurals and phenols present in the aqueous solutions were analyzed by high performance liquid chromatography. When the temperature increased from 300°C to 600°C, mol% of H2 in gas products increased. The presence of catalysts improves the hydrogen yield. Trona showed gasification activity to be similar to that of K2CO3. It may be concluded that the use of Trona instead of commercially produced catalysts, can be preferably used in the gasification of biomass in supercritical water.
Abstract: This paper presents design features of a rescue robot, named CEO Mission II. Its body is designed to be the track wheel type with double front flippers for climbing over the collapse and the rough terrain. With 125 cm. long, 5-joint mechanical arm installed on the robot body, it is deployed not only for surveillance from the top view but also easier and faster access to the victims to get their vital signs. Two cameras and sensors for searching vital signs are set up at the tip of the multi-joint mechanical arm. The third camera is at the back of the robot for driving control. Hardware and software of the system, which controls and monitors the rescue robot, are explained. The control system is used for controlling the robot locomotion, the 5-joint mechanical arm, and for turning on/off devices. The monitoring system gathers all information from 7 distance sensors, IR temperature sensors, 3 CCD cameras, voice sensor, robot wheels encoders, yawn/pitch/roll angle sensors, laser range finder and 8 spare A/D inputs. All sensors and controlling data are communicated with a remote control station via IEEE 802.11b Wi-Fi. The audio and video data are compressed and sent via another IEEE 802.11g Wi-Fi transmitter for getting real-time response. At remote control station site, the robot locomotion and the mechanical arm are controlled by joystick. Moreover, the user-friendly GUI control program is developed based on the clicking and dragging method to easily control the movement of the arm. Robot traveling map is plotted from computing the information of wheel encoders and the yawn/pitch data. 2D Obstacle map is plotted from data of the laser range finder. The concept and design of this robot can be adapted to suit many other applications. As the Best Technique awardee from Thailand Rescue Robot Championship 2006, all testing results are satisfied.
Abstract: Burnishing is a method of finishing and hardening
machined parts by plastic deformation of the surface. Experimental
work based on central composite second order rotatable design has
been carried out on a lathe machine to establish the effects of ball
burnishing parameters on the surface roughness of brass material.
Analysis of the results by the analysis of variance technique and the
F-test show that the parameters considered, have significant effects
on the surface roughness.
Abstract: In spite of all advancement in software testing,
debugging remains a labor-intensive, manual, time consuming, and
error prone process. A candidate solution to enhance debugging
process is to fuse it with testing process. To achieve this integration,
a possible solution may be categorizing common software tests and
errors followed by the effort on fixing the errors through general
solutions for each test/error pair. Our approach to address this issue is
based on Christopher Alexander-s pattern and pattern language
concepts. The patterns in this language are grouped into three major
sections and connect the three concepts of test, error, and debug.
These patterns and their hierarchical relationship shape a pattern
language that introduces a solution to solve software errors in a
known testing context.
Finally, we will introduce our developed framework ADE as a
sample implementation to support a pattern of proposed language,
which aims to automate the whole process of evolving software
design via evolutionary methods.
Abstract: This paper proposes a novel system for monitoring the
health of underground pipelines. Some of these pipelines transport
dangerous contents and any damage incurred might have catastrophic
consequences. However, most of these damage are unintentional and
usually a result of surrounding construction activities. In order to
prevent these potential damages, monitoring systems are
indispensable. This paper focuses on acoustically recognizing road
cutters since they prelude most construction activities in modern
cities. Acoustic recognition can be easily achieved by installing a
distributed computing sensor network along the pipelines and using
smart sensors to “listen" for potential threat; if there is a real threat,
raise some form of alarm. For efficient pipeline monitoring, a novel
monitoring approach is proposed. Principal Component Analysis
(PCA) was studied and applied. Eigenvalues were regarded as the
special signature that could characterize a sound sample, and were
thus used for the feature vector for sound recognition. The denoising
ability of PCA could make it robust to noise interference. One class
SVM was used for classifier. On-site experiment results show that the
proposed PCA and SVM based acoustic recognition system will be
very effective with a low tendency for raising false alarms.
Abstract: Previously, harmonic parameters (HPs) have been
selected as features extracted from EEG signals for automatic sleep
scoring. However, in previous studies, only one HP parameter was
used, which were directly extracted from the whole epoch of EEG
signal.
In this study, two different transformations were applied to extract
HPs from EEG signals: Hilbert-Huang transform (HHT) and wavelet
transform (WT). EEG signals are decomposed by the two
transformations; and features were extracted from different
components. Twelve parameters (four sets of HPs) were extracted.
Some of the parameters are highly diverse among different stages.
Afterward, HPs from two transformations were used to building a
rough sleep stages scoring model using the classifier SVM. The
performance of this model is about 78% using the features obtained by
our proposed extractions. Our results suggest that these features may
be useful for automatic sleep stages scoring.
Abstract: In this paper, the robust exponential stability problem of discrete-time uncertain stochastic neural networks with timevarying delays is investigated. By introducing a new augmented Lyapunov function, some delay-dependent stable results are obtained in terms of linear matrix inequality (LMI) technique. Compared with some existing results in the literature, the conservatism of the new criteria is reduced notably. Three numerical examples are provided to demonstrate the less conservatism and effectiveness of the proposed method.
Abstract: Three-dimensional simulation of harmonic up
generation in free electron laser amplifier operating simultaneously
with a cold and relativistic electron beam is presented in steady-state
regime where the slippage of the electromagnetic wave with respect
to the electron beam is ignored. By using slowly varying envelope
approximation and applying the source-dependent expansion to wave
equations, electromagnetic fields are represented in terms of the
Hermit Gaussian modes which are well suited for the planar wiggler
configuration. The electron dynamics is described by the fully threedimensional
Lorentz force equation in presence of the realistic planar
magnetostatic wiggler and electromagnetic fields. A set of coupled
nonlinear first-order differential equations is derived and solved
numerically. The fundamental and third harmonic radiation of the
beam is considered. In addition to uniform beam, prebunched
electron beam has also been studied. For this effect of sinusoidal
distribution of entry times for the electron beam on the evolution of
radiation is compared with uniform distribution. It is shown that
prebunching reduces the saturation length substantially. For
efficiency enhancement the wiggler is set to decrease linearly when
the radiation of the third harmonic saturates. The optimum starting
point of tapering and the slope of radiation in the amplitude of
wiggler are found by successive run of the code.
Abstract: This paper presented a new approach for centralized
monitoring and self-protected against fiber fault in fiber-to-the-home
(FTTH) access network by using Smart Access Network Testing,
Analyzing and Database (SANTAD). SANTAD will be installed
with optical line terminal (OLT) at central office (CO) for in-service
transmission surveillance and fiber fault localization within FTTH
with point-to-multipoint (P2MP) configuration downwardly from CO
towards customer residential locations based on the graphical user
interface (GUI) processing capabilities of MATLAB software.
SANTAD is able to detect any fiber fault as well as identify the
failure location in the network system. SANTAD enable the status of
each optical network unit (ONU) connected line is displayed onto
one screen with capability to configure the attenuation and detect the
failure simultaneously. The analysis results and information will be
delivered to the field engineer for promptly actions, meanwhile the
failure line will be diverted to protection line to ensure the traffic
flow continuously. This approach has a bright prospect to improve
the survivability and reliability as well as increase the efficiency and
monitoring capabilities in FTTH.
Abstract: A mathematical model for the hydrodynamic
lubrication of parabolic slider bearings with couple stress lubricants
is presented. A numerical solution for the mathematical model using
finite element scheme is obtained using three nodes isoparametric
quadratic elements. Stiffness integrals obtained from the weak form
of the governing equations were solved using Gauss Quadrature to
obtain a finite number of stiffness matrices. The global system of
equations was obtained for the bearing and solved using Gauss Seidel
iterative scheme. The converged pressure solution was used to obtain
the load capacity of the bearing. Parametric studies were carried out
and it was shown that the effect of couple stresses and profile
parameter are to increase the load carrying capacity of the parabolic
slider bearing. Numerical experiments reveal that the magnitude of
the profile parameter at which maximum load is obtained increases
with decrease in couple stress parameter. The results are presented in
graphical form.
Abstract: Noise has adverse effect on human health and
comfort. Noise not only cause hearing impairment, but it also acts as
a causal factor for stress and raising systolic pressure. Additionally it
can be a causal factor in work accidents, both by marking hazards
and warning signals and by impeding concentration. Industry
workers also suffer psychological and physical stress as well as
hearing loss due to industrial noise. This paper proposes an approach
to enable engineers to point out quantitatively the noisiest source for
modification, while multiple machines are operating simultaneously.
The model with the point source and spherical radiation in a free field
was adopted to formulate the problem. The procedure works very
well in ideal cases (point source and free field). However, most of the
industrial noise problems are complicated by the fact that the noise is
confined in a room. Reflections from the walls, floor, ceiling, and
equipment in a room create a reverberant sound field that alters the
sound wave characteristics from those for the free field. So the model
was validated for relatively low absorption room at NIT Kurukshetra
Central Workshop. The results of validation pointed out that the
estimated sound power of noise sources under simultaneous
conditions were on lower side, within the error limits 3.56 - 6.35 %.
Thus suggesting the use of this methodology for practical
implementation in industry. To demonstrate the application of the
above analytical procedure for estimating the sound power of noise
sources under simultaneous operating conditions, a manufacturing
facility (Railway Workshop at Yamunanagar, India) having five
sound sources (machines) on its workshop floor is considered in this
study. The findings of the case study had identified the two most
effective candidates (noise sources) for noise control in the Railway
Workshop Yamunanagar, India. The study suggests that the
modification in the design and/or replacement of these two identified
noisiest sources (machine) would be necessary so as to achieve an
effective reduction in noise levels. Further, the estimated data allows
engineers to better understand the noise situations of the workplace
and to revise the map when changes occur in noise level due to a
workplace re-layout.
Abstract: Flight management system (FMS) is a specialized
computer system that automates a wide variety of in-flight tasks,
reducing the workload on the flight crew to the point that modern
aircraft no longer carry flight engineers or navigators. The primary
function of FMS is to perform the in-flight management of the flight
plan using various sensors (such as GPS and INS often backed up by
radio navigation) to determine the aircraft's position. From the
cockpit FMS is normally controlled through a Control Display Unit
(CDU) which incorporates a small screen and keyboard or touch
screen. This paper investigates the performance of GPS/ INS
integration techniques in which the data fusion process is done using
Kalman filtering. This will include the importance of sensors
calibration as well as the alignment of the strap down inertial
navigation system. The limitations of the inertial navigation systems
are investigated in order to understand why INS sometimes is
integrated with other navigation aids and not just operating in standalone
mode. Finally, both the loosely coupled and tightly coupled
configurations are analyzed for several types of situations and
operational conditions.
Abstract: This paper discusses a design of nonlinear observer by
a formal linearization method using an application of Chebyshev Interpolation
in order to facilitate processes for synthesizing a nonlinear
observer and to improve the precision of linearization.
A dynamic nonlinear system is linearized with respect to a linearization
function, and a measurement equation is transformed into
an augmented linear one by the formal linearization method which is
based on Chebyshev interpolation. To the linearized system, a linear
estimation theory is applied and a nonlinear observer is derived. To
show effectiveness of the observer design, numerical experiments
are illustrated and they indicate that the design shows remarkable
performances for nonlinear systems.
Abstract: The increasing industrialization and motorization of the world has led to a steep rise for the demand of petroleum-based fuels. Petroleum-based fuels are obtained from limited reserves. These finite reserves are highly concentrated in certain regions of the world. Therefore, those countries not having these resources are facing energy/foreign exchange crisis, mainly due to the import of crude petroleum. Hence, it is necessary to look for alternative fuels which can be produced from resources available locally within the country such as alcohol, biodiesel, vegetable oils etc. Biodiesel is a renewable, domestically produced fuel that has been shown to reduce particulate, hydrocarbon, and carbon monoxide emissions from combustion. In the present study an experimental investigation on emission characteristic of a liquid burner system operating on several percentage of biodiesel and gas oil is carried out. Samples of exhaust gas are analysed with Testo 350 Xl. The results show that biodiesel can lower some pollutant such as CO, CO2 and particulate matter emissions while NOx emission would increase in comparison with gas oil. The results indicate there may be benefits to using biodiesel in industrial processes.
Abstract: An artificial neural network (ANN) model is
presented for the prediction of kinematic viscosity of binary mixtures
of poly (ethylene glycol) (PEG) in water as a function of temperature,
number-average molecular weight and mass fraction. Kinematic
viscosities data of aqueous solutions for PEG (0.55419×10-6 –
9.875×10-6 m2/s) were obtained from the literature for a wide range
of temperatures (277.15 - 338.15 K), number-average molecular
weight (200 -10000), and mass fraction (0.0 – 1.0). A three layer
feed-forward artificial neural network was employed. This model
predicts the kinematic viscosity with a mean square error (MSE) of
0.281 and the coefficient of determination (R2) of 0.983. The results
show that the kinematic viscosity of binary mixture of PEG in water
could be successfully predicted using an artificial neural network
model.
Abstract: The data is available in abundance in any business
organization. It includes the records for finance, maintenance,
inventory, progress reports etc. As the time progresses, the data keep
on accumulating and the challenge is to extract the information from
this data bank. Knowledge discovery from these large and complex
databases is the key problem of this era. Data mining and machine
learning techniques are needed which can scale to the size of the
problems and can be customized to the application of business. For
the development of accurate and required information for particular
problem, business analyst needs to develop multidimensional models
which give the reliable information so that they can take right
decision for particular problem. If the multidimensional model does
not possess the advance features, the accuracy cannot be expected.
The present work involves the development of a Multidimensional
data model incorporating advance features. The criterion of
computation is based on the data precision and to include slowly
change time dimension. The final results are displayed in graphical
form.
Abstract: Activity-Based Costing (ABC) represents an
alternative paradigm to traditional cost accounting system and
it often provides more accurate cost information for decision
making such as product pricing, product mix, and make-orbuy
decisions. ABC models the causal relationships between
products and the resources used in their production and traces
the cost of products according to the activities through the use
of appropriate cost drivers. In this paper, the implementation
of the ABC in a manufacturing system is analyzed and a
comparison with the traditional cost based system in terms of
the effects on the product costs are carried out to highlight the
difference between two costing methodologies. By using this
methodology, a valuable insight into the factors that cause the
cost is provided, helping to better manage the activities of the
company.