Abstract: This report shows the performance of composite
biodegradable film from chitosan, starch and sawdust fiber. The main
objectives of this research are to fabricate and characterize composite
biodegradable film in terms of morphology and physical properties.
The film was prepared by casting method. Sawdust fiber was used as
reinforcing agent and starch as polymer matrix in the casting
solution. The morphology of the film was characterized using atomic
force microscope (AFM). The result showed that the film has
smooth structure. Chemical composition of the film was investigated
using Fourier transform infrared (FTIR) where the result revealed
present of starch in the film. The thermal properties were
characterized using thermal gravimetric analyzer (TGA) and
differential scanning calorimetric (DSC) where the results showed
that the film has small difference in melting and degradation
temperature.
Abstract: Fixed-point simulation results are used for the
performance measure of inverting matrices by Cholesky
decomposition. The fixed-point Cholesky decomposition algorithm
is implemented using a fixed-point reconfigurable processing
element. The reconfigurable processing element provides all
mathematical operations required by Cholesky decomposition. The
fixed-point word length analysis is based on simulations using
different condition numbers and different matrix sizes. Simulation
results show that 16 bits word length gives sufficient performance
for small matrices with low condition number. Larger matrices and
higher condition numbers require more dynamic range for a fixedpoint
implementation.
Abstract: In this paper is investigated a possible
optimization of some linear algebra problems which can be
solved by parallel processing using the special arrays called
systolic arrays. In this paper are used some special types of
transformations for the designing of these arrays. We show
the characteristics of these arrays. The main focus is on
discussing the advantages of these arrays in parallel
computation of matrix product, with special approach to the
designing of systolic array for matrix multiplication.
Multiplication of large matrices requires a lot of
computational time and its complexity is O(n3 ). There are
developed many algorithms (both sequential and parallel) with
the purpose of minimizing the time of calculations. Systolic
arrays are good suited for this purpose. In this paper we show
that using an appropriate transformation implicates in finding
more optimal arrays for doing the calculations of this type.
Abstract: This paper presents a computational methodology
based on matrix operations for a computer based solution to the
problem of performance analysis of software reliability models
(SRMs). A set of seven comparison criteria have been formulated to
rank various non-homogenous Poisson process software reliability
models proposed during the past 30 years to estimate software
reliability measures such as the number of remaining faults, software
failure rate, and software reliability. Selection of optimal SRM for
use in a particular case has been an area of interest for researchers in
the field of software reliability. Tools and techniques for software
reliability model selection found in the literature cannot be used with
high level of confidence as they use a limited number of model
selection criteria. A real data set of middle size software project from
published papers has been used for demonstration of matrix method.
The result of this study will be a ranking of SRMs based on the
Permanent value of the criteria matrix formed for each model based
on the comparison criteria. The software reliability model with
highest value of the Permanent is ranked at number – 1 and so on.
Abstract: In this paper a new definition of adjacency matrix in
the simple graphs is presented that is called fuzzy adjacency matrix,
so that elements of it are in the form of 0 and
n N
n
1 , ∈
that are
in the interval [0, 1], and then some charactristics of this matrix are
presented with the related examples . This form matrix has complete
of information of a graph.
Abstract: Octree compression techniques have been used
for several years for compressing large three dimensional data
sets into homogeneous regions. This compression technique
is ideally suited to datasets which have similar values in
clusters. Oil engineers represent reservoirs as a three dimensional
grid where hydrocarbons occur naturally in clusters. This
research looks at the efficiency of storing these grids using
octree compression techniques where grid cells are broken
into active and inactive regions. Initial experiments yielded
high compression ratios as only active leaf nodes and their
ancestor, header nodes are stored as a bitstream to file on
disk. Savings in computational time and memory were possible
at decompression, as only active leaf nodes are sent to the
graphics card eliminating the need of reconstructing the original
matrix. This results in a more compact vertex table, which can
be loaded into the graphics card quicker and generating shorter
refresh delay times.
Abstract: This study created new graphical icons and operating
functions in a CAD/CAM software system by analyzing icons in some
of the popular systems, such as AutoCAD, AlphaCAM, Mastercam
and the 1st edition of LiteCAM. These software systems all focused on
geometric design and editing, thus how to transmit messages
intuitively from icon itself to users is an important function of
graphical icons. The primary purpose of this study is to design
innovative icons and commands for new software.
This study employed the TRIZ method, an innovative design
method, to generate new concepts systematically. Through literature
review, it then investigated and analyzed the relationship between
TRIZ and idea development. Contradiction Matrix and 40 Principles
were used to develop an assisting tool suitable for icon design in
software development. We first gathered icon samples from the
selected CAD/CAM systems. Then grouped these icons by
meaningful functions, and compared useful and harmful properties.
Finally, we developed new icons for new software systems in order to
avoid intellectual property problem.
Abstract: The dynamic or complex modulus test is considered
to be a mechanistically based laboratory test to reliably characterize
the strength and load-resistance of Hot-Mix Asphalt (HMA) mixes
used in the construction of roads. The most common observation is
that the data collected from these tests are often noisy and somewhat
non-sinusoidal. This hampers accurate analysis of the data to obtain
engineering insight. The goal of the work presented in this paper is to
develop and compare automated evolutionary computational
techniques to filter test noise in the collection of data for the HMA
complex modulus test. The results showed that the Covariance
Matrix Adaptation-Evolutionary Strategy (CMA-ES) approach is
computationally efficient for filtering data obtained from the HMA
complex modulus test.
Abstract: A preconditioned Jacobi (PJ) method is provided for solving fuzzy linear systems whose coefficient matrices are crisp Mmatrices and the right-hand side columns are arbitrary fuzzy number vectors. The iterative algorithm is given for the preconditioned Jacobi method. The convergence is analyzed with convergence theorems. Numerical examples are given to illustrate the procedure and show the effectiveness and efficiency of the method.
Abstract: The integral form of equations of motion of composite
beams subjected to varying time loads are discretized using a
developed finite element model. The model consists of a straight five
node twenty-two degrees of freedom beam element. The stability
analysis of the beams is studied by solving the matrix form
characteristic equations of the system. The principle of virtual work
and the first order shear deformation theory are employed to analyze
the beams with large deformation and small strains. The regions of
dynamic instability of the beam are determined by solving the
obtained Mathieu form of differential equations. The effects of nonconservative
loads, shear stiffness, and damping parameters on
stability and response of the beams are examined. Several numerical
calculations are presented to compare the results with data reported
by other researchers.
Abstract: A climate dependent model is proposed to simulate
the population of Aedes aegypti mosquito. In developing the model,
average temperature of Shah Alam, Malaysia was used to determine
the development rate of each stage of the life cycle of mosquito.
Rainfall dependent function was proposed to simulate the hatching
rate of the eggs under several assumptions. The proposed transition
matrix was obtained and used to simulate the population of eggs,
larvae, pupae and adults mosquito. It was found that the peak of
mosquito abundance comes during a relatively dry period following a
heavy rainfall. In addition, lag time between the peaks of mosquito
abundance and dengue fever cases in Shah Alam was estimated.
Abstract: Quality control charts are very effective in detecting
out of control signals but when a control chart signals an out of
control condition of the process mean, searching for a special cause
in the vicinity of the signal time would not always lead to prompt
identification of the source(s) of the out of control condition as the
change point in the process parameter(s) is usually different from the
signal time. It is very important to manufacturer to determine at what
point and which parameters in the past caused the signal. Early
warning of process change would expedite the search for the special
causes and enhance quality at lower cost. In this paper the quality
variables under investigation are assumed to follow a multivariate
normal distribution with known means and variance-covariance
matrix and the process means after one step change remain at the new
level until the special cause is being identified and removed, also it is
supposed that only one variable could be changed at the same time.
This research applies artificial neural network (ANN) to identify the
time the change occurred and the parameter which caused the change
or shift. The performance of the approach was assessed through a
computer simulation experiment. The results show that neural
network performs effectively and equally well for the whole shift
magnitude which has been considered.
Abstract: This paper is concerned with the delay-distributiondependent
stability criteria for bidirectional associative memory
(BAM) neural networks with time-varying delays. Based on the
Lyapunov-Krasovskii functional and stochastic analysis approach,
a delay-probability-distribution-dependent sufficient condition is derived
to achieve the globally asymptotically mean square stable of
the considered BAM neural networks. The criteria are formulated in
terms of a set of linear matrix inequalities (LMIs), which can be
checked efficiently by use of some standard numerical packages. Finally,
a numerical example and its simulation is given to demonstrate
the usefulness and effectiveness of the proposed results.
Abstract: In this paper, based on the estimation of the Cauchy matrix of linear impulsive differential equations, by using Banach fixed point theorem and Gronwall-Bellman-s inequality, some sufficient conditions are obtained for the existence and exponential stability of almost periodic solution for Cohen-Grossberg shunting inhibitory cellular neural networks (SICNNs) with continuously distributed delays and impulses. An example is given to illustrate the main results.
Abstract: We present a new method for the fully automatic 3D
reconstruction of the coronary artery centerlines, using two X-ray
angiogram projection images from a single rotating monoplane
acquisition system. During the first stage, the input images are
smoothed using curve evolution techniques. Next, a simple yet
efficient multiscale method, based on the information of the Hessian
matrix, for the enhancement of the vascular structure is introduced.
Hysteresis thresholding using different image quantiles, is used to
threshold the arteries. This stage is followed by a thinning procedure
to extract the centerlines. The resulting skeleton image is then pruned
using morphological and pattern recognition techniques to remove
non-vessel like structures. Finally, edge-based stereo correspondence
is solved using a parallel evolutionary optimization method based on
f symbiosis. The detected 2D centerlines combined with disparity
map information allow the reconstruction of the 3D vessel
centerlines. The proposed method has been evaluated on patient data
sets for evaluation purposes.
Abstract: In this study, an ablation, mechanical and thermal properties of a rocket motor insulation from phenolic/ fiber matrix composites forming a laminate with different fiber between fiberglass and locally available synthetic fibers. The phenolic/ fiber matrix composites was mechanics and thermal properties by means of tensile strength, ablation, TGA and DSC. The design of thermal insulation involves several factors.Determined the mechanical properties according to MIL-I-24768: Density >1.3 g/cm3, Tensile strength >103 MPa and Ablation
Abstract: This paper deals with the localization of the wideband sources. We develop a new approach for estimating the wide band sources parameters. This method is based on the high order statistics of the recorded data in order to eliminate the Gaussian components from the signals received on the various hydrophones.In fact the noise of sea bottom is regarded as being Gaussian. Thanks to the coherent signal subspace algorithm based on the cumulant matrix of the received data instead of the cross-spectral matrix the wideband correlated sources are perfectly located in the very noisy environment. We demonstrate the performance of the proposed algorithm on the real data recorded during an underwater acoustics experiments.
Abstract: MC (Management Control)& IC (Internal Control) – what is the relationship? (an empirical study into the definitions between MC and IC) based on the wider considerations of Internal Control and Management Control terms, attention is focused not only on the financial aspects but also more on the soft aspects of the business, such as culture, behaviour, standards and values. The limited considerations of Management Control are focused mainly in the hard, financial aspects of business operation. The definitions of Management Control and Internal Control are often used interchangeably and the results of this empirical study reveal that Management Control is part of Internal Control, there is no causal link between the two concepts. Based on the interpretation of the respondents, the term Management Control has moved from a broad term to a more limited term with the soft aspects of the influencing of behaviour, performance measurements, incentives and culture. This paper is an exploratory study based on qualitative research and on a qualitative matrix method analysis of the thematic definition of the terms Management Control and Internal Control.
Abstract: The paper focuses on the enhanced stiffness modeling
of robotic manipulators by taking into account influence of the external force/torque acting upon the end point. It implements the
virtual joint technique that describes the compliance of manipulator elements by a set of localized six-dimensional springs separated by
rigid links and perfect joints. In contrast to the conventional
formulation, which is valid for the unloaded mode and small
displacements, the proposed approach implicitly assumes that the loading leads to the non-negligible changes of the manipulator posture and corresponding amendment of the Jacobian. The
developed numerical technique allows computing the static
equilibrium and relevant force/torque reaction of the manipulator for
any given displacement of the end-effector. This enables designer
detecting essentially nonlinear effects in elastic behavior of
manipulator, similar to the buckling of beam elements. It is also proposed the linearization procedure that is based on the inversion of
the dedicated matrix composed of the stiffness parameters of the
virtual springs and the Jacobians/Hessians of the active and passive
joints. The developed technique is illustrated by an application example that deals with the stiffness analysis of a parallel
manipulator of the Orthoglide family
Abstract: ICA which is generally used for blind source separation
problem has been tested for feature extraction in Speech recognition
system to replace the phoneme based approach of MFCC. Applying
the Cepstral coefficients generated to ICA as preprocessing has
developed a new signal processing approach. This gives much better
results against MFCC and ICA separately, both for word and speaker
recognition. The mixing matrix A is different before and after MFCC
as expected. As Mel is a nonlinear scale. However, cepstrals
generated from Linear Predictive Coefficient being independent
prove to be the right candidate for ICA. Matlab is the tool used for
all comparisons. The database used is samples of ISOLET.