Abstract: Freeze concentration freezes or crystallises the water
molecules out as ice crystals and leaves behind a highly concentrated
solution. In conventional suspension freeze concentration where ice
crystals formed as a suspension in the mother liquor, separation of
ice is difficult. The size of the ice crystals is still very limited which
will require usage of scraped surface heat exchangers, which is very
expensive and accounted for approximately 30% of the capital cost.
This research is conducted using a newer method of freeze
concentration, which is progressive freeze concentration. Ice crystals
were formed as a layer on the designed heat exchanger surface. In
this particular research, a helical structured copper crystallisation
chamber was designed and fabricated. The effect of two operating
conditions on the performance of the newly designed crystallisation
chamber was investigated, which are circulation flowrate and coolant
temperature. The performance of the design was evaluated by the
effective partition constant, K, calculated from the volume and
concentration of the solid and liquid phase. The system was also
monitored by a data acquisition tool in order to see the temperature
profile throughout the process. On completing the experimental
work, it was found that higher flowrate resulted in a lower K, which
translated into high efficiency. The efficiency is the highest at 1000
ml/min. It was also found that the process gives the highest
efficiency at a coolant temperature of -6 °C.
Abstract: Because of high ductility, aluminum alloys, have been widely used as an important base of metal forming industries. But the main week point of these alloys is their low strength so in forming them with conventional methods like deep drawing, hydro forming, etc have been always faced with problems like fracture during of forming process. Because of this, recently using of explosive forming method for forming of these plates has been recommended. In this paper free explosive forming of A2024 aluminum alloy is numerically simulated and during it, explosion wave propagation process is studied. Consequences of this simulation can be effective in prediction of quality of production. These consequences are compared with an experimental test and show the superiority of this method to similar methods like hydro forming and deep drawing.
Abstract: Software development has experienced remarkable progress in the past decade. However, due to the rising complexity and magnitude of the project the development productivity has not been consistently improved. By analyzing the latest ISBSG data repository with 4106 projects, we discovered that software development productivity has actually undergone irregular variations between the years 1995 and 2005. Considering the factors significant to the productivity, we found its variations are primarily caused by the variations of average team size and the unbalanced uses of the less productive language 3GL.
Abstract: In this paper, we use Radial Basis Function Networks
(RBFN) for solving the problem of environmental interference
cancellation of speech signal. We show that the Second Order Thin-
Plate Spline (SOTPS) kernel cancels the interferences effectively.
For make comparison, we test our experiments on two conventional
most used RBFN kernels: the Gaussian and First order TPS (FOTPS)
basis functions. The speech signals used here were taken from the
OGI Multi-Language Telephone Speech Corpus database and were
corrupted with six type of environmental noise from NOISEX-92
database. Experimental results show that the SOTPS kernel can
considerably outperform the Gaussian and FOTPS functions on
speech interference cancellation problem.
Abstract: Pattern matching is one of the fundamental applications in molecular biology. Searching DNA related data is a common activity for molecular biologists. In this paper we explore the applicability of a new pattern matching technique called Index based Forward Backward Multiple Pattern Matching algorithm(IFBMPM), for DNA Sequences. Our approach avoids unnecessary comparisons in the DNA Sequence due to this; the number of comparisons of the proposed algorithm is very less compared to other existing popular methods. The number of comparisons rapidly decreases and execution time decreases accordingly and shows better performance.
Abstract: In recent years multi-agent systems have emerged as one of the interesting architectures facilitating distributed collaboration and distributed problem solving. Each node (agent) of the network might pursue its own agenda, exploit its environment, develop its own problem solving strategy and establish required communication strategies. Within each node of the network, one could encounter a diversity of problem-solving approaches. Quite commonly the agents can realize their processing at the level of information granules that is the most suitable from their local points of view. Information granules can come at various levels of granularity. Each agent could exploit a certain formalism of information granulation engaging a machinery of fuzzy sets, interval analysis, rough sets, just to name a few dominant technologies of granular computing. Having this in mind, arises a fundamental issue of forming effective interaction linkages between the agents so that they fully broadcast their findings and benefit from interacting with others.
Abstract: People detection from images has a variety of applications such as video surveillance and driver assistance system, but is still a challenging task and more difficult in crowded environments such as shopping malls in which occlusion of lower parts of human body often occurs. Lack of the full-body information requires more effective features than common features such as HOG. In this paper, new features are introduced that exploits global self-symmetry (GSS) characteristic in head-shoulder patterns. The features encode the similarity or difference of color histograms and oriented gradient histograms between two vertically symmetric blocks. The domain-specific features are rapid to compute from the integral images in Viola-Jones cascade-of-rejecters framework. The proposed features are evaluated with our own head-shoulder dataset that, in part, consists of a well-known INRIA pedestrian dataset. Experimental results show that the GSS features are effective in reduction of false alarmsmarginally and the gradient GSS features are preferred more often than the color GSS ones in the feature selection.
Abstract: The switching lag-time and the voltage drop across
the power devices cause serious waveform distortions and
fundamental voltage drop in pulse width-modulated inverter output.
These phenomenons are conspicuous when both the output frequency
and voltage are low. To estimate the output voltage from the PWM
reference signal it is essential to take account of these imperfections
and to correct them. In this paper, on-line compensation method is
presented. It needs three simple blocs to add at the ideal reference
voltages. This method does not require any additional hardware
circuit and off- line experimental measurement. The paper includes
experimental results to demonstrate the validity of the proposed
method. It is applied, finally, in case of indirect vector controlled
induction machine and implemented using dSpace card.
Abstract: Missing data yields many analysis challenges. In case of complex survey design, in addition to dealing with missing data, researchers need to account for the sampling design to achieve useful inferences. Methods for incorporating sampling weights in neural network imputation were investigated to account for complex survey designs. An estimate of variance to account for the imputation uncertainty as well as the sampling design using neural networks will be provided. A simulation study was conducted to compare estimation results based on complete case analysis, multiple imputation using a Markov Chain Monte Carlo, and neural network imputation. Furthermore, a public-use dataset was used as an example to illustrate neural networks imputation under a complex survey design
Abstract: Using one dimensional Quantum hydrodynamic
(QHD) model Korteweg de Vries (KdV) solitary excitations of
electron-acoustic waves (EAWs) have been examined in twoelectron-
populated relativistically degenerate super dense plasma. It
is found that relativistic degeneracy parameter influences the
conditions of formation and properties of solitary structures.
Abstract: This study was initiated with a three prong objective.
One, to identify the relationship between Technological
Competencies factors (Technical Capability, Firm Innovativeness
and E-Business Practices and professional service firms- business
performance. To investigate the predictors of professional service
firms business performance and finally to evaluate the predictors of
business performance according to the type of professional service
firms, a survey questionnaire was deployed to collect empirical data.
The questionnaire was distributed to the owners of the professional
small medium size enterprises services in the Accounting, Legal,
Engineering and Architecture sectors. Analysis showed that all three
Technology Competency factors have moderate effect on business
performance. In addition, the regression models indicate that
technical capability is the most highly influential that could
determine business performance, followed by e-business practices
and firm innovativeness. Subsequently, the main predictor of
business performance for all types of firms is Technical capability.
Abstract: Group contribution methods such as the UNIFAC are
very useful to researchers and engineers involved in synthesis,
feasibility studies, design and optimization of separation processes.
They can be applied successfully to predict phase equilibrium and
excess properties in the development of chemical and separation
processes. The main focus of this work was to investigate the
possibility of absorbing selected volatile organic compounds (VOCs)
into polydimethylsiloxane (PDMS) using three selected UNIFAC
group contribution methods. Absorption followed by subsequent
stripping is the predominant available abatement technology of
VOCs from flue gases prior to their release into the atmosphere. The
original, modified and effective UNIFAC models were used in this
work. The thirteen selected VOCs that have been considered in this
research are: pentane, hexane, heptanes, trimethylamine, toluene,
xylene, cyclohexane, butyl acetate, diethyl acetate, chloroform,
acetone, ethyl methyl ketone and isobutyl methyl ketone. The
computation was done for solute VOC concentration of 8.55x10-8
which is well in the infinite dilution region. The results obtained in
this study compare very well with those published in literature
obtained through both measurements and predictions. The phase
equilibrium obtained in this study show that PDMS is a good
absorbent for the removal of VOCs from contaminated air streams
through physical absorption.
Abstract: This paper deals with a high-order accurate Runge
Kutta Discontinuous Galerkin (RKDG) method for the numerical
solution of the wave equation, which is one of the simple case of a
linear hyperbolic partial differential equation. Nodal DG method is
used for a finite element space discretization in 'x' by discontinuous
approximations. This method combines mainly two key ideas which
are based on the finite volume and finite element methods. The
physics of wave propagation being accounted for by means of
Riemann problems and accuracy is obtained by means of high-order
polynomial approximations within the elements. High order accurate
Low Storage Explicit Runge Kutta (LSERK) method is used for
temporal discretization in 't' that allows the method to be nonlinearly
stable regardless of its accuracy. The resulting RKDG
methods are stable and high-order accurate. The L1 ,L2 and L∞ error
norm analysis shows that the scheme is highly accurate and effective.
Hence, the method is well suited to achieve high order accurate
solution for the scalar wave equation and other hyperbolic equations.
Abstract: Human heart valves diseased by congenital heart
defects, rheumatic fever, bacterial infection, cancer may cause stenosis
or insufficiency in the valves. Treatment may be with medication but
often involves valve repair or replacement (insertion of an artificial
heart valve). Bileaflet mechanical heart valves (BMHVs) are widely
implanted to replace the diseased heart valves, but still suffer from
complications such as hemolysis, platelet activation, tissue
overgrowth and device failure. These complications are closely related
to both flow characteristics through the valves and leaflet dynamics. In
this study, the physiological flow interacting with the moving leaflets
in a bileaflet mechanical heart valve (BMHV) is simulated with a
strongly coupled implicit fluid-structure interaction (FSI) method
which is newly organized based on the Arbitrary-Lagrangian-Eulerian
(ALE) approach and the dynamic mesh method (remeshing) of
FLUENT. The simulated results are in good agreement with previous
experimental studies. This study shows the applicability of the present
FSI model to the complicated physics interacting between fluid flow
and moving boundary.
Abstract: We present a BeeBot, Binus Multi-client Intelligent Telepresence Robot, a custom-build robot system specifically designed for teleconference with multiple person using omni directional actuator. The robot is controlled using a computer networks, so the manager/supervisor can direct the robot to the intended person to start a discussion/inspection. People tracking and autonomous navigation are intelligent features of this robot. We build a web application for controlling the multi-client telepresence robot and open-source teleconference system used. Experimental result presented and we evaluated its performance.
Abstract: The angular distribution of Compton scattering of two
quanta originating in the annihilation of a positron with an electron
is investigated as a quantum key distribution (QKD) mechanism in
the gamma spectral range. The geometry of coincident Compton
scattering is observed on the two sides as a way to obtain partially
correlated readings on the quantum channel. We derive the noise
probability density function of a conceptually equivalent prepare
and measure quantum channel in order to evaluate the limits of the
concept in terms of the device secrecy capacity and estimate it at
roughly 1.9 bits per 1 000 annihilation events. The high error rate
is well above the tolerable error rates of the common reconciliation
protocols; therefore, the proposed key agreement protocol by public
discussion requires key reconciliation using classical error-correcting
codes. We constructed a prototype device based on the readily
available monolithic detectors in the least complex setup.
Abstract: Single Minute Exchange of Dies (SMED) mainly focuses on recognition of internal and external activities. It is concerned particularly with transferring internal activities into external ones in as many numbers as possible, by also minimizing the internal ones. The validity of the method and procedures are verified by an application a Styrofoam manufacturing process where setup times are critical for time reduction. Significant time savings have been achieved with minimum investment. Further, the issues related with employer safety and ergonomics principles during die exchange are noted.
Abstract: Composite pins of rubber dust collected from tyre
retreading centres of trucks, cars and buses etc.and epoxy with
weight percentages of 10. 15, and 20 % of rubber (weight fractions of
9, 13 and 17 % respectively) have been prepared in house with the
help of a split wooden mould. The pins were tested in a pin-on-disc
wear monitor to determine the co-efficient of friction and weight
losses with varying speeds, loads and time. The wear volume and
wear rates have also been found out for all these three specimens.. It
is observed that all the specimens have exhibited very low coefficient
of friction and low wear rates under dry sliding condition. Out of the
above three samples tested, the specimen with 10 % rubber dust by
weight has shown lowest wear rates. However a peculiar result i.e
decreasing trend has been obtained with 20% reinforcement of rubber
in epoxy while rubbed against steel at varying speeds. This might
have occurred due to high surface finish of the disc and formation of
a thin transfer layer from the composite
Abstract: It is well known that the channel capacity of Multiple-
Input-Multiple-Output (MIMO) system increases as the number of
antenna pairs between transmitter and receiver increases but it suffers
from multiple expensive RF chains. To reduce the cost of RF chains,
Antenna Selection (AS) method can offer a good tradeoff between
expense and performance. In a transmitting AS system, Channel
State Information (CSI) feedback is necessarily required to choose
the best subset of antennas in which the effects of delays and errors
occurred in feedback channels are the most dominant factors
degrading the performance of the AS method. This paper presents the
concept of AS method using CSI from channel reciprocity instead of
feedback method. Reciprocity technique can easily archive CSI by
utilizing a reverse channel where the forward and reverse channels
are symmetrically considered in time, frequency and location. In this
work, the capacity performance of MIMO system when using AS
method at transmitter with reciprocity channels is investigated by
own developing Testbed. The obtained results show that reciprocity
technique offers capacity close to a system with a perfect CSI and
gains a higher capacity than a system without AS method from 0.9 to
2.2 bps/Hz at SNR 10 dB.
Abstract: Entrepreneurs are important for national labour markets and economies in that they contribute significantly to economic growth as well as provide the majority of jobs and create new ones. According to the Global Entrepreneurship Monitor’s “Report on Women and Entrepreneurship”, investment in women’s entrepreneurship is an important way to exponentially increase the impact of new venture creation finding ways to empower women’s participation and success in entrepreneurship are critical for more sustainable and successful economic development. Our results confirm that they are still differences between men and women entrepreneurs The reasons seems to be the lack of specific business skills, the less extensive social network, and the lack of identification patterns among women. Those differences can be explained by the fact that women still have fewer opportunities to make a career. If this is correct, we can predict an increasing proportion of women among entrepreneurs in the next years. Concerning the development of a favorable environment for developing and enhancing women entrepreneurship activities, our results show the insertion in a network and the role of a model doubtless represent elements determining in the choice to launch an entrepreneurship activity, as well as a precious resource for the success of her company.