Abstract: Requirements that should be met when determining the regimes of circuits with variable elements are formulated. The interpretation of the variations in the regimes, based on projective geometry, enables adequate expressions for determining and comparing the regimes to be derived. It is proposed to use as the parameters of a generalized equivalent generator of an active two-pole with changeable resistor such load current and voltage which provide the current through this resistor equal to zero.
Abstract: Absorptive characteristics of polyaniline synthesized
in mixture of water and acetonitrile in 50/50 volume ratio was
studied. Synthesized polyaniline in powder shape is used as an
adsorbent to remove toxic hexavalent chromium from aqueous
solutions. Experiments were conducted in batch mode with different
variables such as agitation time, solution pH and initial concentration
of hexavalent chromium. Removal mechanism is the combination of
surface adsorption and reduction. The equilibrium time for removal
of Cr(T) and Cr(VI) was about 2 and 10 minutes respectively. The
optimum pH for total chromium removal occurred at pH 7 and
maximum hexavalent chromium removal took place under acidic
condition at pH 3. Investigating the isothermal characteristics showed
that the equilibrium adsorption data fitted both Freundlich-s and
Langmuir-s isotherms. The maximum adsorption of chromium was
calculated 36.1 mg/g for polyaniline
Abstract: In this study, effects of EGR on CO and HC emissions
of a dual fuel HCCI-DI engine are investigated. Tests were
conducted on a single-cylinder variable compression ratio (VCR)
diesel engine with compression ratio of 17.5. Premixed gasoline is
provided by a carburetor connected to intake manifold and equipped
with a screw to adjust premixed air-fuel ratio, and diesel fuel is
injected directly into the cylinder through an injector at pressure of
250 bars. A heater placed at inlet manifold is used to control the
intake charge temperature. Optimal intake charge temperature was
110-115ºC due to better formation of a homogeneous mixture
causing HCCI combustion. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge in HCCI combustion.
Experiments indicated 35 BTDC as the optimum injection timing.
Coolant temperature was maintained 50ºC during the tests. Results
show that increasing engine speed at a constant EGR rate leads to
increase in CO and UHC emissions due to the incomplete
combustion caused by shorter combustion duration and less
homogeneous mixture. Results also show that increasing EGR
reduces the amount of oxygen and leads to incomplete combustion
and therefore increases CO emission due to lower combustion
temperature. HC emission also increases as a result of lower
combustion temperatures.
Abstract: Two-interconnected fluidized bed systems are widely used in various processes such as Fisher-Tropsch, hot gas desulfurization, CO2 capture-regeneration with dry sorbent, chemical-looping combustion, sorption enhanced steam methane reforming, chemical-looping hydrogen generation system, and so on. However, most of two-interconnected fluidized beds systems require riser and/or pneumatic transport line for solid conveying and loopseals or seal-pots for gas sealing, recirculation of solids to the riser, and maintaining of pressure balance. The riser (transport bed) is operated at the high velocity fluidization condition and residence times of gas and solid in the riser are very short. If the reaction rate of catalyst or sorbent is slow, the riser can not ensure sufficient contact time between gas and solid and we have to use two bubbling beds for each reaction to ensure sufficient contact time. In this case, additional riser must be installed for solid circulation. Consequently, conventional two-interconnected fluidized bed systems are very complex, large, and difficult to operate. To solve these problems, a novel two-interconnected fluidized bed system has been developed. This system has two bubbling beds, solid injection nozzles, solid conveying lines, and downcomers. In this study, effects of operating variables on solid circulation rate, gas leakage between two beds have been investigated in a cold mode two-interconnected fluidized bed system. Moreover, long-term operation of continuous solid circulation up to 60 hours has been performed to check feasibility of stable operation.
Abstract: The Yasuj city stream named the Beshar supply
water for different usages such as aquaculture farms , drinking,
agricultural and industrial usages. Fish processing plants
,Agricultural farms, waste water of industrial zones and hospitals
waste water which they are generate by human activity produce a
considerable volume of effluent and when they are released in to the
stream they can effect on the water quality and down stream aquatic
systems. This study was conducted to evaluate the effects of outflow
effluent from different human activity and point and non point
pollution sources on the water quality and health of the Beshar
river next to Yasuj. Yasuj is the biggest and most important city in
the Kohkiloye and Boyerahmad province . The Beshar River is one
of the most important aquatic ecosystems in the upstream of the
Karun watershed in south of Iran which is affected by point and non
point pollutant sources . This study was done in order to evaluate the
effects of human activities on the water quality and health of the
Beshar river. This river is approximately 190 km in length and
situated at the geographical positions of 51° 20' to 51° 48' E and 30°
18' to 30° 52' N it is one of the most important aquatic ecosystems of
Kohkiloye and Boyerahmad province in south-west Iran. In this
research project, five study stations were selected to examine water
pollution in the Beshar River systems. Human activity is now one of
the most important factors affecting on hydrology and water quality
of the Beshar river. Humans use large amounts of resources to sustain
various standards of living, although measures of sustainability are
highly variable depending on how sustainability is defined. The
Beshar river ecosystems are particularly sensitive and vulnerable to
human activities. The water samples were analyzed, then some
important water quality parameters such as pH, dissolve oxygen
(DO), Biochemical Oxygen Demand (BOD5), Chemical Oxygen
Demand (COD), Total Suspended Solids (TDS),Turbidity,
Temperature, Nitrates (NO3) and Phosphates (PO4) were estimated
at the two stations. The results show a downward trend in the water
quality at the down stream of the city. The amounts of
BOD5,COD,TSS,T,Turbidity, NO3 and PO4 in the down stream
stations were considerably more than the station 1. By contrast the
amounts of DO in the down stream stations were less than to the
station 1. However when effluent discharge consequence of human
activities are released into the Beshar river near the city, the quality
of river are decreases and the environmental problems of the river
during the next years are predicted to rise.
Abstract: The objective of this research was to identify the
vegetation-soil relationships in Nodushan arid rangelands of Yazd. 5
sites were selected for measuring the cover of plant species and soil
attributes. Soil samples were taken in 0-10 and 10-80 cm layers. The
species studied were Salsola tomentosa, Salsola arbuscula, Peganum
harmala, Zygophylum eurypterum and Eurotia ceratoides. Canonical
correspondence analysis (CCA) was used to analyze the data. Based
on the CCA results, 74.9 % of vegetation-soil variation was explained
by axis 1-3. Axis 1, 2 and 3 accounted for 27.2%, 24.9 % and 22.8%
of variance respectively. Correlation between axis 1, 2, 3 and speciesedaphic
variables were 0.995, 0.989, 0.981 respectively. Soil texture,
lime, salinity and organic matter significantly influenced the
distribution of these plant species. Determination of soil-vegetation
relationships will be useful for managing and improving rangelands
in arid and semi arid environments.
Abstract: The aim of this study is to find out and analyze the
role of gender and age on the perceptions of students to the distant
online program offered by Vocational High School in Sakarya
University. The research is based on a questionnaire as a mean of
data collection method to find out the role of age and gender on the
student-s perceptions toward online education, and the study
progressed through finding relationships between the variables used
in the data collection instrument. The findings of the analysis
revealed that although the students registered to the online program
by will, they preferred the traditional face-to-face education due to
the difficulty of the nonverbal communication, their incompetence of
using the technology required, and their belief in traditional face-toface
learning more than online education.
Regarding gender, the results showed that the female students
have a better perception of the online education as opposed to the
male students. Regarding age, the results showed that the older the
students are the more is their preference towards attending face-toface
classes.
Abstract: A new OTA-based logarithmic-control variable gain
current amplifier (LCCA) is presented. It consists of two Operational
Transconductance Amplifier (OTA) and two PMOS transistors
biased in weak inversion region. The circuit operates from 0.6V DC
power supply and consumes 0.6 μW. The linear-dB controllable
output range is 43 dB with maximum error less than 0.5dB. The
functionality of the proposed design was confirmed using HSPICE in
0.35μm CMOS process technology.
Abstract: The purpose of this study is to investigate the effects
of modality principles in instructional software among first grade
pupils- achievements in the learning of Arabic Language. Two modes
of instructional software were systematically designed and
developed, audio with images (AI), and text with images (TI). The
quasi-experimental design was used in the study. The sample
consisted of 123 male and female pupils from IRBED Education
Directorate, Jordan. The pupils were randomly assigned to any one of
the two modes. The independent variable comprised the two modes
of the instructional software, the students- achievement levels in the
Arabic Language class and gender. The dependent variable was the
achievements of the pupils in the Arabic Language test. The
theoretical framework of this study was based on Mayer-s Cognitive
Theory of Multimedia Learning. Four hypotheses were postulated
and tested. Analyses of Variance (ANOVA) showed that pupils using
the (AI) mode performed significantly better than those using (TI)
mode. This study concluded that the audio with images mode was an
important aid to learning as compared to text with images mode.
Abstract: Calibration estimation is a method of adjusting the
original design weights to improve the survey estimates by using
auxiliary information such as the known population total (or mean)
of the auxiliary variables. A calibration estimator uses calibrated
weights that are determined to minimize a given distance measure to
the original design weights while satisfying a set of constraints
related to the auxiliary information. In this paper, we propose a new
multivariate calibration estimator for the population mean in the
stratified sampling design, which incorporates information available
for more than one auxiliary variable. The problem of determining the
optimum calibrated weights is formulated as a Mathematical
Programming Problem (MPP) that is solved using the Lagrange
multiplier technique.
Abstract: In this paper a new fast simplification method is presented. Such method realizes Karnough map with large number of variables. In order to accelerate the operation of the proposed method, a new approach for fast detection of group of ones is presented. Such approach implemented in the frequency domain. The search operation relies on performing cross correlation in the frequency domain rather than time one. It is proved mathematically and practically that the number of computation steps required for the presented method is less than that needed by conventional cross correlation. Simulation results using MATLAB confirm the theoretical computations. Furthermore, a powerful solution for realization of complex functions is given. The simplified functions are implemented by using a new desigen for neural networks. Neural networks are used because they are fault tolerance and as a result they can recognize signals even with noise or distortion. This is very useful for logic functions used in data and computer communications. Moreover, the implemented functions are realized with minimum amount of components. This is done by using modular neural nets (MNNs) that divide the input space into several homogenous regions. Such approach is applied to implement XOR function, 16 logic functions on one bit level, and 2-bit digital multiplier. Compared to previous non- modular designs, a clear reduction in the order of computations and hardware requirements is achieved.
Abstract: This paper presents a study of the Taguchi design
application to optimize surface quality in damper inserted end milling
operation. Maintaining good surface quality usually involves
additional manufacturing cost or loss of productivity. The Taguchi
design is an efficient and effective experimental method in which a
response variable can be optimized, given various factors, using
fewer resources than a factorial design. This Study included spindle
speed, feed rate, and depth of cut as control factors, usage of different
tools in the same specification, which introduced tool condition and
dimensional variability. An orthogonal array of L9(3^4)was used;
ANOVA analyses were carried out to identify the significant factors
affecting surface roughness, and the optimal cutting combination was
determined by seeking the best surface roughness (response) and
signal-to-noise ratio. Finally, confirmation tests verified that the
Taguchi design was successful in optimizing milling parameters for
surface roughness.
Abstract: Graph coloring is an important problem in computer
science and many algorithms are known for obtaining reasonably
good solutions in polynomial time. One method of comparing
different algorithms is to test them on a set of standard graphs where
the optimal solution is already known. This investigation analyzes a
set of 50 well known graph coloring instances according to a set of
complexity measures. These instances come from a variety of
sources some representing actual applications of graph coloring
(register allocation) and others (mycieleski and leighton graphs) that
are theoretically designed to be difficult to solve. The size of the
graphs ranged from ranged from a low of 11 variables to a high of
864 variables. The method used to solve the coloring problem was
the square of the adjacency (i.e., correlation) matrix. The results
show that the most difficult graphs to solve were the leighton and the
queen graphs. Complexity measures such as density, mobility,
deviation from uniform color class size and number of block
diagonal zeros are calculated for each graph. The results showed that
the most difficult problems have low mobility (in the range of .2-.5)
and relatively little deviation from uniform color class size.
Abstract: This research was to evaluate a technical feasibility of
making single-layer experimental particleboard panels from bamboo
waste (Dendrocalamus asper Backer) by converting bamboo into
strips, which are used to make laminated bamboo furniture. Variable
factors were density (600, 700 and 800 kg/m3) and temperature of
condition (25, 40 and 55 °C). The experimental panels were tested for
their physical and mechanical properties including modulus of
elasticity (MOE), modulus of rupture (MOR), internal bonding
strength (IB), screw holding strength (SH) and thickness swelling
values according to the procedures defined by Japanese Industrial
Standard (JIS). The test result of mechanical properties showed that
the MOR, MOE and IB values were not in the set criteria, except the
MOR values at the density of 700 kg/m3 at 25 °C and at the density
of 800 kg/m3 at 25 and 40 °C, the IB values at the density of 600
kg/m3, at 40 °C, and at the density of 800 kg/m3 at 55 °C. The SH
values had the test result according to the set standard, except with
the density of 600 kg/m3, at 40 and 55 °C. Conclusively, a valuable
renewable biomass, bamboo waste could be used to manufacture
boards.
Abstract: Nozzle is the main part of various spinning systems
such as air-jet and Murata air vortex systems. Recently, many
researchers worked on the usage of the nozzle on different spinning
systems such as conventional ring and compact spinning systems. In
these applications, primary purpose is to improve the yarn quality. In
present study, it was produced the yarns with two different nozzle
types and determined the changes in yarn properties. In order to
explain the effect of the nozzle, airflow structure in the nozzle was
modelled and airflow variables were determined. In numerical
simulation, ANSYS 12.1 package program and Fluid Flow (CFX)
analysis method was used. As distinct from the literature, Shear
Stress Turbulent (SST) model is preferred. And also air pressure at
the nozzle inlet was measured by electronic mass flow meter and
these values were used for the simulation of the airflow. At last, the
yarn was modelled and the area from where the yarn is passing was
included to the numerical analysis.
Abstract: There have been various methods created based on the regression ideas to resolve the problem of data set containing censored observations, i.e. the Buckley-James method, Miller-s method, Cox method, and Koul-Susarla-Van Ryzin estimators. Even though comparison studies show the Buckley-James method performs better than some other methods, it is still rarely used by researchers mainly because of the limited diagnostics analysis developed for the Buckley-James method thus far. Therefore, a diagnostic tool for the Buckley-James method is proposed in this paper. It is called the renovated Cook-s Distance, (RD* i ) and has been developed based on the Cook-s idea. The renovated Cook-s Distance (RD* i ) has advantages (depending on the analyst demand) over (i) the change in the fitted value for a single case, DFIT* i as it measures the influence of case i on all n fitted values Yˆ∗ (not just the fitted value for case i as DFIT* i) (ii) the change in the estimate of the coefficient when the ith case is deleted, DBETA* i since DBETA* i corresponds to the number of variables p so it is usually easier to look at a diagnostic measure such as RD* i since information from p variables can be considered simultaneously. Finally, an example using Stanford Heart Transplant data is provided to illustrate the proposed diagnostic tool.
Abstract: In this study, the effects of machining parameters on
specific energy during surface grinding of 6061Al-SiC35P
composites are investigated. Vol% of SiC, feed and depth of cut were
chosen as process variables. The power needed for the calculation of
the specific energy is measured from the two watt meter method.
Experiments are conducted using standard RSM design called Central
composite design (CCD). A second order response surface model was
developed for specific energy. The results identify the significant
influence factors to minimize the specific energy. The confirmation
results demonstrate the practicability and effectiveness of the
proposed approach.
Abstract: In this paper real money demand function is analyzed
within multivariate time-series framework. Cointegration approach is
used (Johansen procedure) assuming interdependence between
money demand determinants, which are nonstationary variables. This
will help us to understand the behavior of money demand in Croatia,
revealing the significant influence between endogenous variables in
vector autoregrression system (VAR), i.e. vector error correction
model (VECM). Exogeneity of the explanatory variables is tested.
Long-run money demand function is estimated indicating slow speed
of adjustment of removing the disequilibrium. Empirical results
provide the evidence that real industrial production and exchange
rate explains the most variations of money demand in the long-run,
while interest rate is significant only in short-run.
Abstract: One of the purposes of the robust method of
estimation is to reduce the influence of outliers in the data, on the
estimates. The outliers arise from gross errors or contamination from
distributions with long tails. The trimmed mean is a robust estimate.
This means that it is not sensitive to violation of distributional
assumptions of the data. It is called an adaptive estimate when the
trimming proportion is determined from the data rather than being
fixed a “priori-.
The main objective of this study is to find out the robustness
properties of the adaptive trimmed means in terms of efficiency, high
breakdown point and influence function. Specifically, it seeks to find
out the magnitude of the trimming proportion of the adaptive
trimmed mean which will yield efficient and robust estimates of the
parameter for data which follow a modified Weibull distribution with
parameter λ = 1/2 , where the trimming proportion is determined by a
ratio of two trimmed means defined as the tail length. Secondly, the
asymptotic properties of the tail length and the trimmed means are
also investigated. Finally, a comparison is made on the efficiency of
the adaptive trimmed means in terms of the standard deviation for the
trimming proportions and when these were fixed a “priori".
The asymptotic tail lengths defined as the ratio of two trimmed
means and the asymptotic variances were computed by using the
formulas derived. While the values of the standard deviations for the
derived tail lengths for data of size 40 simulated from a Weibull
distribution were computed for 100 iterations using a computer
program written in Pascal language.
The findings of the study revealed that the tail lengths of the
Weibull distribution increase in magnitudes as the trimming
proportions increase, the measure of the tail length and the adaptive
trimmed mean are asymptotically independent as the number of
observations n becomes very large or approaching infinity, the tail
length is asymptotically distributed as the ratio of two independent
normal random variables, and the asymptotic variances decrease as
the trimming proportions increase. The simulation study revealed
empirically that the standard error of the adaptive trimmed mean
using the ratio of tail lengths is relatively smaller for different values
of trimming proportions than its counterpart when the trimming
proportions were fixed a 'priori'.
Abstract: In this study arsenate [As(V)] removal from drinking water by coagulation process was investigated. Ferric chloride (FeCl3.6H2O) and ferrous sulfate (FeSO4.7H2O) were used as coagulant. The effects of major operating variables such as coagulant dose (1–30 mg/L) and pH (5.5–9.5) were investigated. Ferric chloride and ferrous sulfate were found as effective and reliable coagulant due to required dose, residual arsenate and coagulant concentration. Optimum pH values for maximum arsenate removal for ferrous sulfate and ferric chloride were found as 8 and 7.5. The arsenate removal efficiency decreased at neutral and acidic pH values for Fe(II) and at the high acidic and high alkaline pH for Fe(III). It was found that the increase of coagulant dose caused a substantial increase in the arsenate removal. But above a certain ferric chloride and ferrous sulfate dosage, the increase in arsenate removal was not significant. Ferric chloride and ferrous sulfate dose above 8 mg/L slightly increased arsenate removal.