Abstract: The storage of chemical fertilizers in concrete building often leads to durability problems due to chemical attack. The damage of concrete is mostly caused by certain ammonium salts. The main purpose of the research is to investigate the durability properties of concrete being exposed to ammonium nitrate solution. In this investigation, experiments are conducted on concrete type G50 and G60. The leaching process is achieved by the use of 20% concentration solution of ammonium nitrate. The durability properties investigated are water absorption, volume of permeable voids, and sorptivity. Compressive strength, pH value, and degradation depth are measured after a certain period of leaching. A decrease in compressive strength and an increase in porosity are found through the conducted experiments. Apart from that, the experimental data shows that pH value decreases with increased leaching time while the degradation depth of concrete increases with leaching time. By comparing concrete type G50 and G60, concrete type G60 is more resistant to ammonium nitrate attack.
Abstract: The adaptive power control of Code Division Multiple
Access (CDMA) communications using Remote Radio Head
(RRH) between multiple Unmanned Aerial Vehicles (UAVs) with
a link-budget based Signal-to-Interference Ratio (SIR) estimate is
applied to four inner loop power control algorithms. It is concluded
that Base Station (BS) can calculate not only UAV distance using
linearity between speed and Consecutive Transmit-Power-Control
Ratio (CTR) of Adaptive Step-size Closed Loop Power Control (ASCLPC),
Consecutive TPC Ratio Step-size Closed Loop Power Control
(CS-CLPC), Fixed Step-size Power Control (FSPC), but also UAV
position with Received Signal Strength Indicator (RSSI) ratio of
RRHs.
Abstract: The paper presents the potential for RES in Romania
and the results of the Romanian national research project “Romania
contribution to the European targets regarding the development of
renewable energy sources - PROMES". The objective of the project
is the development of energy generation from renewable energy
sources (RES) in Romania by drawing up scenarios and prognosis
harmonized with national and European targets, RES development
effects modeling (environmental, economic, social etc.), research of
the impact of the penetration of RES into the main, implementation
of an advanced software system tool for RES information recording
and communication, experimental research based on demonstrative
applications.
The expected results are briefly presented, as well as the social,
economic and environmental impact.
Abstract: We discuss the application of matching in the area of resource discovery and resource allocation in grid computing. We present a formal definition of matchmaking, overview algorithms to evaluate different matchmaking expressions, and develop a matchmaking service for an intelligent grid environment.
Abstract: Removal of Methylene Blue (MB) from aqueous
solution by adsorbing it on Gypsum was investigated by batch
method. The studies were conducted at 25°C and included the effects
of pH and initial concentration of Methylene Blue. The adsorption
data was analyzed by using the Langmuir, Freundlich and Tempkin
isotherm models. The maximum monolayer adsorption capacity was
found to be 36 mg of the dye per gram of gypsum. The data were
also analyzed in terms of their kinetic behavior and was found to
obey the pseudo second order equation.
Abstract: The Long-range Energy and Alternatives Planning (LEAP) energy planning system has been developed for South Africa, for the 2005 base year and a limited number of plausible future scenarios that may have significant implications (negative or positive) in terms of environmental impacts. The system quantifies the national energy demand for the domestic, commercial, transport, industry and agriculture sectors, the supply of electricity and liquid fuels, and the resulting emissions. The South African National Energy Research Institute (SANERI) identified the need to develop an environmental assessment tool, based on the LEAP energy planning system, to provide decision-makers and stakeholders with the necessary understanding of the environmental impacts associated with different energy scenarios. A comprehensive analysis of indicators that are used internationally and in South Africa was done and the available data was accessed to select a reasonable number of indicators that could be utilized in energy planning. A consultative process was followed to determine the needs of different stakeholders on the required indicators and also the most suitable form of reporting. This paper demonstrates the application of Energy Environmental Sustainability Indicators (EESIs) as part of the developed tool, which assists with the identification of the environmental consequences of energy generation and use scenarios and thereby promotes sustainability, since environmental considerations can then be integrated into the preparation and adoption of policies, plans, programs and projects. Recommendations are made to refine the tool further for South Africa.
Abstract: This paper presents a integer frequency offset (IFO)
estimation scheme for the 3GPP long term evolution (LTE) downlink
system. Firstly, the conventional joint detection method for IFO and
sector cell index (CID) information is introduced. Secondly, an IFO
estimation without explicit sector CID information is proposed, which
can operate jointly with the proposed IFO estimation and reduce
the time delay in comparison with the conventional joint method.
Also, the proposed method is computationally efficient and has almost
similar performance in comparison with the conventional method over
the Pedestrian and Vehicular channel models.
Abstract: Petrol Fuel Station (PFS) has potential hazards to the
people, asset, environment and reputation of an operating company.
Fire hazards, static electricity air pollution evoked by aliphatic and
aromatic organic compounds are major causes of accident/incident
occurrence at fuel station. Activities such as carelessness,
maintenance, housekeeping, slips trips and falls, transportation
hazard, major and minor injuries, robbery and snake bites has a
potential to create unsafe conditions. The level of risk of these
hazards varies according to location and country. The emphasis on
safety considerations by the government is variable all around the
world. Developed countries safety records are much better as
compared to developing countries safety statistics. There is no
significant approach available to highlight the unsafe acts and unsafe
conditions during operation and maintenance of fuel station. Fuel
station is the most commonly available facilities that contain
flammable and hazardous materials. Due to continuous operation of
fuel station they pose various hazards to people, environment and
assets of an organization. To control these hazards, there is a need for
specific approach. PFS operation is unique as compared to other
businesses. For smooth operations it demands an involvement of
operating company, contractor and operator group. This study will
focus to address hazard contributing factors that have a potential to
make PFS operation risky. One year data collected, 902 activities
analyzed, comparisons were made to highlight significant
contributing factors. The study will provide help and assistance to
PFS outlet marketing companies to make their fuel station operation
safer. It will help health safety and environment (HSE) professionals
to arrest the gap available related to safety matters at PFS.
Abstract: In the numerical solution of the forward dynamics of a
multibody system, the positions and velocities of the bodies in the
system are obtained first. With the information of the system state
variables at each time step, the internal and external forces acting on
the system are obtained by appropriate contact force models if the
continuous contact method is used instead of a discrete contact
method. The local deformation of the bodies in contact, represented
by penetration, is used to compute the contact force. The ability and
suitability with current cylindrical contact force models to describe
the contact between bodies with cylindrical geometries with
particular focus on internal contacting geometries involving low
clearances and high loads simultaneously is discussed in this paper.
A comparative assessment of the performance of each model under
analysis for different contact conditions, in particular for very
different penetration and clearance values, is presented. It is
demonstrated that some models represent a rough approximation to
describe the conformal contact between cylindrical geometries
because contact forces are underestimated.
Abstract: In this paper, we present the region based hidden Markov random field model (RBHMRF), which encodes the characteristics of different brain regions into a probabilistic framework for brain MR image segmentation. The recently proposed TV+L1 model is used for region extraction. By utilizing different spatial characteristics in different brain regions, the RMHMRF model performs beyond the current state-of-the-art method, the hidden Markov random field model (HMRF), which uses identical spatial information throughout the whole brain. Experiments on both real and synthetic 3D MR images show that the segmentation result of the proposed method has higher accuracy compared to existing algorithms.
Abstract: In a previous work, we presented the numerical
solution of the two dimensional second order telegraph partial
differential equation discretized by the centred and rotated five-point
finite difference discretizations, namely the explicit group (EG) and
explicit decoupled group (EDG) iterative methods, respectively. In
this paper, we utilize a domain decomposition algorithm on these
group schemes to divide the tasks involved in solving the same
equation. The objective of this study is to describe the development
of the parallel group iterative schemes under OpenMP programming
environment as a way to reduce the computational costs of the
solution processes using multicore technologies. A detailed
performance analysis of the parallel implementations of points and
group iterative schemes will be reported and discussed.
Abstract: Perennial ryegrass (Lolium perenne L.) plants are cultivated for lawn constitution and as forage plants. Considerable number of perennial ryegrass genotypes are present in the flora of our country and they present substantial was performed based on a Project supported bu TUBITAK (Project numver : 106O159) and perannial ryegrass genotypes from 8 provinces were collected during 2006. Seeds of perennial ryegrass were collected from 48 different locations. Populations of turfgrass seeds in flowerpots to be 20 and 1 cm deep greenhouse were sown in three replications at 07.07.2007.Then the growth of turfgrass seedlings in the greenhouse in pots showed sufficiently separated from the plants were planted in each population. Plants planted in the garden of the observation scale of 1-9 was evaluated by the quality, 1 = the weakest / worst, 6 = acceptable and 9 = superior or considered as an ideal. Essentially only recognized in assessing the quality of the color of grass, but the color, density, uniformity, texture (texture), illness or environmental stresses are evaluated as a combination reaction. Turfgrass quality 15.11.2007, 19.03.2008, 27.05.2008, 27.11.2008, 07.03.2009 and 02.06.2009 have been 6 times to be in order. Observations made regarding the quality of grass; 3 years according to seasonal environments turf quality genotypes belonging to 14 different populations were found to be 7.5 and above are reserved for future use in breeding works.The number of genotypes belonging to 41 populations in terms of turfgrass quality was determined as 7.9 of 3 year average seasonal. Argıthan between Doğanhisar (Konya) is located 38.09 latitude and 31.40 longitude, altitude 1158 m in the set that population numbered 41.
Abstract: Oxidative stress makes up common incidents in
eukaryotic metabolism. The presence of diverse components
disturbing the equilibrium during oxygen metabolism increases
oxidative damage unspecifically in living cells. Body´s own
ubiquinone (Q10) seems to be a promising drug in defending the
heightened appearance of reactive oxygen species (ROS). Though, its
lipophilic properties require a new strategy in drug formulation to
overcome their low bioavailability. Consequently, the manufacture of
heterogeneous nanodispersions is in focus for medical applications.
The composition of conventional nanodispersions is made up of a
drug-consisting core and a surfactive agent, also named as surfactant.
Long-termed encapsulation of the surfactive components into tissues
might be the consequence of the use during medical therapeutics. The
potential of provoking side-effects is given by their nonbiodegradable
properties. Further improvements during fabrication
process use the incorporation of biodegradable components such as
modified γ-polyglutamic acid which decreases the potential of
prospective side-effects.
Abstract: Lanthanide-doped upconversion nanoparticles which can convert near-infrared lights to visible lights have attracted growing interest because of their great potentials in fluorescence imaging. Upconversion fluorescence imaging technique with excitation in the near-infrared (NIR) region has been used for imaging of biological cells and tissues. However, improving the detection sensitivity and decreasing the absorption and scattering in biological tissues are as yet unresolved problems. In this present study, a novel NIR-reflected multispectral imaging system was developed for upconversion fluorescent imaging in small animals. Based on this system, we have obtained the high contrast images without the autofluorescence when biocompatible UCPs were injected near the body surface or deeply into the tissue. Furthermore, we have extracted respective spectra of the upconversion fluorescence and relatively quantify the fluorescence intensity with the multispectral analysis. To our knowledge, this is the first time to analyze and quantify the upconversion fluorescence in the small animal imaging.
Abstract: This paper provides an introduction into the evolution
of information and communication technology and illustrates its
usage in the work domain. The paper is sub-divided into two parts.
The first part gives an overview over the different phases of
information processing in the work domain. It starts by charting the
past and present usage of computers in work environments and shows
current technological trends, which are likely to influence future
business applications. The second part starts by briefly describing,
how the usage of computers changed business processes in the past,
and presents first Ambient Intelligence applications based on
identification and localization information, which are already used in
the production and retail sector. Based on current systems and
prototype applications, the paper gives an outlook of how Ambient
Intelligence technologies could change business processes in the
future.
Abstract: Using spatial models as a shared common basis of
information about the environment for different kinds of contextaware
systems has been a heavily researched topic in the last years.
Thereby the research focused on how to create, to update, and to
merge spatial models so as to enable highly dynamic, consistent and
coherent spatial models at large scale. In this paper however, we
want to concentrate on how context-aware applications could use this
information so as to adapt their behavior according to the situation
they are in. The main idea is to provide the spatial model
infrastructure with a situation recognition component based on
generic situation templates. A situation template is – as part of a
much larger situation template library – an abstract, machinereadable
description of a certain basic situation type, which could be
used by different applications to evaluate their situation. In this
paper, different theoretical and practical issues – technical, ethical
and philosophical ones – are discussed important for understanding
and developing situation dependent systems based on situation
templates. A basic system design is presented which allows for the
reasoning with uncertain data using an improved version of a
learning algorithm for the automatic adaption of situation templates.
Finally, for supporting the development of adaptive applications, we
present a new situation-aware adaptation concept based on
workflows.
Abstract: Lactic acid alone and its combined application with
nisin were evaluated for reducing population of naturally occurring
microorganisms on chilled shrimp. Fresh shrimps were dipped in 0,
1.0% and 2.0% (v/v) lactic acid alone and their combined application
with 0.04 (g/L/kg) nisin solution for 10 min. Total plate counts of
aerobic bacteria (TPCs), Psychrotrophic counts, population of
Pseudomonas spp., H2S producing bacteria and Lactic acid bacteria
(LAB) on shrimps were determined during storage at 4 °C. The
results indicated that total plate counts were 2.91 and 2.63 log CFU/g
higher on untreated shrimps after 7 and 14 days of storage,
respectively, than on shrimps treated with 2.0% lactic acid combined
with 0.04 (g/L/kg) nisin. Both concentrations of lactic acid indicated
significant reduction on Pseudomonas counts during storage, while
2.0% lactic acid combined with nisin indicated the highest reduction.
In addition, H2S producing bacteria were more sensitive to high
concentration of lactic acid combined with nisin during storage.
Abstract: The identification and elimination of bad
measurements is one of the basic functions of a robust state estimator
as bad data have the effect of corrupting the results of state
estimation according to the popular weighted least squares method.
However this is a difficult problem to handle especially when dealing
with multiple errors from the interactive conforming type. In this
paper, a self adaptive genetic based algorithm is proposed. The
algorithm utilizes the results of the classical linearized normal
residuals approach to tune the genetic operators thus instead of
making a randomized search throughout the whole search space it is
more likely to be a directed search thus the optimum solution is
obtained at very early stages(maximum of 5 generations). The
algorithm utilizes the accumulating databases of already computed
cases to reduce the computational burden to minimum. Tests are
conducted with reference to the standard IEEE test systems. Test
results are very promising.
Abstract: Incompressible Navier-Stokes equations are reviewed
in this work. Three-dimensional Navier-Stokes equations are solved
analytically. The Mathematical derivation shows that the solutions
for the zero and constant pressure gradients are similar. Descriptions
of the proposed formulation and validation against two laminar
experiments and three different turbulent flow cases are reported in
this paper. Even though, the analytical solution is derived for nonreacting
flows, it could reproduce trends for cases including
combustion.
Abstract: This paper discusses the novel graphical approach for
stability analysis of multi induction motor drive controlled by a single
inverter. Stability issue arises in parallel connected induction motors
under unbalanced load conditions. The two powerful globally
accepted modeling and simulation software packages such as
MATLAB and LabVIEW are selected to perform the stability
analysis. The stability investigation is performed for different load
conditions and difference in stator and rotor resistances among the
two motors. It is very simple and effective than the techniques
presented to obtain the stability of the parallel connected induction
motor drive under unbalanced load conditions. Approximate transfer
functions are considered to model the induction motors, load
dynamics, speed controllers and inverter. Simulink library tools are
utilized to model the entire drive scheme in MATLAB. Stability
study is discussed in LabVIEW using control design and simulation
toolkits. Simulation results are illustrated for various running
conditions to demonstrate the effectiveness of the transfer function
method.