Abstract: The design of a pattern classifier includes an attempt
to select, among a set of possible features, a minimum subset of
weakly correlated features that better discriminate the pattern classes.
This is usually a difficult task in practice, normally requiring the
application of heuristic knowledge about the specific problem
domain. The selection and quality of the features representing each
pattern have a considerable bearing on the success of subsequent
pattern classification. Feature extraction is the process of deriving
new features from the original features in order to reduce the cost of
feature measurement, increase classifier efficiency, and allow higher
classification accuracy. Many current feature extraction techniques
involve linear transformations of the original pattern vectors to new
vectors of lower dimensionality. While this is useful for data
visualization and increasing classification efficiency, it does not
necessarily reduce the number of features that must be measured
since each new feature may be a linear combination of all of the
features in the original pattern vector. In this paper a new approach is
presented to feature extraction in which feature selection, feature
extraction, and classifier training are performed simultaneously using
a genetic algorithm. In this approach each feature value is first
normalized by a linear equation, then scaled by the associated weight
prior to training, testing, and classification. A knn classifier is used to
evaluate each set of feature weights. The genetic algorithm optimizes
a vector of feature weights, which are used to scale the individual
features in the original pattern vectors in either a linear or a nonlinear
fashion. By this approach, the number of features used in classifying
can be finely reduced.
Abstract: A new approach based on the consideration that electroencephalogram (EEG) signals are chaotic signals was presented for automated diagnosis of electroencephalographic changes. This consideration was tested successfully using the nonlinear dynamics tools, like the computation of Lyapunov exponents. This paper presented the usage of statistics over the set of the Lyapunov exponents in order to reduce the dimensionality of the extracted feature vectors. Since classification is more accurate when the pattern is simplified through representation by important features, feature extraction and selection play an important role in classifying systems such as neural networks. Multilayer perceptron neural network (MLPNN) architectures were formulated and used as basis for detection of electroencephalographic changes. Three types of EEG signals (EEG signals recorded from healthy volunteers with eyes open, epilepsy patients in the epileptogenic zone during a seizure-free interval, and epilepsy patients during epileptic seizures) were classified. The selected Lyapunov exponents of the EEG signals were used as inputs of the MLPNN trained with Levenberg- Marquardt algorithm. The classification results confirmed that the proposed MLPNN has potential in detecting the electroencephalographic changes.
Abstract: An adaptive neural network controller for
autonomous underwater vehicles (AUVs) is presented in this paper.
The AUV model is highly nonlinear because of many factors, such as
hydrodynamic drag, damping, and lift forces, Coriolis and centripetal
forces, gravity and buoyancy forces, as well as forces from thruster.
In this regards, a nonlinear neural network is used to approximate the
nonlinear uncertainties of AUV dynamics, thus overcoming some
limitations of conventional controllers and ensure good performance.
The uniform ultimate boundedness of AUV tracking errors and the
stability of the proposed control system are guaranteed based on
Lyapunov theory. Numerical simulation studies for motion control of
an AUV are performed to demonstrate the effectiveness of the
proposed controller.
Abstract: Programmable logic controllers are the main controllers in the today's industries; they are used for several applications in industrial control systems and there are lots of examples exist from the PLC applications in industries especially in big companies and plants such as refineries, power plants, petrochemical companies, steel companies, and food and production companies. In the PLCs there are some functions in the function library in software that can be used in PLC programs as basic program elements. The aim of this project are introducing and implementing a new function block of a neural network to the function library of PLC. This block can be applied for some control applications or nonlinear functions calculations after it has been trained for these applications. The implemented neural network is a Perceptron neural network with three layers, three input nodes and one output node. The block can be used in manual or automatic mode. In this paper the structure of the implemented function block, the parameters and the training method of the network are presented by considering the especial method of PLC programming and its complexities. Finally the application of the new block is compared with a classic simulated block and the results are presented.
Abstract: This paper introduces a new signal denoising based on the Empirical mode decomposition (EMD) framework. The method is a fully data driven approach. Noisy signal is decomposed adaptively into oscillatory components called Intrinsic mode functions (IMFs) by means of a process called sifting. The EMD denoising involves filtering or thresholding each IMF and reconstructs the estimated signal using the processed IMFs. The EMD can be combined with a filtering approach or with nonlinear transformation. In this work the Savitzky-Golay filter and shoftthresholding are investigated. For thresholding, IMF samples are shrinked or scaled below a threshold value. The standard deviation of the noise is estimated for every IMF. The threshold is derived for the Gaussian white noise. The method is tested on simulated and real data and compared with averaging, median and wavelet approaches.
Abstract: In the LFC problem, the interconnections among some areas are the input of disturbances, and therefore, it is important to suppress the disturbances by the coordination of governor systems. In contrast, tie-line power flow control by TCPS located between two areas makes it possible to stabilize the system frequency oscillations positively through interconnection, which is also expected to provide a new ancillary service for the further power systems. Thus, a control strategy using controlling the phase angle of TCPS is proposed for provide active control facility of system frequency in this paper. Also, the optimum adjustment of PID controller's parameters in a robust way under bilateral contracted scenario following the large step load demands and disturbances with and without TCPS are investigated by Particle Swarm Optimization (PSO), that has a strong ability to find the most optimistic results. This newly developed control strategy combines the advantage of PSO and TCPS and has simple stricture that is easy to implement and tune. To demonstrate the effectiveness of the proposed control strategy a three-area restructured power system is considered as a test system under different operating conditions and system nonlinearities. Analysis reveals that the TCPS is quite capable of suppressing the frequency and tie-line power oscillations effectively as compared to that obtained without TCPS for a wide range of plant parameter changes, area load demands and disturbances even in the presence of system nonlinearities.
Abstract: New nondestructive technique, namely an inverse technique based on vibration tests, to characterize nonlinear mechanical properties of adhesive layers in sandwich composites is developed. An adhesive layer is described as a viscoelastic isotropic material with storage and loss moduli which are both frequency dependent values in wide frequency range. An optimization based on the planning of experiments and response surface technique to minimize the error functional is applied to decrease considerably the computational expenses. The developed identification technique has been tested on aluminum panels and successfully applied to characterize viscoelastic material properties of 3M damping polymer ISD-112 used as a core material in sandwich panels.
Abstract: Explosion occurs due to sudden release of energy.
Common examples of explosion include chemical, atomic, heat, and
pressure tank (due to ignition) explosions. Petroleum, gas, and
petrochemical industries operations are threatened by natural risks
and processes. Fires and explosions are the greatest process risks
which cause financial damages.
This study aims at designing a single-floor structure for the control
room of a petroleum refinery to be resistant against gas explosion
loads, and the information related to the structure specifications have
been provided regarding the fact that the structure is made on the
ground's surface. In this research, the lateral stiffness of single pile is
calculated by SPPLN.FOR computer program, and its value for
13624 KN/m single pile has been assessed. The analysis used due to
the loading conditions, is dynamic nonlinear analysis with direct
integration method.
Abstract: Nonlinear finite element method and Serendipity eight
nodes element are used for determining of ground surface settlement
due to tunneling. Linear element with elastic behavior is used for
modeling of lining. Modified Generalized plasticity model with nonassociated
flow rule is applied for analysis of a tunnel in Sao Paulo –
Brazil. The tunnel had analyzed by Lades- model with 16 parameters.
In this work modified Generalized Plasticity is used with 10
parameters, also Mohr-Coulomb model is used to analysis the tunnel.
The results show good agreement with observed results of field data
by modified Generalized Plasticity model than other models. The
obtained result by Mohr-Coulomb model shows less settlement than
other model due to excavation.
Abstract: Genetic algorithms (GAs) have been widely used for
global optimization problems. The GA performance depends highly
on the choice of the search space for each parameter to be optimized.
Often, this choice is a problem-based experience. The search space
being a set of potential solutions may contain the global optimum
and/or other local optimums. A bad choice of this search space
results in poor solutions. In this paper, our approach consists in
extending the search space boundaries during the GA optimization,
only when it is required. This leads to more diversification of GA
population by new solutions that were not available with fixed search
space boundaries. So, these dynamic search spaces can improve the
GA optimization performances. The proposed approach is applied to
power system stabilizer optimization for multimachine power system
(16-generator and 68-bus). The obtained results are evaluated and
compared with those obtained by ordinary GAs. Eigenvalue analysis
and nonlinear system simulation results show the effectiveness of the
proposed approach to damp out the electromechanical oscillation and
enhance the global system stability.
Abstract: In this paper, a new dependable algorithm based on an adaptation of the standard variational iteration method (VIM) is used for analyzing the transition from steady convection to chaos for lowto-intermediate Rayleigh numbers convection in porous media. The solution trajectories show the transition from steady convection to chaos that occurs at a slightly subcritical value of Rayleigh number, the critical value being associated with the loss of linear stability of the steady convection solution. The VIM is treated as an algorithm in a sequence of intervals for finding accurate approximate solutions to the considered model and other dynamical systems. We shall call this technique as the piecewise VIM. Numerical comparisons between the piecewise VIM and the classical fourth-order Runge–Kutta (RK4) numerical solutions reveal that the proposed technique is a promising tool for the nonlinear chaotic and nonchaotic systems.
Abstract: This paper addresses linear quadratic regulation (LQR)
for variable speed variable pitch wind turbines. Because of the
inherent nonlinearity of wind turbine, a set of operating conditions is
identified and then a LQR controller is designed for each operating
point. The feedback controller gains are then interpolated linearly to
get control law for the entire operating region. Besides, the
aerodynamic torque and effective wind speed are estimated online to
get the gain-scheduling variable for implementing the controller. The
potential of the method is verified through simulation with the help of
MATLAB/Simulink and GH Bladed. The performance and
mechanical load when using LQR are also compared with that when
using PI controller.
Abstract: Robust nonlinear integrated navigation of GPS and
low cost MEMS is a hot topic of research these days. A robust filter
is required to cope up with the problem of unpredictable
discontinuities and colored noises associated with low cost sensors.
H∞ filter is previously used in Extended Kalman filter and Unscented
Kalman filter frame. Unscented Kalman filter has a problem of
Cholesky matrix factorization at each step which is a very unstable
operation. To avoid this problem in this research H∞ filter is
designed in Square root Unscented filter framework and found 50%
more robust towards increased level of colored noises.
Abstract: The paper presents the design of a mini-UAV attitude
controller using the backstepping method. Starting from the nonlinear
dynamic equations of the mini-UAV, by using the backstepping
method, the author of this paper obtained the expressions of the
elevator, rudder and aileron deflections, which stabilize the UAV, at
each moment, to the desired values of the attitude angles. The attitude
controller controls the attitude angles, the angular rates, the angular
accelerations and other variables that describe the UAV longitudinal
and lateral motions. To design the nonlinear controller, by using the
backstepping technique, the nonlinear equations and the Lyapunov
analysis have been directly used. The designed controller has been
implemented in Matlab/Simulink environment and its effectiveness
has been tested with a campaign of numerical simulations using data
from the UAV flight tests. The obtained results are very good and
they are better than the ones found in previous works.
Abstract: One of the most important parts of a cement factory is
the cement rotary kiln which plays a key role in quality and quantity of produced cement. In this part, the physical exertion and bilateral
movement of air and materials, together with chemical reactions take
place. Thus, this system has immensely complex and nonlinear dynamic equations. These equations have not worked out yet. Only
in exceptional case; however, a large number of the involved parameter were crossed out and an approximation model was
presented instead. This issue caused many problems for designing a
cement rotary kiln controller. In this paper, we presented nonlinear predictor and simulator models for a real cement rotary kiln by using
nonlinear identification technique on the Locally Linear Neuro-
Fuzzy (LLNF) model. For the first time, a simulator model as well as
a predictor one with a precise fifteen minute prediction horizon for a
cement rotary kiln is presented. These models are trained by
LOLIMOT algorithm which is an incremental tree-structure
algorithm. At the end, the characteristics of these models are expressed. Furthermore, we presented the pros and cons of these
models. The data collected from White Saveh Cement Company is used for modeling.
Abstract: In this paper, we consider the problem of tracking
multiple maneuvering targets using switching multiple target motion
models. With this paper, we aim to contribute in solving the problem
of model-based body motion estimation by using data coming from
visual sensors. The Interacting Multiple Model (IMM) algorithm is
specially designed to track accurately targets whose state and/or
measurement (assumed to be linear) models changes during motion
transition. However, when these models are nonlinear, the IMM
algorithm must be modified in order to guarantee an accurate track.
In this paper we propose to avoid the Extended Kalman filter because
of its limitations and substitute it with the Unscented Kalman filter
which seems to be more efficient especially according to the
simulation results obtained with the nonlinear IMM algorithm (IMMUKF).
To resolve the problem of data association, the JPDA
approach is combined with the IMM-UKF algorithm, the derived
algorithm is noted JPDA-IMM-UKF.
Abstract: In this paper, we have applied the homotopy perturbation
method (HPM) for obtaining the analytical solution of unsteady
flow of gas through a porous medium and we have also compared the
findings of this research with some other analytical results. Results
showed a very good agreement between results of HPM and the
numerical solutions of the problem rather than other analytical solutions
which have previously been applied. The results of homotopy
perturbation method are of high accuracy and the method is very
effective and succinct.
Abstract: In this paper, a TSK-type Neuro-fuzzy Inference
System that combines the features of fuzzy sets and neural networks
has been applied for the identification of MIMO systems. The procedure of adapting parameters in TSK model employs a Shuffled
Frog Leaping Algorithm (SFLA) which is inspired from the memetic evolution of a group of frogs when seeking for food. To demonstrate
the accuracy and effectiveness of the proposed controller, two nonlinear systems have been considered as the MIMO plant, and results have been compared with other learning methods based on
Particle Swarm Optimization algorithm (PSO) and Genetic
Algorithm (GA).
Abstract: In this study, an analysis has been performed for
heat and mass transfer of a steady laminar boundary-layer flow
of a viscous flow past a nonlinearly stretching sheet.
Parameters n, Ec, k0, Sc represent the dominance of the
nonlinearly effect, viscous effect, radiation effect and mass
transfer effect which have presented in governing equations,
respectively. The similarity transformation and the
finite-difference method have been used to analyze the present
problem.
Abstract: Photonic Crystal (PhC) based devices are being
increasingly used in multifunctional, compact devices in integrated
optical communication systems. They provide excellent
controllability of light, yet maintaining the small size required for
miniaturization. In this paper, the band gap properties of PhCs and
their typical applications in optical waveguiding are considered.
Novel PhC based applications such as nonlinear switching and
tapers are considered and simulation results are shown using the
accurate time-domain numerical method based on Finite Difference
Time Domain (FDTD) scheme. The suitability of these devices for
novel applications is discussed and evaluated.