Abstract: Because of importance of energy, optimization of
power generation systems is necessary. Gas turbine cycles are
suitable manner for fast power generation, but their efficiency is
partly low. In order to achieving higher efficiencies, some
propositions are preferred such as recovery of heat from exhaust
gases in a regenerator, utilization of intercooler in a multistage
compressor, steam injection to combustion chamber and etc.
However thermodynamic optimization of gas turbine cycle, even
with above components, is necessary. In this article multi-objective
genetic algorithms are employed for Pareto approach optimization of
Regenerative-Intercooling-Gas Turbine (RIGT) cycle. In the multiobjective
optimization a number of conflicting objective functions
are to be optimized simultaneously. The important objective
functions that have been considered for optimization are entropy
generation of RIGT cycle (Ns) derives using Exergy Analysis and
Gouy-Stodola theorem, thermal efficiency and the net output power
of RIGT Cycle. These objectives are usually conflicting with each
other. The design variables consist of thermodynamic parameters
such as compressor pressure ratio (Rp), excess air in combustion
(EA), turbine inlet temperature (TIT) and inlet air temperature (T0).
At the first stage single objective optimization has been investigated
and the method of Non-dominated Sorting Genetic Algorithm
(NSGA-II) has been used for multi-objective optimization.
Optimization procedures are performed for two and three objective
functions and the results are compared for RIGT Cycle. In order to
investigate the optimal thermodynamic behavior of two objectives,
different set, each including two objectives of output parameters, are
considered individually. For each set Pareto front are depicted. The
sets of selected decision variables based on this Pareto front, will
cause the best possible combination of corresponding objective
functions. There is no superiority for the points on the Pareto front
figure, but they are superior to any other point. In the case of three
objective optimization the results are given in tables.
Abstract: A two-dimensional moving mesh algorithm is developed to simulate the general motion of two rotating bodies with relative translational motion. The grid includes a background grid and two sets of grids around the moving bodies. With this grid arrangement rotational and translational motions of two bodies are handled separately, with no complications. Inter-grid boundaries are determined based on their distances from two bodies. In this method, the overset concept is applied to hybrid grid, and flow variables are interpolated using a simple stencil. To evaluate this moving mesh algorithm unsteady Euler flow is solved for different cases using dual-time method of Jameson. Numerical results show excellent agreement with experimental data and other numerical results. To demonstrate the capability of present algorithm for accurate solution of flow fields around moving bodies, some benchmark problems have been defined in this paper.
Abstract: Phrases has a long history in information retrieval, particularly in commercial systems. Implicit semantic relationship between words in a form of BaseNP have shown significant improvement in term of precision in many IR studies. Our research focuses on linguistic phrases which is language dependent. Our results show that using BaseNP can improve performance although above 62% of words formation in Malay Language based on derivational affixes and suffixes.
Abstract: Environmental awareness and the recent
environmental policies have forced many electric utilities to
restructure their operational practices to account for their emission
impacts. One way to accomplish this is by reformulating the
traditional economic dispatch problem such that emission effects are
included in the mathematical model. This paper presents a Particle
Swarm Optimization (PSO) algorithm to solve the Economic-
Emission Dispatch problem (EED) which gained recent attention due
to the deregulation of the power industry and strict environmental
regulations. The problem is formulated as a multi-objective one with
two competing functions, namely economic cost and emission
functions, subject to different constraints. The inequality constraints
considered are the generating unit capacity limits while the equality
constraint is generation-demand balance. A novel equality constraint
handling mechanism is proposed in this paper. PSO algorithm is
tested on a 30-bus standard test system. Results obtained show that
PSO algorithm has a great potential in handling multi-objective
optimization problems and is capable of capturing Pareto optimal
solution set under different loading conditions.
Abstract: With deep development of software reuse, componentrelated
technologies have been widely applied in the development of
large-scale complex applications. Component identification (CI) is
one of the primary research problems in software reuse, by analyzing
domain business models to get a set of business components with high
reuse value and good reuse performance to support effective reuse.
Based on the concept and classification of CI, its technical stack is
briefly discussed from four views, i.e., form of input business models,
identification goals, identification strategies, and identification
process. Then various CI methods presented in literatures are
classified into four types, i.e., domain analysis based methods,
cohesion-coupling based clustering methods, CRUD matrix based
methods, and other methods, with the comparisons between these
methods for their advantages and disadvantages. Additionally, some
insufficiencies of study on CI are discussed, and the causes are
explained subsequently. Finally, it is concluded with some
significantly promising tendency about research on this problem.
Abstract: Product Data Management (PDM) systems for Computer
Aided Design (CAD) file management are widely established
in design processes. This management system is indispensable for
design collaboration or when design task distribution is present. It is
thus surprising that engineering design curricula has not paid much
attention in the education of PDM systems. This is also the case
for eduction of ecodesign and environmental evaluation of products.
With the rise of sustainability as a strategic aspect in companies,
environmental concerns are becoming a key issue in design. This
paper discusses the establishment of a PDM platform to be used
among technical and vocational schools in Austria. The PDM system
facilitates design collaboration among these schools. Further, it will
be discussed how the PDM system has been prepared in order to
facilitate environmental evaluation of parts, components and subassemblies
of a product. By integrating a Business Intelligence
solution, environmental Life Cycle Assessment and communication
of results is enabled.
Abstract: To explore pipelines is one of various bio-mimetic
robot applications. The robot may work in common buildings such as
between ceilings and ducts, in addition to complicated and massive
pipeline systems of large industrial plants. The bio-mimetic robot finds
any troubled area or malfunction and then reports its data. Importantly,
it can not only prepare for but also react to any abnormal routes in the
pipeline. The pipeline monitoring tasks require special types of mobile
robots. For an effective movement along a pipeline, the movement of
the robot will be similar to that of insects or crawling animals. During
its movement along the pipelines, a pipeline monitoring robot has an
important task of finding the shapes of the approaching path on the
pipes. In this paper we propose an effective solution to the pipeline
pattern recognition, based on the fuzzy classification rules for the
measured IR distance data.
Abstract: Imperfect transmission conditions modeling a thin reactive 2D interphases layer between two dissimilar bonded strips have been extracted. In this paper, the soundness of these transmission conditions for heat conduction problems are examined by the finite element method for a strong temperature-dependent source or sink and non-monotonic temperature distributions around the faces..
Abstract: Cell formation is the first step in the design of cellular
manufacturing systems. In this study, a general purpose
computational scheme employing a hybrid tabu search algorithm as
the core is proposed to solve the cell formation problem and its
variants. In the proposed scheme, great flexibilities are left to the
users. The core solution searching algorithm embedded in the scheme
can be easily changed to any other meta-heuristic algorithms, such as
the simulated annealing, genetic algorithm, etc., based on the
characteristics of the problems to be solved or the preferences the
users might have. In addition, several counters are designed to control
the timing of conducting intensified solution searching and diversified
solution searching strategies interactively.
Abstract: Structural redundancy is an interesting point in
seismic design of structures. Initially, the structural redundancy is
described as indeterminate degree of a system. Although many definitions are presented for redundancy in structures, recently the
definition of structural redundancy has been related to the configuration of structural system and the number of lateral load
transferring directions in the structure. The steel frames with infill walls are general systems in the constructing of usual residential buildings in some countries. It is
obviously declared that the performance of structures will be affected by adding masonry infill walls. In order to investigate the effect of
infill walls on the redundancy of the steel frame which constructed
with masonry walls, the components of redundancy including redundancy variation index, redundancy strength index and
redundancy response modification factor were extracted for the
frames with masonry infills. Several steel frames with typical storey number and various numbers of bays were designed and considered.
The redundancy of frames with and without infill walls was evaluated by proposed method. The results showed the presence of infill causes increase of redundancy.
Abstract: Nondestructive testing in engineering is an inverse
Cauchy problem for Laplace equation. In this paper the problem
of nondestructive testing is expressed by a Laplace-s equation with
third-kind boundary conditions. In order to find unknown values on
the boundary, the method of fundamental solution is introduced and
realized. Because of the ill-posedness of studied problems, the TSVD
regularization technique in combination with L-curve criteria and
Generalized Cross Validation criteria is employed. Numerical results
are shown that the TSVD method combined with L-curve criteria is
more efficient than the TSVD method combined with GCV criteria.
The abstract goes here.
Abstract: A linear system is called a fully fuzzy linear system (FFLS) if quantities in this system are all fuzzy numbers. For the FFLS, we investigate its solution and develop a new approximate method for solving the FFLS. Observing the numerical results, we find that our method is accurate than the iterative Jacobi and Gauss- Seidel methods on approximating the solution of FFLS.
Abstract: In this work a new platform for mobile-health systems is
presented. System target application is providing decision support to
rescue corps or military medical personnel in combat areas. Software
architecture relies on a distributed client-server system that manages a
wireless ad-hoc networks hierarchy in which several different types of
client operate. Each client is characterized for different hardware and
software requirements. Lower hierarchy levels rely in a network of
completely custom devices that store clinical information and patient
status and are designed to form an ad-hoc network operating in the
2.4 GHz ISM band and complying with the IEEE 802.15.4 standard
(ZigBee). Medical personnel may interact with such devices, that are
called MICs (Medical Information Carriers), by means of a PDA
(Personal Digital Assistant) or a MDA (Medical Digital Assistant),
and transmit the information stored in their local databases as well as
issue a service request to the upper hierarchy levels by using IEEE
802.11 a/b/g standard (WiFi). The server acts as a repository that
stores both medical evacuation forms and associated events (e.g., a
teleconsulting request). All the actors participating in the diagnostic
or evacuation process may access asynchronously to such repository
and update its content or generate new events. The designed system
pretends to optimise and improve information spreading and flow
among all the system components with the aim of improving both
diagnostic quality and evacuation process.
Abstract: The paper deals with cartographic visualisation of
results of transport accessibility monitoring with the use of a semiautomated
method of unipolar anamorphosis, developed by the
authors in the GIS environment. The method is based on
transformation of distance in the map to values of a geographical
phenomenon. In the case of time accessibility it is based on
transformation of isochrones converted into the form of concentric
circles, taking into account selected topographic and thematic
elements in the map. The method is most suitable for analyses of
accessibility to or from a centre and for modelling its long-term
context.
The paper provides a detailed analysis of the procedures and
functionality of the method, discussing the issues of coordinates,
transformation, scale and visualisation. It also offers a discussion of
possible problems and inaccuracies. A practical application of the
method is illustrated by previous research results by the authors in
the filed of accessibility in Czechia.
Abstract: Time series analysis often requires data that represents
the evolution of an observed variable in equidistant time steps. In
order to collect this data sampling is applied. While continuous
signals may be sampled, analyzed and reconstructed applying
Shannon-s sampling theorem, time-discrete signals have to be dealt
with differently. In this article we consider the discrete-event
simulation (DES) of job-shop-systems and study the effects of
different sampling rates on data quality regarding completeness and
accuracy of reconstructed inventory evolutions. At this we discuss
deterministic as well as non-deterministic behavior of system
variables. Error curves are deployed to illustrate and discuss the
sampling rate-s impact and to derive recommendations for its wellfounded
choice.
Abstract: This paper examines whether or not immigration has a positive influence on the duration of unemployment, in a macroeconomic perspective. We analyse also whether the degree of labor market integration can influence migration. The integration of immigrants into the labor market is a recurrence theme in the work on the economic consequences of immigration. However, to our knowledge, no researchers have studied the impact of immigration on unemployment duration, and vice versa. With two methodology of research (panel estimations (OLS and 2SLS) and panel cointegration techniques), we show that migration seems to influence positively the short-term unemployment and negatively long-term unemployment, for 14 OECD destination countries. In addition, immigration seems to be conditioned by the structural and institutional characteristics of the labour market.
Abstract: A semi-active control strategy for suspension
systems of passenger cars is presented employing
Magnetorheological (MR) dampers. The vehicle is modeled with
seven DOFs including the, roll pitch and bounce of car body, and
the vertical motion of the four tires. In order to design an optimal
controller based on the actuator constraints, a Linear-Quadratic
Regulator (LQR) is designed. The design procedure of the LQR
consists of selecting two weighting matrices to minimize the energy
of the control system. This paper presents a hybrid optimization
procedure which is a combination of gradient-based and
evolutionary algorithms to choose the weighting matrices with
regards to the actuator constraint. The optimization algorithm is
defined based on maximum comfort and actuator constraints. It is
noted that utilizing the present control algorithm may significantly
reduce the vibration response of the passenger car, thus, providing
a comfortable ride.
Abstract: The Sensor Network consists of densely deployed
sensor nodes. Energy optimization is one of the most important
aspects of sensor application design. Data acquisition and aggregation
techniques for processing data in-network should be energy efficient.
Due to the cross-layer design, resource-limited and noisy nature
of Wireless Sensor Networks(WSNs), it is challenging to study
the performance of these systems in a realistic setting. In this
paper, we propose optimizing queries by aggregation of data and
data redundancy to reduce energy consumption without requiring
all sensed data and directed diffusion communication paradigm to
achieve power savings, robust communication and processing data
in-network. To estimate the per-node power consumption POWERTossim
mica2 energy model is used, which provides scalable and
accurate results. The performance analysis shows that the proposed
methods overcomes the existing methods in the aspects of energy
consumption in wireless sensor networks.
Abstract: This paper proposes evaluation of sound parameterization methods in recognizing some spoken Arabic words, namely digits from zero to nine. Each isolated spoken word is represented by a single template based on a specific recognition feature, and the recognition is based on the Euclidean distance from those templates. The performance analysis of recognition is based on four parameterization features: the Burg Spectrum Analysis, the Walsh Spectrum Analysis, the Thomson Multitaper Spectrum Analysis and the Mel Frequency Cepstral Coefficients (MFCC) features. The main aim of this paper was to compare, analyze, and discuss the outcomes of spoken Arabic digits recognition systems based on the selected recognition features. The results acqired confirm that the use of MFCC features is a very promising method in recognizing Spoken Arabic digits.
Abstract: This paper deals with the extraction of information from the experts to automatically identify and recognize Ganoderma infection in oil palm stem using tomography images. Expert-s knowledge are used as rules in a Fuzzy Inference Systems to classify each individual patterns observed in he tomography image. The classification is done by defining membership functions which assigned a set of three possible hypotheses : Ganoderma infection (G), non Ganoderma infection (N) or intact stem tissue (I) to every abnormalities pattern found in the tomography image. A complete comparison between Mamdani and Sugeno style,triangular, trapezoids and mixed triangular-trapezoids membership functions and different methods of aggregation and defuzzification is also presented and analyzed to select suitable Fuzzy Inference System methods to perform the above mentioned task. The results showed that seven out of 30 initial possible combination of available Fuzzy Inference methods in MATLAB Fuzzy Toolbox were observed giving result close to the experts estimation.